Molecular Catalysis
·
2020
·
IF 3.687
Fanfan Yue,Ao Hu,Xinhuan Lu,Chenlong Wang,Haijun Pan,Haifu Zhang,Lu Yang,Qinghua Xia,Dan Zhou,Yongde Xia
Benzimidazole and metal cobalt salts were employed in the synthesis of Co-ZIF-9 by solvothermal crystallization. Highly active catalysts for selective hydrogenation of carbonyl compounds were developed. The optimal nanocatalyst Co-ZIF-350 manifested remarkable activity and selectivity for the hydrogenation of cyclohexanone under mild conditions. Catalytic conversion of cyclohexanone reached the highest over the catalyst of Co-ZIF-9-pyrolyzed at 350 °C for 2 h, in which the conversion of cyclohexanone was 100 % and the selectivity of cyclohexanol was ＞99 % at 50 °C. A wide scope of ketones/aromatic aldehydes could be selectively reduced to the corresponding alcohols with high yields. Importantly, the nanocatalyst Co-ZIF-350 presented good tolerance of substrates with various functional groups under mild conditions.
研究领域:
催化化学
·
材料科学
✓ 已验证
DOI
高影响因子
JOURNAL OF ALLOYS AND COMPOUNDS
·
2023
·
IF 6.2
Lingyao Zou,Lu Gan,Wenli Song,Chunying Rong,Lishan Yang,Liping Yu,Zhongyun Ma,Shixun Lian
The rapid development of highly durable electric vehicles has put forward higher requirements for lithium-ion batteries. Li 4 Ti 5 O 12 (LTO) is widely studied owing to its long service life and safety. However, owing to their low electrical conductivity and diffusion, lithium ions have limited practical applications. In this study, Co-Cl co-doped LTO/TiO 2 diphase (LTOT) nanosheets were prepared via the hydrothermal method . The synergistic effect of Co-Cl co-doping reduced the charge-transfer resistance of LTOT and increased the lithium-ion diffusion coefficient , thereby improving the dynamic behavior of the electrode material, which further enhances the rate capability and cycle performance of LTOT. The optimized LTOT:Co-Cl composite exhibited excellent cycle performance and rate capability (the ninth cycle reversible capacities were 253.8, 222.2, 200.1, 185.7, 169.9, 161.3, and 146.3 mAh·g −1 at the current density of 1, 2, 5, 10, 20, 30, and 50 C (1 C = 175 mA·g −1 ) rate, respectively). In addition, LTOT:Co-Cl maintained a capacity of 120 mAh·g −1 after 5000 cycles at 50 C with a retention rate of 83 %, indicating that the average decay rate per cycle is only 0.003 % during the long charge/discharge process.
研究领域:
材料科学
·
电化学
✓ 已验证
产品关联
DOI
高影响因子
Nature Communications
·
2024
·Vol. 15
·期 1
·1-11
·
IF 14.7
Xue Jing,Dong Xue,Liu Chunxiao,Li Jiawei,Dai Yizhou,Xue Weiqing,Luo Laihao,Ji Yuan,Zhang Xiao,Li Xu,Jiang Qiu,Zheng Tingting,Xiao Jianping,Xia Chuan
Using renewable electricity to convert CO 2 into CO offers a sustainable route to produce a versatile intermediate to synthesize various chemicals and fuels. For economic CO 2 -to-CO conversion at scale, however, there exists a trade-off between selectivity and activity, necessitating the delicate design of efficient catalysts to hit the sweet spot. We demonstrate here that copper co-alloyed with isolated antimony and palladium atoms can efficiently activate and convert CO 2 molecules into CO. This trimetallic single-atom alloy catalyst (Cu 92 Sb 5 Pd 3 ) achieves an outstanding CO selectivity of 100% (±1.5%) at −402 mA cm −2 and a high activity up to −1 A cm −2 in a neutral electrolyte, surpassing numerous state-of-the-art noble metal catalysts. Moreover, it exhibits long-term stability over 528 h at −100 mA cm −2 with an FE CO above 95%. Operando spectroscopy and theoretical simulation provide explicit evidence for the charge redistribution between Sb/Pd additions and Cu base, demonstrating that Sb and Pd single atoms synergistically shift the electronic structure of Cu for CO production and suppress hydrogen evolution. Additionally, the collaborative interactions enhance the overall stability of the catalyst. These results showcase that Sb/Pd-doped Cu can steadily carry out efficient CO 2 electrolysis under mild conditions, challenging the monopoly of noble metals in large-scale CO 2 -to-CO conversion.
研究领域:
材料科学
·
化学工程
·
电化学
·
可持续能源
✓ 已验证
产品关联
DOI
PubMed
高影响因子
JOURNAL OF LIQUID CHROMATOGRAPHY & RELATED TECHNOLOGIES
·
2015
·
IF 0.606
Haiyan Liu,Yamin Ma,Fengqing Wang,Jiafei Wang,Quanjie Liu
A new poly(1-dodecene-co-trimethylol propane triacrylate-co-ethylene dimethacrylate) [poly(C12-co-TMPTA-co-EDMA)] monolithic column was prepared via in situ free-radical polymerization reaction. Various parameters affecting the polymerization were investigated and optimized. The permeability of the monolithic column was calculated as 2.9098 × 10−14 m2 with methanol as the mobile phase and the surface areas was 73.1 m2/g by the nitrogen adsorption–desorption experiment. The morphologies of the monolith were characterized by scanning electron microscopy (SEM) and the mechanical strength has been studied in detail as well. The prepared monolith was then used as the stationary phase of reversed phase high-performance liquid chromatography (RP-HPLC) to separate small molecule compounds. Column efficiency for chlorobenzene reached 14,340 theoretical plates per meter. The monolith also showed satisfactory reproducibility, based on the retention times of benzene, phenol, chlorobenzene, diphenylamine, and anthracene; the relative standard deviation (RSD) values for run-to-run, column-to-column and batch-to-batch were less than 0.62%, 3.2%, and 5.7%, respectively.
研究领域:
分析化学
·
材料科学
✓ 已验证
DOI
高影响因子
Journal of Macromolecular Science Part B-Physics
·
2021
·
IF 1.504
Chao Zhang,Zhihua Zhou,Wenjuan Liu,Tianlong Huang,Yanmin Zhao,Ping Chen,Ziwei Zhou,Dan Wang,Meiling Yi,Jianjun Fang
Porous microspheres have interconnecting external and internal pore structure resulting in enormous specific surface area and have drawn attention for drug delivery. In this work, poly(l-lactide-co-glycolide-co-ε-caprolactone) (PLLGC) porous microspheres were prepared by a combined solvent evaporation and particle leaching method using gelatin as a porogen. The effects of preparation parameters on the morphologies of the porous microspheres were studied. The resultant microspheres showed porous surfaces and a three-dimensional internal network structure with interconnecting pores. The porous microsphere size decreased with increasing stirring speed and decreasing PLLGC concentration. There were fewer micropores on the surfaces of the microspheres with increasing temperature. The number of the pores and pore size on the surface of the microspheres increased with increasing gelatin content. By appropriate control of these factors (stirring speed 300 rpm, PLLGC solution concentration 1.0 wt%, temperature 0 °C, and gelatin concentration 7.5 wt%), a suitable porous microsphere, with a mean diameter of 200 μm, was prepared as a potential drug delivery agent.
研究领域:
材料科学
·
高分子科学
·
药剂技术
·
生物医学工程
·
药物递送系统
✓ 已验证
DOI
高影响因子
CERAMICS INTERNATIONAL
·
2023
·
IF 5.2
Hongming Liu,Jingxin Wang,Hai Xiong,Yue Chen,Jianzhong Xiao,Chao Wang
Restricted by an insufficient understanding of the compositional and structural characteristics of the sensing materials that affect the sensing performances, the YSZ-based CO gas sensor remains in a dilemma in terms of further promoting sensitivity, selectivity and long-term stability. In this work, two bimetallic oxides with different crystal structures, perovskite SmMnO 3 and mullite SmMn 2 O 5 , were prepared and adopted to elucidate the roles of the Mn 3+ , Mn 4+ and surface oxygen vacancies . Compared with SmMnO 3 , the coexisting coordination modes of Mn 3+ and Mn 4+ in SmMn 2 O 5 is conducive to generating oxygen vacancies. Furthermore, a SmMn 2 O 5 -based sensor with more oxygen vacancies demonstrates a relatively faster response/recovery speed and enhanced sensitivity of 2.05 times that of SmMnO 3 under the same operation conditions. Such work may broaden insight into the development of efficient sensing materials that introduce oxygen vacancies through the construction of phase structures without complicated operations. Overall, the sensor attached to SmMn 2 O 5 exhibits a low detection limit (5 ppm), a feasible response/recovery speed (24 s/28 s toward 40 ppm CO operating at 450 °C), satisfactory CO selectivity and long-term stability, highlighting its potential for CO monitoring in harsh environments.
研究领域:
材料科学
·
传感器技术
✓ 已验证
DOI
高影响因子
APPLIED SURFACE SCIENCE
·
2025
·
IF 6.9
Xiaolin Shi,Guo Yang,Bo Xing,Caiyi Jiang,Hangdao Qin,Min Li,Fuping Zhang,Yi Wang,Dongzheng Wang,Xingyong Liu
Fluorine-containing wastewater seriously threatens human health due to the wide application of sodium p -perfluorous nonenoxybenzenesulfonate (OBS). Herein, a novel Fe-Co bimetallic biochar (Fe-Co@BC) with abundant pore structure, functional groups and quickly electron transfer capability was prepared using hydrothermal method. Meanwhile, Fe-Co@BC-Ⅰ exhibited a superior catalytic capacity for degradation of OBS in PMS system, and the removal efficiency of OBS reached to 94.1 % within 60 min. After three cycles, the removal efficiency of OBS still up to 80 % and the Fe-Co had almost no leaching (Fe: 0.006 mg/L; Co: 0.023 mg/L). Further mechanistic insights were verified that high catalytic capacity and stability ascribed to the synergistic effects of Fe and Co, where Fe-Co mutual interaction promoted the formation of Fe 2+ and Co 2+ and accelerated electron transfer of catalyst. In addition, the quenching experiments and electron paramagnetic resonance (EPR) proved that the degradation of OBS can be mainly ascribed to indirect oxidation of SO 4 −• , O 2 −• and •OH, and the possible degradation pathway of OBS was proposed in the Fe-Co@BC/PMS system. This study provides an insight into bimetallic prepared and activation PMS degradation fluorinated wastewater.
研究领域:
环境科学
·
化学工程
✓ 已验证
产品关联
DOI
高影响因子
Catalysts
·
2022
·Vol. 13
·期 1
·70
·
IF 4.501
Wei Chen,Huan Shen,Xiaoxiao Zhu,Guoli Liu,Chuanqi Pan,Fajun Huang,Yarong Fang,Yanbing Guo,Zhu Luo
In this study, CuO loaded on anatase TiO2catalysts (CuO/anatase) with oxygen vacancies was synthesized via reduction treatments by NaHB4and H2(CuO/anatase-B, CuO/anatase-H), respectively. The characterizations suggest that different reduction treatments bring different concentration of oxygen vacancies in the CuO/anatase catalysts, which finally affect the CO catalytic performance. The CuO/anatase-B and CuO/anatase-H exhibit CO conversion of 90% at 182 and 198 °C, respectively, which is lower than what occurred for CuO/anatase (300 °C). The XRD, Raman, and EPR results show that the amount of the oxygen vacancies of the CuO/anatase-H is the largest, indicating a stronger reduction effect of H2than NaHB4on the anatase surface. The in situ DRIFTS results exhibit that the Cu sites are the adsorption sites of CO, and the oxygen vacancies on the anatase can active the O2molecules into reactive oxygen species. According to the in situ DRIFTS results, it can be concluded that in the CO oxidation reaction, only the CuO/anatase-H catalyst can be carried out by the Mvk mechanism, which greatly improves its catalytic efficiency. This study explained the reaction mechanisms of CO oxidation on various anatase surfaces, which offers detailed insights into how to prepare suitable catalysts for low-temperature oxidation reactions.Keywords:CuO/anatase;H2reduction treatment;oxygen vacancies;CO catalytic oxidation;CO reaction mechanism
研究领域:
催化化学
·
材料科学
✓ 已验证
产品关联
DOI
高影响因子
Small
·
2023
·
IF 13.3
Jiajin Lin,Shuaiqi Zhao,Jin Yang,Wei-Hsiang Huang,Chi-Liang Chen,Tingyu Chen,Yun Zhao,Guangxu Chen,Yongcai Qiu,Lin Gu
The development of catalysts with abundant active interfaces for superior low-temperature catalytic CO oxidation is critical to meet increasingly rigorous emission requirements, yet still challenging. Herein, this work reports a PtCo/CoO x /Al 2 O 3 catalyst with PtCo clusters and enriched Pt─O─Co interfaces induced by hydrogen spillover from the Pt sites and self-oxidation process in air, exhibiting excellent performance for CO oxidation at low temperatures and humid conditions. The combination of structural characterizations and in situ Fourier transform infrared spectroscopy reveals that the PtCo cluster effectively prevents CO saturation/poisoning on the Pt surface. Additionally, the presence of Pt─O─Co interfaces in the PtCo/CoO x /Al 2 O 3 catalyst provides a significant number of active sites for oxygen activation and ─OH formation. This facilitates efficient generation of CO 2 at ambient temperature by coupling with nearby adsorbed CO molecules, resulting in superior low-temperature activity and long-term stability for CO oxidation under humid conditions. This work provides a facile route toward rationalizing the design of catalysts with more active interfaces for superior low-temperature CO oxidation under humid conditions for practical applications.
研究领域:
催化
·
材料科学
·
环境科学
✓ 已验证
产品关联
DOI
PubMed
高影响因子
JOURNAL OF CHEMICAL SCIENCES
·
2022
·Vol. 134
·期 2
·1-11
·
IF 2.15
Yu Miao,Ji Shuai,Li Zhifang,Song Kun,Li Yueyu,Yang Jian,Yang Changlong
A simple ion-exchange method is used to prepare Mn and Co-supported TNU-9 denitration catalyst for NH 3 -SCR. The denitration activity and H 2 O/SO 2 resistance performance of the catalyst are systematically studied. The denitration activity test exhibits that the NO x removal rate of Mn-Co/TNU-9 is higher than that of Mn/TNU-9 and Co/TNU-9, the NO x removal rate is greater than 90% and the N 2 selectivity is greater than 99% in the range of 150 ~ 450 °C. It is because the redox cycle of Mn 4+ + Co 2+ ↔ Mn 3+ + Co 3+ improves the redox performance of the catalyst, which is conducive to the conduction of electrons, and then accelerates the oxidation of NO to NO 2 to produce a "fast SCR" reaction, and finally optimizes the overall SCR performance. Furthermore, the change is not significant for the catalytic activity over Mn-Co/TNU-9 in the presence of water. However, the sulfur resistance is poor at low temperatures due to the presence of ammonium bisulfate. It also has excellent catalytic stability. Therefore, supported TNU-9 catalysts will have a good development prospect in denitrification. Graphical abstract Mn-Co co-doped TNU-9 catalyst was successfully synthesized by simple ion exchange method and applied in the NH 3 -SCR. The results show that Mn-Co/TNU-9 catalyst has an excellent wide activity window in a wide temperature range of 150-450°C (NO x conversion over 90%), which is because Mn+Co 2+ ↔Mn+Co improves the redox performance and facilitates the electron transfer, which further accelerates the oxidation of NO into NO 2 that could result in the “Fast SCR” reaction. The synergistic effect between Mn and Co bimetallic can also improve activity. Moreover, Mn-Co/TNU-9 has very good catalytic stability.
研究领域:
环境科学
·
催化化学
✓ 已验证
DOI
高影响因子
DALTON TRANSACTIONS
·
2024
·Vol. 53
·期 26
·10919-10927
·
IF 3.5
Xuanzhao Lu,Baozhen Yuan,Yi Liu,Li-Xia Liu,Jun-Jie Zhu
Electrochemical reduction of carbon dioxide (CO2) or carbon monoxide (CO) to valuable multi-carbon (C2+) products like acetate is a promising approach for a sustainable energy economy. However, it is still challenging to achieve high activity and selectivity for acetate production, especially in neutral electrolytes. Herein, a bioinspired hemin/Cu hybrid catalyst was developed to enhance the surface *CO coverage for highly efficient electroreduction of CO to acetate fuels. The hemin/Cu electrocatalyst exhibits a remarkable faradaic efficiency of 45.2% for CO-to-acetate electroreduction and a high acetate partial current density of 152.3 mA cm−2. Furthermore, the developed hybrid catalyst can operate stably at 200 mA cm−2 for 14.6 hours, producing concentrated acetate aqueous solutions (0.235 M, 2.1 wt%). The results of in situ Raman spectroscopy and theoretical calculations proved that the Fe–N4 structure of hemin could enhance the CO adsorption and enrich the local concentration of CO, thereby improving C–C coupling for acetate production. In addition, compared to the unmodified Cu catalysts, the Cu catalysts functionalized with cobalt phthalocyanine with a Co–N4 structure also exhibit improved acetate performance, proving the universality of this bioinspired molecule-enhanced strategy. This work paves a new way to designing bioinspired electrolysis systems for producing specific C2+ products from CO2 or CO electroreduction.
研究领域:
电化学
·
催化材料
·
能源化学
✓ 已验证
产品关联
DOI
PubMed
高影响因子
Catalysts
·
2015
·Vol. 5
·期 2
·606-633
·
IF 2
Hongmei Qin,Xiaoshuang Qian,Tao Meng,Yi Lin,Zhen Ma
Conventional supported Pt catalysts have often been prepared by loading Pt onto commercial supports, such as SiO2, TiO2, Al2O3, and carbon. These catalysts usually have simple metal-support (i.e., Pt-SiO2) interfaces. To tune the catalytic performance of supported Pt catalysts, it is desirable to modify the metal-support interfaces by incorporating an oxide additive into the catalyst formula. Here we prepared three series of metal oxide-modified Pt catalysts (i.e., Pt/MOx/SiO2, Pt/MOx/TiO2, and Pt/MOx/Al2O3, where M = Al, Fe, Co, Cu, Zn, Ba, La) for CO oxidation. Among them, Pt/CoOx/SiO2, Pt/CoOx/TiO2, and Pt/CoOx/Al2O3showed the highest catalytic activities. Relevant samples were characterized by N2adsorption-desorption, X-ray diffraction (XRD), transmission electron microscopy (TEM), H2temperature-programmed reduction (H2-TPR), X-ray photoelectron spectroscopy (XPS), CO temperature-programmed desorption (CO-TPD), O2temperature-programmed desorption (O2-TPD), and CO2temperature-programmed desorption (CO2-TPD).Keywords:Pt catalysts;cobalt oxide;CO oxidation
研究领域:
催化化学
·
材料科学
✓ 已验证
产品关联
DOI
高影响因子
危险品化学品经营许可证（带存储）