RSC Advances
·
2019
·Vol. 9
·期 59
·34581-34588
·
IF 3.049
Li Wang,Yue Zhang,Qingqing Ma,Zhiyong Pan,Baoning Zong
Organosilane-functionalized mesoporous silica SBA-15 was prepared by the co-condensation method and then applied as a support of Pd catalysts for hydrogenation of 2-alkyl-anthraquinone (AQ, alkyl = ethyl, tert-butyl and amyl). The as-prepared Pd catalysts were characterized by X-ray diffraction, Fourier transform infrared spectroscopy, thermogravimetric analysis, N2 adsorption–desorption, zeta potential, water contact angles measurement and transmission electron microscopy. By extending the pre-hydrolysis time of the silica source, the content of functional groups in the catalysts slightly increases. However, there is an initial increase in zeta potential and water contact angles up to a maximum at 2 h, followed by a decrease as the pre-hydrolysis time was further prolonged. The hydrophobicity created by organic functionalization has positive effects on AQ hydrogenation. The catalyst with the highest hydrophobicity exhibits the highest catalytic activity, with increments of 33.3%, 60.0% and 150.0% for hydrogenation of ethyl-, tert-butyl- and amyl-anthraquinone compared with the unfunctionalized one.
研究领域:
化学工程
·
催化科学
✓ 已验证
产品关联
DOI
PubMed
高影响因子
Catalysis Science & Technology
·
2015
·Vol. 6
·期 7
·2403-2412
·
IF 5.426
Dong Wang,Yujun Zhu,Chungui Tian,Lei Wang,Wei Zhou,Yongli Dong,Qing Han,Yunfei Liu,Fulong Yuan,Honggang Fu
The introduction of a suitable co-catalyst is a promising way to improve the catalytic efficiency of Pt catalysts. Herein, SBA-15 modified with well-dispersed Mo2N nanoparticles (NPs) is synthesized by anchoring phosphomolybdic acid (HPM) on aminated SBA-15 (SBA-15-NH2) primarily, followed by nitridation treatment under NH3. After loading of Pt, the Pt–Mo2N/SBA-15 catalyst with close-contact Pt and Mo2N NPs can be formed. The intensive interaction of Pt and Mo2N benefited from the close contact is verified by XRD and XPS tests. As a result, the ternary Pt–Mo2N/SBA-15 catalysts have shown superior performance to Pt/SBA-15 catalysts for the selective hydrogenation of cinnamaldehyde to cinnamyl alcohol. The TOF over the 1 wt% Pt–Mo2N/SBA-15 catalyst is close to that over the 3 wt% Pt/SBA-15 catalyst, but its selectivity to cinnamyl alcohol (COL) is 2.5 times that of 3 wt% Pt/SBA-15. The promoted activity of Pt–Mo2N/SBA-15 is mainly attributed to the synergistic effect of Pt and Mo2N NPs, which can cause the full development of the catalytic ability of Pt, thus reducing the Pt usage, through increasing the dispersion of Pt NPs and the fraction of Pt0 species in the catalyst.
研究领域:
催化化学
·
材料科学
✓ 已验证
产品关联
DOI
高影响因子
OPTICAL MATERIALS
·
2018
·
IF 2.32
Zhongyu Wang,Ying Li,Hao Hu,Xia Wang
Novel organic-inorganic mesoporous luminescent polymeric composite materials containing lanthanide (Eu 3+ , Tb 3+ ) complexes covalently bonded to mesoporous silica have been prepared in situ, followed by the polymerization reaction of the monomer 4-vinylphenylboronic acid (VPBA) extending along the mesoporous SBA-15 channels. The obtained materials were investigated by Fourier transform infrared spectroscopy (FT-IR), Ultraviolet absorption spectra (UV), X-ray diffraction (SAXRD), N 2 adsorption/desorption isotherms, Transmission electron microscopy (TEM), thermogravimetry (TG), and luminescence spectroscopy in detail. These characterizations have proved that composite materials possess high surface area, uniform mesoporous structure, good crystallization and relatively excellent luminescence properties. The terminal ligand phen was used to investigate the difference of photo physical and luminescent properties between binary and ternary composite materials. Furthermore, the results have revealed that the composite material Eu(PVPBA-S15) 3 phen showed more efficient intramolecular energy transfer between the europium ion and the ligands, and more excellent characteristic emission of the europium ion under UV irradiation with higher 5 D 0 luminescence quantum efficiency than the composite materials Eu(PVPBA-S15) 3 without phen. The excellent luminescence properties and ordered mesoporous structures could give rise to many potential applications in optical and electronic areas.
研究领域:
材料科学
·
光学
✓ 已验证
产品关联
DOI
高影响因子
NEW JOURNAL OF CHEMISTRY
·
2023
·Vol. 47
·期 26
·12314-12319
·
IF 3.3
Guofeng Wang,Wenwen Gao,Dong Yun,Chuanzhi Xu,Zhen Li,Chungu Xia
Silica-based mesoporous materials, such as SBA-15, are important supports in the field of catalysis due to their ordered pore channels. The traditional synthesis route of SBA-15 suffers from high autogenous pressure and explosion risks, limiting its industrial production. Herein, a reflux system under ambient pressure was used for the synthesis of SBA-15. Ni nanoparticles were incorporated into the obtained materials to evaluate the quality of the SBA-15 support. The comparative performance of Ni/SBA-15H and Ni/SBA-15R validated there was negligible difference between the SBA-15 prepared by the hydrothermal method (SBA-15H) and the reflux method (SBA-15R). This revolutionary synthesis methodology provides a novel and secure route for the large-scale preparation of SBA-15.
研究领域:
材料科学
·
催化化学
✓ 已验证
产品关联
DOI
高影响因子
INTERNATIONAL JOURNAL OF HYDROGEN ENERGY
·
2020
·
IF 4.939
Zhang Haocui,Xiao Zhourong,Yang Mei,Tian Yajie,Li Guozhu,Zhang Xiangwen,Liu Guozhu
As the only H 2 resource on aircraft from the steam reforming of the jet fuels on board, catalytic steam reforming of JP-10 (one of Jet fuels) over nickel-based catalyst Ni/SBA-15 were first carried out in a fixed bed tube reactor to produce hydrogen on-site or on board. A series of Ni/SBA-15 catalysts with different Ni content (3, 5, 8 and 10.8 wt%) were prepared by a modified incipient wetness impregnation method with addition of sucrose as ligand. And the effect of operation conditions of temperature (630–700 °C), nickel loading, liquid hour space velocity (LHSV = 5, 10, 15 ml/g cat ·h), steam to carbon molar ratio (S/C = 3, 5) on the catalytic activity and selectivity was investigated. It was found that 8Ni/SBA-15 was the optimal catalyst for steam reforming of JP-10 even with a higher LHSV and fuel gas concentration, and approximately 100% conversion of JP-10 with over 80% selectivity to hydrogen under the recommended experimental conditions of 680 °C, S/C of 5, LHSV of 10 ml/g cat ·h. The catalytic activity of 8Ni/SBA-15 dropped slowly to 84% after 6.5 h in the stability test and the carbon deposited was less with just 6% mass loss from TGA measurement (coke deposition rate 0.01g C /g cat h), which ascribed to possible reasons including confine effect of mesochannel of SBA-15, strengthened structure of mesochannels due to embeded Ni particles, and higher temperature to suppress the main carbon producing reaction.
研究领域:
化学工程
·
能源科学
✓ 已验证
产品关联
DOI
高影响因子
INDUSTRIAL & ENGINEERING CHEMISTRY RESEARCH
·
2018
·
IF 3.141
Yuan Cai,Xiaofeng Xu,Hu Wang,Lei Wang,Lulu Chen,Rui Li,Jing Ding,Hui Wan,Guofeng Guan
Production of alternative, clean aviation fuel from biomass synthesis gas via Fischer–Tropsch (FT) synthesis has attracted much attention. In this paper, Al-SBA-15 supported cobalt catalysts with different Al/Si ratios were successfully prepared for the production of aviation fuel by FT synthesis. The physical and acidic properties of the Co/Al-SBA-15 catalysts were characterized by XRF, XRD, N2 adsorption–desorption, TEM, H2-TPR, 27Al NMR, NH3-TPD, and Py-FTIR. The formation of long-chain hydrocarbons was inhibited by the ordered mesoporous structure. Fischer–Tropsch activity and selectivity were demonstrated to be affected by the acidity of the Al-SBA-15 supports. The selectivity turned to lighter iso-paraffin products. Co-based catalyst with Al/Si ratio of 0.01 exhibited the highest selectivity (52.4%) for aviation fuel (C8–C18 products) and much higher ratio of iso-paraffin/normal-paraffin (iso/n) (20.2%). This study might provide useful information for the selective production of aviation fuel via FT synthesis.
研究领域:
化学工程
·
能源科学
✓ 已验证
产品关联
DOI
高影响因子
RENEWABLE ENERGY
·
2023
·
IF 8.7
Shanshuai Chen,Puxiang Yan,Xiaona Yu,Wanbin Zhu,Hongliang Wang
The development of a highly active and robust catalyst for the conversion of lignin, the largest volume of renewable aromatic resource in nature, to value-added aromatics is of great importance in sustainable chemistry. However, the condensation of lignin depolymerization intermediates into recalcitrant macromolecules restricts high yields of desired products, and this remains a great challenge in lignin valorization. Here, a serious of bifunctional Ru–ZnO/SBA-15 catalysts were synthesized for lignin conversion to aromatics. Roles of Ru and ZnO in these catalysts for lignin conversion were in-depth analyzed. The effect of the ratio of Ru to ZnO was studied. Other reaction conditions including temperature and time were systematically optimized. More than 51.3% yields of aromatics were obtained over Ru–10ZnO/SBA-15 at 240 °C for 4 h. Structure-activity relationship research of the catalyst revealed that the high yield of product could be attributed to the following three reasons: 1) the Lewis acidic sites on Ru/SBA-15 are significantly improved after ZnO modification, and thus promotes the C–O bond cleavage ; 2) the oxophilic ZnO is beneficial to absorb the substrate and reaction intermediates, and therefore enhances the hydrodeoxygenation activity of the adjacent Ru; 3). The interaction between Zn and Ru in Ru–ZnO/SBA-15 changes Ru electronic properties and leads to the formation of highly active catalytic sites with high electron density. These results indicated that the bifunctional Ru–ZnO/SBA-15 catalyst with high catalytic activity could be a good choice for lignin conversion to high-yield aromatics.
研究领域:
化学工程
·
可再生资源利用
✓ 已验证
产品关联
DOI
高影响因子
Catalysis Science & Technology
·
2021
·Vol. 11
·期 10
·3609-3618
·
IF 6.119
Palle Ramana Murthy,Jing-Cai Zhang,Wei-Zhen Li
Pd-Based catalysts are efficient for methane combustion but impractical at high temperatures due to the sintering effect. Herein, we report a thermally stable Pd/SBA-15 catalyst that was prepared by using the sol-immobilization (SI) method, instead of the conventional incipient wetness impregnation (IWI) method. Pd nanoparticles retain the small size of ∼5 nm in the channels of SBA-15 in Pd/SBA-15-SI even after aging at 800 °C in air for 3 days, while those in the Pd/SBA-15-IWI samples aggregate into particles larger than 10 nm over the surface. The thermally stable Pd/SBA-15-SI indeed displays excellent catalytic activity for methane combustion at low temperatures with T50 at ∼300 °C and T90 at ∼350 °C and high stability during cyclic operations, which are much superior to those of the Pd/SBA-15-IWI catalysts. Interestingly, hydrothermal treatment of the Pd/SBA-15-SI catalysts leads to partial re-dispersion of Pd to form smaller particles of ∼1.6 nm, while the catalytic activity decreases a bit. Steam in the reactant mixture has a negative effect on the catalytic activity of Pd/SBA-15-SI catalysts, presumably due to the competitive adsorption of H2O to O2/CH4. Significantly, the size of Pd nanoparticles is essential to the catalytic performance and those having sizes of ∼5 nm are the most active. Finally, the catalytic activity of the catalysts in the presence of CO2 was studied. This work might be helpful in designing stable metal catalysts using porous materials for reactions under harsh conditions.
研究领域:
催化化学
·
材料科学
·
环境科学
✓ 已验证
DOI
高影响因子
JOURNAL OF SUPERCRITICAL FLUIDS
·
2014
·
IF 2.571
Qin-Qin Xu,Yu-Ling Ma,Gang-Xu,Jian-Zhong Yin,Ai-Qin Wang,Jin-Ji Gao
Well-defined Ag nanowires were obtained in SBA-15 at a short deposition time of 5 min in supercritical CO 2 when adding a small amount of ethylene glycol as the co-solvent. Ethylene glycol played a key role in dictating the nanowire morphology. Through detailed investigation of the whole deposition process, including the dissolution of precursor assisted by the co-solvent, the diffusion properties of the precursor into the nano-scale channels of the substrate, and the interaction between the precursor and the substrate, we found that a small amount of precursors were reduced into Ag 0 by ethylene glycol at the initial stage of the deposition. The resultant Ag 0 then acted as nuclei leading to a non-equilibrium sorption of the precursor. The rapid adsorption of the precursor onto the substrate resulted in a high loading of Ag in a short deposition time and the formation of nanowire morphology. Furthermore, this method was successfully extended to other porous substrates such as γ-Al 2 O 3 , SiO 2 and KIT-6, demonstrating its great potentials in the synthesis of nanocomposites.
研究领域:
材料科学
·
化学工程
✓ 已验证
产品关联
DOI
高影响因子
Catalysis Science & Technology
·
2023
·Vol. 13
·期 22
·6561-6569
·
IF 5
Songlei Mo,Yong Guo,Xiaohui Liu,Yanqin Wang
The glycolysis of polyethylene terephthalate (PET) is considered as the most promising PET recycling strategy due to its mild reaction conditions and circularity. Herein, several metal-doped SBA-15 (M/SBA-15) as heterogeneous Lewis acid catalysts were investigated to screen the best catalyst and to understand the essence for their differences in PET glycolysis. It is found that the catalytic activity is positively correlated with the acid amount in different metal-doped SBA-15 and Ti/SBA-15 with different Ti loadings, with the exception of Nb/SBA-15. 4Ti/SBA-15 with abundant Lewis acid sites shows excellent PET glycolysis ability, with the yield of bis(2-hydroxyethyl) terephthalate (BHET) reaching 87.2% within 45 min at 190 °C (isolated yield 73%). While 4Nb/SBA-15 has a similar acid amount as that in 4Ti/SBA-15, but it has very low catalytic activity probably due to its strong oxygen affinity. Acetone–methanol-adsorption DRIFTS confirms its strong oxygen affinity, which would poison the acid sites by ethylene glycol (EG) and result in very low activity. This study demonstrates that PET glycolysis activity is really correlated with the amount of Lewis acid sites, but species with very strong oxygen affinity would lower its activity. Further diffuse reflection ultraviolet-visible (DR UV-vis) spectra analysis confirms that tetrahedral Ti4+ species in Ti/SBA-15 is the real active center. In addition, 4Ti/SBA-15 has good reusability and can be used in common real PET (dyed polyester fabric, PET bottles) glycolysis. These results indicate that increasing the amount of Lewis acid sites is a promising way to enhance PET glycolysis and 4Ti/SBA-15 with high activity and stability is a potential catalyst for industrial application.
研究领域:
材料科学
·
催化化学
·
环境科学
✓ 已验证
产品关联
DOI
高影响因子
MICROPOROUS AND MESOPOROUS MATERIALS
·
2018
·
IF 3.649
Manman Jin,Jinkai Wang,Bing Wang,Zhenmei Guo,Zhiguo Lv
A simple and eco-friendly approach for green oxidation of aldehydes has been proposed, which employed highly efficient heterogeneous catalysts tungsten-doped modified silica SBA-15 (W-SBA-15) as catalysts and H 2 O 2 as a green oxidant. W-SBA-15 were synthesized by immobilizing tungsten species on modified SBA-15 and first used in the aldehydes oxidation reaction. W-SBA-15-APTS (0.002 g, APTS, a kind of modifier) displayed an equivalent catalytic activity comparable to that of homogenous catalyst (H 2 WO 4 , 0.5 g) and maintained excellent catalytic activity over 20 cycles. The pore diameter, ca . 7.94–9.14 nm, of W-SBA-15 provides a suitable mesoscopic environment for the substrate, and the product can diffuse freely during the oxidation of glutaraldehyde (GA). Effective but different catalytic performance of W-SBA-15 for the oxidation of other aldehydes suggests the universal applicability of W-SBA-15. The possible mechanism of the oxidation state of tungsten species in W-SBA-15-APTS was proposed; tungsten species are not only attached to APTS but also incorporated into the framework of SBA-15.
研究领域:
化学
·
环境科学
✓ 已验证
产品关联
DOI
高影响因子
ACS Applied Materials & Interfaces
·
2025
·
IF 8.2
Xiao Dan Sun,Zhangxin Duan,Jingjing Song,Hanxing Yang,Kai Yan,Zhenhua Tian,Dangge Gao,Jianzhong Ma
Carcinogen Cr(VI) is reduced efficiently into Cr(III) by a photocatalyst, but the produced Cr(III) is difficult to transfer from the photocatalytic active site. The “two birds with one stone” strategy is proposed to realize the in situ growth of ZnIn2S4 nanoplates on SBA-15 and the creation of separated active sites, in which ZnO loading on the porous SBA-15 nanorod was used as a zinc source. Obtained samples ZnIn2S4/SBA-15 (ZIS/SBA) showed the redshift of the absorption band and better separation of photoinduced carriers than pristine ZnIn2S4, due to its smaller size and S defect. All of the Cr(VI) was reduced to Cr(III) by the ZIS/SBA sample during the photocatalytic process, which was 2 times higher than pristine ZnIn2S4. Moreover, 92.8% of Cr(III) was adsorbed simultaneously during photocatalysis due to the electrostatic interaction from SBA-15. In addition, the ZIS/SBA sample showed good recycling stability after 5 times cycles, providing a new strategy for the in situ growth of ZnIn2S4 on the surface of porous materials and a novel way for the simultaneous removal of Cr(VI) and Cr(III) during photocatalysis.
研究领域:
环境科学
·
材料科学
✓ 已验证
产品关联
DOI
PubMed
高影响因子
危险品化学品经营许可证（带存储）