MOLECULES
·
2026
·Vol. 31
·期 12
·1997
·
IF 5.1
Fang Shi,Weibin Jin,Jingchun Wu,Bo Zhao,Chunlong Zhang,Lifeng Mao
To address gas channeling, low sweep efficiency, and water sensitivity in CO2flooding of shale reservoirs, amidine-functionalized graphene quantum dots (FN-GQDs) were synthesized via amidation of citric acid-derived GQDs. FTIR and UV-Vis confirmed successful grafting. Conductometric titration showed an optimal reaction time of 24 h with a grafting ratio of 58%, in good agreement with the 60% saturation predicted by molecular dynamics simulation. Upon CO2introduction, protonation of amidine groups induced a nonlinear viscosity increase from 0.298 to 2.0 mPa·s at 0.02 wt% via electrostatic attraction and hydrogen bonding, forming a dynamic crosslinking network. FN-GQDs maintained low oil-water interfacial tension of 0.12–0.25 mN/m at 80–120 °C and rapidly reversed rock wettability from strongly oil-wet to water-wet, reducing the contact angle from 141.7° to 38.9° within 80 min. The positively charged surface inhibited clay swelling, achieving 92% at 0.20 wt%. Core flooding and NMR T2spectra revealed that alternating CO2and FN-GQDs injection at a 2:1 gas–water ratio achieved a final oil recovery of 52.5%, significantly higher than pure CO2flooding. Through synergistic effects of interfacial tension reduction, wettability alteration, viscosity enhancement, and anti-swelling, FN-GQDs improve microscopic displacement efficiency and macroscopic sweep volume, showing great potential for CO2-enhanced oil recovery in shale reservoirs.
✓ 已验证
DOI
PubMed
高影响因子
Nanomaterials
·
2026
·Vol. 16
·期 12
·715
·
IF 4.8
Wendi Xu,Jia Zhang,Junjie Xie,Tianzhu Xu,Jia Wu,Hong Wang
Physical unclonable function (PUF) based on intrinsic device randomness has emerged as promising hardware security primitives, yet combining secure encryption with neuromorphic recognition within a single device platform remains challenging. Here, we demonstrate a photosensing PUF based on an intrinsically random SnTe memristor capable of both image encryption and memristive neural network recognition. The SnTe memristor, fabricated with an In2O3:SnO2/SnTe/Nb:SrTiO3structure, exhibits stable resistive switching and stable retention exceeding 4000 s. Synaptic biomimetic behaviors including learning-experience emulation, short-term plasticity and long-term plasticity are also realized. Notably, the device displays pronounced optical sensitivity that produces stochastic photocurrent fluctuations originating from unavoidable device-to-device variations under illumination. By quantizing these random photocurrents, an encryption key stream is generated and utilized for image scrambling and diffusion. A memristive neural network is constructed to classify the encrypted images, achieving a recognition accuracy of 95.1% with a loss of 0.15 after 300 training epochs. This work establishes a viable pathway from intrinsic optical randomness to secure neuromorphic computing, highlighting the multifunctional potential of SnTe memristors in integrated hardware security and brain-inspired computation.
✓ 已验证
DOI
PubMed
高影响因子
Biology-Basel
·
2026
·Vol. 15
·期 12
·906
·
IF 4.3
Chun Wang,Zhongquan Jiang,Jingyu Ma,Meilin He
Simple SummaryMicroplastics pollution threatens aquatic organisms, but what is puzzling is why the toxic effects of microplastics on microalgae become stronger or weaker with prolonged exposure. A key suspect is the gradual depletion of nutrients as algae grow. We examined whether nutrient levels alter the impact of polyvinyl chloride microplastics onDesmodesmussp. We cultured the algal cells with nutrient supplies ranging from rich to extremely poor (100%, 25%, 8%, and 4% of initial medium nutrient levels) and added different amounts of polyvinyl chloride microplastics. Under moderately low nutrients (25% nutrient level), the microplastics reduced growth and impaired photosynthesis. However, under severely nutrient-depleted conditions (4% nutrient level), the same microplastics enhanced growth and improved the algae’s light-use efficiency. A mathematical model for combined stress revealed that as nutrients dwindled, the interaction switched from synergistic harm to antagonism. This finding demonstrates that nutrient availability can dictate whether microplastics are harmful or beneficial, potentially offering a different perspective for understanding time-varying microplastic toxicity.Microplastics (MPs) have been shown to exert time-dependent toxic effects on microalgae, with toxicity either intensifying or alleviating over prolonged exposure. However, the underlying mechanisms driving this phenomenon remain unclear, particularly regarding the role of external nutrient depletion in the surrounding medium. Herein, we performed bioassays and computational modeling to evaluate the effects of polyvinyl chloride microplastics (mPVC, 10, 50, and 100 mg L−1) on the growth and physiology ofDesmodesmussp. under varying initial medium nutrient levels (100%, 25%, 8%, and 4%) for 96 h. The results demonstrated that nutrient levels in the culture medium modulated the toxic impact of mPVC. Under a 25% nutrient concentration, exposure to 100 mg L−1mPVC significantly inhibited algal growth by 6.5%, whereas at a 4% nutrient level, the growth ofDesmodesmussp. was significantly enhanced by 7.0%. Consistently, mPVC exposure at 25% nutrient concentration led to a sharper decline in intracellular pigment content (13.1–15.5%), soluble sugars content (8.2–27.0%), and photosynthetic efficiency (4.3–20.5%). In contrast, exposure to mPVC at 4% nutrient level improved the light use efficiency (11.9–15.4%) and electron transport rate (9.2–13.9%) of the algal cells. Independent action modeling revealed that as medium nutrient levels decreased, the interaction effects of mPVC exposure shifted from a synergistic to an antagonistic relationship. Overall, our findings identify medium nutrient availability as a critical regulatory factor influencing the toxic effects of mPVC on microalgae, potentially providing different insights into understanding the time-dependent toxicity of MPs.
✓ 已验证
DOI
PubMed
高影响因子
Agriculture-Basel
·
2026
·Vol. 16
·期 12
·1272
·
IF 4.5
Xiang Li,Ziyi Wu,Zijian Jiang,Junwei Zhang,Shuai Liu,Jianguo Feng
Developing zinc oxide-based nano-bactericides as alternatives to conventional chemical bactericides for controlling rice bacterial diseases has become a major research focus. In this study, ZnO nanoparticles were initially surface-modified and subsequently covalently conjugated with chitooligosaccharide (COS)viaimine bonds to get a pH-responsive zinc oxide–chitooligosaccharide (ZnO–COS) delivery system. A series of physicochemical characterizations, including FTIR, UV-vis, XRD, and TGA, confirmed the successful synthesis of ZnO–COS NPs. Building on this foundation, the pH-responsive release behavior, foliar deposition performance, antibacterial activity, and biosafety of the nanoparticles were systematically investigated. The prepared ZnO–COS NPs exhibited pronounced acid-triggered Zn2+release, together with enhanced wettability, spreadability, and retention on rice leaf surfaces, owing to COS incorporation. In both in vitro and in vivo assays againstXanthomonas oryzaepv.oryzae(Xoo), ZnO–COS NPs demonstrated effective antibacterial activity associated with bacterial cell damage and the activation of antioxidant defense responses in plants. Consequently, ZnO–COS NPs achieved a preventive efficacy of 56.0% against rice bacterial blight, surpassing those of ZnO (33.3%) and COS (14.3%). Furthermore, safety assessment confirmed the good biocompatibility of ZnO–COS NPs towards rice seed germination and seedling growth. In summary, the synthesised ZnO–COS NPs integrated pH-responsive release, improved foliar deposition, and enhanced antioxidant capacity of rice, offering a promising strategy for mitigating bacterial diseases in rice.
✓ 已验证
DOI
高影响因子
INORGANIC CHEMISTRY
·
2026
·
IF 4.6
Bo Yang,Li Cui,Hefeng Yuan,Hualin Zhang,Yu Che,Fangqin Cheng
Efficient separation of lithium isotopes (6Li and 7Li) is critical for sustainable nuclear energy. The crown ether system exhibits outstanding lithium isotope separation performance, with the anion exerting a significant influence; however, the molecular-level mechanism of action of anions and how this affects the separation process remain unclear. This limits the design of higher performance separation systems. Through combining 6Li/7Li separation experiments, 7Li NMR spectroscopy, and quantum chemical calculations, this work makes it clear that anions control the separation factor by changing the Li+ coordination microenvironment. Through manipulation of hydration and crown ether encapsulation, charge-delocalized anions provide a coordinating environment around Li+ that balances the bond strengths inside a crown-ether container. This balance of the bonding state improves the thermodynamic driving force for the 6Li/7Li exchange between the aqueous and organic phases and substantially increases the separation coefficient. This study provides an efficient screening method for lithium isotope separation and offers theoretical guidance for designing and optimizing more efficient lithium isotope separation systems.
✓ 已验证
产品关联
DOI
PubMed
高影响因子
ACS Applied Energy Materials
·
2026
·
IF 5.5
Wenlin Zhang,Shaoyue Chen,Lu-Hua Zhang,Fengshou Yu
The development of Fe single-atom catalysts has gained attention as a promising replacement for commercial Pt/C in the oxygen reduction reaction (ORR). However, transition-metal single-atom electrocatalysts generally suffer from sluggish catalytic kinetics due to unfavorable electronic structures and inappropriate adsorption strengths toward oxygen-containing intermediates. Herein, an atomically dispersed Fe catalyst supported on a three-dimensional porous carbon (FeNC/S) with sulfur incorporated into the carbon matrix was successfully synthesized. Experimental analyses combined with theoretical investigations confirm that S introduction modulated the electronic structure of the Fe active sites, inducing a transition in the Fe d-orbital spin state from a low-spin configuration (t2g6 eg0) to an intermediate-spin configuration (t2g5 eg1). The resulting intermediate-spin Fe sites enhance O2 activation and the adsorption of ORR intermediates, accelerating the ORR kinetics. Consequently, the FeNC/S catalyst displayed markedly enhanced ORR performance over commercial Pt/C, achieving a half-wave potential of 0.904 V. Additionally, the FeNC/S catalyst delivered a notable power density of 168 mW cm−2 upon application in an alkaline Zn−air battery, and stable operation was maintained for 200 h.
✓ 已验证
DOI
高影响因子
ACS Applied Materials & Interfaces
·
2026
·
IF 7.8
Lun Zhang,Zuyang Yin,Chengyang Wang,Ziying Wen,Mei Lyu,Jun Zhu
The severe nonradiative recombination losses in Cs2AgBiBr6 solar cells limit the enhancement of their open circuit voltage (VOC). Enhancing the built-in electric field (BEF) can help suppress the nonradiative recombination and effectively reduce the VOC and power conversion efficiency (PCE) losses. In this study, we introduced ferroelectrics diisopropylammonium hydrobromide (DIPAB) as an interfacial layer between the Cs2AgBi0.997Fe0.003Br6 film and the hole transport layer Spiro-OMeTAD in Cs2AgBi0.997Fe0.003Br6 solar cells. The ferroelectricity of DIPAB increases the BEF significantly. Additionally, the incorporation of DIPAB effectively passivates the defects and optimizes the energy-level alignment. Ultimately, DIPAB-modified Cs2AgBi0.997Fe0.003Br6 solar cells achieve a PCE enhancement from 2.81% to 3.43% and yield a VOC of up to 1.295 V, which is among the highest VOC documented for Cs2AgBiBr6 solar cells to date. Moreover, the unencapsulated DIPAB-modified Cs2AgBi0.997Fe0.003Br6 solar cells maintain 86% of its initial PCE after aging for 30 days at 25 ± 5 °C and 60 ± 5% relative humidity and 88% after aging for 300 h at 60 °C in a nitrogen glovebox. This study highlights the significance of ferroelectrics in enhancing the performance and stability of Cs2AgBiBr6 solar cells.
✓ 已验证
DOI
PubMed
高影响因子
ACS Applied Materials & Interfaces
·
2026
·
IF 7.8
Xiangxue Lv,Haimin Li,Shijie Ren,Zheng Zhang,Haohui Li,Bo An,Yuhao Wei,Jia Liao,Xingchong Liu,Hanyu Wang
Thiourea has been employed for the modification of perovskite (PVK) films and demonstrates favorable modification effects. However, few studies have addressed the binding mode of thiourea (Th) with perovskite crystal facets. In this work, DFT calculations reveal that thiourea exhibits a perpendicular binding orientation to the (100) facet of perovskite, enabling the lone pair electrons of the S atom in the C═S bond to interact with undercoordinated Pb atoms. Meanwhile, due to charge transfer, the −NH2 group and the S atom form bonds with positively charged sites in perovskite. PL, TRPL, SCLC, and KPFM results indicate a significant reduction of defects in the PVK. Eventually, the Th-perovskite device yielded a notable improvement in performance: open-circuit voltage (VOC) increased from 1.12 to 1.16 V, short-circuit current density (JSC) rose from 24.48 to 25.13 mA/cm2, the fill factor (FF) reached 82.35%, and the power conversion efficiency (PCE) was enhanced from 21.90% to 24.01%. Importantly, the devices retained 80% of their initial efficiency after operating for 15 days under 50% relative humidity, demonstrating significant progress in moisture tolerance for practical applications. This work highlights that vertical binding of small organic molecules to the perovskite facet surface can more effectively enhance the performance of photovoltaics.
✓ 已验证
DOI
PubMed
高影响因子
ACS Applied Polymer Materials
·
2026
·
IF 5.2
Wenbo Luan,Xiaodong Sui,Xiaoling Jian,Like Chang,Jiawei Xu,Longhai Guo,Teng Qiu,Jun Ye,Xinlin Tuo
The inherent trade-off among colloidal stability, reliable mechanical performance under thermal and thermo-oxidative aging, and reprocessability remains a critical bottleneck limiting the broader technological application of waterborne polyurethanes (WPU). Herein, inspired by the concepts of biomimetic artificial foldamers and reversible covalent cross-linking, we demonstrate an WPU system characterized by the synergism of a rigid poly(p-phenylene sulfone amide) based physical network and flexible thioctic acid (TA)-based dynamic S–S network. The strong interactions between PSA segments contribute to ordered H-bonding and π–π stacking, and the sulfone groups contribute to the improved thermal stability and the copolymerization compatibility with WPU. The TA linkages function as supplementary cross-linking and antioxidants, and their flexibility and metathesis reactions provide the kinetic possibility for the adjustment and rearrangement of the PSA network. Well-dispersed dispersion was constructed and produced an excellent elastomer by film formation. In comparison with the controlled blank sample, the dual network exhibited an increase on the tensile strength of 2.4 folds at room temperature, 67 folds at a high temperature of 120 °C, 7.2 folds after 7 days of aging at 120 °C, and 25 folds after three times of reprocessing by thermal pressing. The relatively high elongation at break and good toughness were also largely maintained under all the conditions. The heat deflection temperature increased by 133 °C. The rigid–flexible dual-network WPU, featuring unique environmental friendliness, operation feasibility together with unique thermal robustness, mechanical adaptability, and dynamic network reconfiguration capability represents an effective material platform for the potential high-end use such as high-temperature flexible electronics, stress-buffering components, and reconfigurable elastomeric structures.
✓ 已验证
DOI
高影响因子
ACS Applied Nano Materials
·
2026
·
IF 5.8
Kun Chen,Guomin Ding,Luyao Wang,Yuntian Luo,Zhengyang Lu,Borui Zheng,Hong Wang,Zihao Zhang,Qilin Mei
Graphene aerogels (GAs) have been widely recognized as ideal candidate materials for numerous applications; however, they still face drawbacks in terms of low strength and insufficient elasticity. Inspired by cellular structures, this study employs a high-melting-point aromatic oil phase to prepare the stable graphene oxide Pickering emulsion. Owing to its special sequential freezing behavior, the emulsion effectively suppresses ice crystal growth and successfully constructs a hierarchical microsphere/wall structure. Besides, due to the strong interaction between the oil molecules and graphene, the adsorbed oil phase can provide a healing effect for graphene nanosheets during the thermal reduction process. Based on these findings, the obtained pure GA exhibits significantly improved compression strength, which is more than 6 times higher than that of the common GA (CGA). More importantly, this GA exhibits a decreasing apparent density, resulting in an outstanding specific strength as high as 31.9 kN·m/kg and a recovery rate of 93.7% after 90% strain compression, a performance not yet achieved in reported studies. The formation and enhancement mechanism of the hierarchical microsphere/wall structure of GA is also studied in detail. Benefiting from its pure graphene composition and reversible compression properties, this aerogel serves as a potential material for thermal switches, achieving an ultrahigh switching ratio of 38.6 and enabling wide-range regulation of heat transfer capabilities. Therefore, this study demonstrates an accessible strategy to prepare lightweight, high strength, and elastic GAs, which can be excellent candidates for thermal management systems.
✓ 已验证
DOI
高影响因子
ORGANIC PROCESS RESEARCH & DEVELOPMENT
·
2026
·
IF 3.3
Andong Yu,Xuhai Pan,Funao Sang,Min Hua,Juncheng Jiang,Chi-Min Shu
Styrene polymerization is highly vulnerable to thermal runaway because of its strong exothermicity, viscosity increase, and deterioration of heat transfer during reaction. The thermal hazards of tert-butyl peroxybenzoate (TBPB) and TBPB-initiated styrene polymerization were investigated by differential scanning calorimetry (DSC), accelerating rate calorimetry (ARC), kinetic analysis, and Thermal Safety Software (TSS). The effects of TBPB dosage on runaway triggering, acceleration, and storage safety were evaluated using styrene/TBPB systems with mass ratios of 100:1, 100:2, and 100:10. Results showed that the addition of TBPB significantly increased the triggering sensitivity of styrene polymerization. Under adiabatic conditions, the exothermic onset temperature decreased from 105 °C for pure styrene to 75 °C for all TBPB-initiated systems. With increasing TBPB dosage, the time to maximum rate under adiabatic conditions (TMRad) decreased markedly, indicating a shorter intervention window during runaway development. Although the total heat release of the initiated systems changed only slightly, the high-dosage system exhibited more complex exothermic behavior, suggesting stronger coupling between initiator decomposition and styrene polymerization. TSS simulation further indicated that overheating could lead to severe runaway risk during storage and transportation. These results show that TBPB mainly reduces the thermal safety margin of styrene polymerization by lowering the runaway onset temperature and accelerating the runaway process.
✓ 已验证
DOI
高影响因子
ACS Energy Letters
·
2026
·
IF 17.5
Jianhong Wu,Dongmin Qian,Xiuqin Yan,Yuxiao Cai,Fuyi Zhou,Yangyang Guo,Wei Zhu,Weiwei Lu,Ruishan Wang,Ziheng Zhou,Chao Ma,Yonghua Chen,Nana Wang,Yu Cao,Jianpu Wang
Perovskite light-emitting diodes (LEDs) are sensitive to the quality of the perovskite films, which typically require fabrication in inert atmospheres to avoid moisture-induced uncontrolled crystallization, thereby increasing manufacturing complexity and cost. Here, it is demonstrated that cesium iodide and zinc acetate suppress the formation of lead polyhalide intermediates and enable the rapid growth of three-dimensional perovskite in ambient air. This approach suppresses water-induced uncontrolled growth, leading to the formation of perovskite films with uniformly distributed grains and reduced trap density. With this approach, ambient-air-processed near-infrared perovskite LEDs with a peak external quantum efficiency of 20.2% and enhanced stability are demonstrated.
✓ 已验证
产品关联
DOI
高影响因子