APPLIED SURFACE SCIENCE
·
2016
·
IF 3.15
Xue Yu,Junjie Shi,Lijuan Feng,Chunhu Li,Liang Wang
A series of BiOBr/reduced graphene oxide (RGO) aerogel was fabricated using a two steps hydrothermal method. Various methods such as SEM, TEM, DRS and Raman spectroscopy were employed to fully characterize the as-obtained BiOBr/RGO. Their photocatalytic degradation of methyl orange (MO) were studied under visible light irradiation. The combination of BiOBr and RGO result in an improved activity. The sample with 10 wt% RGO abbreviated as BiOBr-G10 shows the highest activity. Moreover, this sample exhibits a selective visible-light photocatalytic behavior as the degradation rate over MO (80%) is much higher than that over Rhodamin B (50%) and phenol (35%) in 60 min. The XRD and photoluminescence emission spectroscopy characterization of the BiOBr-G10 samples indicates an increased crystallization of BiOBr and efficient quenching of photo-excited electrons and holes contributes to the improved photocatalytic activities.
✓ 已验证
产品关联
DOI
高影响因子
JOURNAL OF ELECTROANALYTICAL CHEMISTRY
·
2017
·
IF 3.012
Shuo Duan,Yuming Huang
A novel electrochemical sensor was developed for the sensitive and selective detection of Cu 2 + , Pb 2 + and Cd 2 + , which was based on NH 2 -MIL-88(Fe)-rGO composite modified glass carbon electrode (NH 2 -MIL-88(Fe)-rGO/GCE). The NH 2 -MIL-88(Fe)-rGO composite was facilely prepared by a one-step method and characterized by SEM, XRD, Raman spectrum and electrochemical methods. The stepwise GCE modified process was investigated by cyclic voltammetry (CV) and electrochemical impedance spectroscopy (EIS). The electrochemical behaviors of Cu 2 + , Pb 2 + and Cd 2 + ions on the NH 2 -MIL-88(Fe)-rGO/GCE were explored by differential pulse anodic stripping voltammetry (DPASV). It was found that NH 2 -MIL-88(Fe)-rGO was capable of adsorbing Cu 2 + , Pb 2 + and Cd 2 + ions from aqueous solutions and the NH 2 -MIL-88(Fe)-rGO/GCE could enhance the electrochemical responses of Cu 2 + , Pb 2 + and Cd 2 + effectively. Important operational parameters such as electrolyte pH and deposition time were investigated and optimized for the determination of trace Cu 2 + , Pb 2 + and Cd 2 + ions. Under the optimum conditions, the proposed electrochemical sensor had a linear range of 0.005––0.3 μM for Cd 2 + , 0.01–0.3 μM for Pb 2 + and 0.005–0.05 μM for Cu 2 + , respectively. The limits of detection (LODs) are 4.9 nM for Cd 2 + , 10 nM for Pb 2 + and 3.6 nM for Cu 2 + , respectively. The proposed method has been successfully applied to determine three metal ions in water samples. The developed sensor promises simple preparation, fast operation, good sensitivity and excellent reusability, showing great potential for monitoring of water quality.
✓ 已验证
产品关联
DOI
高影响因子
RSC Advances
·
2017
·Vol. 7
·期 64
·40673-40681
·
IF 3.108
Xinlin Liu,Yingying Qin,Yongsheng Yan,Peng Lv
A magnetic photocatalyst, CdS/CoFe2O4/rGO, has been successfully prepared via a simple hydrothermal method. The photocatalytic activity of the as-obtained composite photocatalyst was evaluated using the degradation of tetracycline. When compared with single CdS and CoFe2O4, the hybrid material (CdS/CoFe2O4/rGO) can enhance the photocatalytic activity. The photocurrent responses and PL spectra indicate that the composite photocatalyst can effectively separate the electron–hole pairs and restrain their recombination. This was attributed to the high charge carrier mobility of rGO and the heterostructured photocatalytic system, which promotes the separation of charge carriers. In all, the CdS/CoFe2O4/rGO photocatalyst, as a strong magnetic photocatalyst, is promising for further practical application in wastewater treatment.
✓ 已验证
产品关联
DOI
高影响因子
JOURNAL OF NANOPARTICLE RESEARCH
·
2017
·Vol. 19
·期 5
·1-11
·
IF 2.02
Feng Jiantao,Wang Yechen,Hou Yanhui,Li Liangchao
Hierarchical structured ZnFe 2 O 4 @reduced graphite oxide@TiO 2 (ZnFe 2 O 4 @RGO@TiO 2 ) nanocomposite was prepared by an electrostatic layer-by-layer route, which played a synthetic effect of Fenton oxidation of ZnFe 2 O 4 and photocatalytic oxidation of TiO 2 to degrade fulvic acid (FA) solution under visible-light irradiation. In this method, RGO, as the middle layer, can effectively promote the photo-induced electron flow between the ZnFe 2 O 4 and TiO 2 and further improve the efficiency of the photo-Fenton oxidation. The influencing factors on photo-Fenton oxidation, including solution pH, catalyst, and H 2 O 2 dosage, have also been investigated. The results illustrated that the ternary composite presented the enhanced catalytic performance. Under visible light irradiation, the degradation efficiency of the sample on the FA solution can reach 95.4% within 3 h. In addition, the catalyst exhibited superior stability and reusability, and its degradation efficiency was still up to 90% after 5 cycles. Therefore, the composite will be a kind of efficient photocatalyst and had a promising application for visible-light driven destruction of organic pollutants.
✓ 已验证
产品关联
DOI
高影响因子
Materials Research Express
·
2017
·Vol. 4
·期 2
·025605
·
IF 1.068
Xiaoqing Dai
Nano ZnO enhanced 3D porous reduced graphene oxide (RGO) with superior electromagnetic interferece (EMI) shielding efficiency (SE) was fabricated through a UV enhanced hydrothermal process. In this study, a composite with 10 wt% of 3D-RGO/ZnO was tested in a broadband frequency range from 2 to 18 GHz. Under the whole test conditions, the ratio of SEA/SET is higher than 50% and the maximum value can reach to 94%, indicating the shielding mechanism mainly attributes to absorption. The EMI SE showed that the thinnest thicknesses to shield different frequency range are 0.7 mm for 10 dB, 1.6 mm for 20 dB and 3.7 mm for 30 dB, which suggests 3D-RGO/ZnO could meet the requirement of new generate EMI shielding material.
✓ 已验证
产品关联
DOI
高影响因子
International Journal of Minerals Metallurgy and Materials
·
2024
·Vol. 30
·期 12
·2432-2440
·
IF 5.6
Cao Duanhao,Ma Xiaofeng,Zhang Yipeng,Ta La,Yang Yakun,Xu Chao,Ye Feng,Liu Jianguo
Exploring and designing a high-performance non-noble metal catalyst for hydrogen evolution reaction (HER) are crucial for the large-scale application of H 2 by water electrolysis. Here, novel catalysts with NiMo nanoparticles decorated on reduced graphene oxide (NiMo@rGO) synthesized by a two-step hydrothermal method were reported. Physical characterization results showed that the prepared NiMo@rGO-1 had an irregular lamellar structure, and the NiMo nanoparticles were uniformly dispersed on the rGO. NiMo@rGO-1 exhibited outstanding HER performance in an alkaline environment and required only 93 and 180 mV overpotential for HER in 1.0 M KOH solution to obtain current densities of −10 and −50 mA·cm − 2 , respectively. Stability tests showed that NiMo@rGO-1 had a certain operating stability for 32 h. Under the same condition, the performance of NiMo@rGO-1 can be comparable with that of commercial Pt/C catalysts at high current density. The synergistic effect between NiMo particles and lamellate graphene can remarkably promote charge transfer in electrocatalytic reactions. As a result, NiMo@rGO-1 presented the advantages of high intrinsic activity, large specific surface area, and small electrical impedance. The lamellar graphene played a role in dispersion to prevent the aggregation of nanoparticles. The prepared NiMo@rGO-1 can be used in an-ion exchange membrane water electrolysis to produce hydrogen. This study provides a simple preparation method for efficient and low-cost water electrolysis to produce hydrogen in the future.
✓ 已验证
产品关联
DOI
高影响因子
RARE METALS
·
2024
·
IF 9.6
Wan Wen-Qiang,Liang Kai-Ming,Zhu Peng-Yu,Chen Xiang-Yu,Li Zhen-Feng,Liu Shi-Yu,Zhang Shuai,Song Yang,He Peng,Wong Yew-Hoong,Zhang Shu-Ye
Wearable, flexible devices have garnered widespread attention in the realm of human motion and life activity detection. Currently, the development of simple, green, and easily scalable methods for fabricating strain sensors still presents significant challenges. In this study, we successfully modified the surface of reduced graphene oxide (rGO) with SnCuNiIn multi-component alloy nanoparticles (MCA NPs), with an average size of 13.29 nm, utilizing a green and facile microwave heating approach. Leveraging the SnCuNiIn MCA NPs/rGO powder, we formulated a conductive ink based on water and ethylene glycol, which, when screen-printed, yielded conductive patterns with a minimum resistivity of 4.366 mΩ·cm. Strain sensors produced using this ink demonstrate exceptional performance, demonstrating favorable resistance change rates during a single bending process that meets practical application requirements, and enduring 5000 bending cycles with a resistance change of less than 5%. These sensors exhibited a high gauge factor (GF max = 52.7) and outstanding cycling stability. Lastly, strain sensors are employed to monitor human normal life activities and motion states, showcasing significant potential for application in wearable electronic products. Graphical abstract
✓ 已验证
产品关联
DOI
高影响因子
BIOELECTROCHEMISTRY
·
2024
·
IF 4.8
Guiyin Li,Wenzhan Li,Yu Zhou,Xiaohong Tan,Qing Huang,Jintao Liang,Zhide Zhou
Glypican-3 (GPC3) is exclusively overexpressed in most Hepatocellular carcinoma (HCC) tissue but not in normal liver tissue, making it a promising biomarker for the precise detection of HCC. In this paper, a label-free light-addressable potentiometric sensor (LAPS) decorated by platinumpalladium-hemin-reduced graphene oxide nanocomposites (PtPd@H-rGO NCs) was constructed for determination of GPC3. The GPC3 aptamer (GPC3 Apt ) and PtPd@H-rGO NCs were modified on the surface of silicon-based LAPS chip to build sensitive unit of LAPS system. A readout photocurrent elicited from a modulated light source, registers the localized surface potential change. When a bias voltage is provided to the LAPS system, the GPC3-GPC3 Apt complexes formed by the specific reaction between GPC3 and GPC3 Apt at the sensing interface can cause the sensitive membrane surface potential to change, resulting in the photocurrent-voltage (I-V) curves generate a corresponding offset response. Therefore GPC3 concentration can be determined by monitoring the potential shifts (△V). Under optimal conditions, the potential shift is linearly related to the concentration of GPC3 in the range of 0.001–3.00 μg/mL with the limit of detection (LOD) of 0.0001 μg/mL. The LAPS has a good analytical performance with good specificity, reproducibility and stability, and can be used for the detection of GPC3 in actual serum samples, which provides a broad application prospect for the combined application of LAPS and aptamers in biooassay.
✓ 已验证
产品关联
DOI
PubMed
高影响因子
MATERIALS RESEARCH BULLETIN
·
2024
·
IF 5.3
Yupeng Zou,Yu Ma,Lingsai Meng,Shengxiang Xiong,Lijuan Cai,Gang Chen,Chengjun Dong,Hongtao Guan
In this work, reduced graphene oxide (RGO)-based composites loaded with magnetic CoFe 2 O 4 (CFO) and CoFe were successfully synthesized via heat treatment of basic ferric cobalt carbonate (BFCC) under different temperatures. The impact of adding CFO and CoFe on the electromagnetic parameters and absorption properties was investigated. When 40 wt% CFO flakes and CoFe particles are added to the RGO matrix and the filler content is 20 wt% in paraffin, there gives a reflection loss of −48 dB with a 5.5 GHz absorption bandwidth at 2.1 mm thickness, and −50 dB with 4.8 GHz at 2.9 mm, respectively. The coupling of a magnetic medium can change the electromagnetic loss mechanism in the material, which ultimately affects the absorption properties of the material. This study provides a good basis for the design of composite materials of RGO as microwave absorbing materials, enabling large-scale production of high-performance absorption materials.
✓ 已验证
产品关联
DOI
高影响因子
International Journal of Electrochemical Science
·
2025
·
IF 2.4
Gaosheng Nie,Xiongfei Sun,Liyin Xu,Ke Wu,Zilong Wei,Shuwu Liu
MOF-derived cobalt oxides (CoO x ) have attracted extensive attentions due to their excellent theoretical specific capacitances, permanent porosity and controllable structures. However, the inherent poor conductivity of single-component cobalt oxide, and the structural collapse, pore loss and agglomeration during pyrolysis process are still the main factors to limit the performance of CoO x . Structure design of 3D hierarchical porous heterostructure composites through 0D/1D/2D materials is an effective strategy for boosting the capacitive performance of CoO x . Herein, the rationally designed 3D hierarchically porous CoO x /MWCNTs/rGO ternary hybrid composite was constructed through high-temperature pyrolysis of a facile self-assembled 0D/1D/2D Co-MOF/MWCNTs/GO precursor. Indeed, The CoO x /MWCNTs/rGO electrode exhibited an excellent specific capacitance of 520 F g −1 at 0.5 A g −1 , outstanding rate capability of 80.77 % capacitance retention even at 20 A g −1 , and ideal durability with about 8.4 % capacitance decay after 10000 cycles. Moreover, the CoO x /MWCNTs/rGO exhibited a maximum energy density of 14.6 Wh kg −1 with a power density of 41.2 W kg −1 .
✓ 已验证
产品关联
DOI
高影响因子
ANALYST
·
2024
·
IF 3.6
Wanjin Huang,Shufei Tang,Wei Xiao,Yafei Chen,Lijun Li,Jianping Li
A reduced graphene oxide/molybdenum selenosulfide (rGO/MoSSe) heterojunction was synthesized, and a molecularly imprinted photoelectrochemical sensor for the detection of chlortetracycline was prepared. MoSSe was grown in situ on rGO by a hydrothermal method to form an rGO/MoSSe heterojunction, which acts as the sensitive film of the sensor. Since rGO can promote electron transfer and effectively inhibit electron–hole recombination, it effectively reduces the recombination probability of electrons and holes and improves the photoelectric efficiency, thus enhancing the detection sensitivity of the PEC sensor. The rGO/MoSSe was immobilized on an FTO electrode, and molecularly imprinted polymers (MIPs) were prepared by electropolymerization on the rGO/MoSSe-modified FTO electrode with chlortetracycline as the template molecule and o-phenylenediamine as the functional monomer, so as to construct a molecularly imprinted photoelectrochemical (MIP-PEC) sensor. The determination of chlortetracycline was realized by the strategy of a “gate-controlled effect”, and the detection range of the chlortetracycline concentration was 5.0 × 10−13–5 × 10−9 mol L−1 with a detection limit of 1.57 × 10−13 mol L−1. The sensor has been applied to the determination of chlortetracycline in animal-derived food samples.
✓ 已验证
产品关联
DOI
PubMed
高影响因子
MICROCHEMICAL JOURNAL
·
2024
·
IF 4.9
Yu-Ying Xin,Li-Hong Liu,Yan Liu,Zhao-Peng Deng,Xiao-Li Cheng,Xian-Fa Zhang,Ying-Ming Xu,Li-Hua Huo,Shan Gao
The development of electrochemical dopamine (DA) sensor with anti-interfering ascorbic acid and uric acid is challenging due to the presence of their overlapping electrical signals. Herein, MoS 2 nanoflower assembled from ultrathin nanosheets were uniformly loaded on rGO substrate through one-step hydrothermal reaction. Then, the composite (MoS 2 /rGO) was modified on the surface of glassy carbon electrode (GCE) by a drop coating method, successfully assembling non-enzymatic electrochemical sensor for ultra-selective DA detection. The test results show that the MoS 2 /rGO/GCE probe exhibits good sensitivity (15.73 μA μM −1 cm −2 ), small limit of detection (13 nM) and wide range of detection (0.1 ∼ 110.0 μM) for DA in 0.1 M PBS medium (pH = 7.4), as well as good interference resistance, reproducibility and stability. This excellent sensing ability mainly stems from the synergistic effect of the prepared electrode material with abundant edge defects, small charge transfer resistance, large electrochemically active area, and more negative Zeta potential (–23.4 mV). Furthermore, the satisfactory and accurate detection of DA content in animal serums predicts its potential for practical applications in related biological aspects.
✓ 已验证
产品关联
DOI
高影响因子
危险品化学品经营许可证（带存储）