JOURNAL OF HAZARDOUS MATERIALS
·
2017
·
IF 6.065
Jianxian Zeng,Zhihui Dong,Zhe Zhang,Yuan Liu
A surface-grafted imprinted ceramic membrane (IIP-PVI/CM) for recognizing molybdate (Mo(VI)) anion was prepared by surface-initiated graft-polymerization. Firstly, raw alumina ceramic membrane (CM) was deposited with SiO 2 active layer by situ hydrolysis deposition method. Subsequently, γ-methacryloxy propyl trimethoxyl silane (MPS) was used as a coupling agent to introduce double bonds onto the SiO 2 layer (MPS-CM). Then, 1-vinylimidazole (VI) was employed as a functional monomer to graft-polymerization onto the MPS-CM (PVI-CM). During the graft-polymerization, the influence factors of grafting degree of PVI were investigated in detail. Under optimum conditions (monomer concentration 20 wt%, temperature 70 °C, initiator amount 1.1 wt% and reaction time 8 h), the grafting degree of 20.39 g/100 g was obtained. Further, Mo(VI) anion was used as a template to imprint in the PVI-CM by employing 1,6-dibromohexane as a cross-linking agent, and then Mo(VI) was removed, obtaining the IIP-PVI/CM with many imprinted cavities for Mo(VI). Thereafter, static adsorption and dynamic separation properties of IIP-PVI/CM for Mo(VI) were studied. Results indicate that IIP-PVI/CM shows a specific selectivity for Mo(VI) with the adsorption capacity of 0.69 mmol/100 g, and the selectivity coefficient of IIP-PVI/CM is 7.48 for molybdate to tungstate anions. During the dynamic separation, IIP-PVI/CM has also good selectivity for separation of Mo(VI) and W(VI) anions.
研究领域:
环境化学
·
材料科学
·
分离科学
·
高分子化学
·
无机分析化学
✓ 已验证
DOI
高影响因子
JOURNAL OF ALLOYS AND COMPOUNDS
·
2018
·
IF 3.779
Ruichong Chen,Jianqi Qi,Lin Su,Qiwu Shi,Xiaofeng Guo,Di Wu,Tiecheng Lu,Zhijun Liao
In this work, we report a rapid, simple and controllable approach to prepare B 4 C ceramic double-curvature shells by dropping the coating slurry on a molybdenum (Mo) substrate. The B 4 C slurry finally forms a nearly uniform spherical thin shell on the Mo substrates after drainage and curing process. We discovered that the uniformity and the wall thickness of the thin shell structure are controlled by the curing time and the viscosity of the slurry, respectively. This novel fabrication method not only provides an alternative way to prepare B 4 C ceramic double-curvature shells for the potential application as an ICF capsule, but also sheds light on the uniformity control of other ceramic double-curvature thin shells.
研究领域:
材料科学
·
核聚变工程
·
先进陶瓷制备
·
表面涂层技术
·
功能材料
✓ 已验证
DOI
高影响因子
Journal of Materiomics
·
2022
·Vol. 9
·期 3
·568-576
·
IF 8.589
Qiujun Wang,Weiqi Zhu,Ya Su,Di Zhang,Zhaojin Li,Huan Wang,Huilan Sun,Bo Wang,Dan Zhou,Li-Zhen Fan
Lithium metal batteries based on solid electrolytes are considered as promising candidates with high energy density and safety. However, the weak solid-solid contact between electrolyte and electrode can easily lead to interface instability and lithium ions discontinuous migration, which seriously reduces the electrochemical performance of the battery. Herein, we construct a soft gel interfacial layer to improve the stability of the solid-solid interface between electrolyte and electrode by means of polyester-based monomers and imidazole-based ionic liquids. Based on this, garnet-type Li 6.4 La 3 Zr 1.4 Ta 0.6 O 12 (LLZTO) particles as inorganic ceramic filler were introduced in the layer to obtain composite electrolytes with high ionic conductivity (up to 1.1 × 10 −3 S/cm at 25 °C). As a result, the assembled lithium symmetric battery of Li|THCE-15%LLZTO|Li suggests excellent cycling stability with 700 h at 0.1 mA/cm 2 at 50 °C, and the lithium metal batteries of LFP|THCE-15%LLZTO|Li delivers high initial discharge capacity of 128.2 mA ·h/g with capacity retain of 75.48% after 150 cycles at 2 C. This work paves a new route to build safe and stable lithium metal batteries with synergistic introduction of composite electrolytes between electrolyte and electrode using soft gel interfacial layer and inorganic filler.
研究领域:
电化学
·
材料科学
·
能源存储
·
固体离子学
·
界面工程
✓ 已验证
DOI
高影响因子
ELECTROCHIMICA ACTA
·
2020
·
IF 6.215
Shi Wang,Qingyuan Li,Minglei Bai,Jixin He,Chongyang Liu,Zengxi Li,Xiangfeng Liu,Wen-yong Lai,Liaoyun Zhang
Lithium-ion batteries (LIBs) using solid-state electrolytes (SSEs) can improve safety and energy density comparable with the liquid electrolytes (LE)-based counterparts. Especially, employing garnet-type SSEs to prepare solid-state LIBs are promising to achieve high-energy cells. However, the unbending and brittle issues of the inorganic SSE films are not suitable to fabricate flexible and stretchable energy storage devices. Here, We find that introducing specific polymer (30 wt%) into Li 6.75 La 3 Zr 1.75 Ta 0.25 O 12 (LLZTO) can strongly increase the strength of the composite polymer-in-inorganic electrolyte (CIE) film. Both in-situ and ex-situ characterizations demonstrate that CIE delivers an excellent ability to suppress the growth of Li dendrites due to the close packing of LLZTO and effective filled grain boundaries and voids inside the CIE film by the polymer. The CIE inherits impressive electrochemical performance from LLZTO. As a result, the assembled LiFePO 4 (LFP)/CIE/Li cell delivers better cell performance than LFP/LE-separator/Li cell at ambient temperature (AT). The assembled high-voltage cathode (Li 1.2 Mn 0.6 Ni 0.2 O 2 , 4.8 V)/CIE/Li cell also displays an excellent cell performance at AT. The present study offers new insights into exploring of flexible polymer-in-ceramic electrolytes for high-voltage LIBs with improved safety and energy density .
研究领域:
材料科学
·
电化学
·
能源存储
·
固态电池
·
纳米复合材料
·
界面工程
✓ 已验证
DOI
高影响因子
CERAMICS INTERNATIONAL
·
2021
·Vol. 48
·期 3
·3081-3095
·
IF 4.527
Mingchao Wang,Zhaoli Chen,Jingxuan Liu,Zhaojie Feng,Jingfang Zhang,Wenzheng Zhai,Haijun Zhang
To meet the high demand for ceramic/superalloy composite structural components in various fields, an advanced high-temperature adhesion technique was firstly developed by preparing a novel inorganic/organic hybrid adhesive suitable for ZrO 2 and TC4 . Chemical bonding started to work at ∼600°C, and became the crucial bonding mechanism at elevated temperatures. The formation of ZrSiO 4 and Ti 5 Si 3 at the interfaces of two substrates not only increased the interfacial connection strength , but also formed two gradient layers with a size of ∼2 μm to effectively alleviate the difference of composition and performance between the adhesive and substrates. In the temperature range of 500–900°C, the matching degree of CTE among ZrO 2 , adhesive and TC4 is higher, and the maximum difference does not exceed 3×10 -6 K -1 . Meanwhile, the formation of a composite structure containing various ceramics (ZrO 2 , SiC and ZrB 2 ) and intermetallics (Ni–Si, Al–Ni), and the improvement of structural compactness of adhesive from 500 to 900°C greatly improved the bonding strength to the maximum value of 31.4 MPa at 900°C. Also, the adhesive pretreated at 900°C showed good thermal cycling resistance, and the strength was still higher than 15 MPa after 50 cycles. For cured adhesive, when used directly in an extreme environment, it can provide bonding strength not less than 5 MPa in the whole temperature range, indicating that the adhesive possessed potential emergency repair convenience. This work significantly broadened the application of high-temperature-resistant adhesion technology in the connection of dissimilar ceramics and alloys.
研究领域:
材料科学
·
复合材料
·
界面工程
·
高温功能材料
·
连接技术
✓ 已验证
DOI
高影响因子
Journal of Materiomics
·
2022
·Vol. 8
·期 5
·1001-1008
·
IF 8.589
Xiaoyang Wang,Chun Li,Qihan Zhou,Mingshen Li,Mushi Zheng,Junlei Qi,Xiaoqing Si,Jian Cao
One of the critical challenges for the protonic ceramic fuel cell stack is sealing electrolytes and interconnects. However, the traditional Ag CuO sealant will aggravate the oxidation along the interconnect surface and result in brittle compound layers at the BaZr 0.1 Ce 0.7 Y 0.1 Yb 0.1 O 3- δ (BZCYYb) electrolyte interface. The present work demonstrates that a silver particle interlayer with high dislocation density can be adopted to join BZCYYb electrolyte to the interconnect (AISI 441 stainless) in air instead of traditional Ag CuO sealant. Elevating temperatures result in a sufficient bonding at the Ag/BZCYYb interface, and a defect-free joint is obtained at 950 °C. Atomic bonding at Ag/BZCYYb interface is confirmed by TEM. Also, a dense and thin oxide layer (2–3 μm) is formed along the AISI 441 interface. Ag particles in the interlayer provide the main driving force for the sintering joining. The massive dislocations promote the recovery and recrystallization of the Ag interlayer, as well as the interdiffusion of BZCYYb/Ag. After aging in the wet oxidizing atmosphere at 600 °C for 300 h, joints remain intact and dense, indicating superior oxidation resistance and aging performance. Besides, the joint shear strength (25.3 MPa) is 59 % higher than that of the joint brazed by traditional Ag CuO.
研究领域:
材料科学
·
固态离子学
·
能源材料
·
电化学
·
连接技术
·
高温材料
✓ 已验证
DOI
高影响因子
JOURNAL OF LUMINESCENCE
·
2018
·
IF 2.732
Qinghua Yang,Benxue Jiang,Shuilin Chen,Yiguang Jiang,Pande Zhang,Jun Wang,Shiqing Xu,Long Zhang
Al 2 O 3 : Er 3+ /Yb 3+ transparent ceramics codoped with Zn 2+ ions with intense upconversion and near infrared emission were prepared by conventional solid-state reaction and vacuum and hot isostatic pressing sintering. The effects of Zn 2+ incorporation to the structure, transparent, upconversion and NIR luminescence were discussed in detail. The as prepared Al 2 O 3 ceramics exhibited a total transmittance of ~ 75% in infrared regions (800–3300 nm) and ~ 50% in visible regions (500–800 nm). Under the excitation of a 980 nm laser diode , the as prepared Al 2 O 3 ceramics displayed two tense upconversion emission peaks of a green one centered at 550 nm and a red one centered at 660 nm and a tense near infrared emission peak centered at 1.532 µm, characteristic of Er 3+ emission. Compared with Er 3+ /Yb 3+ doped only, Zn 2+ codoped Al 2 O 3 :Er 3+ /Yb 3+ transparent ceramics showed higher upconversion and near infrared emission of ~ 11 times and ~ 4 times, respectively. The enhancement mechanism due to incorporation of Zn 2+ ions was also discussed in detail.
研究领域:
材料科学
·
光学材料
·
无机非金属材料
·
发光材料
·
陶瓷工程
✓ 已验证
DOI
高影响因子
RSC Advances
·
2014
·Vol. 4
·期 52
·27259-27266
·
IF 3.708
Libin Yang,Feng Xin,Junzhong Lin,Zhuang Zhuang,Rui Sun
In this study, a hydrothermal synthesis was developed to prepare a thin titanium silicalite-1 catalyst layer in the internal channels of the honeycomb cordierite support, which was used in a continuous heterogeneous reaction. The as-prepared thin TS-1 catalyst layer was characterized by SEM, XRD, UV-vis and ATR-FTIR methods. Multiple hydrothermal syntheses were used for controlling the crystalline growth to optimize catalytic activity and lifetime. Moreover, a monolithic TS-1/cordierite reactor with external looping was utilized to investigate the characteristics of the continuous heterogeneous ammoximation reaction without the organic solvent tert-butanol (TBA). The reaction results showed that the conversion of cyclohexanone and selectivity of oxime approached more than 0.96 and 0.98, respectively. When compared with the reaction using TBA as the reaction solvent, the activity of the monolithic TS-1/cordierite showed no differences except for a longer lifetime.
研究领域:
化学工程
·
催化化学
·
材料科学
·
工业化学
·
绿色化学
✓ 已验证
DOI
高影响因子
CERAMICS INTERNATIONAL
·
2020
·Vol. 46
·期 16
·25802-25807
·
IF 3.83
Jun Xiao,Yan Jia,Dongqing Liu,Haifeng Cheng
Manufacturing complexity and poor machinability hinder the preparation of complex-shaped ceramic composites. Three-dimensional printing can overcome this difficulty. Herein, we report a type of photocurable preceramic resin containing SiO 2 nanoparticles (up to 20 wt% of polymer), which do not affect the photocurability of the preceramic resin, and a small amount of SiC nanofibres (1 wt%). We successfully printed precise green bodies with a complex shape by digital light processing and converted them into ceramic composites via pyrolysis at 1300 °C under a N 2 atmosphere. The introduction of SiO 2 and SiC into the ceramic composites led to reduced weight loss of the composites during pyrolysis and a decrease in their porosity and enhancement in their mechanical properties after pyrolysis. The properties of the printed samples pyrolysed at different ramping rates were compared, and the effects of the microstructure on the mechanical properties of the composites were investigated.
研究领域:
材料科学
·
陶瓷工程
·
增材制造
·
高分子转化陶瓷
·
复合材料
✓ 已验证
DOI
高影响因子
JOURNAL OF POWER SOURCES
·
2017
·
IF 6.395
Hanyu Huo,Ning Zhao,Jiyang Sun,Fuming Du,Yiqiu Li,Xiangxin Guo
Paramount attention has been paid on solid polymer electrolytes due to their potential in enhancement of energy density as well as improvement of safety. Herein, the composite electrolytes consisting of Li-salt-free polyethylene oxides and 200 nm-sized Li 6.4 La 3 Zr 1.4 Ta 0.6 O 12 particles interfacially wetted by [BMIM]TF 2 N of 1.8 μL cm −2 have been prepared. Such wetted ionic liquid remains the solid state of membrane electrolytes and decreases the interface impedance between the electrodes and the electrolytes. There is no release of the liquid phase from the PEO matrix when the pressure of 5.0 × 10 4 Pa being applied for 24 h. The interfacially wetted membrane electrolytes show the conductivity of 2.2 × 10 −4 S cm −1 at 20 °C, which is one order of magnitude greater than that of the membranes without the wetted ionic liquids. The conduction mechanism is related to a large number of lithium ions releasing from Li 6.4 La 3 Zr 1.4 Ta 0.6 O 12 particles and the improved conductive paths along the ion-liquid-wetted interfaces between the polymer matrix and ceramic grains. When the membranes being used in the solid-state LiFePO 4 /Li and LiFe 0.15 Mn 0.85 PO 4 /Li cells at 25 °C, the excellent rate capability and superior cycle stability has been shown. The results provide a new prospect for solid polymer electrolytes used for room-temperature solid-state lithium batteries .
研究领域:
材料科学
·
电化学
·
能源材料
·
固态电池
·
高分子电解质
·
离子传导机制
✓ 已验证
DOI
高影响因子
CHEMICAL ENGINEERING JOURNAL
·
2024
·
IF 13.3
Yong Huang,Lida Xu,Qibin Zhuang,Xiong Zhou,Zhenjin Xu,Wei Xiao,Xin Liu,Qinnan Chen,Yang Zhao,Chao Wu,Daoheng Sun,Dezhi Wu
High-temperature heat flux sensors play a pivotal role in detecting the dynamic heat exchange processes of heating and cooling, in high-temperature environments. However, the detection of surface heat flux on curved parts operating at high temperatures remains a formidable challenge. Flexible thin-film heat flux sensors, while offering benefits such as conformal adhesion and excellent portability, are typically limited by low operational temperatures and narrow measurement ranges. This work proposes a high-temperature flexible heat flux sensor based on multi-layered high-temperature resistant ceramics nanofibre membranes that one layer worked as a substrate and the other two work as thermal resistance layers, and direct ink writing platinum sensitive elements with Wheatstone Bridge configuration. The prototype sensor is capable of quantifying heat flux reaching 1330 kW/m 2 and withstands temperature as high as 1200 °C. The sensor is bendable with resistance change only about 0.5 % even when the bending radius was larger than 10 mm. These extraordinary characteristics indicate that such methodology will offer a new way for the development of high-temperature thin-film flexible heat flux sensors, demonstrating considerable potential for applications in high-temperature environments.
研究领域:
传感器技术
·
材料科学
·
热物理学
·
仪器仪表工程
·
高温测量技术
✓ 已验证
DOI
高影响因子
Small
·
2023
·Vol. 19
·期 39
·2302691
·
IF 13.3
Jing Yu,Guodong Zhou,Yueqing Li,Yuhao Wang,Dengjie Chen,Francesco Ciucci
Composite polymer-ceramic electrolytes have shown considerable potential for high-energy-density Li-metal batteries as they combine the benefits of both polymers and ceramics. However, low ionic conductivity and poor contact with electrodes limit their practical usage. In this study, a highly conductive and stable composite electrolyte with a high ceramic loading is developed for high-energy-density Li-metal batteries. The electrolyte, produced through in situ polymerization and composed of a polymer called poly-1,3-dioxolane in a poly(vinylidene fluoride)/ceramic matrix, exhibits excellent room-temperature ionic conductivity of 1.2 mS cm −1 and high stability with Li metal over 1500 h. When tested in a Li|electrolyte|LiFePO 4 battery, the electrolyte delivers excellent cycling performance and rate capability at room temperature, with a discharge capacity of 137 mAh g −1 over 500 cycles at 1 C. Furthermore, the electrolyte not only exhibits a high Li + transference number of 0.76 but also significantly lowers contact resistance (from 157.8 to 2.1 Ω) relative to electrodes. When used in a battery with a high-voltage LiNi 0.8 Mn 0.1 Co 0.1 O 2 cathode, a discharge capacity of 140 mAh g −1 is achieved. These results show the potential of composite polymer-ceramic electrolytes in room-temperature solid-state Li-metal batteries and provide a strategy for designing highly conductive polymer-in-ceramic electrolytes with electrode-compatible interfaces.
研究领域:
材料科学
·
电化学
·
能源存储
·
固态电池
·
高分子化学
·
无机非金属材料
✓ 已验证
DOI
高影响因子
危险品化学品经营许可证（带存储）