ANALYTICAL CHEMISTRY
·
2011
·
IF 5.874
Cheng-Xiong Yang,Xiu-Ping Yan
The diverse structures and pore topologies, accessible cages and tunnels, and high surface areas make metal–organic frameworks attractive as novel media in separation sciences. Here we report the slurry-packed MIL-101(Cr) column for high-performance liquid chromatographic separation of substituted aromatics. The MIL-101(Cr) packed column (5 cm long × 4.6 mm i.d.) offered high-resolution separation of ethylbenzene (EB) and xylene, dichlorobenzene and chlorotoluene isomers, and EB and styrene. The typical impurities of toluene and o-xylene in EB and styrene mixtures were also efficiently separated on the MIL-101(Cr) packed column. The column efficiencies for EB, m-dichlorobenzene, and m-chlorotoluene are 20000, 13000, and 10000 plates m–1, respectively. The relative standard deviation for five replicate separations of the substituted aromatics was 0.2–0.7%, 0.9–2.9%, 0.5–2.1%, and 0.6–2.7% for the retention time, peak area, peak height, and half peak width, respectively. The MIL-101(Cr) offered high affinity for the ortho-isomer, allowing fast and selective separation of the ortho-isomer from the other isomers within 3 min using dichloromethane as the mobile phase. The effects of the mobile phase composition, injected sample mass, and temperature were investigated. The separation of xylene, dichlorobenzene, and chlorotoluene on MIL-101(Cr) was controlled by entropy change, while the separation of EB and styrene on MIL-101(Cr) was governed by enthalpy change.
研究领域:
分析化学
·
材料科学
✓ 已验证
产品关联
DOI
PubMed
高影响因子
Journal of Environmental Chemical Engineering
·
2024
·
IF 7.4
Hao Wang,Renting Huang,Wei Mao,Hao Xu,Chutong Ling,Junru Zhao,Fan Yi,Yongxin Zhou,Jinghong Zhou
Iron-based metal-organic frameworks (MOFs) represent a potentially important tool for controlling organic pollutants . However, the structural stability of most iron-based MOFs in the aqueous environment is limited. Therefore, this study sought to improve the aqueous stability and photocatalytic activity of MIL-101(Fe) using an in-situ modification strategy. A novel and highly water-stable MIL-101(Fe)@IPA 4 was prepared using ligand regulation. Owing to the in-situ modification effect, MIL-101(Fe)@IPA 4 exhibited remarkable hydrophobicity with a water contact angle at 102.4° while maintaining minimal leaching of iron ions (0.46 mg/L), even after five cycles of photocatalysis . Under MIL-101(Fe)@IPA 4 /UV/H 2 O 2 conditions, the removal rates of ciprofloxacin and total organic carbon reached 100% and 49.16%, respectively, within 60 min. These researches suggest that introducing IPA improves the light absorption properties of MIL-101(Fe)@IPA 4 and facilitates electron-hole separation, thereby promoting the generation of active species. The ecotoxicity assessment of major degradation intermediates of ciprofloxacin was conducted using the ECOSAR system. Our findings provide novel insights for enhancing the water stability of iron-based MOFs through an in-situ modification strategy, which is crucial for pollution control efforts.
研究领域:
环境科学
·
材料科学
✓ 已验证
产品关联
DOI
高影响因子
NEW JOURNAL OF CHEMISTRY
·
2021
·Vol. 45
·期 6
·3120-3127
·
IF 3.591
Yixuan Huang,Liyan Xie,Kangji Zhuo,Hao Zhou,Yanhui Zhang
MIL-101(Fe)-based composite materials and their application for the generation of H2 by the catalytic reduction of nitro organics are reported in this study. NaBH4 and water contribute hydrogen for the catalytic reduction of nitro organics, but the possibility of nitro organics as a potential hydrogen source is often overlooked due to the simplicity of the reaction. However, experiments have revealed that the reaction process is accompanied by the production of H2, which is affected by the concentration of nitro organics. Moreover, the reaction is more conducive to the generation of H2 compared to NaBH4 hydrolysis under the same conditions. Unlike specially catalyzing the expensive NaBH4 hydrolysis, hydrogen is a by-product of the reduction of pollutants by inexpensive catalysts (NaBH4 acted as an electron donor for the catalyst). Accordingly, the reaction mechanism of p-nitrophenol hydride reduction was optimized. This work provides a new perspective on the application of this reaction.
研究领域:
化学工程
·
环境科学
·
材料科学
✓ 已验证
产品关联
DOI
高影响因子
RSC Advances
·
2016
·Vol. 6
·期 93
·90232-90238
·
IF 3.289
Xiao-Fang Liu,Hu Li,Heng Zhang,Hu Pan,Shan Huang,Kai-Li Yang,Song Yang
Catalytic ethanolysis of furfuryl alcohol (FA) to ethyl levulinate (EL) with MIL-101(Cr)–SO3H, prepared by simple one-pot hydrothermal treatment, is presented for the first time. The as-prepared catalyst with high surface area, hydrothermal and chemical stability, good dispersion, and feasible accessibility of –SO3H Brønsted acid sites was found to show superior performance to other sulfonic acid-functionalized solid catalysts. Besides the special textural properties, the obtained good catalytic activity of 79.2% EL yield and 100% FA conversion were also dependent on the density and strength of the Brønsted acid and the reaction parameters. A slight loss of catalytic activity after five consecutive recycles and the hot filtration experiment confirmed the good stability of MIL-101(Cr)–SO3H. Two coexisting reaction paths for the ethanolysis of FA to EL catalyzed by MIL-101(Cr)–SO3H were proposed, wherein 2-ethoxymethylfuran (2-EMF) was observed to be the dominant intermediate.
研究领域:
化学工程
·
催化科学
✓ 已验证
产品关联
DOI
高影响因子
JOURNAL OF POROUS MATERIALS
·
2019
·Vol. 26
·期 6
·1607-1618
·
IF 1.947
Hou Pengchao,Xing Guangjian,Han Dan,Zhao Yan,Zhang Gang,Wang Hao,Zhao Chang,Yu Chunna
MIL-101(Cr)/graphene aerogel (MIL-101(Cr)/GA) was synthesized using a two-step synthesis and used as a high efficient adsorbent for wastewater purification. The as-prepared MIL-101(Cr)/GA was characterized using XRD, FTIR and Raman spectroscopy, XPS and FESEM to investigate its structure, composition and morphology. MIL-101(Cr)/GA exhibited a 3D interconnected macroporous framework comprised of graphene sheets, on which MIL-101(Cr) particles were dispersed uniformly. Dyes, organic solvents and oils were used to evaluate the adsorption performance of MIL-101(Cr)/GA, which exhibited an excellent adsorption capacity for both anionic methyl orange (331.5 mg g −1 ) and cationic rhodamine B (345.7 mg g −1 ) as well as 51–101 times its own weight of various solvents/oils. In addition, the MIL-101(Cr)/GA showed superior recycling stability for dyes and a rapid adsorption rate for solvents/oils. The excellent adsorption performance was attributed to a synergistic effect between MIL-101 and the graphene aerogel. The kinetic behavior for adsorption observed for MIL-101(Cr)/GA was well-fitted by a pseudo-second-order kinetic model. It is envisaged that MIL-101(Cr)/GA will be a promising adsorbent for the removal of pollutants and wastewater purification.
研究领域:
材料科学
·
环境科学
✓ 已验证
产品关联
DOI
高影响因子
MICROPOROUS AND MESOPOROUS MATERIALS
·
2019
·
IF 4.182
Qiang Wang,Congcong Wei,Dandan Li,Wenjun Guo,Dazhong Zhong,Qiang Zhao
Metal–organic frameworks (MOFs) have been widely used in the field of electrocatalysis in recent years. In most reports, an MOF is used as a sacrificial template to prepare a highly efficient electrocatalyst by calcination . Here, a series of FeNi bimetallic MIL-101 materials has been synthesized by a solvothermal method and directly applied for the oxygen evolution reaction (OER). These MOFs contain a large number of catalytically active MO 6 octahedra and exposed hydrophilic carboxyl groups, which are believed to enhance OER activity. In addition, after the introduction of Ni, the catalytic activity is significantly improved by synergy between the metals. Among the studied compositions, Fe 2 Ni-MIL-101 showed the best OER performance, requiring a low overpotential of just 237 mV to drive a current density of 20 mA cm −2 in 1 m KOH solution, corresponding to a low Tafel slope of 44.2 mV dec −1 . Moreover, the electrochemical properties remained virtually unchanged during a 40-h long-term stability test. These findings enrich the application of MOFs materials in the field of electrocatalysis.
研究领域:
材料科学
·
电化学
✓ 已验证
产品关联
DOI
高影响因子
SENSORS AND ACTUATORS B-CHEMICAL
·
2017
·
IF 5.401
Wanqing Zhang,Zhongyin Zhang,Yuanchao Li,Jun Chen,Xiaobo Li,Yadong Zhang,Yuping Zhang
A novel MIL-101(Cr)/XC-72 modified glassy carbon electrode (GCE) sensor was fabricated to determine chloramphenicol (CAP). The electrochemical sensors were constructed by using MIL-101(Cr), XC-72, MIL-101(Cr)/XC-72, and their electrochemical performances were studied with cyclic voltammetry (CV) and differential pulse voltammetry (DPV) methods. In comparison with the GCE , MIL-101(Cr)/GCE and XC-72/GCE sensors, the MIL-101(Cr)/XC-72/GCE sensor exhibited a well-defined redox peak towards CAP in phosphate buffer solution (PBS). The effects of the ratio of MIL-101(Cr) and XC-72, accumulation time, scan rate, and pH value were carefully considered. Under the optimized conditions, the sensor exhibited excellent response for CAP. The linear concentration ranges of CAP were from 1.0 × 10 −8 to 2.0 × 10 −5 M (R 2 = 0.985), with a low detection limit of 1.5 × 10 −9 M (S/N = 3). Furthermore, the MIL-101(Cr)/XC-72/GCE sensor was successfully applied to the determination of the real samples with satisfactory recoveries.
研究领域:
分析化学
·
环境科学
·
材料科学
✓ 已验证
DOI
高影响因子
CHEMICAL ENGINEERING JOURNAL
·
2020
·
IF 10.652
Jiaxing Wang,Yaseen Muhammad,Zhu Gao,Syed Jalil Shah,Shuangxi Nie,Lihan Kuang,Zhongxing Zhao,Zhiwei Qiao,Zhenxia Zhao
Adsorption of volatile organic compounds (VOCs) under high humidity is crucial for metal–organic frameworks (MOFs) in practical applications. To enhance competitive adsorption of VOCs under humidity, polyethylene glycol (PEG) with hydrophobic short-chains was implanted as hydrophobic barrier into MIL-101(Cr). Characterization and simulation results showed that the terminal –OH groups of PEG chains were coordinated with the Cr sites in MIL-101(Cr) and formed a hydrophobic pore (11.2 Å) of “cage-in-cage” geometry. PEG chains significantly hindered the diffusion of water into the MOFs while allowed toluene molecules. The new hydrophobic pores of PEG 5 @MIL-101 enhanced adsorption capacity and diffusivity for toluene by 30.8% (4.68 mmol/g at 1 mbar) and 31.5% (1.88 × 10 −2 ), while decreased adsorption capacity and diffusivity for water by 53.7% and 26.8% compared to primary MOF. Breakthrough curve showed 3.3 times of toluene working capacity on PEG 5 @MIL-101 at 80% RH compared to pristine MIL-101(Cr).
研究领域:
材料科学
·
环境科学
✓ 已验证
产品关联
DOI
高影响因子
Journal of Physical Chemistry C
·
2021
·
IF 4.126
Qinchao Shao,De Zhang,Cai-e Wang,Zhexiang Tang,Mingqiang Zou,Xiaobing Yang,Huaping Gong,Zhi Yu,Shangzhong Jin,Pei Liang
Surface-enhanced Raman scattering (SERS), owing to its high sensitivity and rapid response, has been widely used in various fields. However, it is still a challenge to prepare SERS substrates with high stability and reproducibility. Metal–organic frameworks (MOFs), with excellent enrichment capacity and stability, provide a new material for high-performance SERS substrates. In this paper, we prepare a MIL-101(Cr) film via a secondary growth method, and Ag+ is reduced to Ag NPs by UV irradiation and attach to the film to synthesize the Ag@MIL-101(Cr) film SERS substrate. Then, we change the time of UV light illumination and the amount of silver nitrate in order to obtain the optimal substrate. The detection capability of this sample can be up to 10–11 M for 4-ATP, and the relative standard deviation (RSD) is only about 5%, which demonstrates that the substrate has excellent SERS effect and reproducibility. Finally, the prepared substrate has been applied for the determination of nitrofurantoin, with its detection capability up to 10–7 M. This work proposes a simple method to synthesize MOF-based film substrate with high SERS performance and uniformity and provides potential for the sensitive detection of chemical or antibiotic residue.
研究领域:
材料科学
·
分析化学
✓ 已验证
产品关联
DOI
高影响因子
APPLIED CATALYSIS A-GENERAL
·
2023
·
IF 5.5
Huifang Feng,Yitong Sun,Qiaozhen Xu,Hong Liu
Developing efficient photocatalyst to promote the conversion of CO 2 into value-added chemicals remains challenging. Here, novel NH 2 -MIL-101(Fe)@Bi 2 MoO 6 S-scheme heterojunctions were fabricated via a solvothermal method, in which Bi 2 MoO 6 (BMO) nanoparticles uniformly growing on the NH 2 -MIL-101(Fe) (NM101) octahedrons with intimate contact interface. The resultant heterojunctions revealed significantly enhanced activity for CO 2 photoreduction. The optimal performance was achieved when the content of BMO was 10 wt%, and the formation rate of CO reached 67.0 μmol·g −1 ·h −1 under visible light illumination (with apparent quantum efficiency of 0.09 % at 450 nm), which was 3.2-fold of individual NM101. The boosting activity benefited from the formation of S-scheme heterojunction at the NM101 @BMO interfaces, which facilitated the separation of photoinduced electron-hole pairs with strong redox ability at the interface. This S-scheme charge transfer mechanism was further validated by the in-situ XPS and fluorescence probe molecular experiment. Besides, the intermediates and preliminary mechanism of photoreaction were unraveled based on in-situ DRIFTS analysis. This work provides some novel insights for designing efficient S-scheme photocatalysts for CO 2 photoreduction.
研究领域:
材料科学
·
环境科学
·
化学
✓ 已验证
产品关联
DOI
高影响因子
Inorganics
·
2022
·Vol. 10
·期 3
·33
·
IF 3.149
Tian Zhao,Hexin Zhu,Ming Dong,Minmin Zou,Songfan Tang,Mingliang Luo,Xianggang Li
The chromium-benzenedicarboxylate metal–organic framework (MOF), MIL-101(Cr), is one of the most well-investigated and widely used prototypical MOFs. Regarding its synthesis, the use of a toxic modulator (usually HF) and high reaction temperature (220 °C) are the main factors hindering its further expansion of production and utilization. In fact, high quality MIL-101(Cr) crystals can be prepared at a much lower temperature (160 °C) with spherical morphology via an additive-free approach. Compared to traditional octahedral MIL-101(Cr), the spherical MIL-101(Cr) possesses higher adsorption performance toward dye molecules, including methyl orange (MO) and rhodamine B (RB). The results suggest that toxic additives and high reaction temperatures are not essential in the synthesis of MIL-101(Cr), and the fabrication of spherical MIL-101(Cr) may offer a facile and effective pathway for the large-scale industrial application of MIL-101(Cr).
研究领域:
材料科学
·
环境科学
✓ 已验证
DOI
高影响因子
Catalysts
·
2018
·Vol. 8
·期 9
·394
·
IF 3.465
Tian Zhao,Ming Dong,Ling Yang,Yuejun Liu
Nowadays, the controllable synthesis of stable hierarchical metal–organic frameworks (MOFs) is very important for practical applications, especially in catalysis. Herein, a well-known chromium–benzenedicarboxylate metal–organic framework, MIL-101(Cr), with a stable hierarchical structure, was produced by using phenylphosphonic acid (PPOA) as a modulator via the hydrothermal method. The presence of phenylphosphonic acid could create structural defects and generate larger mesopores. The synthesized hierarchical MIL-101(Cr) possesses relatively good porosity, and the larger mesopores had widths of 4–10 nm. The hierarchical MIL-101(Cr) showed significant improvement for catalytic activity in the oxidation of indene. Further, the presence of a hierarchical structure could largely enhance large dye molecule uptake properties by impregnating.Keywords:MIL-101(Cr);phenylphosphonic acid;hierarchical;enhanced catalytic activity;large molecule uptake
研究领域:
材料科学
·
催化化学
✓ 已验证
产品关联
DOI
高影响因子
危险品化学品经营许可证（带存储）