FOOD CHEMISTRY
·
2022
·
IF 9.231
Rui-Miao Chang,Yan-Yang Zhang,Guang-Bin Zhang,Xiao-Xia Zhang,An-Jia Chen,Wen Zhang,Yong Li
The purpose of this study was to treat UiO-66 (University of Oslo 66) under suitable thermal alkaline hydrolysis condition to realize the loading of gallic acid. UiO-66-SH (UiO-66-separated-heating) was obtained by separated heating UiO-66 and 0.2 M KOH aqueous solution to 120 ℃ before mixing for 3 h. The material was in an amorphous state, maintained the octahedron structure and size of UiO-66. UiO-66-SH has better porosity and specific surface area than UiO-66, and had good thermal stability until heated to 1000 ℃. Furthermore, UiO-66-SH had very little influence of the cellular activity of human normal heptical cell line, demonstrating its good biocompatibility. The prepared UiO-66-SH could successfully adsorb gallic acid and control the release of gallic acid in simulated gastric fluid (∼58% vs. ∼ 88% of free gallic acid). This study will be conducive to preparation of appropriate carrier used to load with polyphenolic compounds such as gallic acid.
✓ 已验证
产品关联
DOI
PubMed
高影响因子
MICROPOROUS AND MESOPOROUS MATERIALS
·
2022
·
IF 5.876
Yan Gao,Miao Yan,Jianshe Zhao
A composite PW 4 @UIO-66-NH 2 /GO was designed and prepared via facile in-situ synthesis method for catalytic oxidation desulfurization of fuel. The proper sizes (window size and pore size) of UIO-66-NH 2 can effective sealing PW 4 as monomolecular active component and prevent PW 4 leaching during the reaction process. At the same time, the introduction of GO can improve the electron transfer of the catalyst. Characterization tests showed that the active component PW 4 was successfully encapsulated with a loading amount of 0.19 mmol/g. The desulfurization results indicated that the PW 4 @UIO-66-NH 2 /GO has excellent catalytic activity, which can remove 99.9% sulfides in model fuel, and the activity did not decrease obviously after repeated use for ten times. The good activity and reusability of PW 4 @UIO-66-NH 2 /GO attributes to the introduction of GO and UIO-66-NH 2 . In addition, based on GC-MS and EPR results, a possible mechanism of desulfurization reaction was proposed.
✓ 已验证
产品关联
DOI
高影响因子
Applied Materials Today
·
2021
·
IF 10.041
Kai Wang,Shuaishuai Ding,Lijuan Zeng,Jingrong Zhou,Yuhua Cao,Jiaqian Wu,Lu Lu,Xiu-wu Bian,Gan Tian
Hypoxia-acquired radioresitance is considered to be a major factor responsible for the clinical failure of radiotherapy. Carbonic anhydrase IX (CA IX), a hypoxia-induced cell-surface enzyme involved in pH regulation of hypoxic solid tumors, has been acknowledged as a desirable target for cancer therapy. Herein, we developed a dual exogenous/endogenous CA IX inhibition strategy using core/satellite-like metal-organic framework (UiO-66)/gold nanoparticles (Au NPs) nanohybrids as a therapeutic platform for hypoxia-relief enhanced RT of triple negative breast cancer. The UiO-66 matrix supported the Au NPs generation in situ and would decompose inside tumor cells by the high-concentration phosphates to release p -phthalic acid (PTA), a original building skeleton of the UiO-66 matrix, to inhibit CA IX, while the decorated Au NPs served as radiosensitizers to potentiate the sensitivity of tumor cells to X-ray and yet provided active sites for CA IX antisense oligonucleotide (ASO) loading via formation of stable Au-S bond to knockdown CA IX. The dual inhibitory manner, exogenous inhibition from PTA and endogenous inhibition from CA IX ASO, largely alleviated the hypoxia-induced resistance and synergized with Au NPs-mediated radiosensitization to afford super therapeutic outcome in vitro and in vivo , supporting the feasibility of our synergistic RT strategy in hypoxic tumor management.
✓ 已验证
产品关联
DOI
高影响因子
CHEMICAL ENGINEERING JOURNAL
·
2021
·
IF 13.273
Jian Chen,Jinbo Ouyang,Wenqian Chen,Zepeng Zheng,Zhen Yang,Zhirong Liu,Limin Zhou
Porous chitosan/Zr-MOF (UiO-66) composite foams (CSF@UiO-66) were facilely prepared by grafting UiO-66 into polymerized chitosan using epichlorohydrin as the linking agent. The flexible foams with high loadings of UiO-66 exhibited low density (15.0 ∼ 23.4 mg/cm 3 ) and superior liquid–solid separation performance. The hierarchical pores and abundant functional groups contributed to the effective removal of ketoprofen (KPF) from water by the composite foams, achieving a maximum adsorption capacity of 209.7 mg/g at pH 4, outperforming most reported adsorbents. Batch adsorption experiments demonstrated that the adsorption of KPF could be described by the Langmuir isotherm and pseudo-second-order kinetic model. Importantly, the composite foams showed excellent performance even in the presence of some ions and good reusability for engineering applications. Furthermore, density functional theory (DFT) calculations revealed that the adsorption mechanism between the composite foams and KPF could be attributed to hydrogen bonding and π-π interaction. In essence, this work provides an innovative strategy for the fabrication of a blocky composite foam with high loadings of MOF for efficient adsorptive removal of KPF in liquids, which can overcome the disadvantages of agglomeration due to small particle size and poor stability of MOFs.
✓ 已验证
产品关联
DOI
高影响因子
ANALYTICA CHIMICA ACTA
·
2021
·
IF 6.558
Yawen Wu,Xiaolong Chen,Xiaogang Luo,Mei Yang,Changjun Hou,Danqun Huo
Carcinoembryonic antigen (CEA) is a key serum tumor marker which is overexpressed in all types of adenocarcinomas. Therefore, establish the ultrasensitive, accurate and rapid method for CEA detection is essential for reducing the mortality of cancer. Here, a bimetallic organic framework Cu/UiO-66 was synthesized through the simple two-step hydrothermal method and used to construct a “fluorescence turn-on” analytical method for CEA detection. Cu/UiO-66 can adsorb CEA aptamers modified with FAM (CEA/FAM-Apt) and take place photoinduced electron transfer (PET) between Cu/UiO-66 and FAM, resulting in the fluorescence of the FAM is quenched. When CEA is present, CEA and CEA/FAM-Apt are tightly combined, making CEA/FAM-Apt far away from the Cu/UiO-66 surface. As a result, the fluorescence intensity of the system was significantly restored. Under optimal conditions, the proposed “fluorescence turn-on” method can detect CEA as low as 0.01 ng mL −1 in a range of 0.01–0.3 ng mL −1 . Besides, this analytical method owns good selectivity , reproducibility and serum applicability, which provides a new platform for the direct detection of clinical diagnosis-related markers.
✓ 已验证
产品关联
DOI
PubMed
高影响因子
MICROCHEMICAL JOURNAL
·
2021
·
IF 4.821
Mingying Ma,Tianhao Wu,Zhian Hu,Gongwei Sun,Sichun Zhang
High-throughput sample preparation is important in clinical mass spectrometry (MS) analysis. In this work, we developed a method by coupling Nano-ESI-MS with magnetic SPE using a MOF material, Fe 3 O 4 @UiO-66, as sorbent for simultaneous determination of testosterone (T) and androstenedione (4-AD) in serum samples. The proposed method presented good linearity in the range of 0.1–5 μg/L and the recoveries of serum samples were 90.7%-110.0% and 101.7%-108.7% for T and 4-AD, respectively. The results indicated that the Fe 3 O 4 @UiO-66 is an ideal sorbent for androgens extraction and the method is reliable for high-throughput quantitation of T and 4-AD in clinical applications.
✓ 已验证
DOI
高影响因子
MICROCHEMICAL JOURNAL
·
2021
·
IF 4.821
Yuanyuan Niu,Jianfeng Zhou,Haohong Lai,Qing Zhou,Shumei Wang,Haiyun Zhai
A sensitive and selective electrochemical sensor for sensing 4-nitroquinoline N-oxide (4-NQO) by differential pulse voltammetry was designed. Poly L-histidine (P-L-his) composite and metal-organic framework UiO-66 (Zr) modified electrode was used as the working electrode which had large specific surface area, mesoporous structure and excellent conductivity. Unlike most modification methods, UiO-66 was electrodeposited in this study. Compared with drop coating, electrodeposition proceeds efficiently under mild conditions and often requires shorter time. FTIR, EDX, TEM, SEM and electrochemical assay were used to characterize the prepared materials and modified electrodes. After that, some experimental conditions like electro-polymerization time, deposition time, pH and scan rate were also improved and optimized separately. At the UiO-66/P-L-his-modified glassy carbon electrode, a good linear relationship between 4-NQO concentration and its peak current was obtained under the best conditions in a wide range from 0.2 to 50.0 μM, and the limit of detection (S/N = 3) was 66.7 nM. Moreover, multiple experiments elucidated that the as-synthesized sensor could be applied to detect 4-NQO in actual samples, and the recoveries results obtained were satisfactory.
✓ 已验证
产品关联
DOI
高影响因子
CHEMICAL ENGINEERING JOURNAL
·
2021
·
IF 13.273
Mengmeng Zhang,Qian Sun,Yuejiao Wang,Weijun Shan,Zhenning Lou,Ying Xiong
Reported powdery adsorbents with poor adsorption efficiency and stability make it imperative to develop novel materials to extract gallium ions (Ga(III)) from effluents. Herein, UiO-66-NH 2 -based mixed matrix membranes (TPU/0.1THB/U6N-1.5 MMMs) via electrospinning is firstly reported for separation and recovery of Ga(III). TPU/0.1THB/U6N-1.5 MMMs efficiently overcomes multiple bottlenecks of powder UiO-66-NH 2 , including poor stability, reusability and adsorption capacity. Its maximum adsorption for Ga(III) is 96.18 mg·g −1 at pH 10.0. It has superiority in selective adsorption of Ga(III) from Al(III), Cu(II), Zn(II), Co(II) coexistence solution. Adsorption capacity of TPU/0.1THB/U6N-1.5 for Ga(III) reaches more than 80% after 9 cycles. Specially, it still retains excellent mechanical strength, flexibility and structural integrity after 12 h filtration, or after 9 adsorption-desorption cycles, even soaked in 5 mol·L -1 HCl for a week. TPU/0.1THB/U6N-1.5 MMMs also improves the problem of low water flux. TPU/0.1THB/U6N-1.5 with high MOFs loading possess high water flux of 382.2 L·m −2 ·h −1 with a permance of 382.2 L·m −2 ·h −1 ·bar −1 and rejection rates of 90% for Ga(III). The main adsorption mechanism of TPU/0.1THB/U6N-1.5 is based on the chelation between phenolic hydroxyl groups of MMMs and Ga(III) at pH 10.0. Overall, the as-prepared TPU/0.1THB/U6N-1.5 has potential for water treatment through the process of membrane adsorption.
✓ 已验证
产品关联
DOI
高影响因子
CHEMICAL ENGINEERING JOURNAL
·
2021
·
IF 13.273
Zhou Zhou,Dongyun Chen,Najun Li,Qingfeng Xu,Hua Li,Jinghui He,Jianmei Lu
In order to fix the photocatalyst and enhance the efficiency of NO degradation, a three-dimensional (3D) g-C 3 N 4 /NH 2 -UiO-66-rGO (CN/NU6-rGO) aerogel was devised and fabricated via solvothermal reaction and boiling-water bath. Herein, a type-II heterojunction was formed at CN/NU6 composite, and then, the composite was coupled with rGO. The resulting material significantly enhanced the nitric oxide (NO, 600 ppb) removal efficiency under visible-light irradiation. Optimizing the content of CN and rGO to a suitable mass ratio can increase the removal efficiency by 65.4%, which is 2.34 times that of pure NU6. This result is attributed to the construction of type-II heterojunction and the charge transport properties of rGO. The involvement of rGO not only provided extra pathways for charge transfer to prevent electron–hole pairs from recombining, but also fixed the catalyst. Moreover, the hybrid aerogel excellently reduced the harmful by-product NO 2 . Cycling experiments, along with transient photocurrent response measurements, verified that CN/NU6-rGO had excellent potential for recyclable and sustainable. This work might shed light on the construction of suitable photocatalytic systems with significant improvement of NO removal and convenient storage of catalyst.
✓ 已验证
产品关联
DOI
高影响因子
SEPARATION AND PURIFICATION TECHNOLOGY
·
2020
·
IF 5.774
Haoji Jiang,Wenxiong Shi,Qiang Liu,Heyun Wang,Jialu Li,Chunlin Wu,Yingchun Li,Zhong Wei
In order to investigate the effects of MOFs by altering ligands with various functional groups on separation selection in pervaporation dehydration, three hydrophilic UiO-66-X nanoparticles were respectively synthesized and blended into poly (vinyl alcohol) matrix to fabricate water-selective membrane for ethanol dehydration via PV technology. Both the experimental and molecular simulation results confirmed the UiO-66-X counterbalancing factors of enhanced polarity and suitable pore size gave rise to the optimal performance in ethanol dehydration. The PV performances could be tuned by the type and quantity of functional groups carried by UiO-66-X nanoparticles. As a result, the pore aperture of UiO-66-(COOH) 2 nanoparticles provided continuous channel for water diffusion, and water molecules could also be activated attributed to the strong interaction between the UiO-66-(COOH) 2 nanoparticles and water molecules which enhanced the penetration and diffusion of water molecular in hybrid membrane to increase the water flux. The optimized hybrid membranes with UiO-66-(COOH) 2 loading of 8 wt% exhibited the total flux of 979 ± 7 g/(m 2 ·h) and a separation factor of 2084 ± 21.
✓ 已验证
产品关联
DOI
高影响因子
FUEL PROCESSING TECHNOLOGY
·
2020
·
IF 4.982
Cheng Wang,Ai-Rong Li,Yu-Ling Ma
The synthesis of highly efficient and stable catalysts for oxidative desulfurization is still a challenging task. Herein, a composite material (HPMo@UiO-66) of phosphomolybdic acid (HPMo) encapsulated in the metal-organic framework UiO-66 with missing-linker defects was prepared via a one-pot hydrothermal method . A series of as-synthesized catalysts were systematically characterized by XRD , FT-IR, SEM , BET, TGA , XPS , UV–vis and PL . Through oxidative desulfurization experimental evaluations, the catalyst 0.5-HPMo@UiO-66-D with defects shows the superior catalytic oxidative desulfurization performance and high reusability . 0.5-HPMo@UiO-66-D is able to completely remove DBT in the model fuel in 60 min, and the reaction system can be recycled 10 times with a high activity. In addition, the kinetics and the activation energy of the oxidative desulfurization were studied.
✓ 已验证
产品关联
DOI
高影响因子
JOURNAL OF HAZARDOUS MATERIALS
·
2019
·
IF 7.65
Yingqing Zhan,Shuangjiang He,Jiaxin Hu,Shumei Zhao,Guangyong Zeng,Mi Zhou,Guiyuan Zhang,Arijit Sengupta
Super-wetting MOFs@graphene hybrid has shown promising application for oil/water separation, due to high porosity, low density, and controllable wettability, however, achieving excellent stability and recyclability are found to be still challenging. In this study, sandwich-like UIO-66-F 4 @rGO hybrid was synthesized by immobilization of UIO-66-F 4 nanoparticles on rGO matrix, which featured the unique micro/nano hierarchy with hydrophobic characteristics. In order to realize the oil/water separation, as-prepared sandwich-like UIO-66-F 4 @rGO hybrid was applied as a potential candidate for constructing robust super-hydrophobic/super-oleophilic interfaces by using filter paper (FP) and melamine sponge (MS) as substrates. Typically, the surface modification of substrates can be easily achieved by simple dip-coating method, and interfacial adhesion between substrates and UIO-66-F 4 @rGO was enhanced by cross-linking of hydroxyl-fluoropolysiloxane (FPSO). Consequently, the super-hydrophobic/oleophilic UIO-66-F 4 @rGO/FP exhibited high contact angle of 169.3 ± 0.6° and was capable of separating various water-in-oil emulsions effectively. The flux and separation efficiency were 990.45 ± 36.28 Lm −2 h −1 and 99.73 ± 0.19 % driven by gravity, respectively. The super-hydrophobic/super-oleophilic UIO-66-F 4 @rGO/MS possessed selective oil absorption with absorption capacity of 26∼61 g/g depending on the viscosity of oils and continuous cleaning of oil spill. Furthermore, the UIO-66-F 4 @rGO composite could tolerate high/low temperature, corrosive solutions, and physical damage, displaying robust and stable super-hydrophobic/super-oleophilic interfaces for treating oily wastewater in harsh environments.
✓ 已验证
产品关联
DOI
PubMed
高影响因子
危险品化学品经营许可证（带存储）