CRYSTAL GROWTH & DESIGN
·
2024
·
IF 3.2
Pengju Xia,Yifeng Lei,Wanyuan Li,Kaiting Wu,Chengyu Ni,Man Xu,Wubin Dai
With the growing public awareness of protecting vision and prevention of hazardous effects, there is much-needed research on a “healthy” full visible spectrum under near-ultraviolet (nUV) excitation in phosphor-converted white light-emitting diodes (pc-wLEDs) to fill the “cyan gap” and avoid employing a blue LED chip. Herein, a novel series of borosilicates Ba2CaB2Si4O14 (BCBS): Ce3+/Tb3+/Sm3+/Sr2+/Na+ phosphors, presenting color-tunable photoluminescence (PL), high quantum yield (QY), and thermal stability, were designed and synthesized via a facile solid-phase reaction. The Rietveld analyses, density functional theory (DFT) simulations, and theoretical calculations of bond energy together imply the site occupations of Ce/Tb/Sm on Ba2+/Ca2+ sites with a preferred location on Ca2+ over the Ba2+ site. The broad/bright cyan-PL from BCBS: Ce under nUV excitation is associated with the allowed f–d transitions of Ce3+ and dual-site occupancies. The forbidden f–f transitions of both the green-PL of Tb and the red-PL of Sm were insensitive to the site environment and helpful to PL color regulation. The cascading Ce → Tb → Sm energy transfer is confirmed, where Tb is regarded as an energy transfer (ET) bridge to avoid the metal–metal charge transfer (MMCT) effect. The introduction of Na+ as both flux and charge compensator is for the sake of decreasing defects from heterovalent substitutions and regulating morphology. Further incorporation of Sr2+ is to modulate the lattice environments of dopants for controlling the shift of PL. Finally, as a proof-of-concept implement, a pc-wLED assembled by BCBS: Ce/Tb/Sm/Sr/Na and an nUV LED chip via a remote “capping” packaging strategy show attractive performance.
✓ 已验证
产品关联
DOI
高影响因子
CHEMICAL ENGINEERING JOURNAL
·
2025
·
IF 13.2
Zhijie Zhang,Yilin Zhou,Xiaodong Zhang,Jixian Ma,Miaoning Yao,Jie Sun,Tong He,Xuexia He,Zhibin Lei,Ruibin Jiang,Zong-huai Liu,Qi Li
Na-rich manganese-based layered oxide cathodes have presented potential applications in high energy–density sodium-ion batteries due to their cost-effectiveness and large theoretical specific capacity. However, the low kinetics of anionic redox reaction and lattice distortion caused by the Mn 3+ Jahn-teller effect greatly hindered the actual capacity, rate, and cycling performances of these cathodes. Herein, a Li + substitution induced O3/O′3 biphasic tailoring strategy has been proposed for constructing the Na-rich NaLi 0.2 Mn 0.8 O 2 (NLMO) cathode. Compared with conventional O′3-Na 1.2 Mn 0.8 O 2 (NMO) cathode, the O3/O′3-NLMO cathode enabled to provide an ultrahigh capacity of 233 mAh g −1 , superior capacity retention of 86 % after 50 cycles, and outstanding rate performance with the recorded-up capacity of 165 mAh g −1 at a high current density of 200 mA g −1 . In addition, NLMO also displayed rapid Na + -diffusion and more structural reversibility of O3/O′3-P3-O1-P3-O3/O′3 during the entire charging and discharging processes. The above excellent performances of NLMO cathode could be attributed to the well-designed O3/O′3 biphasic structure that provides the synergistic function of drastically enhancing reaction kinetics of anionic (O − /O 2– ) couple and efficiently alleviating multiphase transitions caused by Mn 4+ /Mn 3+ cationic couple. This unique finding of Li + substitution induced biphasic structure provides an insight for developing economical and high-performance Na-rich oxide cathodes.
✓ 已验证
产品关联
DOI
高影响因子
INORGANIC CHEMISTRY COMMUNICATIONS
·
2024
·
IF 4.4
Houteng Zhao,Yilian Ran,Xiya Miao,Siyu Cheng,Dongze Li,Yufeng Du,Xiang Liu,Ruijin Yu
A series of novel phosphors, doping Eu 3+ and Na + ions in the Sr 3 MgNb 2 O 9 (SMNO) crystal lattice (SMNO: x Eu 3+ , x Na + , x = 0.5–30 mol%), was successfully synthesized through high-temperature solid-state reaction. X-ray diffraction (XRD) analysis and Rietveld refinement confirmed the successful synthesis of SMNO:Eu 3+ , Na + . The phosphor belongs to the hexagonal crystal system and the P 3 ¯ m 1 (No.164) space group. The bandgap energy of SMNO was calculated with Materials Studio and measured with the use of diffuse reflectance spectroscopy. The excitation spectrum of SMNO:Eu 3+ , Na + displays multiple narrow absorption peaks in the violet-blue region as well as a charge transfer band (CTB) near 300 nm, exhibiting the highest peak at 394 nm. Four distinct characteristic peaks are observed in the emission spectrum of SMNO:Eu 3+ , Na + . Notably, the peak at 601 nm shows the highest emission intensity due to the radiative transition from 5 D 0 → 7 F 2 . By varying doping concentrations, it was determined that an optimal concentration of 5 mol%Eu 3+ resulted in phosphors, with high color purity exceeding 99 %. Concentration quenching is attributed to the nearest neighbor ions interaction. Furthermore, SMNO:Eu 3+ , Na + exhibited good stability in 300–480 K, with luminescent intensity remaining 68.6 % at 420 K and 54.4 % at 480 K compared to room temperature (300 K). The internal quantum efficiency (IQE) of SMNO:5%Eu 3+ , 5 %Na + is 65.0 %. Both red and white light-emitting diodes (LEDs) were prepared using SMNO:Eu 3+ , Na + . The chromaticity coordinates of w-LED were measured as (0.357, 0.376), correlating to a correlated color temperature (CCT) of 4685 K and exhibiting a good color rendering index (CRI, R a = 88). Additionally, the latent fingerprint (LFP) development demonstrated clear visualization of Levels I-III characteristic structures of fingerprints when utilizing SMNO:Eu 3+ , Na + . These findings suggest promising applications for SMNO:Eu 3+ , Na + in w-LED lighting and LFP development.
✓ 已验证
产品关联
DOI
高影响因子
Food Packaging and Shelf Life
·
2025
·
IF 10.6
Yanqing Li,Xuchen Li,Shaomei Li,Jiao Li,Xiang Zou,Hongwei Zhan,Guanyuan Qu,Lixiu Zhang,Yongjun Sun,Wenming Ju,Mengqi Ye,Pengdong Sun,Jingyuan Li,Yang Deng,Ting Ding
Aeromonas sobria , recognized as a psychrotrophic specific spoilage organism in refrigerated aquatic products, facilitates its proliferation by metabolizing proteins, lipids, and carbohydrates, thereby generating spoilage-associated metabolites and compromising product quality. Quorum sensing (QS), a bacterial cell-to-cell communication mechanism, orchestrates the secretion of virulence and spoilage factors in A. sobria via the LuxI/R QS system. Targeting this regulatory pathway presents a novel strategy to mitigate spoilage and extend the shelf life of aquatic products. Previous studies have demonstrated that zingerone (ZRN) exhibits quorum-quenching activity at sub-inhibitory concentrations; however, its practical application is constrained by limited solubility and bioavailability. To overcome these challenges, ZRN was encapsulated within halloysite nanotubes (HNTs) and incorporated into a self-assembled composite film composed of chitosan (CS) and sodium carboxymethyl cellulose (CMC-Na). The fabricated film was characterized for its structural, thermal, and mechanical properties and subsequently evaluated for its preservation efficacy on refrigerated perch fillets. The composite film exhibited a homogeneous surface morphology with uniformly dispersed HNTs, alongside adequate thermal stability, tensile strength, and physicochemical attributes suitable for refrigerated aquatic product preservation. Notably, the film suppressed spoilage indicators, including total volatile basic nitrogen (TVB-N) accumulation, lipid peroxidation, and bacterial spoilage potential, without inhibiting A. sobria growth. Furthermore, it mitigated muscle tissue degradation and biogenic amine formation in perch fillets during refrigerated storage. Molecular docking simulations revealed that ZRN competitively binds to the LuxR-type receptor at the same binding pocket as the endogenous autoinducer C 4 -HSL, thereby disrupting QS signaling. Collectively, this ZRN-loaded composite film represents a promising biodegradable packaging solution for enhancing the quality and shelf life of refrigerated aquatic foods.
✓ 已验证
产品关联
DOI
高影响因子
JOURNAL OF SUPERCRITICAL FLUIDS
·
2025
·
IF 4.4
Peng Feng,Donghai Xu,Kunkun Song,Gang Yin,Guanyu Jiang,Yang Yang,Yaling He
Supercritical water oxidation efficiently degrades organic waste but faces challenges from salt deposition due to the low solubilities of salts in supercritical water (SCW). This study investigated the characteristics and mechanisms of dissolution and deposition of mixed sulfate and chloride salts in SCW. At low water densities the common ion effect was observed in Na 2 SO 4 /K 2 SO 4 mixtures. Na + tended to occupy the junctions between SO 4 2- , while K + tended to occupy the cluster endings. Due to the weaker electrostatic interaction between K + (with larger ionic radius) and SO 4 2- , large and medium-sized clusters were more prone to decomposition in K + -rich solutions. K 2 SO 4 induced a “salting-in” effect on Na 2 SO 4 , whereas Na 2 SO 4 exerted a “salting-out” effect on K 2 SO 4 at high water densities. Both sulfates exhibited heterogeneous nucleation, depositing on heated sidewalls as nucleation sites, with Na 2 SO 4 proving more difficult to remove than K 2 SO 4 . In KCl/Na 2 SO 4 mixtures, homogeneously nucleated chloride salts created many preferential nucleation sites for Na 2 SO 4 deposition.
✓ 已验证
产品关联
DOI
高影响因子
Journal of Materials Chemistry A
·
2015
·Vol. 3
·期 11
·5820-5828
·
IF 7.443
N. Li,S. Liao,Y. Sun,H. W. Song,C. X. Wang
Large volume changes cause a series of complicated problems in alloy-type anodes, such as pulverization, exfoliation and the capacity decay which results. Therefore, solutions for the problems caused by large volume changes in sodium ion battery (SIB) anodes are urgently needed. Herein, we report a novel route to encapsulate Sb2O3/Sb nanoparticles (Sb2O3/Sb-NPs) within a graphene shell nanostructure (Sb2O3/Sb@graphene) via microwave plasma irradiation of Sb(CH3COO)3 and a subsequent graphene growth procedure. The designed structure, Sb2O3/Sb@graphene NPs anchored on carbon sheet networks (CSNs), provides an ultra-thin, flexible graphene shell to accommodate the volume changes of Sb2O3/Sb, and thus demonstrates excellent cycling stability (92.7% of the desodiation capacity was retained after 275 cycles), a long cycle life (more than 330 cycles) and a good rate capability (220.8 mA h g−1 even at 5 A g−1). The stability could be compared to that of commercial graphite in lithium ion batteries.
✓ 已验证
DOI
高影响因子
CERAMICS INTERNATIONAL
·
2024
·
IF 5.1
Halizati Abulimiti,Aierken Sidike,He Jiuyang
Highly efficient blue-cyan phosphors can fill the cyan gap in conventional white light-emitting diode (LED) devices to improve the spectral continuity while effectively increasing the white LED colour rendering index (Ra). In this study, Ba 0·94 Al 2- x Ga x Si 2 O 8 :0.06Ce 3+ , M + (Li, Na, K, x = 0–0.8) blue-cyan phosphors with a feldspar structure were prepared by a high-temperature solid-phase method using charge compensation and cation substitution strategies. The barium (Ba) vacancy due to the charge-imbalance substitution of Ce 3+ is compensated by the different charge compensators Li + , Na + , and K + . The charge compensators affect the luminescence performance of the samples, with the K + -compensated samples showing the greatest enhancement, with intensities up to 1.8 times that of the uncompensated samples. The cation substitution strategy using Ga 3+ to partially replace Al 3+ further improves the luminescence performance of the Ba 0·94 Al 2 Si 2 O 8 :0.06Ce 3+ , 0.04 K + sample, and the excitation band is also improved. In this case, the luminescence intensity of the Ba 0·94 Al 2 Si 2 O 8 :0.06Ce 3+ luminescent material is increased by a factor of 6, and a broadband blue-cyan phosphor with a full-width at half-maximum of 118 nm containing blue, cyan and green is obtained. The co-doping of charge compensators and partial cation substitution improved the luminescence performance of phosphors. The representative sample Ba 0·94 Al 1.6 Ga 0.4 Si 2 O 8 :0.06Ce 3+ , 0.04 K + has a luminescence intensity at a temperature of 150 °C that is 83.2% of that at room temperature and good thermal stability . The combination of 365 nm near-ultraviolet (NUV) LED chips with Ba 0·94 Al 1.6 Ga 0.4 Si 2 O 8 :0.06Ce 3+ , 0.04 K + and the commercial red powder (Ca, Sr)AlSiN 3 :Eu 2+ yields a white LED device with an Ra of up to 93 and a correlated colour temperature (CCT) of 4825 K. These results show that the blue-cyan phosphor complements the cyan component while simplifying the manufacturing process of white LEDs.
✓ 已验证
DOI
高影响因子
CRYSTENGCOMM
·
2016
·Vol. 18
·期 9
·1655-1664
·
IF 3.849
Dong Yan,Chun-Li Hu,Jiang-Gao Mao
Four new alkali metal boroantimonates, namely, A2SbB3O8 (A = Na, K, Rb) and β-RbSbB2O6, have been synthesized by high-temperature solid-state reactions. Isostructural A2SbB3O8 (A = Na, K, Rb) crystallizes in the monoclinic space group P21/c, with structures featuring a novel 3D anionic framework composed of SbO6 octahedra and linear B3O8 groups with 1D tunnels of Sb4B4 8-membered-rings (MRs) along the a-axis, which are filled by alkali metal ions. β-RbSbB2O6 crystallizes in the polar space group Cc, revealing novel 3D anionic networks composed of SbO6 octahedra chains and B2O5 groups with 1D tunnels of Sb4B2 6-MRs along the b-axis and 1D tunnels of Sb3B4 7-MRs along the c-axis. Studies on their optical properties and thermal stability, band structure calculations based on DFT methods and linear optical calculations have also been performed.
✓ 已验证
DOI
高影响因子
CHEMICAL ENGINEERING JOURNAL
·
2017
·
IF 6.216
Ke Wang,Ying Huang,Xiulan Qin,Mingyue Wang,Xu Sun,Meng Yu
A novel graphene/carbon nanotube (GN-CNT) hybrid was synthesized by thermal pyrolysis of urea on the surface of graphene at 800, 900 and 1000 °C. The effects of pyrolysis temperature on yield of carbon nanotubes and electrochemical properties of the GN-CNT hybrid were investigated carefully. The production rate of pyrolysis gas was increased as temperature rising. The GN-CNT hybrid reached the largest surface area and the generation of a mass of pores at the pyrolysis temperature of 900 °C due to the carbon nanotubes cracking during pyrolysis at 1000 °C. The properties of favorable 3D architecture, the generation of a mass of pores during the release of carbon nitride gases and outstanding mechanical flexibility, showed pronounced effects on the fast and steady transfer of electrons and sodium-ion. Consequently, the GN-CNT hybrid pyrolysized at 900 °C exhibit a very high reversible capacity of up to 269.14 mAh g −1 after 100 cycles at a current density of 300 mA g −1 . Even up to 5 A g −1 , a rate capacity of 195.37 mA h g −1 can be obtained after 700 cycles.
✓ 已验证
DOI
高影响因子
ACS Applied Materials & Interfaces
·
2017
·
IF 7.504
Chenxiao Chu,Jing Yang,Qianqian Zhang,Nana Wang,Feier Niu,Xuena Xu,Jian Yang,Weiliu Fan,Yitai Qian
Flower-like assembly of ultrathin nanosheets composed of anatase and bronze TiO2 embedded in carbon is successfully synthesized by a simple solvothermal reaction, followed with a high-temperature annealing. As an anode material in sodium-ion batteries, this composite exhibits outstanding electrochemical performances. It delivers a reversible capacity of 120 mA h g–1 over 6000 cycles at 10 C. Even at 100 C, there is still a capacity of 104 mA h g–1. Besides carbon matrix and hierarchical structure, abundant interfaces between anatase and bronze greatly enhance the performance by offering additional sites for reversible Na+ storage and improving the charge-transfer kinetics. The interface enhancements are confirmed by discharge/charge profiles, rate performances, electrochemical impedance spectra, and first-principle calculations. These results offer a new pathway to upgrade the performances of anode materials in sodium-ion batteries.
✓ 已验证
DOI
高影响因子
ACS Applied Energy Materials
·
2025
·
IF 5.5
Hongjie Chen,Yixuan Su,Yucong Chen,Minghan Bao,Mingjun Wu,Junyang Chen,Weitao Chen,Qiang Ru
The inherent low electronic conductivity of NASICON-type Na4MnV(PO4)3 (NMVP) impedes its use in advanced energy storage. Herein, we address this challenge by introducing a citric acid-derived carbon coating to elevate the material’s conductivity and electrochemical performance. By precisely tailoring the configuration of the carbon layer, we fabricated Na4MnV(PO4)3 encapsulated by a carbon coating (NMVP@C) and constructed a 3D hierarchical architecture with incorporated V(III) and Mn(II) states, which prompts the reversible redox reaction, augments Na+ storage capability, and mitigates volume expansion during cycling. The optimal cathode manifests superior rate capability and a long life span with 107.5 mA h g–1 at 1 C and 82.5% capacity retention over 5000 cycles at 20 C. The hard carbon//NMVP@C full cell confirms practical applicability with good electrochemical performance. This work underscores the pivotal interplay among the carbon layer, Na+ mobility, and structural integrity in NASICON cathodes, offering a pathway to develop high-performance and cost-effective cathode materials for sodium-ion batteries.
✓ 已验证
产品关联
DOI
高影响因子
JOURNAL OF COLLOID AND INTERFACE SCIENCE
·
2025
·
IF 9.7
Haolong Tan,Tongwei Gao,Wensheng Yang,Yue Gao,Quan Xie,Yunjun Ruan,Qian Chen,Tinghong Gao
The rapid development of microelectronic devices has increased the demand for miniature energy storage systems that are highly safe and exhibit long cycling life and excellent energy density. However, the lack of low-cost and high-performance fabrication methods presents a significant challenge to thin-film electrode fabrication. This study reports a strategy combining controllable pre-curing treatment with rapid thermal annealing (RTA), which enables in situ fabrication of high-quality sodium vanadium phosphate [Na 3 V 2 (PO 4 ) 3 ] thin films. RTA facilitates the cleavage of weak metal–O bonds in the precursor film, whereas optimisation of the pre-curing duration (0–100 s) effectively eliminates organic residues and strengthens the carbon framework, suppressing particle agglomeration. This synergistic control substantially improves crystallization uniformity and film densification, resulting in a refined grain structure and highly oriented crystal facets. Under optimal conditions, the thin film demonstrates a high specific capacity of 85.6 mAh g −1 at a current density of 1 A g −1 , retains 72.5 mAh g −1 even at 20 A g −1 , and demonstrates 90.3 % capacity retention after 200 cycles. Moreover, the assembled full sodium-ion cell exhibits an average operating voltage of 1.3 V while maintaining 94.2 % capacity retention after 500 cycles. This study elucidates for the first time the synergistic regulation pathway of the pre-curing–RTA coupling mechanism in Na 3 V 2 (PO 4 ) 3 thin-film fabrication and proposes an advanced preparation strategy for cost-effective, highly integrated, high-power sodium-ion thin-film devices, providing critical theoretical foundations and robust technical support for next-generation all–solid state sodium microbattery design and development.
✓ 已验证
产品关联
DOI
PubMed
高影响因子
危险品化学品经营许可证（带存储）