JOURNAL OF CHEMICAL THERMODYNAMICS
·
2020
·
IF 2.888
Shihua Dong,Weizhen Sun,Yueyang Jiang,Bing Jia
Liquid-liquid equilibrium (LLE) data for {water + furfuryl alcohol + solvent (isopropyl ether, tert-butyl methyl ether, dichloromethane and methyl isobutylcarbinol)} ternary systems were determined at T = 298.2 K and p = 101.3 kPa. The distribution coefficients and separation factors were evaluated and the results showed that those solvents can effectively for furfuryl alcohol recovery from aqueous solutions. The Othmer-Tobias, Bachman and Hand equations were employed to validate the reliability of the experimental LLE data. Additionally, the experimental LLE data were correlated using the NRTL and UNIQUAC models and the binary interaction parameters were optimized. The root mean square deviations (RMSD) between the correlated data by NRTL and UNIQUAC models and the experimental LLE data were less than 0.36%, which demonstrated that both models can correlate experimental LLE data successfully.
研究领域:
化学工程
·
热力学
✓ 已验证
DOI
高影响因子
Journal of Energy Storage
·
2023
·
IF 9.4
Yao Lu,Miaoyan Song,Jieyou Huang,Le Zhang,Binyu Zhao,Wenwei Wu,Xuehang Wu
Charging P2-type Na 0.66 Ni 0.33 Mn 0.67 O 2 (NNM) to a high upper cut-off voltage of 4.3 V (vs. Na + /Na) can yield a competitive discharge voltage (3.6 V-class) and capacity. However, achieving stable cycling for NNM under this condition remains challenging owing to an unfavorable phase transition and a large lattice-volume change. Herein, a dual-site doping strategy is used to simultaneously realize a pinning effect at the Na and transition metal sites. Incorporating pinned K + and Zn 2+ ions considerably enhances the structural stability of NNM, affording a complete single-phase reaction with ultralow strain (only 0.54 % variation in volume) during Na + insertion/extraction. The synergistic contributions of dual-site doping to the enhanced electronic conductivity , lowered Na + migration barrier, and increased Na + diffusion coefficients are confirmed via theoretical calculations. Consequently, the K + /Zn 2+ dual-site-doped Na 0.63 K 0.03 Ni 0.26 Zn 0.07 Mn 0.67 O 2 delivers satisfactory discharge capacities of 118.6 and 63.2 mAh g −1 at 10 and 2000 mA g −1 , respectively, and achieves an excellent capacity retention of 81.2 % after 200 cycles at 500 mA g −1 . This study provides a promising method to strengthen the stability of the Ni − Mn-based layered framework and optimize other high-voltage and high-capacity layered oxide cathode materials .
研究领域:
材料科学
·
电化学
·
储能技术
·
电池技术
·
无机化学
✓ 已验证
DOI
高影响因子
JOURNAL OF LUMINESCENCE
·
2023
·
IF 3.6
Mingsheng Cai,Tianchun Lang,Shuangqiang Fang,Tao Han,Damir Valiev,Houjiang You,Chong Liu,Jing Yu,Peng Su,Xiaolong Jing,Guanghui Ge,Bitao Liu,Elena F. Polisadova
Fluorescent materials are widely used for anti-counterfeiting of information security and commodities. However, the increasing requirements for fluorescent anti-counterfeiting technology urgently require the development of novel fluorescent materials with multicolor fluorescence, single component, and excellent stability. Herein, a color tunable Ba 0·94 Ca 0.06 ScO 2 F: Eu 2+ , Bi 3+ , K + perovskite with dependence of excitation wavelength for high-level anti-counterfeiting is reported. The fluorescence spectra of Ba 0·94 Ca 0.06 ScO 2 F: Eu 2+ , Bi 3+ , K + perovskite show the tunable emission band with the peak between 479 and 509 nm. It is worth noting that the peak intensity ratio at 479 and 509 nm changes with the dependence of the excitation wavelength. Meanwhile, the snowflake pattern is designed to demonstrate the potential applications in anti-counterfeiting, which obviously shows four different color patterns under the sunlight, 320 360, and 415 nm excitation, respectively.
研究领域:
材料科学
·
光学材料
·
防伪技术
·
发光学
·
光子学
✓ 已验证
DOI
高影响因子
Journal of Materials Chemistry C
·
2017
·Vol. 5
·期 37
·9545-9551
·
IF 5.256
Jian-Min Li,Jie Fang
An anthracene vapor-assisted inverse transport growth mechanism of unsupported ultrathin two-dimensional (2D) superconducting single-crystal niobium (Nb) and niobium diselenide (NbSe2) nanoplates (thickness ∼2.5 nm) using anthracene and NbSe2 powders as precursors is reported. Besides the whisker-like counterparts, the anthracene vapor hierarchical invasion into NbSe2 leads to 2D Nb nanoplates with a {110} surface and 2D few-layered {0001} NbSe2 nanoplates grown in the high-temperature residual region, while sub-millimeter selenium whiskers are found in the low-temperature transporting region. Direct magnetization measurements demonstrated that superconductivity at ∼3.3 K was clearly observed in the unsupported ultrathin Nb and NbSe2 nanoplates. These findings may offer a new way to produce freestanding single-crystal 2D superconductors and elemental 2D metallic nanoplates.
研究领域:
材料科学
·
凝聚态物理
·
纳米技术
·
超导物理
·
二维材料
✓ 已验证
DOI
高影响因子
Journal of Materials Chemistry A
·
2016
·Vol. 4
·期 43
·17104-17110
·
IF 8.262
Wenzhe Li,Jiangwei Li,Jiaoli Li,Jiandong Fan,Yaohua Mai,Liduo Wang
The poor stability of hybrid organic–inorganic perovskite is one of crucial problems limiting the practical application of the perovskite solar cells (PSCs). All-inorganic lead-free perovskite materials, with Cs replacing the organic cations and Sn replacing Pb, have shown great potential in achieving high thermal stability. However, tin-based perovskites have inevitably suffered from severe bulk recombination, attributed to Sn vacancies. In this work, we obtain CsSnIBr2 thin films with low Sn vacancy assisted by the addition of hypophosphorous acid (HPA). The HPA additive here as complexant is demonstrated to be capable of speeding up the nucleation process while inhibiting the formation of Sn4+ during the formation process of CsSnIBr2 thin films. With a mesoscopic architecture, the CsSnIBr2 PSCs exhibit efficiency-loss free in 77 days and remarkably stable power output within 9 hours at high temperatures up to 473 K.
研究领域:
材料科学
·
光伏技术
·
无机化学
·
能源材料
✓ 已验证
DOI
高影响因子
JOURNAL OF ALLOYS AND COMPOUNDS
·
2021
·
IF 5.316
Jin Chen,Chun-Li Hu,Yi-Lin Li,Qian-Qian Chen,Bing-Xuan Li,Jiang-Gao Mao
Herein, we reported two alkali metal molybdenum(VI) iodates, namely, NaMoO 3 (IO 3 ) and γ-KMoO 3 (IO 3 ) with 1D and 3D [MoO 3 (IO 3 )] − anionic architectures, respectively. The novel 1D chain in NaMoO 3 (IO 3 ) and the 3D network in γ-KMoO 3 (IO 3 ) are constructed by the 0D Λ-shaped cis -[MoO 4 (IO 3 ) 2 ] 4− building units interconnected by bridging IO 3 − anions as well as the corner-sharing of oxo anions. Importantly, the polar γ-KMoO 3 (IO 3 ) exhibits a very large second-harmonic generation (SHG) effect of 12 × KH 2 PO 4 (KDP) under 1064 nm laser radiation, a high laser-Induced damage threshold value (52 × AgGaS 2 ), and a moderate birefringence of 0.087@1064 nm, whereas the centrosymmetric NaMoO 3 (IO 3 ) has a large birefringence of 0.208@1064 nm. This study further proves the useful route of exploring promising optical materials via assembling the 0D basic building units into higher dimensional anionic architectures.
研究领域:
无机化学
·
材料科学
·
光学
✓ 已验证
DOI
高影响因子
JOURNAL OF CHEMICAL AND ENGINEERING DATA
·
2021
·
IF 2.694
Shaonan Zhang,Ningning Tian,Shengzhe Jia,Jing Yang,Yu Zhou,Shichao Du,Zhenguo Gao
The solubility of pentaerythritol (PE) in four binary solvents (methanol + water, ethanol + water, isopropanol + water, acetonitrile + water) is determined using the gravimetric method at temperatures ranging from 283.15 to 323.15 K under 0.1 MPa. The experimental results demonstrate that the solubility of PE increases with the increase of temperature in all four binary solvent systems. And water has a relatively positive effect on the solubility of PE in all four binary solvents. However, the solubility of PE in ethanol + water and isopropanol + water mixtures first increases with the increase of the ethanol/isopropanol fraction and then decreases when the temperature exceeds 303.15 and 288.15 K, respectively. And the solubility reaches the maximum when the initial mole fractions of ethanol/isopropanol of the binary solvent are 0.2. Besides, experimental solubility is fitted with three thermodynamic models including the modified Apelblat model, λh model, and CNIBS/R-K model, and all of the average relative deviation (ARDs) are less than 4%, indicating good accordance with the experimental results. In addition, among the three thermodynamic models, the CNIBS/R-K model has the best fitting performance, in which all of the ARDs are less than 1.7%.
研究领域:
化学工程
·
物理化学
✓ 已验证
DOI
高影响因子
JOURNAL OF CHEMICAL THERMODYNAMICS
·
2020
·
IF 2.888
Lele Chen,Xiuxiu Yang,Yafei Guo,Tianlong Deng,Dan Li,Lingzong Meng
The solubility corresponding solution physicochemical properties (densities, refractive indices and pH) in the quaternary system (NaCl + NaBO 2 + Na 2 B 4 O 7 + H 2 O) were investigated at 298.15 K by the isothermal dissolution equilibrium method. The dry-salt phase diagram, water content diagram, refractive index diagram and pH diagram were drawn. There are four crystallization fields corresponding to NaCl, NaBO 2 ·4H 2 O, Na 2 B 4 O 7 ·10H 2 O, NaCl·NaBO 2 ·2H 2 O, five univariant curves and two invariant points in the phase diagram of the quaternary system. The solubility, concentrations of boron species B(OH) 3 , B(OH) 4 − , B 3 O 3 (OH) 4 − , B 4 O 5 (OH) 4 2− and OH − in the system were calculated using the Pitzer model. The variation trends for calculated solubility curves and pH curves are consistent with the experimental results. The distributions of different boron species were obtained in the mixed borate solution. The distributions of four boron species were obtained in the mixed borate solution. The main boron species in the mixed borate solution are B(OH) 4 − and B 4 O 5 (OH) 4 2− . The mole fractions of the four boron species are mainly affected by m (B) in the solution but less by m (Cl − ).
研究领域:
化学热力学
·
无机化学
✓ 已验证
DOI
高影响因子
JOURNAL OF CHEMICAL AND ENGINEERING DATA
·
2020
·
IF 2.369
Hongxia Li,Lijiang Guo
The solubility and phase diagram of the CsCl–MgCl2–H2O ternary system, at a relatively wide temperature range, are significantly important for the extraction of the cesium resources from salt lakes. The isothermal dissolve equilibrium (IDE) method was used to determine the solubility of this ternary system at T = 273.15, 308.15, and 348.15 K, which have not been reported yet. The measured results indicated that the equilibrium solid phases in this ternary system from T = 273.15 to 348.15 K are CsCl, double salt CsCl·MgCl2·6H2O, and MgCl2·6H2O, and correspondingly there are three crystal regions and two cosaturated points for these solid phases. The solubility of the salt increased with the increase of the temperature, and the double salt CsCl·MgCl2·6H2O and CsCl crystal regions also became larger with the increasing temperature. However, the crystal regions of the MgCl2·6H2O solid phase are not enlarged obviously. Based on the solubility and phase diagram of CsCl–MgCl2–H2O at different temperatures, the separation process of CsCl resources has been proposed.
研究领域:
化学
·
材料科学
✓ 已验证
DOI
高影响因子
JOURNAL OF SOLUTION CHEMISTRY
·
2025
·Vol. 55
·期 3
·366-381
·
IF 1.3
Zhou Jinpeng,Du Yanping,Xie Peijing,Liu Bin,Xue Ning,Hou Haiyun,Wang Ning,Zheng Lina
The thermodynamic properties of electrolyte solutions elucidate the mechanisms of ionic interactions in solution. This study investigates the thermodynamic properties of the ternary systems containing cesium bromide (CsBr), water, and either 1,2-butanediol (1,2-BDO) or 1,4-butanediol (1,4-BDO) at 298.2 K utilizing potentiometric techniques. CsBr molalities were in the approximate range of 0.01 to 1 mol·kg −1 , and the mass fraction of 1,2-BDO/1,4-BDO in 1,2-BDO/1,4-BDO+H 2 O binary mixed solvents were 0, 0.10, 0.20, and 0.30. The Debye-Hückel model, the Pitzer model, along with the Nernst equation were explored to determine the thermodynamic parameters, which included the mean ionic activity coefficients ( γ ± ), osmotic coefficients ( φ ), excess Gibbs free energy ( G E ), standard Gibbs free energy of transference (Δ G
0 t
), and primary hydration number ( n hydr ). The results reveal that the γ ± of CsBr decreases with increasing the molality of CsBr and with increasing the mass fraction of 1,2-BDO and 1,4-BDO in the binary mixture. A positive value for the Δ G
0 t
signifies that the transfer of CsBr from pure water to the mixed solvent system is thermodynamically unfavorable and thus non-spontaneous. These findings can provide thermodynamic data to support potential industrial processes.
✓ 已验证
DOI
高影响因子
ACS Applied Nano Materials
·
2026
·Vol. 9
·期 33
·15886-15898
·
IF 5.8
Qi Yexiong,Zhao Zimeng,Chen Li,Li Tingting,Lin Ligang,Zhou Zena,Zheng Yong
The all-textile piezoelectric sensor,
capable of achieving
high-sensitivity
pressure sensing while meeting the requirements of wearability, comfort,
and structural flexibility, holds great significance for intelligent
wearable motion monitoring. In this study, MXene was employed to induce
the transition of polyacrylonitrile (PAN) molecular chains from a
3 1 helical conformation to a planar zigzag conformation,
which significantly enhanced the piezoelectric output performance.
Under an impulse force of 7 N at 1 Hz, the sensor exhibited an output
voltage of 34.1 V, with a sensitivity of 1.51 V/N over the range of
1–9 N. The silver-based knitted fabric electrode (silver-knitted
fabric) was knitted on a computerized flat-knitting machine, fully
leveraging the advantages of the knitted electrode, including high
conductivity (resistance of only 4.2 Ω), high air permeability
(1235 mm/s), and excellent structural flexibility. The electrospun
MXene/PAN/K-BTO composite nanofiber membrane was subsequently integrated
with the silver-based knitted fabric electrode to construct an all-textile
flexible piezoelectric sensor with a three-layer sandwich structure.
After 2000 consecutive impact cycles, the sensor output signal remained
stable without any attenuation. The sensor accurately identified various
human motion patterns, including finger bending (approximately 0.08
V), elbow flexion and extension, and walking gait (approximately 18.1
V). Owing to its excellent skin adherence and high sensitivity to
subtle movements, this sensor provides an effective monitoring tool
for intensive care and consciousness recovery assessment. Furthermore,
it holds promising potential for applications in sports health monitoring
and human–computer interaction, offering solutions for next-generation
embodied intelligence and personalized health monitoring systems.
✓ 已验证
产品关联
DOI
高影响因子
JOURNAL OF POWER SOURCES
·
2025
·
IF 7.9
Yongyi Li,Wei Li,Zhigang Shao,Huiyang Xu,Shuanglong Li,Bo Wang,Xiaorui Huang,Shichao Jiao,Zhiwei Li
Photocatalytic production of hydrogen peroxide from water is regarded as an environmentally benign technology for energy storage and supply. Herein, a disordered K&Na-C 3 N 5 photocatalyst co-intercalated with K + &Na + and modified by cyano/hydroxyl groups is successfully fabricated via alkali-activated thermal-polymerization. Alkali activation effectively anchors cyano and hydroxyl active groups on the surface: hydroxyl groups enhance the material's hydrophilicity and promote proton transfer, while cyano groups exhibit electron-attracting characteristics to localize photogenerated electrons. Simultaneously, interlayer intercalation of K + &Na + forms electron transport channels, synergistically facilitating surface proton transfer and optimizing charge distribution. This multi-component modification strategy significantly enhances the adsorption capacity of O 2 , effectively modulates the 2e − ORR pathway, and improves the selectivity of H 2 O 2 , demonstrating its excellent bifunctional properties. Experimental data show that the optimally alkali-activated K 3 &Na 3 -C 3 N 5 achieves a remarkably high H 2 O 2 production rate of 26,920.49 μmol g −1 ·h −1 — a 90.3-fold increase over unmodified C 3 N 5 . This work pioneers alkali activation as a universal and scalable paradigm for engineering surface-active sites to enable performance amplification through functional group-metal ion cooperativity, and it provides a design blueprint for advanced carbon nitride-based photocatalysts to boost H 2 O 2 fuel cell performance.
✓ 已验证
产品关联
DOI
高影响因子
危险品化学品经营许可证（带存储）