JOURNAL OF CHEMICAL AND ENGINEERING DATA
·
2022
·
IF 3.119
Song Lin,Yufan Pang,Jingwei Cao,Yueyang Jiang,Houchun Yan,Qingsong Li
For the separation of 2,2,2-trifluoroethanol in water, two alcohols and two ketones were chosen as extractants for experiments at 101.3 kPa and 298.2 K. The liquid–liquid equilibrium data for water + 2,2,2-trifluoroethanol + (4-methyl-2-pentanol, methyl isobutyl ketone, methyl isopropyl ketone, and benzyl alcohol) were measured under these conditions. The separation effects of the four solvents were assessed by the distribution coefficient (D) and the separation factor (S). Meantime, the interaction parameters were obtained by fitting the experimental data using NRTL and UNIQUAC models, and both values of AAD and rmsd were less than 0.43%. The GUI-MATLAB series of topological analysis tools were used to check the accuracy of the measured values with the binary interaction parameters.
研究领域:
化学工程
·
热力学
·
分离科学
✓ 已验证
DOI
高影响因子
JOURNAL OF CHEMICAL AND ENGINEERING DATA
·
2014
·
IF 2.045
Qi Zhang,Yonghong Hu,Ying Shi,Yang Yang,Limin Cheng,Cuicui Cao,Wenge Yang
Data on corresponding solid–liquid equilibrium of dibenzothiophene (DBT) in different solvents are essential for a preliminary study of industrial applications. In this study, the solubility behavior of DBT in different solvents, such as methanol, ethanol, isopropyl alcohol, butan-1-ol, formic acid, and acetonitrile at temperatures ranging from (278.15 to 328.15) K was investigated. An analytical stirred-flask method was employed to measure the dissolubility of DBT. For the temperature range investigated, the solubility of dibenzothiophene in the solvents increased with increasing temperature. The thermodynamic models, such as the Van ‘t Hoff model, the modified Apelblat model and the Buchowski–Ksiazaczak λh model were investigated to describe the experimental data. It was found that the modified Apelblat model was the most suitable for predicting the solubility behavior of DBT with a temperature increment. The calculated thermodynamic parameters indicated that in each studied solvent the dissolution process of DBT is endothermic.
研究领域:
化学热力学
·
溶解度工程
·
分离过程
·
物理化学
✓ 已验证
DOI
高影响因子
ACS Applied Energy Materials
·
2023
·
IF 6.4
Mengcheng Zhou,Hongxia Chen,Shuangwu Xu,Xinyu Zhang,Rihuang Nie,Cheng Li,Yutian Yang,Hongming Zhou
O3-type layered oxide materials are regarded as the most application-prospective cathode materials for sodium-ion batteries owing to the high theoretical specific capacity and good full-cell matching. However, there are still problems, such as poor rate performance and low available specific capacity. In this paper, we propose to overcome the above-mentioned problems by using K to replace the Na sites of O3-NaNi0.5Mn0.3Ti0.2O2 materials. A series of K-doped materials, KxNa1–xNi0.5Mn0.3Ti0.2 (x = 0, 0.025, 0.05, 0.075), were successfully synthesized. When the doping amount is 0.05, the available specific capacity and rate performance are significantly improved. The K0.05Na0.95Ni0.5Mn0.3Ti0.2 sample exhibits an initial discharge specific capacity of 151.6 mAh g–1 at 0.1C (1C = 200 mA g–1), in the voltage window of 2.0–4.2 V, while the pristine one only delivers 135.8 mAh g–1 at 0.1C. It still delivers an initial discharge specific capacity of 119.8 mAh g–1 at 5C and 70.2 mAh g–1 after 200 cycles, while the pristine one only has a specific capacity of 36 mAh g–1 after 200 cycles. The X-ray diffraction (XRD), transmission electron microscopy (TEM), X-ray photoelectron spectroscopy (XPS), electrochemical impedance spectroscopy (EIS), and galvanostatic intermittent titration technique (GITT) tests were conducted to investigate the effect of different K doping amounts on the crystal structure and electrochemical properties. The results indicate that the expanded Na layer spacing and improved Na+ diffusion coefficient are the primary reasons for the improved electrochemical properties. This finding could provide insights into improving the rate performance and available specific capacity of the O3-type layered oxide materials.
✓ 已验证
产品关联
DOI
高影响因子
Advanced Healthcare Materials
·
2023
·
IF 10
Panqin Ma,Zheng Luo,Zhiguo Li,Yuchao Lin,Zibiao Li,Zhen Wu,Changliang Ren,Yun-Long Wu
Mitochondrial potassium ion channels have become a promising target for cancer therapy. However, in malignant tumors, their low expression or inhibitory regulation typically leads to undesired cancer therapy, or even induces drug resistance. Herein, this work develops an in situ mitochondria-targeted artificial K + channel construction strategy, with the purpose to trigger cancer cell apoptosis by impairing mitochondrial ion homeostasis. Considering the fact that cancer cells have a lower membrane potential than that of normal cells, this strategy can selectively deliver artificial K + channel molecule 5F8 to the mitochondria of cancer cells, by using a mitochondria-targeting triphenylphosphine (TPP) modified block polymer (MPTPP) as a carrier. More importantly, 5F8 can further specifically form a K + -selective ion channel through the directional assembly of crown ethers on the mitochondrial membrane, thereby inducing mitochondrial K + influx and disrupting ions homeostasis. Thanks to this design, mitochondrial dysfunction, including decreased mitochondrial membrane potential, reduced adenosine triphosphate (ATP) synthesis, downregulated antiapoptotic BCL-2 and MCL-1 protein levels, and increased reactive oxygen species (ROS) levels, can further effectively induce the programmed apoptosis of multidrug-resistant cancer cells, no matter in case of pump or nonpump dependent drug resistance. In short, this mitochondria-targeted artificial K + -selective ion channel construction strategy may be beneficial for potential drug resistance cancer therapy.
✓ 已验证
产品关联
DOI
PubMed
高影响因子
INDUSTRIAL & ENGINEERING CHEMISTRY RESEARCH
·
2023
·
IF 4.2
Qiongqiong Luo,Jinshun Lei,Ziyu Zhuang,Dewen Zeng
The solubility data of the MgF2–MnF2–MnSO4–H2O quaternary system and its subsystems are crucial for the removal of magnesium ions from a MnSO4 aqueous solution as the MgF2 precipitate. However, these data recorded at 298.15 K have not been reported, except for the MnF2–MnSO4–H2O system. In this study, the solubility isotherms of the MgF2–MnF2–H2O, MgF2–MnSO4–H2O, and MgF2–MnF2–MnSO4–H2O systems at 298.15 K and MnF2 solubility in pure water at various temperatures were systematically measured. The results show that MgF2 solubility initially decreases sharply followed by a gradual decrease as the MnF2 concentration increases. MgF2 solubility rises with increasing MnSO4 concentration in pure MnSO4 and the MnF2-saturated MnSO4 aqueous solution. MgF2 solubility in the MnF2-saturated MnSO4 aqueous solution decreases to 2.3–6.5% of its value in the pure MnSO4 aqueous solution at a certain MnSO4 concentration. MnF2 solubility increases with increasing temperatures in the MnF2–H2O system. A Pitzer–Simonson–Clegg model incorporated in the ISLEC software was used to simulate and predict the solubility curves of the MgF2–MnF2–MnSO4–H2O quaternary system and its subsystems. The model satisfactorily represented the solubility data of the subbinary and subternary systems of the MgF2–MnF2–MnSO4–H2O quaternary system within the analysis error, except for the solubility isotherms of the Mg(Mn)SO4·7H2O, Mg(Mn)SO4·4H2O, and Mg(Mn)SO4·H2O solid solutions. The predicted solubility data of the MgF2–MnSO4–H2O system at 298.15 K agree well with the experimental data with a slight deviation of the MgF2–MnF2–MnSO4–H2O system. Based on the established model, the variation of MgF2 solubility curves with the addition of anhydrous MnF2 in MnSO4 aqueous solutions at different concentrations was predicted. The study provides theoretical guidance for removing magnesium ions from a MnSO4 aqueous solution via MgF2 precipitation.
✓ 已验证
产品关联
DOI
高影响因子
INORGANIC CHEMISTRY
·
2023
·
IF 4.6
Jingfang Zhou,Pifu Gong,Mingjun Xia,Aimin Ji,Lifang Zhang,Huiqiang Wu,Qian Wu
Replacing alkali metals (K, Na atoms) by an alkaline-earth metal (Ba atom), α-Ba3Sc2(BO3)4 (high-temperature phase) is successfully obtained by a molten salt method, taking Ba2K1.6Na0.4Sc2(BO3)4 as the parent template. Although both of them exhibit similar layered structures composed of ScO6 and BO3 units, α-Ba3Sc2(BO3)4 shows largely distorted ScO6 octahedra (Δd = 0.56) forced by the uniform tension of a larger space effect from BaO12 polyhedrons, rather than regular ScO6 octahedra like in Ba2K1.6Na0.4Sc2(BO3)4. Experimental measurements and calculated analyses elucidate that distorted ScO6 octahedra in α-Ba3Sc2(BO3)4, displaying a second-order Jahn–Teller (SOJT) effect, enlarge the experimental birefringence up to 0.14@550 nm, while Ba2K1.6Na0.4Sc2(BO3)4 with regular ScO6 octahedra only shows Δn = 0.11 under the same condition. In addition, other optical and thermal properties of the two title compounds were characterized. The experimental results indicate that Ba2K1.6Na0.4Sc2(BO3)4 and α-Ba3Sc2(BO3)4 are promising birefringent materials.
✓ 已验证
产品关联
DOI
PubMed
高影响因子
Catalysts
·
2023
·Vol. 13
·期 2
·450
·
IF 3.9
Muhammad Naeem Younis,Zhiheng Ren,Chunshan Li,Erqiang Wang,Jie Li
The advancing effects of various alkali and alkaline earth metals (inclusive of K, Ca, and Sr) modified Cu/SiO2catalysts, prepared with a modified precipitation-gel method, were investigated for the production of ethanol via hydrogenation of methyl acetate. Our results showed that Sr-doped catalysts exhibited the best and most consistent results during catalytic tests. A series of techniques, including X-ray diffraction technique, Raman spectroscopy, N2adsorption/desorption, N2O titration method, FTIR spectroscopy, and H2temperature, programmed desorption and reduction (TPD and TPR), and X-ray Photoelectron Spectroscopy, which was used to check the detailed characterization of Sr modification in the catalyst and its structural impacts on the properties of the catalyst. These results demonstrated that the addition of 5%Sr could strengthen the intrinsic stability of the catalyst by formulating the appropriate ratio of Cu+/(Cu0+ Cu+) to facilitate catalytic outcome improvement. The addition of 5%Sr-30%Cu/SiO2under the most favorable conditions, resulting in the peak conversion of MA (95%) and ethanol selectivity (96%), indicates its magnificent catalytic stabilizing effects. Furthermore, the best performing catalyst was compared and tested under various conditions (LHSV and temperatures) and a 300 h long life run.Keywords:hydrogenation;methyl acetate;ethanol;strontium
✓ 已验证
产品关联
DOI
高影响因子
JOURNAL OF CHEMICAL AND ENGINEERING DATA
·
2019
·
IF 2.298
Rui-Zhi Cui,Wu Li,Ya-Ping Dong
The phase equilibria relationship between the quaternary system LiCl–KCl–Li2SO4–K2SO4–H2O and its subsystems LiCl–KCl–H2O and LiCl–Li2SO4–H2O was studied by the isothermal dissolution equilibrium method at 288.15 K, and the corresponding phase diagrams were drawn. At 288.15 K, ternary systems LiCl–KCl–H2O and LiCl–Li2SO4–H2O all belong to the simple type. In the phase diagram of the quaternary system LiCl–KCl–Li2SO4–K2SO4–H2O, there are five equilibrium solid phase crystallization fields: LiCl·2H2O, KCl, Li2SO4·H2O, K2SO4, and Li2SO4·K2SO4. Compared with the multitemperature phase diagrams of this system at 288.15–348.15 K, it was found that the basic configuration of the phase diagrams is the same. As the temperature increased, the phase region of double salt Li2SO4·K2SO4 clearly increased, whereas the phase region of single salt KCl and K2SO4 clearly decreased. On the basis of the experiment, the extended Harvie–Weare model of the Pitzer model was used to predict the solubility data of the quaternary system. The simulated and measured values were basically in good agreement.
✓ 已验证
产品关联
DOI
高影响因子
ELECTROCHIMICA ACTA
·
2018
·
IF 5.116
Jiangping Jing,Zhuoyuan Chen,Chang Feng
Graphitic carbon nitride (g-C 3 N 4 ) usually shows amphoteric property in a neutral solution. In this work, a K&I co-doped g-C 3 N 4 is prepared by simply sintering the mixture of dicyandiamine, KI and I 2 . The K&I co-doping modulates the band structure of g-C 3 N 4 with pulling the Fermi level toward its conduction band minimum. The obtained K&I co-doped g-C 3 N 4 (K&I-C 3 N 4 ) generates positive photocurrents over the whole investigated potential range, exhibiting a typical n-type semiconductor characteristic. Therefore, the K&I co-doping transforms the g-C 3 N 4 from amphoteric to n-type semiconductor. Also, the prepared K&I-C 3 N 4 shows widened light absorption range and enhanced separation efficiency of the photogenerated charge carriers, which results in the dramatically enhanced photoelectrochemical performance.
✓ 已验证
DOI
高影响因子
ORGANIC ELECTRONICS
·
2018
·
IF 3.68
Chuan Wang,Wu Tang,Zeyi Yao,Yongzhen Chen,Jingfang Pei,Cong Fan
Terephthalic acid (H 2 TP) is initially unveiled to be the first example of organic anodes exhibiting the universal Li-ion, Na-ion and K-ion storage capabilities. In Li-ion half cells, H 2 TP can deliver the average capacities of ∼235 mAh g −1 for 500 cycles; In Na-ion half cells, H 2 TP is reported to deliver the average capacities of ∼200 mAh g −1 for 50 cycles; and in K-ion half cells, H 2 TP can exhibit the average capacities of ∼240 mAh g −1 for 150 cycles. At the same time, the chemical structure and crystal structure of H 2 TP could be transformed into its related metal salts on the anode side due to the low reduction potential. This work indicates that organic electrode materials should own the universal metal-ion-storage (e.g., Li + , Na + , K + , etc.) capability for their large void room of organic solid/crystal state.
✓ 已验证
产品关联
DOI
高影响因子
JOURNAL OF CHEMICAL AND ENGINEERING DATA
·
2018
·
IF 2.196
Chao Guo,Yangtong Tan,Yu Qian,Siyu Yang
Experimental liquid–liquid equilibria (LLE) data for ternary (methyl propyl ketone + hydroquinone + water) and (methyl propyl ketone + resorcinol + water) systems were determined under atmospheric pressure at T = 298.15, 318.15, and 333.15 K. Distribution coefficients and separation factors were calculated to evaluate extraction effectiveness. Hand, Bachman, and Othmer–Tobias equations were utilized to confirm consistency of experimental LLE data. Thermodynamic NRTL and UNIQUAC models were used to correlate experimental LLE data, and corresponding binary interaction parameters were obtained. The estimated data from the two models agree well with experimental LLE data. The NRTL model gives a better agreement than the UNIQUAC model for ternary (methyl propyl ketone + hydroquinone or resorcinol + water) systems.
✓ 已验证
产品关联
DOI
高影响因子
JOURNAL OF CHEMICAL AND ENGINEERING DATA
·
2018
·
IF 2.196
Yangtong Tan,Chao Guo,Yu Qian,Siyu Yang
Liquid–liquid equilibrium (LLE) data for the ternary system of (2-pentanone + catechol + water) and (mesityl oxide + catechol + water) was measured under atmospheric pressure at T = (298.2, 318.2 and 333.2) K. The distribution coefficients and separation factors were employed to assess the efficiency of extracting catechol from water. The nonrandom two liquid and universal quasichemical models were applied to correlate the LLE data, and the corresponding binary interaction parameters were obtained. The topological analysis of LLE correlation was used to confirm that the parameters satisfy the Gibbs stability criteria.
✓ 已验证
产品关联
DOI
高影响因子
危险品化学品经营许可证（带存储）