COMPOSITES PART B-ENGINEERING
·
2019
·
IF 6.864
Yanfei Li,Yuanyuan Fu,Shouhui Chen,Zhenzhong Huang,Li Wang,Yonghai Song
A rapid and simple way to prepare porous Fe 2 O 3 /Fe 3 O 4 @carbon octahedron arrayed on three-dimensional graphene foam (Fe 2 O 3 /Fe 3 O 4 @C/G) nanocomposites was developed. Firstly, Fe-metal organic frameworks (MOFs)/graphene oxide (GO) precursor was fabricated by growing octahedral Fe-MOFs on the surface of GO and then the as-prepared Fe-MOFs/GO was rapidly transformed into porous Fe 2 O 3 /Fe 3 O 4 @C/G by combusting the mixture of precursors and triethylamine (TEA) in air. In the combustion process, GO was reduced and connected each other into N-doped G foam, and Fe-MOFs were transformed into porous Fe 2 O 3 /Fe 3 O 4 @C octahedron and arrayed on G foam. The porous structure, porous carbon and G foam relieved the volume expansion of Fe 2 O 3 /Fe 3 O 4 nanoparticles , and enhanced electrical conductivity of nanocomposites. The as-prepared Fe 2 O 3 /Fe 3 O 4 @C/G showed a high discharge capacity (1210 mAh g −1 , 200 cycles) and long cycle life (5 A g −1 , 400 cycles) when was applied to lithium-ion batteries. This work to prepare Fe 2 O 3 /Fe 3 O 4 @C/G nanocomposites through the combustion of TEA and Fe-MOFs/GO could save energy, achieve rapid preparation and shorten the reaction time. It might provide an original way for fabrication of transition metal oxides@C derived from MOFs and a constructive view into the preparation of composite materials.
✓ 已验证
DOI
高影响因子
Desalination and Water Treatment
·
2024
·
IF 1
Hui Huang,Bin Huang,Yichun Huang,Jinbei Yang,Yinnv Ye,Yucheng Chen
Attractive environmentally friendly magnetic metal-organic framework (MOF) nanocomposite GO@Fe 3 O 4 -COOH@NH 2 -MIL-101(Fe) was synthesized by a solvothermal method and characterized by X-ray diffraction, Fourier transform infrared, scanning electron microscopy, Brunauer– Emmett–Teller, and vibrating sample magnetometer, and used as an effective adsorbent for the removal of orange G from aqueous solution. The various operating parameters that effect the adsorption process, such as adsorbent dosage (0.01–0.2 g), pH (1.0–10.0), initial concentration (50–400 mg L –1 ), and temperature (298.15–318.15 K) were studied. The percent removal of orange G increases with the increment of the adsorbent dosage and decrease of the initial concentration, and the optimum pH is 6.0. The Redlich–Peterson model can be favorably applied to describe the adsorption equilibrium data, indicating that the surfaces of GO@Fe 3 O 4 -COOH@NH 2 -MIL-101(Fe) nanocomposite for the orange G adsorption are made up of homogeneous adsorption patches. The adsorption kinetics indicate that the adsorption process of GO@Fe 3 O 4 -COOH@NH 2 -MIL-101(Fe) toward orange G obeys the pseudo-second-order model and the activation energy is 16.5 kJ mol –1 . Thermodynamic parameters, ΔH = 39.81 kJ mol –1 , ΔS = –46.80 J mol –1 K –1 , and ΔG < 0, exhibit that the adsorption is exothermic and spontaneous. The maximum adsorption capacity of orange G onto GO@Fe 3 O 4 -COOH@NH 2 -MIL-101(Fe) nanocomposite is 128.8 mg g –1 . Therefore, magnetic GO@ Fe 3 O 4 -COOH@NH 2 -MIL-101(Fe) nanocomposite can be employed as an environmentally friendly and efficient adsorbent for the orange G removal from wastewater.
✓ 已验证
DOI
高影响因子
JOURNAL OF ENVIRONMENTAL ENGINEERING
·
2020
·Vol. 146
·期 7
·04020056
·
IF 1.264
Hao Cai,Tianci Zhao,Zichuan Ma,Jingze Liu
Fe3O4-coated pretreated biochars (Fe3O4@PBC) were prepared for the first time by a Fe(III)-ethanol solution impregnation-calcination method. When photo-Fenton catalysts were used, their effectiveness in removing metronidazole (MNZ) from aqueous media was evaluated. Fe3O4@PBC samples were characterized by X-ray diffraction, scanning electron microscope, vibrating sample magnetometer, X-ray photoelectron spectroscopy, and Brunauer–Emmett–Teller methods. The results showed that Fe3O4 coating was successfully formed on the surface of HNO3- pretreated biochar, and Fe3O4@PBC can be separated by applying an external magnetic field. The coating of Fe3O4 did not change the pore structure and maintained a high surface area of the biochar. Fe loading significantly affected the photo-Fenton degradation and adsorption ability of MNZ. The highest MNZ removal rate and the greatest catalytic ability were found in the PBC-6.6Fe sample containing 6.6% Fe by mass. Various operating parameters, such as solution pH, H2O2 concentration, and MNZ concentration, were tested during MNZ’s photo-Fenton catalytic degradation. The results indicate that the highest MNZ degradation efficiency can be derived from a moderate acidic solution, and the optimal pH is 3. Using PBC-6.6Fe, the increase of H2O2 concentration from 30 to 60 mmol·L−1 promotes the degradation of photo-Fenton, and both an excessive H2O2 and an increase in MNZ concentration suppressed the process. Under the conditions of 0.4 g·L−1 PBC-6.6Fe, 300 mg·L−1 MNZ, 60 mmol·L−1 H2O2, and initial pH of 3, 95.1% of MNZ was degraded. The PBC-6.6Fe had good stability, and its removal efficiency was still over 92% after five repeated uses. This study confirmed that •OH played a dominant role, while O2•− and h+ played a weaker role in the photo-Fenton system. The results indicated that Fe3O4@PBC served as a prospective visible-light-driven catalyst similar to Fenton for the treatment of wastewater containing MNZ.
✓ 已验证
DOI
高影响因子
TALANTA
·
2020
·
IF 5.339
Ting Zhang,Lingli Lei,Meiling Tian,Junjie Ren,Zhisong Lu,Yang Liu,Yingshuai Liu
An ultrasensitive lateral flow immunoassay (LFIA) strip has been developed based on a multifunctional photothermal contrast Fe 3 O 4 @Au supraparticle (Fe 3 O 4 @Au SP) for quantitative Ochratoxin A (OTA) detection. The Fe 3 O 4 @Au SP composite not only shows a better photothermal effect over Fe 3 O 4 and gold nanoparticles , but possesses magnetic property and excellent ability to directly adsorb protein (antibody). Under 808 nm irradiation, photothermal images of the test strips are recorded by a portable Infrared thermal camera. A quantitative analysis is easily achieved based on the thermal changes, which are proportional to the concentrations of analytes. Under an optimal condition, a wide linear detection range from 1 pg mL⁻ 1 to 1μgmL⁻ 1 and a limit of detection (LOD) at 0.12 pg mL⁻ 1 have been achieved with OTA as a model analytes. The practical application potential has also been validated by detection of OTA in spiked corn , peanut, and soybean extractives with overall recoveries ranging from 98.6% to 115% and coefficient of variations (CVs) between 6.06% and 12.73%. The photothermal LFIA renders a rapid, sensitive, and quantitative bio-/chemo-sensing platform with only a portable laser source and a thermal camera.
✓ 已验证
DOI
高影响因子
Polymer Chemistry
·
2014
·Vol. 5
·期 14
·4332-4338
·
IF 5.368
Feng Wang,Liyan Huang,Jun Li,Lina Lin,Zhengping Liu,Zhaoxia Dong
Well-defined superparamagnetic and conductive Fe3O4/polyaniline (PANI) hollow spheres were fabricated using positively charged polystyrene (PS) spheres as templates. The negatively charged Fe3O4 particles, which were decorated by citric acid, can be attached onto the surface of the PS spheres via electrostatic interaction. Subsequently, the PANI layer was coated onto the PS/Fe3O4 templates by in situ chemical oxidative polymerization. Finally, removal of the PS core by dissolving with tetrahydrofuran provided the electromagnetic hollow spheres. Morphologies and compositions of Fe3O4/PANI hollow spheres were investigated by using SEM, TEM, FTIR and XRD. Magnetic analysis demonstrates that the synthesized composite spheres possess the characteristic of superparamagnetism and the saturation magnetization value is 26.2 emu g−1. Batch adsorption shows that the Fe3O4/PANI hollow spheres exhibit high uptake property of Pb2+ in aqueous solution. The adsorption kinetics follows the mechanism of pseudo-second-order kinetics and the sorption agrees well with the Langmuir isotherm.
✓ 已验证
DOI
高影响因子
CERAMICS INTERNATIONAL
·
2020
·
IF 3.83
Zhen Wang,Zhi Cheng,Li Xie,Xianliang Hou,Changqing Fang
Ti 3 C 2 T x MXene has been explored as an efficient electromagnetic interference (EMI) shielding material because of its high electrical conductivity , large specific surface area, rich surface defects , and abundant functional groups. Herein, core-shell Fe 3 O 4 @PANI composites were prepared, followed by the preparation of a flexible and lightweight Ti 3 C 2 T x /Fe 3 O 4 @PANI composite film with sandwich intercalation structure by vacuum-assisted filtration, using Ti 3 C 2 T x MXene as a matrix material. The ultrathin composite film with a Ti 3 C 2 T x nanosheets to Fe 3 O 4 @PANI weight ratio of 12:5 reached a maximum EMI shielding effectiveness (SE) value of 58.8 dB at a thickness of only 12.1 μm. This is much higher than the SE of pure conductive Ti 3 C 2 T x films of the same thickness. After adjusting the film thickness by increasing the concentration of Ti 3 C 2 T x , an SE of 62 dB was achieved at a thickness of 16.7 μm. The ultrathin Ti 3 C 2 T x /Fe 3 O 4 @PANI films exhibit potential for application in packaging, wearable electronic equipment, and military fields. Moreover, they provide insight into the preparation of lightweight and progressive electromagnetic shielding materials.
✓ 已验证
DOI
高影响因子
JOURNAL OF PHYSICS D-APPLIED PHYSICS
·
2020
·Vol. 53
·期 24
·245401
·
IF 3.169
Jingyi Xue,Xiaolei Li,Qianli Li,Jiahong Lyu,Wei Wang,Lin Zhuang,Yue Xu
A novel magnetic drug-loaded osteoinductive Fe3O4/CaCO3 hybrid microspheres system (MDHMs) with excellent drug delivery property has been fabricated by a modified coprecipitation method. The MDHMs are uniform vaterite microspheres with well-defined mesoporous nanostructures. The formation of vaterite is based on the templating effect of casein micelles, which is promising in bone tissue engineering. Cyclodextrins (CDs) increase the porosity of the microspheres with a pore size of about 7.3 nm and a surface area of about 50.73 m2 g−1. The mesoporous structure gives the MDHMs great drug loading efficiency of about 80.75–88.74% and the minocycline-loaded MDHMs display a sustained drug release property (about 95% in 5 d). Moreover, the MDHMs also possess stable magnetic property with a saturation magnetization of about 4.41 emu g−1 and a remarkable magnetism-responsive behavior. These results demonstrate that with superior drug delivery property, osteoinductive potential and magnetic property, the MDHMs have a great potential in the treatment of peri-implantitis.
✓ 已验证
DOI
高影响因子
NEW JOURNAL OF CHEMISTRY
·
2018
·Vol. 42
·期 11
·8914-8923
·
IF 3.201
Baihong An,Yanan Liu,Chengcheng Xu,Han Wang,Jun Wan
Visible light responsive Fe3O4–WSe2/NG (nitrogen doped graphene oxide) heterojunction nanocomposites were synthesized by a hydrothermal synthesis route, in which Fe3O4 and WSe2 particles were coated on the surface of NG. The samples were characterized by XRD, SEM, TEM, XPS, VSM, UV-vis DRS, TOC, and GC-MS techniques. The results showed that the photocatalytic activity of Fe3O4–WSe2/NG photocatalysts under visible-light illumination was higher than that of WSe2/NG owing to the narrow band gap energy and delayed electron–hole recombination, and Fe3O4 can be used in advanced oxidation processes (AOPs) to degrade organic pollutants at pH 3 and 3.0 mM H2O2. Moreover, the mass fraction of Fe3O4 had a great effect on the photocatalytic activity of Fe3O4–WSe2/NG. Among the hybrid photocatalysts, 30 wt%Fe3O4–WSe2/NG (30 wt% of Fe3O4) exhibited the highest photocatalytic activity with a rate constant of 0.05589 min−1 for the degradation of MB in aqueous solution under visible light irradiation, and the removal efficiency reached 98.8% which was 1.6 times higher than that of WSe2/NG. More importantly, the magnetic properties of 30 wt%Fe3O4–WSe2/NG were analyzed and its reusability was also investigated after four successive runs by applying an external magnetic field.
✓ 已验证
DOI
高影响因子
LANGMUIR
·
2021
·
IF 3.882
Yang Wang,Yingying Wei,Qianrui Xu,Shimin Shao,Hong Man,Yingrui Nie,Zhifei Wang,Yong Jiang
Magnetic materials perform well in the purification of histidine-rich proteins (His-proteins). In this work, a facile fabrication of yolk–shell magnetic Fe3O4@NiSiO3/Ni microspheres for the efficient purification of His-proteins has been reported. Yolk–shell Fe3O4@NiSiO3 microspheres were prepared via hydrothermal reaction. Then Ni nanoparticles (NPs) were loaded on Fe3O4@NiSiO3 microspheres after the adsorption and in situ reduction of nickel acetylacetonate. The yolk–shell Fe3O4@NiSiO3/Ni microspheres had a hierarchical flower-like structure and large cavities. The size of the cavity depended on the reaction time. This indicated that the microspheres had a large specific surface area for loading of more Ni NPs, which was crucial to the high His-protein adsorption capacity of Fe3O4@NiSiO3/Ni microspheres. Fe3O4@NiSiO3/Ni microspheres had a high adsorption capacity for bovine hemoglobin (BHb, 2822 mg/g), which was better than the values of other His-protein adsorbents. Fe3O4@NiSiO3/Ni microspheres still had a high BHb separation efficiency after seven separation cycles, indicating its good reusability and stability. Therefore, the as-prepared bifunctional yolk–shell Fe3O4@NiSiO3/Ni microspheres exhibited great practical application value for His-protein purification.
✓ 已验证
DOI
高影响因子
ENVIRONMENTAL SCIENCE AND POLLUTION RESEARCH
·
2022
·Vol. 29
·期 23
·35204-35216
·
IF 5.19
Song Xu,Mo Jingqian,Fang Yuting,Luo Shumin,Xu Jingjing,Wang Xu
We prepared a double-layer magnetic nanocomposite Fe 3 O 4 @ZIF-8@ZIF-67 by layer-by-layer self-assembly. Fe 3 O 4 @ZIF-8@ZIF-67 was used to remove tetracycline from an aqueous solution via a combination of adsorption and Fenton-like oxidation. Depending on the outstanding porous structure of the Fe 3 O 4 @ZIF-8@ZIF-67, a high adsorption capacity for tetracycline was 356.25 mg g −1 , with > 95.47% removal efficiency within 100 min based on Fenton-like oxidation. To better understand the mechanisms involved in integrated adsorption and Fenton-like oxidation, various advanced characterization techniques were used to monitor the changes in morphology and composition of Fe 3 O 4 @ZIF-8@ZIF-67 before and after removal of tetracycline. Scanning electron microscopy/energy-dispersive X-ray spectroscopy (SEM/EDS), Fourier transform infrared spectroscopy (FTIR), and X-ray diffraction (XRD) all supported adsorption and Fenton oxidation of tetracycline. This study extends the application of Fe 3 O 4 @ZIF-8@ZIF-67 for environmental remediation. Graphical abstract
✓ 已验证
DOI
高影响因子
NANOTECHNOLOGY
·
2023
·Vol. 34
·期 40
·405602
·
IF 3.5
Tiantian Si,Shuai Xie,Zhijiang Ji,Zihao Wu,Chao Ma,Junyu Wu,Jing Wang
The development of practical and efficient electromagnetic wave (EMW) absorbing materials is a challenging research problem. A mussel-inspired molecular structure regulation strategy using polydopamine to increase the roughness and functional groups of basalt fiber (BF) surface, which can improve the fiber interfacial adhesion. Herein, a novel BF-Fe3O4/CNTs heterostructure is synthesized through a dip-coating adsorption process. The three-dimensional network structure of Fe3O4/CNTs hybrid in situ anchored on the surface of BF, which endows the composite to have good intrinsic magnetic and dielectric properties. Modulation of EMW absorption performance by controlling the addition of CNTs, the minimum RL of BF-Fe3O4/7C reaches to −40.57 dB at a thickness of 1.5 mm with CNTs addition of 7%. The enhanced EMW absorption performance of BF-Fe3O4/7C heterostructure may be attributed to the synergistic effects of interfacial polarization between the hollow magnetic Fe3O4 spheres and CNTs, conduction loss, magnetic resonance loss and multiple reflection/scattering inside the BF. This work provides a simple pathway to design EMW absorbing materials with good environmental stability.
✓ 已验证
DOI
高影响因子
Frontiers in Chemistry
·
2022
·
IF 5.545
Wang Yangyang,Xu Jianfeng,Wang Xiaoshu,Li Tongtong,Zhang Gen,Yan Zheng,Liu Jiancong,Wang Lei
The background value of iron in red soil is superior, primarily absorbed and homogeneously encapsulated in harvested biomass. However, this property on the high-value utilization of bionic iron-encapsulated biomass remains unknown. In this study, special biochar (Fe@BC) was obtained from this kind of biomass by one-step pyrolysis method, which was further used to activate peroxydisulfate (PDS) and degrade 2,4-dichlorophenol (2,4-DCP). The results showed that Fe3O4 was formed and homogeneously embedded in biochar at 500oC. Comparing to catalysts prepared by impregnation pyrolysis (Fe/BC), Fe@BC exhibited excellent degradation performance (90.9%, k = 0.0037 min−1) for 2,4-DCP. According to the free radicals quenching studies, hydroxyl radicals (·OH) and superoxide radicals (·O2−) were the dominant reactive oxygen species (ROS) in Fe@BC/PDS system. Importantly, a PDS adsorption model was established, and the electron transport and PDS activation in the core-shell structure were demonstrated by DFT calculations. Therefore, this study could supply a high-performance catalyst and significant implications for high-value biomass utilization in red soil.
✓ 已验证
DOI
高影响因子
危险品化学品经营许可证（带存储）