文献检索

查找使用阿拉丁产品的科研文献

检索与阿拉丁产品相关的同行评审论文、DOI、PubMed 编号、期刊、作者、CAS 号及研究领域。

科研影响力快照

与阿拉丁产品相关的已发表科研成果

在搜索之前,这些指标可帮助访客快速了解产品关联科研的规模与质量。

347,358+ SCI 论文 与阿拉丁产品引用相关
2,303,472.95 总影响因子 匹配文献记录中影响因子的总和
81.20 最高期刊影响因子 匹配期刊中的最高 IF
6.63 平均期刊影响因子 匹配文献的平均 IF

参考指标 指标基于阿拉丁文献引用数据库及期刊影响因子记录。文献关联仅供科研参考,请以原始文献为准。

产品列表

视图 列表 网格

显示第637至648个,产品总数794个

设置提升方向
电
CHEMICAL ENGINEERING JOURNAL · 2024 · IF 13.3

Enhancement of thermoelectric performance of Cu2MnSnSe4 alloys by regulation of lattice strain

Yuqing Sun,Adeel Abbas,Hongxiang Wang,Chang Tan,Zhihao Li,Yujie Zong,Hui Sun,Chunlei Wang,Hongchao Wang

Quaternary Cu 2 MnSnSe 4 alloys with low intrinsic thermal conductivity are identified as promising middle-temperature thermoelectric materials. However, zT is depressed by the poor electrical performance. To overcome this issue, here, a series of Cu 2.1 Mn 0.9 SnSe 4 samples are prepared by ball-milling method which appears as a time-saving technique and lattice strain variation is observed by changing the annealing time ( x  = 0, 1, 2, 3, 4 days). The vacancy defects concentration of Cu, with lowest vacancy defects formation energy, is changed with the competition between compression and tension-strain state, consistent with the first principles calculations, which optimizes the carrier transport. As a result, about 4 times increment of the carrier mobility is found. Moreover, the lattice strain of several nanometers is observed with TEM analysis, which scatters phonon strongly. A lowest κ L value of 0.57 W m −1 K −1 at 673 K is obtained for  x   = 3 sample, which is close to the amorphous limit. The interactive effect of enhanced mobility and strong scattering of phonons, contributing to a record zT ∼ 0.48 at 673 K for  x   = 3 sample. Lattice strain engineering is an effective tactic to simultaneously optimize the electrical and thermal transport.

研究领域: 材料科学 · 凝聚态物理 · 功能材料 · 能源材料 · 半导体物理
✓ 已验证 DOI 高影响因子
查看原文 查看 PubMed
JOURNAL OF MOLECULAR CATALYSIS B-ENZYMATIC · 2014 · IF 2.745

Immobilization of horseradish peroxidase (HRP) on polyimide nanofibers blending with carbon nanotubes

Teng Zhang,Xiao-Ling Xu,Yi-Ning Jin,Jian Wu,Zhi-Kang Xu

Carbon nanotubes are widely applied in electronics, which offers great potential for enhancing the activity of redox enzyme. In this work, polyimide (PI) was blended with multiwalled carbon nanotubes (MWCNTs) and then electrospun into nanofibers for the immobilization of horseradish peroxidase (HRP), a redox enzyme. SEM and TEM were used to characterize the surface morphology of the PI/MWCNTs nanofibers and to analyze the protruding parts induced by the blending of MWCNT. The results indicate that, compared to the virgin PI nanofibers, the blending of MWCNTs increases the retention activity of immobilized HRP from 2.38% to 12.50%. Circular dichroism and UV–vis molecular absorption spectrometry were used to explore the interactions between HRP and MWCNTs . It seems that MWCNTs increase the enzyme activity by the facilitation of electron transfer among the catalytic intermediates “HRP I”, “HRP II” and MWCNTs.

研究领域: 生物化学 · 纳米生物技术 · 酶工程 · 生物材料 · 分析化学
✓ 已验证 DOI 高影响因子
查看原文 查看 PubMed
DYES AND PIGMENTS · 2016 · IF 4.055

Nonlinear optical properties of symmetrical and asymmetrical porphyrin derivatives with click chemistry modification

Xiong Liu,Dong Wang,Hong Gao,Zhou Yang,Yan Xing,Hui Cao,Wanli He,Huihui Wang,Jianming Gu,Huiying Hu

The novel kind of charge-transfer porphyrin complexes with symmetrical and asymmetrical side groups were synthesized by the high-yielding [2 + 2] click chemistry reaction involved a two-step procedure. Both electrochemical and UV–vis studies were characterized and proved that the side groups of the porphyrin complexes played an important role on optical properties and energy gaps. The novel series did show the narrower band gap and broader absorption in the visible and near infrared region. As the side groups, the click moieties also affected the third-order nonlinear optical responses, and all the compounds exhibited the expected nonlinear optical properties which were affected by the chemical structures . The optical-limiting performance had also been studied, which was in agreement with the result of Z-scan experiments.

研究领域: 材料化学 · 物理化学 · 光功能材料 · 有机合成 · 分子光谱学
✓ 已验证 DOI 高影响因子
查看原文 查看 PubMed
ADVANCED FUNCTIONAL MATERIALS · 2019 ·Vol. 29 ·期 38 ·1904416 · IF 15.621

Mixed-Valence-Driven Quasi-1D SnIISnIVS3 with Highly Polarization-Sensitive UV–vis–NIR Photoresponse

Huai Yang,Longfei Pan,Xiaoting Wang,Hui-Xiong Deng,Mianzeng Zhong,Ziqi Zhou,Zheng Lou,Guozhen Shen,Zhongming Wei

Mixed-valence states can bring unexpected unique phenomena, especially novel anisotropic physics, due to structural asymmetry, which originate from the discrepant distribution of atoms with different valence. This study reports an unexploited mixed-valence-driven quasi-1D Sn II Sn IV S 3 crystal, which exhibits widely and distinctively anisotropic polarized-light absorption reaching ≈3.4 from the deep ultraviolet to near-infrared region (250–850 nm). The fabricated polarization-sensitive photodetectors based on highly air-stable Sn II Sn IV S 3 nanowires display strong linear dichroism among the UV–vis–NIR spectrum with responsivity exceeding ≈150 A W −1 . Furthermore, the devices are further constructed onto a flexible polyethylene terephthalate (PET) substrate and the photoresponse remains roughly unchanged after repeated bending. This work based on novel mixed-valence-driven quasi-1D ternary sulfide Sn II Sn IV S 3 excites interest in low-symmetry semiconductors for developing broadly spectral polarization-sensitive photodetectors with environmental stability and mechanical flexibility.

研究领域: 材料科学 · 半导体物理 · 纳米光学 · 光电子学 · 凝聚态物理
✓ 已验证 DOI 高影响因子
查看原文 查看 PubMed
RSC Advances · 2017 ·Vol. 7 ·期 64 ·40462-40469 · IF 3.108

Branched PdAu nanowires with superior electrocatalytic formic acid oxidation activities

Yingxia Wang,Zhong Xiong,Yanzhi Xia

In this work, novel branched palladium–gold (PdAu) bimetallic nanowires supported on graphene (PdAu/graphene) were fabricated at relatively low temperatures for the first time by a one-pot co-reduction method with the aid of poly(diallyldimethyl-ammonium chloride). The structural characteristics of PdAu/graphene were confirmed by X-ray diffraction, X-ray photoelectron spectroscopy, transmission electron microscopy, energy-dispersive X-ray spectroscopy, high-angle annular dark-field scanning transmission electron microscopy and element mapping observations. The electrochemical properties of the PdAu/graphene were characterised by cyclic voltammetry and chronoamperometry (CA) in the formic acid oxidation reaction. Compared with a commercial Pd/C catalyst, the PdAu/graphene catalyst prepared in this work exhibited enhanced electrocatalytic activity including a higher oxidation current density, enhanced CO tolerance, and a more negative onset potential. Moreover, CA analyses demonstrated that PdAu/graphene shows higher stability than the Pd/C catalyst. The PdAu/graphene catalyst exhibited higher activity and strong poisoning resistance, which could be attributed to its special branched structure from PdAu nanowires.

研究领域: 纳米催化 · 电化学 · 材料科学 · 能源化学 · 表面科学 · 电分析化学
✓ 已验证 DOI 高影响因子
查看原文 查看 PubMed
RSC Advances · 2017 ·Vol. 7 ·期 64 ·40650-40657 · IF 3.108

One-step in situ synthesis of strontium ferrites and strontium ferrites/graphene composites as microwave absorbing materials

Wei Chen,Qingyun Liu,Xixi Zhu,Min Fu

Strontium ferrites/graphene (SrFe12O19/G) composites were synthesized by a facile one-step surfactant assisted hydrothermal method. The structure, magnetic properties and electromagnetic parameters of the as-prepared composites were evaluated. Uniform SrFe12O19 nanoparticles with a diameter of 60–70 nm were well distributed on the graphene. The formation of SrFe12O19 nanoparticles and the reduction of graphene oxide were accomplished simultaneously. The re-stacking of graphene sheets and the aggregation of SrFe12O19 nanoparticles were inhibited. The as-obtained composites exhibited better absorbing properties than the pristine SrFe12O19 particles due to the synergistic effect of SrFe12O19 and graphene. The minimum reflection loss (RL) of SrFe12O19/G composites with the thickness of 3 mm reached −34.8 dB at 13.6 GHz, and the effective absorption bandwidth (RL < −10 dB) was 5.7 GHz. However, the minimum RL of the SrFe12O19 particles only reached −13.5 dB, and the effective absorption bandwidth was 4.6 GHz. A possible mechanism for the enhanced absorbing performance was proposed.

研究领域: 材料科学 · 纳米材料 · 电磁学 · 功能材料 · 复合材料
✓ 已验证 DOI 高影响因子
查看原文 查看 PubMed
CHEMICAL ENGINEERING JOURNAL · 2024 · IF 13.3

Building a robust surface structure toward stable ultrahigh-nickel cathodes

Jingsheng Xu,Zhiyuan Wang,Runguo Zheng,Hongyu Sun,Yanguo Liu,Junhua You

Ni-rich cathodes especially with Ni content over 90 % are promising next-generation cathode materials for advanced high energy lithium − ion batteries. However, in comparison with Ni ≤ 80 % Ni-rich cathodes, these ultrahigh Ni-rich materials face more severe challenges in terms of harmful H2 − H3 phase transformations and structural degradation during cycling. Herein, we present a robust surface structure composted of defect-rich disordered structures and LiF/Li 2 SiO 3 coating for stabilizing the ultrahigh Ni-rich cathode LiNi 0.96 Co 0.03 Mn 0.01 O 2 (NCM96) by modification with (NH 4 ) 2 SiF 6 . The surface disordered structures including Li/TM mixing, spinel, and rock salt structure play a crucial role in inhibiting the irreversible H2-H3 phase transition and reducing lattice volume changes by lattice coherence effect. Moreover, the disordered surface in collaboration with the co-coating restrains the rapid growth of surface rock salt phase into the bulk, enhancing structural stability. The modified sample NSF-0.5 delivers a capacity of 238 mAh/g at 0.1C and maintains a capacity retention of 88.5 % at 0.5C after 100 cycles in half cell as well as 82.3 % at 1C after 300 cycles in full cell, significantly superior to the NCM96. The findings provide a simple and cost-effective surface modification strategy to enhance the structural stability and electrochemical performance of ultrahigh nickel cathodes for high-energy density LIBs.

研究领域: 材料科学 · 电化学 · 能源存储 · 锂离子电池 · 固态化学 · 表面工程 · 电池材料
✓ 已验证 DOI 高影响因子
查看原文 查看 PubMed
CHINESE JOURNAL OF CHEMICAL ENGINEERING · 2019 ·Vol. 27 ·期 12 ·3053-3059 · IF 1.911

Synthesis plasmonic Bi/BiVO4 photocatalysts with enhanced photocatalytic activity for degradation of tetracycline (TC)

Nianjun Kang,Dongbo Xu,Weidong Shi

In recent years, the excessive use of antibiotics has become a serious problem for human health. BiVO 4 regarded as one of the most promising visible-light-driven photocatalysts was used to degrade the antibiotics. In this paper, we fabricated Bi/BiVO 4 plasmonic photocatalysts which enhanced the photocatalytic activity of BiVO 4 for degradation of tetracycline (TC) antibiotic. The Bi/BiVO 4 photocatalysts were characterized by X-ray diffraction, X-ray photoelectron spectroscopy, scanning electron microscopy, transmission electron microscopy and high-resolution transmission electron microscopy . In addition, the photocatalytic experiment results show that the 0.04-Bi/BiVO 4 sample has the best photocatalytic activity for 2 times than the pure BiVO 4 photocatalyst. The cycle experiments, after four repetitions of the experiments, showed the sample still maintained a high photocatalytic activity. Finally, the photocatalytic reaction mechanism was also studied by free radical capture experiments and electron paramagnetic resonance spectroscopy .

研究领域: 环境化学 · 材料科学 · 光催化 · 纳米材料 · 环境污染治理 · 药物降解
✓ 已验证 DOI 高影响因子
查看原文 查看 PubMed
JOURNAL OF POWER SOURCES · 2015 · IF 6.217

A facile reflux procedure to increase active surface sites form highly active and durable supported palladium@platinum bimetallic nanodendrites

Qin Wang,Yingjun Li,Baocang Liu,Guangran Xu,Geng Zhang,Qi Zhao,Jun Zhang

A series of well-dispersed bimetallic Pd@Pt nanodendrites uniformly supported on XC-72 carbon black are fabricated by using different capping agents. These capping agents are essential for the branched morphology control. However, the surfactant adsorbed on the nanodendrites surface blocks the access of reactant molecules to the active surface sites, and the catalytic activities of these bimetallic nanodendrites are significantly restricted. Herein, a facile reflux procedure to effectively remove the capping agent molecules without significantly affecting their sizes is reported for activating supported nanocatalysts. More significantly, the structure and morphology of the nanodendrites can also be retained, enhancing the numbers of active surface sites, catalytic activity and stability toward methanol and ethanol electro-oxidation reactions. The as-obtained hot water reflux-treated Pd@Pt/C catalyst manifests superior catalytic activity and stability both in terms of surface and mass specific activities, as compared to the untreated catalysts and the commercial Pt/C and Pd/C catalysts. We anticipate that this effective and facile removal method has more general applicability to highly active nanocatalysts prepared with various surfactants, and should lead to improvements in environmental protection and energy production.

研究领域: 纳米催化 · 电化学 · 材料化学 · 能源化学 · 表面科学 · 燃料电池
✓ 已验证 DOI 高影响因子
查看原文 查看 PubMed
Journal of Materials Chemistry A · 2018 ·Vol. 6 ·期 16 ·6772-6779 · IF 9.931

Scanning laser melting for rapid and massive fabrication of filled skutterudites with high thermoelectric performance

Fan Chen,Ruiheng Liu,Zheng Yao,Yunfei Xing,Shengqiang Bai,Lidong Chen

Skutterudite-based thermoelectric materials have great potential for use in waste heat recovery, but the conventional melting–quench–annealing process is not suitable for large-scale fabrication. In this study, we developed a rapid fabrication technique that combines scanning laser melting and spark plasma sintering to synthesize bulk n-type and p-type filled skutterudites. The kinetics process and microstructure evolution during the scanning laser melting and annealing were systematically investigated. Due to fast solidification in scanning laser melting, the peritectic segregation size of precursor resultants is confined to several microns, which leads to great shortening of the fabrication period of filled skutterudites. The as-synthesized n-type and p-type filled skutterudites achieve excellent dimensionless figures of merit: ZT ∼ 1.23 at 850 K for Yb0.4Co4Sb12.1; ZT ∼ 1.09 at 700 K for In0.5Co4Sb12.1; ZT ∼ 0.79 at 750 K for Ce0.95Fe3CoSb12.1, which are among the highest values of single filled skutterudites. The shortened processing period and enhanced thermoelectric performance make this novel synthesis method suitable for industrial-level large-scale fabrication of skutterudite-based thermoelectric materials.

研究领域: 材料科学 · 热电材料 · 金属学与冶金工程 · 固态物理 · 先进制造技术
✓ 已验证 DOI 高影响因子
查看原文 查看 PubMed
Advanced Optical Materials · 2016 ·Vol. 4 ·期 11 ·1829-1837 · IF 5.359

20-mm-Large Single-Crystalline Formamidinium-Perovskite Wafer for Mass Production of Integrated Photodetectors

Yucheng Liu,Jiankun Sun,Zhou Yang,Dong Yang,Xiaodong Ren,Hua Xu,Zupei Yang,Shengzhong (Frank) Liu

CH 3 NH 3 PbX 3 (MAPbX 3 )-based perovskite has attracted tremendous research efforts in the last few years. With the discovery that the HC(NH 2 ) 2 PbI 3 (FAPbI 3 ) perovskite offers even higher solar cell efficiency, better thermal stability, and broader optical absorption, it is expected that it will provide more excitement in optoelectronic applications including laser, LED, photodetector, etc. The development in preparing large Single-Crystalline Formamidinium-Perovskite FAPbI 3 using the inverse-temperature reactive crystallization process, and associated wafer-slicing process is presented. The availability of the large Single-Crystalline Formamidinium-Perovskite Wafer makes it possible to fabricate integrated circuits. An array of 153 photodetectors on a piece of thin wafer, demonstrating feasibility of mass production of integrated circuits on the perovskite wafer is designed and prepared. It is found that the wafer-based photodetector shows much superior performance, with 90 times higher photoresponse and broader optical absorption than its thin-film perovskite counterpart.

研究领域: 材料科学 · 半导体物理 · 光电子学 · 晶体生长 · 器件 fabrication
✓ 已验证 DOI 高影响因子
查看原文 查看 PubMed
COLLOIDS AND SURFACES A-PHYSICOCHEMICAL AND ENGINEERING ASPECTS · 2019 · IF 3.131

The effect of magnetic field on the hydration of cation in solution revealed by THz spectroscopy and MDs

Yanqi Gu,Shayu Li,Yuehong Xu,Jiaguang Han,Miao Gu,Zhipeng Cai,Yan lv,Guoxin Xie,Tianbao Ma,Jianbin Luo

The influence of an external magnetic field on the picosecond network dynamics of the salt (KCl) solution is investigated by terahertz time-domain spectroscopy. Because hydration changes the motions of water molecules clusters, we test hydration by measuring the change of dielectric loss caused by the slow relaxation of water molecules clusters. We find experimentally that the magnetic field enhances the number of water molecules involved in hydration and the radius of dynamic hydration layer in salt solutions. However, with the increasing concentration, there is a downward in the hydration enhancement per equivalent. Meanwhile, the simulated results show the number of water molecules in hydration layers increases which is consistent with our experimental results. Besides, the simulation reveals that external magnetic field mainly affects the second hydration layer and the stability of water molecules network in hydration layer is enhanced with external magnetic field .

研究领域: 物理化学 · 生物物理 · 分子生物学 · 光谱学 · 溶液化学
✓ 已验证 DOI 高影响因子
查看原文 查看 PubMed
已复制

文献关联基于可获得的产品、CAS、DOI 及引用记录。收录不代表作者或出版方对阿拉丁产品的背书,请以原始文献为准。