COMPOSITES PART B-ENGINEERING
·
2026
·
IF 14
Lichaoran Guan,Kan Liu,Yishi Su,Yiwei Dong,Mingyu Li,He Cao,Andong Hua,Qiubao Ouyang,Di Zhang
Aluminum matrix composites (AMCs) reinforced with high-content nanoparticles offer great potential for breaking modulus-strength-ductility trade-off, yet still face the challenge of spontaneous agglomeration and insufficient strain hardening in ultrafine-grained (UFG) matrices. This work presents a novel strategy that spatially arranges high-content (15 wt%) SiC nanoparticles (SiCnps) to construct a heterogeneous grain structure within 2024Al. The synergistic architecture SiCnp/2024Al composites realized significantly enhanced mechanical properties over the 2024Al matrix, with yield strength and Young's modulus increasing by 49.8% and 31.9%, respectively, while maintaining elongation of >7%. The well-balanced strength-ductility is attributed to the microstructural responses during straining. Initially, hetero-grained interfaces drive the rapid multiplication of geometrically necessary dislocations (GNDs) in fine-grained (FG) zones. Subsequently, dislocation accumulation is enhanced by high-content SiCnps with associated lattice defects (stacking fault, Lomer-Cottrell lock and 9R structure) in UFGs at the later plastic stage. Such an innovative “relay race-hardening” mechanism, orchestrated by the cross-scale hetero-structures, gives rise to a distinctive three-stage strain hardening behavior. Notably, such behavior is not observed in AMCs with 2% SiCnps. Quantitative analysis of dislocation dynamic signals further elucidates the underlying deformation mediated mechanisms. This work thus provides a new pathway for designing high-content nanoparticle-reinforced AMCs.
✓ 已验证
DOI
高影响因子
CHEMICAL ENGINEERING JOURNAL
·
2026
·
IF 12.5
Yu Long,Tao Wang,Yan Wang,Xiaolong Huang,Zhongyan Gong,Zhiyuan Ma,Yu Lei,Biwei Deng,Yan Li
PUA oligomers with different molecular weights enable 3-order modulus tunability. • Near-ambient T g promotes segmental mobility for high toughness. • Solvent-free photoresists allow high-fidelity TPP printing of complex structures. • Micro-pillars sustain 54% measured strain with recovery rates up to 85%. • Robust architectures maintain integrity under 60% set strain without failure. Two-photon polymerization (TPP) has attracted increasing attention and research interest due to its high-resolution fabrication capability at the micro/nanoscale. While rigid photocurable monomers are often used to enhance mechanical performance, they can lead to modulus mismatch that limits applicability in flexible devices. In this work, a series of polyurethane acrylate (PUA) oligomers with different molecular weights are synthesized, enabling the tuning of storage modulus (25 °C) across three orders of magnitude. These oligomers form the basis of a solvent-free elastomeric photoresist (G-PCLx), suitable for photoresist-immersion printing (i.e., the objective lens is directly immersed in the photoresist droplet). In situ compression tests reveal that micro-pillars fabricated from the G-PCL1000 exhibit exceptional damage tolerance, sustaining 54% measured strain without structural collapse and achieving recovery rates up to 85%. Complex architectures, such as fullerene spheres and Kelvin lattices, maintain structural integrity under 60% set strain, developing only minor cracks (1–1.5 um length) without structural failure. The achieved mechanical robustness originates from the glass transition temperature of the PUA oligomer near room temperature (~25 °C), which promotes segmental mobility within the crosslinked network. This design provides an effective strategy for fabricating high-precision, flexible microstructures at room temperature. Download: Download high-res image (106KB) Download: Download full-size image
✓ 已验证
DOI
高影响因子
Nano Energy
·
2026
·
IF 16.7
Yingying Li,Xianchun Jin,Lili Xing,Xinyu Xue
Development of a droplet-driven self-powered catalytic system based on a UiO-66 integrated composite film. • Integration of energy harvesting and electrocatalysis via a superhydrophobic interface for efficient charge generation. • In situ generation of ROS (H₂O₂, ·OH, ·O₂⁻) boosts degradation of organic pollutants. • Stable operation and superior catalysis over conventional adsorption systems, enabling decentralized wastewater treatment. Efficient degradation of organic pollutants in wastewater is crucial for environmental protection, yet the development of low-energy or even energy-free treatment technologies remains highly desirable. With the increasing pollution load driven by economic growth, conventional centralized wastewater treatment processes suffer from high energy consumption and limited applicability, making them unsuitable for decentralized and in-situ applications. Therefore, developing low-energy treatment strategies that can operate in natural environments is of great importance. Here, a droplet-driven self-powered system for organic pollutant degradation is proposed. Falling wastewater droplets interact with UiO-66 (University of Oslo-66)-based composites supported on carbon felt (Al-PTFE-UiO-66@CF), converting mechanical energy into electricity and triggering in-situ electrochemical reactions. Electron transfer at the superhydrophobic PTFE solid-liquid interface activates dissolved oxygen. Reactive oxygen species, including hydrogen peroxide (H 2 O 2 ), hydroxyl radicals (·OH), and superoxide radicals (·O 2 - ), are generated in the presence of UiO-66 and enable synergistic degradation of organic pollutants. After eight cycles, the system achieves degradation efficiencies of 90%, 83%, and 80% for rhodamine B, crystal violet, and methyl orange, respectively. The droplet-induced interfacial electrochemical process enhances electron transfer and promotes the generation of strong oxidative radicals, leading to significantly improved degradation rates. Overall, this work presents a nearly zero-energy self-powered wastewater treatment strategy and offers a promising solution for efficient water purification in areas without electricity and decentralized systems. Download: Download high-res image (203KB) Download: Download full-size image We present a droplet-driven self-powered catalytic system based on a UiO-66 integrated composite film. The superhydrophobic interface enhances interfacial charge generation under droplet impact, enabling efficient conversion of droplet kinetic energy into electrical energy. The generated electrons activate dissolved oxygen to produce reactive oxygen species, including H 2 O 2 , ·OH, and ·O 2 - , which drive the degradation of organic pollutants. The system exhibits stable operation and improved catalytic performance, offering a new strategy for decentralized wastewater treatment and environmental remediation.
✓ 已验证
DOI
高影响因子
JOURNAL OF CONTROLLED RELEASE
·
2026
·
IF 12.4
Xi Zhang,Wenting Yu,Zilong Chen,Ting Li,Shimin Zong,Jinghang Li,Hongjun Xiao,Lesan Yan
Cisplatin is a first-line chemotherapeutic agent for solid and metastatic tumors, yet its ototoxicity remains a major clinical challenge, causing irreversible, bilateral, dose-dependent sensorineural hearing loss. This toxicity severely impairs patients' quality of life and, in children, disrupts language and socio-cognitive development. Conventional strategies using antioxidants, anti-inflammatory agents, or molecular inhibitors only partially mitigate ototoxicity, while systemic administration compromises cisplatin's antitumor efficacy. Intratympanic delivery reduces systemic interference, but small-molecule drugs suffer from poor solubility, low stability, and short half-lives, necessitating frequent dosing that increases risks of local trauma and infection. Advanced biomaterial-based delivery systems provide promising solutions by protecting therapeutics, enhancing local bioavailability, and minimizing systemic toxicity. Poly(amino acid)s are attractive carriers due to their biocompatibility, biodegradability, and tunable side chains. Here, we developed amphiphilic poly(amino acid)s with intrinsic antioxidant activity and engineered nanoprodrugs via covalent conjugation with antioxidant drugs. Administered intratympanically, these self-assembled micelles exhibited prolonged cochlear retention. Mechanistically, the nanoprodrugs alleviated ototoxicity by reducing intracellular cisplatin accumulation through drug chelation and simultaneously scavenging cisplatin-induced reactive oxygen species within cells. This “dual-function” action significantly preserved hearing, providing both mechanistic insight and a potential therapeutic strategy for cisplatin-induced ototoxicity and other hearing impairments.
✓ 已验证
DOI
PubMed
高影响因子
CERAMICS INTERNATIONAL
·
2026
·
IF 6
Yuan-Bin Chen,Xiuyuan Su,Ruxuan Tang,Ling Tang
Building upon the Ln 2 Zr 3 (MoO 4 ) 9 (Ln = La, Pr, Sm, Eu, Gd) molybdate system, this study strategically employs (Bi 0.5 Ta 0.5 ) 4+ co-substitution at Zr 4+ sites to achieve a enhancement in quality factor ( Q×f ), concurrently reducing optimal sintering temperatures for La- (725 °C) and Sm-based (725 °C) systems compared to their pristine counterparts. Comprehensive structural characterization through X-ray diffraction, Raman spectroscopy, and electron microscopy confirms the formation of phase-pure solid solutions with enhanced densification (relative density >95%), while bond valence analysis reveals that Ln-O bonds predominantly govern ionic characteristics ( f i >78%), whereas Mo-O interactions critically determine lattice energy and thermal expansion coefficients. The engineered Ln 2 [Zr 0.89 (Bi/Ta) 0.11 ] 3 (MoO 4 ) 9 ceramics exhibit microwave dielectric properties tailored by lanthanide ionic radii: La-system demonstrates εᵣ = 10.97,Q×f = 135,333 GHz,τf = −29.74 ppm/°C; Sm-system achieves εᵣ = 11.46, Q×f = 157,465 GHz, τf = -30.96 ppm/°C; Gd-system yields εᵣ = 11.63, Q×f = 157,280 GHz, τf = −30.60 ppm/°C.Notably, sintering temperature reduction is particularly pronounced in Eu-system (675 °C, εᵣ = 11.49, Q×f = 87,850 GHz, τf = −35.59 ppm/°C), attributed to the synergistic effects of bond polarizability enhancement and lattice energy optimization. These results establish a universal ion-substitution paradigm for developing advanced ULTCC materials with simultaneously improved Q×f and reduced processing temperatures (<725 °C), demonstrating significant potential for millimeter-wave communication applications. Through ion substitution, these materials all have low sintering temperatures and high Q×f values, making them ideal candidates for low-temperature co-fired ceramics (LTCC).
✓ 已验证
DOI
高影响因子
JOURNAL OF HAZARDOUS MATERIALS
·
2026
·
IF 10.6
Huijun Li,Xiaodie Zheng,Honghong Shan,Yichao Huang,Chuanxin Ma,Jian Zhao,Xiaochen Huang
Microplastics (MPs) derived from film mulching commonly exist in cadmium (Cd)-contaminated agricultural soil, but their impacts on Cd phytotoxicity are still controversial. Lipid remodeling is a key plant stress response, but whether conventional and biodegradable MPs differently regulate this process under Cd stress remain unclear. This study compared the effects of conventional polyethylene (PE) and biodegradable polylactic acid (PLA) MPs at two concentrations (0.1% and 1%) on Cd phytotoxicity in maize via a 35-day pot experiment, mainly focusing on the lipid homeostasis. Both individual and combined exposures to MPs and Cd inhibited maize growth and photosynthesis and induced oxidative stress. PE significantly reduced Cd concentration (20.06–38.71%) and uptake content (27.22–39.77%) in shoots and roots. PLA exhibited dose-dependent effects, where 0.1% addition increased Cd accumulation in roots, while 1% addition decreased it in shoots. These effects might be attributed to altered homeostasis of essential minerals (Ca, Fe, and Cu). Interaction analysis revealed that PE acted antagonistically with Cd at 0.1% and synergistically at 1%, while PLA showed antagonism at both concentrations. Integrated lipidomic and transcriptomic analyses identified five key regulatory genes ( LACS4 , GPAT6 , LPP2 , PLA2-III , and LPCAT4 ) significantly associated with 36 glycerophospholipids and glycerolipids, revealing that PE and PLA influenced maize molecular response via distinct lipid metabolism pathways under Cd stress. These findings demonstrate that conventional and biodegradable MPs differentially regulate Cd phytotoxicity in Cd‑contaminated soils through lipid remodeling, providing new insights for the safety assessment of agricultural film mulching.
✓ 已验证
DOI
PubMed
高影响因子
Nano Energy
·
2026
·
IF 16.7
Gang Yu,Lei Liu,Xinlei Cai,Wenlong Cheng,Dongdong Zhou,Chun Li,Chenxing Yang,Jun Wu,Yan Shi,Kedong Bi
Reveals the "pressure-triggered deformable capacitance" mechanism in LM-TENGs. • Achieves a high power density of 33.98 W/m² with 28-fold voltage enhancement. • Develops a 270-mg origami TENG that instantly powers 100 LEDs. • Enables self-powered sensing through physically decoupled electrode design. Liquid metal nanodroplets (LMND) offer exceptional potential for enhancing triboelectric nanogenerators (TENG) due to their intrinsic fluidity and high electrical conductivity, yet the underlying mechanism governing their performance enhancement remains elusive. Here, we propose a "pressure-induced deformation capacitance" mechanism, achieved by uniformly confining LMND within thermoplastic polyurethane (TPU) nanofibers. Under external pressure, the flexible TPU matrix induces controlled deformation of embedded LMND while effectively preventing their leakage, forming a dynamically optimized micro-capacitance network that significantly enhances charge storage capacity. Atomic force microscopy mechanical mapping confirms this effect is exclusive to low Young's modulus matrices. Electrical characterization revealed that the size dependence is not monotonic. Both the capacitive sensitivity of the composite and the TENG output follow a Lorentzian distribution, with the peak occurring when the ratio of the LMND size to the TPU fiber diameter reaches 120%. The optimized TENG exhibits a 28-fold voltage enhancement and a power density of 33.98 W/m². We further develop an origami-structured TENG (270 mg) capable of powering 100 LEDs and demonstrate a self-powered sensing system via functionally decoupled electrode design. This work establishes fundamental design principles for high-performance flexible energy devices and provides a framework for their application in advanced human–machine interfaces. Download: Download high-res image (208KB) Download: Download full-size image
✓ 已验证
DOI
高影响因子
Food Chemistry-X
·
2026
·
IF 9.2
Xianliu Chen,Yanling Zhang,Qiong Wu,Lvyun Zhuang,Zhonghua Yang,Qun Zhang,Lehe Tan,Weijie Lan,Mingyue Wang,Chen Ma,Zhi Xu,Daizhu Lyu
Imazalil (IMZ) is the most widely used postharvest fungicide during banana storage and transport, yet its potential impact on banana quality remains largely unknown. In this study, integrated volatilomics, targeted lipidomics, and untargeted metabolomics were applied to investigate how different enantiomers of IMZ affect aroma in the postharvest banana yellow ripening stage. Results showed that Rac-IMZ and R-(−)-IMZ disrupted fatty acid and branched-chain amino acid metabolism, significantly lowering precursor pools of linoleic acid, α-linolenic acid, leucine, and valine required for ester formation via the lipoxygenase and amino acid pathways. S-(+)-IMZ exhibited minimal interference with these pathways, thereby maintaining aroma quality comparable to untreated fruit. These findings highlight an impact associated with the use of racemic imazalil in banana postharvest preservation and provide multi-omics evidence that replacing the racemate with the single S-(+)-enantiomer can achieve effective postharvest disease control while largely preserving the characteristic aroma of banana.
✓ 已验证
DOI
PubMed
高影响因子
CHEMICAL ENGINEERING JOURNAL
·
2026
·
IF 12.5
Fanghua Liu,Chizhong Wang,Wen Guo,Kaiyang Pan,Lei Qiu,Xiaolin Ma,Sizhe Chen,Jiawei Li,Junhua Li,Huazhen Chang
A new catalyst design balances key steps in oxygen evolution. • Structural distortions create complementary active reaction sites. • This cooperation stabilizes essential intermediates for oxygen bonding. • The improved catalyst achieves efficient oxygen evolution activity. The oxygen evolution reaction (OER) is critical to the electrochemical conversion of sustainable energy, as its efficiency depends on the balanced adsorption strengths of multiple reaction intermediates (*O, *OH, *OOH) during O−O bond formation. Here, we demonstrate that inverse Jahn-Teller (J-T) distortions between adjacent metal sites can dynamically modulate the adsorption of these intermediates, offering a general strategy to optimize multi-step electrocatalytic processes. By fabricating a phosphate-mediated CoFe (oxy)hydroxide catalyst, we induce a strong J-T effect with axial elongation of the CoO 6 octahedra and axial compression of the FeO 6 octahedra, thereby creating complementary active sites. X-ray absorption spectroscopy and theoretical calculations reveal that the compressed FeO 6 octahedra promoted the formation of high-valent Fe-oxo, while the elongated Co–OH exhibit greater nucleophilicity, facilitating proton transfer to stabilize *OOH intermediates at neighboring Fe sites. This cooperative effect lowers the energy barrier for O−O coupling. As a result, the CoFePi achieves a remarkably low Tafel slope of 32 mV dec −1 . Download: Download high-res image (161KB) Download: Download full-size image
✓ 已验证
DOI
高影响因子
MATERIALS SCIENCE IN SEMICONDUCTOR PROCESSING
·
2026
·
IF 5.2
Guoqiang Zhang,Hao Hu,Jianping Yang,Junfeng Chen,Jiaxuan Hao,Ping Lin,Tiantian Liu,Lingbo Xu,Peng Wang,Xiaoping Wu,Can Cui
Perovskite photodetectors have attracted considerable attention due to their excellent optoelectronic properties and low-cost solution processability. However, the practical application of formamidinium lead iodide (CH(NH 2 ) 2 PbI 3 , FAPbI 3 ) based devices is severely hindered by high defect densities, phase instability, and non-radiative recombination losses. Herein, we demonstrate a simple and effective strategy to simultaneously address these challenges by incorporating polyethylene glycol (PEG) as a multifunctional additive into the FAPbI 3 precursor solution. Systematic optimization reveals that an optimal PEG concentration (2 mg/mL) significantly improves film crystallinity, enlarges grain size and reduces trap density, as evidenced by XRD, SEM, and SCLC analyses. The synergistic interaction mechanism was investigated by combining XPS and FTIR spectroscopy. Consequently, the optimized PEG-2 photodetector exhibits a ∼30% reduction in dark current, a ∼750% enhancement in photocurrent, and a ∼13-fold increase in on/off ratio compared to the pristine device. Both responsivity and detectivity are substantially improved across the visible spectrum, achieving a responsivity of 3.8 mA/W and a specific detectivity of 9.76 × 10 10 Jones. This work establishes PEG as a low-cost, multifunctional additive for defect passivation and morphology control in FAPbI 3 perovskites, offering a simple strategy toward high-performance, stable photodetectors and molecular guidance for rational polymer design.
✓ 已验证
DOI
高影响因子
CERAMICS INTERNATIONAL
·
2026
·
IF 6
Xuchen Duan,Xiao Yang,Linghao Wu,Hua Wang,Bing Ai,Shichao Zhang,Haoran Sun,Xiankai Sun,Sai Li,Yuchen Cao
To address the weak infrared extinction capability of silica aerogel composites at high temperatures, this study introduces an yttria-stabilized zirconia (YSZ) fibrous membrane fabricated by electrospinning to suppress infrared radiation. This strategy effectively overcomes the limitation of weak infrared extinction at elevated temperatures and enhances the thermal insulation performance of the silica aerogel composites. After heat treatment at 900 °C, the as-prepared YSZ fibrous membrane exhibits a tetragonal crystalline phase, an average fiber diameter of 880 nm, and an infrared reflectance of 58%. By Incorporating three layers of the YSZ fibrous membrane into the silica aerogel composite, a thermal conductivity of 0.082 W/(m·K) is achieved at 1000 °C, corresponding to a 20.38% improvement in thermal insulation performance. The YSZ fibrous membrane effectively suppresses radiative heat transfer within the material, demonstrating great potential for practical applications.
✓ 已验证
DOI
高影响因子
ChemistrySelect
·
2026
·Vol. 11
·期 20
·e73535
·
IF 2.3
Wei Liu,Nannan Wang,Zhangyu Dai,Yanhua Sun,Qiongyao Zeng
This article is based on Zn-MOF-8 and uses a simple thermal synthesis method to prepare nitrogen-doped mesoporous carbon spheres (NMC), which is then combined with Ti 3 C 2 to prepare NMC/Ti 3 C 2 nanocomposites. It was characterized by SEM, EDS, XPS, FTIR, and electrochemical methods. The NMC/Ti 3 C 2 nanocomposite modified glassy carbon electrode (GCE) was used for sensitive detection of isoquercetin (IQ), achieving a wide linear range of 0.1–100 µM and a low detection limit of 0.073 µM (S/N = 3). The modified electrode also exhibits good selectivity, excellent anti-interference performance and can be used for actual sample detection. Graphical Nitrogen-doped mesoporous carbon spheres (NMC) were prepared using a simple thermal synthesis method with Zn-MOF-8 as a precursor. Subsequently, NMC was combined with Ti 3 C 2 to prepare NMC/Ti 3 C 2 nanocomposites. The NMC/Ti 3 C 2 nanocomposites were characterized using SEM, EDS, XPS, FTIR, and electrochemical methods. The NMC/Ti 3 C 2 nanocomposites were used to modify glass carbon electrodes (GCE), resulting in NMC/Ti 3 C 2 /GCE, which was employed for the sensitive detection of quercetin (IQ), achieving a wide linear range of 0.1–100 µM and a low detection limit of 0.073 µM (signal-to-noise ratio S/N = 3). The modified electrode also exhibited good selectivity and excellent anti-interference capability, making it suitable for detecting real samples.
✓ 已验证
DOI
高影响因子