Journal of Environmental Chemical Engineering
·
2023
·
IF 7.7
Zi-Ying Zeng,Dong-Dong Zhou,Shu-Tong Yang,Miao-Miao Su,Zhong-Hua Yang
This work synthesized a novel adsorbent by doping COF and MIL-125(Ti) in the nanoparticles Fe 3 O 4 . The obtained results showed that the doping of COF and MIL-125(Ti) had a positive effect on enhancing the specific surface area and adsorption capacity. Moreover, the adsorption process has been confirmed to follow the Langmuir model and pseudo-second-order kinetic, and the maximum adsorption capacity for tetracycline and tebuconazole was 138.1 mg/g and 87.73 mg/g, respectively. Finally, the adsorbent displayed an excellent adsorption performance in three kinds of actual environmental water samples. The mechanics of the adsorption process mainly involved π-π stacking interaction, hydrogen-bonding interaction, electrostatic interaction, and complexation interaction. In short, the synthesized magnetic adsorbent displayed a good application potential for removing tetracycline and tebuconazole from wastewater.
研究领域:
环境科学
·
材料科学
✓ 已验证
产品关联
DOI
高影响因子
Materials Research Express
·
2019
·Vol. 6
·期 10
·105316
·
IF 1.449
Ruoyu Liu,Chuanbing Huang,Lingzhong Du,Hao Lan,Shige Fang,Weigang Zhang
Aluminium/polyimide (Al/PI) powders were prepared via in situ. Al/PI composites were fabricated by hot pressing technology at 723 K for 30 min under Ar. The microstructure, thermal stability and tribological properties of Al/PI composites were investigated. SEM images showed that Al particles were wrapped in the composite with no gap. According to the TG analysis, 15Al/PI composite showed excellent thermal stability up to 773 K. Meanwhile, 15Al/PI composites exhibited excellent tribological behaviour at high temperature, especially at 773 K. The friction coefficient of 15Al/PI composite at 773 K was about 0.28 which was lower than that of pure PI (about 0.41). The wear rate of 15Al/PI composite at 773 K was about 65 × 10−5 mm3 Nm−1. The tribological properties of Al/PI composites was improved at high temperature. In the process of sliding tests, Al particles were transferred to the Ti-6Al-4V alloy's surface and PI particles were pressed on the composite's surface. The transfer of Al can protect Ti-6Al-4V alloy from wear and reduce the friction coefficient during the sliding test.
研究领域:
材料科学
·
摩擦学
✓ 已验证
DOI
高影响因子
Materials Advances
·
2023
·Vol. 4
·期 3
·940-947
·
IF 5
Xiaobing Yang,Junjie Pan,Bingcong Xing,Wenjie Lei,Yingchun Fu,Kejun Cheng
Nowadays, aflatoxin B1 (AFB1) contamination is considered as one of the most common food safety issues for humans and animals. As one of the most advanced oxidation techniques, photocatalytic degradation can break down organic contaminants into nontoxic and harmless materials efficiently. In this paper, we explored the degradation efficiency of AFB1 by ZnIn2S4. To promote the photocatalytic degradation efficiency of AFB1, ZnIn2S4 was coupled with MIL-125(Ti) and then doped with La [this hybrid is denoted as La-ZnIn2S4/MIL-125(Ti)] to effectively convert it via photocatalytic generation of superoxide radicals (˙O2− and ˙OH) and achieve much enhanced photocatalytic performance, which is demonstrated by degrading 97.6% of AFB1. According to the transient photocurrent responses, the doping of La and coupling with MIL-125(Ti) can highly improve the efficient separation of the photoinduced electron–hole pairs on ZnIn2S4, leading to the effective conversion of OH− and O2 into ˙O2− and ˙OH, respectively, during the photodegradation process. This strategy of coupling with MOFs and doping with rare earth elements provides a facile and efficient method for degrading food pollutants produced by aflatoxins.
研究领域:
食品安全
·
环境科学
·
材料科学
✓ 已验证
产品关联
DOI
高影响因子
Nanoscale
·
2024
·Vol. 16
·期 22
·10727-10736
·
IF 5.8
Peijiao Chen,Zhijun Li,Pengze Wang,Yuxin Yao,Tianwei Dou,Yang Qu,Liqiang Jing
The photocatalytic water-mediated CO2 reduction reaction, which holds great promise for the conversion of CO2 into valuable chemicals, is often hindered by inefficient separation of photogenerated charges and a lack of suitable catalytic sites. Herein, we have developed a glycerol coordination assembly approach to precisely control the distribution of atomically dispersed Cu species by occupying Ti-defects and adjusting the ratio between Cu species and Ti-defects in a hierarchical TiO2. The optimal sample demonstrates a ∼4-fold improvement in CO2-to-CO conversion compared to normal TiO2 nanoparticles. The high activity could be attributed to the Ti defects, which enhance the photogenerated charge separation and simultaneously facilitate the adsorption of water molecules, thereby promoting the water oxidation reaction. Moreover, by means of in situ EPR and FTIR spectra, we have demonstrated that Cu species can effectively capture photogenerated electrons and facilitate the adsorption of CO2, so as to catalyze the reduction of CO2. This work provides a strategy for the construction of atomic-level synergistic catalytic sites and the utilization of in situ techniques to reveal the underlying mechanism.
研究领域:
材料科学
·
环境科学
·
化学
✓ 已验证
产品关联
DOI
PubMed
高影响因子
Frontiers of Chemical Science and Engineering
·
2021
·Vol. 16
·期 3
·384-396
·
IF 4.204
Liu Xiangyu,Pan Yanling,Zhang Peng,Wang Yilin,Xu Guohao,Su Zhaojie,Zhu Xuedong,Yang Fan
Alkylation of benzene to value-added, high octane number and low toxic toluene and xylenes provides a way to lower benzene content in gasoline pool, and is hence a method to promote fuel quality. On the other hand, CO 2 accumulation in the atmosphere causes global warming and requires effective route for its valorization. Utilization of CO 2 as a carbon source for benzene alkylation could achieve both goals. Herein, alkylation of benzene with CO 2 and H 2 was realized by a series of low-cost bifunctional catalysts containing zinc/titanium oxides (Zn/Ti oxides) and HZSM-5 molecular sieves in a fixed-bed reactor. By regulating and controlling oxygen vacancies of Zn/Ti oxides and the acidities of HZSM-5, benzene conversion and CO 2 conversion reached 28.7% and 29.9% respectively, along with a total selectivity of toluene and xylene higher than 90%. In this process, more than 25% CO 2 was effectively utilized and incorporated into the target products. Moreover, the mechanism of the reaction was analyzed and the course was simultaneously traced. CO 2 was transformed into methanol firstly, and then methanol reacted with benzene generating toluene and xylene. The innovation provides a new method for upgrading of fuels and upcycling the emissions of CO 2 , which is of great environmental and economic benefits.
研究领域:
化学工程
·
环境科学
·
催化科学
✓ 已验证
DOI
高影响因子
APPLIED SURFACE SCIENCE
·
2022
·
IF 7.392
Menghan Qin,Yumiao Shi,Dingkun Lu,Jingjing Deng,Guoyue Shi,Tianshu Zhou
Due to the excessive use, cephalosporin antibiotics have been detected in various aquatic environments, which may result in environmental and health concern. In this study, bimetallic metal–organic frameworks (MOFs), Hf-UiO-66 and Ti-UiO-66, were successfully designed and obtained via post-synthetic method from UiO-66 for the adsorption of cefoperazone. A serious of adsorption experiments were investigated. The adsorption kinetics and isotherms demonstrated that the adsorption process followed pseudo-second-order kinetic model and Langmuir isotherm model. Hf/Ti-UiO-66 exhibited much better adsorption performance than the undoped UiO-66. Particularly, Hf-UiO-66 had the highest adsorption capacity (346.0 mg g −1 ). With the introduction of Hf or Ti, the chemical coordination environment changed, which resulted in defective structures of MOFs. Such defective structures increased the adsorption active sites, changed the surface charges and enlarged pores. Based on the characterization by FT-IR, XPS, and zeta potential, it was identified that the electrostatic attraction, π-π stacking, hydrogen bonding and metal complexation were the driving force for the high adsorption capacity of the bimetallic MOFs. The as-prepared MOFs displayed good stability and reusability. This work provides a great prospect for the design and application of bimetallic defective MOFs in cephalosporins removal in environmental water.
研究领域:
环境科学
·
材料科学
✓ 已验证
产品关联
DOI
高影响因子
CERAMICS INTERNATIONAL
·
2025
·
IF 5.6
Canglong Li,Xuechi Lu,Xinshuai Niu,Boyuan Zou,Yao Zhao,Xuanjie Li,Yang Lu,Yongsong Luo
The magnetic refrigeration is achieved through the magnetocaloric effect of a magnetic system, which is considered a promising technology for achieving the required low temperatures in industry, daily life, and scientific research. This work experimentally investigates the magnetic behavior and magnetocaloric performance of Ho 2 CoMn 1- x Ti x O 6 (0 ≤ x ≤ 1) double perovskites. The experimental results reveal that a paramagnetic →ferromagnetic transition characterized by a sharp increase in magnetization is suppressed due to decoupling action of Ti 4+ with 3 d 0 spin configuration. As a result, the transition temperature T C reduces monotonically from 75 K at x = 0–37 K at x = 0.6, and no obvious ferromagnetic transition is identified at x = 0.8–1 due to the lack of Co 2+ –Mn 4+ interactions at so high Ti 4+ substitution concentration. In addition, the magnetocaloric effect is investigated by measuring the isothermal initial magnetization from 4 K to a temperature far above T C . The maximum magnetic entropy ( − Δ S M max ) under Δ H = 6 T does not exhibit significant variation from x = 0 (11.1 J kg −1 K −1 ) to 0.6 (11.5 J kg −1 K −1 ), while it increases noticeably from x = 0.8 (13.9 J kg −1 K −1 ) to 1 (17.2 J kg −1 K −1 ). The present work indicates that the cryogenic magnetocaloric effect can be improved by dilution effect of nonmagnetic ions.
研究领域:
材料科学
·
凝聚态物理
·
应用物理
·
磁性材料
✓ 已验证
产品关联
DOI
高影响因子
Nanomaterials
·
2023
·Vol. 13
·期 18
·2579
·
IF 5.3
Yue Chang,Minmin Han,Yehui Ding,Huiyun Wei,Dawei Zhang,Hong Luo,Xiaogang Li,Xiongbo Yan
Effectively regulating and promoting the charge separation and transfer of photoanodes is a key and challenging aspect of photoelectrochemical (PEC) water oxidation. Herein, a Ti-doped hematite photoanode with a CoFe-LDH cocatalyst loaded on the surface was prepared through a series of processes, including hydrothermal treatment, annealing and electrodeposition. The prepared CoFe-LDH/Ti:α-Fe2O3photoanode exhibited an outstanding photocurrent density of 3.06 mA/cm2at 1.23 VRHE, which is five times higher than that of α-Fe2O3alone. CoFe-LDH modification and Ti doping on hematite can boost the surface charge transfer efficiency, which is mainly attributed to the interface interaction between CoFe-LDH and Ti:α-Fe2O3. Furthermore, we investigated the role of Ti doping in enhancing the PEC performance of CoFe-LDH/Ti:α-Fe2O3. A series of characterizations and theoretical calculations revealed that, in addition to improving the electronic conductivity of the bulk material, Ti doping also further enhances the interface coupling of CoFe-LDH/α-Fe2O3and finely regulates the interfacial electronic structure. These changes promote the rapid extraction of holes from hematite and facilitate charge separation and transfer. The informative findings presented in this work provide valuable insights for the design and construction of hematite photoanodes, offering guidance for achieving excellent performance in photoelectrochemical (PEC) water oxidation.
研究领域:
材料科学
·
能源转换
·
电化学
✓ 已验证
产品关联
DOI
PubMed
高影响因子
JOURNAL OF MATERIALS SCIENCE & TECHNOLOGY
·
2024
·
IF 11.2
Rong Liu,Yan Gao
Preparing metal-organic frameworks (MOFs) film in situ on the surface of the Ti-6Al-4V (TC4) titanium alloy is challenging owing to the dense and stable surface TiO 2 passive film. In this study, titanium-doped zirconium-based MOFs (Zr(Ti)-MOFs) film was constructed in situ on the TC4 alloy in one step at a low temperature and atmospheric pressure, with ZrCl 4 as the source of Zr metal ions. ZrCl 4 attacked and dissolved the TiO 2 film to form Zr-O-Ti bonds on the surface of TC4 to provide nucleation sites for further reactions. At the same time, Zr 4+ and dissolved Ti 4+ combined in solution to form Ti containing Zr-O cluster nodes, which aggregated and grafted to the Zr-O-Ti bonds on the substrate surface, and reacted with organic ligands (terephthalic acid) to form Zr(Ti)-MOFs film. The Ti 4+ dissolved from the TC4 participate in the Zr-MOFs formation, thereby changing the high temperature and high-pressure conditions required for the traditional preparation of Zr-MOFs (UiO-66). The in situ preparation of Zr(Ti)-MOFs on TC4 was achieved at 80°C under atmospheric pressure conditions. This study elucidated the growth mechanism of Zr(Ti)-MOFs on the TC4 surface, providing a reference for the design and in-situ preparation of multifunctional MOFs on the TC4 titanium alloy.
研究领域:
材料科学
·
表面工程
·
化学工程
✓ 已验证
产品关联
DOI
高影响因子
CATALYSIS COMMUNICATIONS
·
2023
·
IF 3.7
Shengzhe Wang,Hongxia Lv,Chengyu Jin,Yu Wang,Huangzhao Wei,Chenglin Sun,Lian Yu,Lei Ma,Xiangnan Li,Xiaowei Liu
We synthesized a series of Ru-Ti-Ni/CNT electrodes to degrade levofloxacin in wastewater. The unique structure of Ni single-atom-kernelled Ru nanoparticles regulates the reaction process, producing a notable synergistic effect. The reaction kinetics constant of Ru-Ti-Ni/CNT with a Ru: Ti ratio of 10:0 outperforms Ni/CNT by 3.7 times and CNT alone by 16.4 times. Comprehensive characterizations revealed its morphology and structure nature. Ru nanoparticles can shield Ni, while Ni single-atom facilitates electron transfer in Ru nanoparticles, generating abundant reactive oxygen radicals (ROS) that degrade pollutants.
研究领域:
环境科学
·
材料科学
·
电化学
✓ 已验证
产品关联
DOI
高影响因子
INDUSTRIAL & ENGINEERING CHEMISTRY RESEARCH
·
2023
·
IF 4.2
Hui Qi,Lida Wang,Wen Sun,Zhengqing Yang,Xu Chen,Jiao Yu,Wenzheng Wu,Guichang Liu
Chlorine evolution anodes are widely used in industrial electrolysis, whose electrocatalytic activity and stability need to be improved urgently in order to improve energy efficiency. In this study, Ti/IrRuSnSbOx electrodes were fabricated by thermal decomposition of hydrosol precursor solution. The microstructure and electrochemical behavior of the electrodes were investigated by material characterization and electrochemical tests. The results showed that the electrode with a total oxide loading of 1.1 ± 0.5 mg/cm2 had the lowest chlorine evolution potential (1.068 V vs SCE), the lowest Tafel slope (41.08 mV dec–1), and a long accelerating lifetime (405 h). The hydrosol process effectively improved the performance of the electrode by promoting the formation of oxygen vacancies and strengthening the stability of the solid solution structure. This study provided a facile method for preparing chlorine evolution electrodes with low cost, high activity, and high stability.
研究领域:
材料科学
·
电化学
✓ 已验证
产品关联
DOI
高影响因子
JOURNAL OF MATERIALS SCIENCE
·
2017
·Vol. 53
·期 7
·4927-4938
·
IF 2.599
Liu Ran,Zhang Juan,Xu Zhice,Zhao Dishun,Sun Shuang
Iron phthalocyanine (PcFe) was loaded on Ti-MCM-41 as visible light photocatalyst (R-PcFe/Ti-MCM-41). Dibenzothiophene (DBT) was photooxidized using R-PcFe/Ti-MCM-41 as a photocatalyst, air as an oxidant, and ionic liquid as the extraction agent during visible light irradiation at room temperature and ambient conditions. The results indicated that photocatalytic efficiency of the amino iron phthalocyanine (NH 2 -PcFe)/Ti-MCM-41 was superior to the other substituent groups. The DBT content in the model oil decreased from 1000 to 44 μg/mL with 95.6% removal rate under the optimal reaction conditions (model oil 10 mL, photocatalyst NH 2 -PcFe/Ti-MCM-41 0.02 g, loading amount of NH 2 -PcFe 0.3 g/g, air flow rate 100 mL/min, reaction time 2 h, room temperature). The kinetics of photocatalytic oxidation of DBT follows first-order kinetics with a rate constant of 1.319 h −1 and halftime of 0.525 h. The photocatalyst NH 2 -PcFe/Ti-MCM-41 was reused for five times, and the catalytic activity decreased slightly. The photocatalytic oxidation system demonstrated significant desulfurization effects on different sulfur compounds and real gasoline, and the sulfur content of the actual gasoline could be reduced from 1000 to 78 ppm.
研究领域:
化学工程
·
环境科学
✓ 已验证
产品关联
DOI
高影响因子
危险品化学品经营许可证（带存储）