CHEMICAL ENGINEERING JOURNAL
·
2026
·
IF 12.5
Liuqing Chen,Xiuhong Meng,Huibo Qin,Xiao Ling,Zebing Bao,Zhiqiang Xie,Xinping Ouyang,Linhai Duan
The coupling of liquefied natural gas and adsorbed natural gas charging (LNG-ANG) can effectively recover boil-off gas, with the key challenge being the development of efficient and stable adsorbents under cryogenic conditions (∼159 K). HKUST-1 is regarded as a promising methane adsorbent due to its abundant microporous structure and high specific surface area. However, its practical application is largely limited by water instability. After exposure to humid air for 10 days, the pristine HKUST-1 lost 68.17% of its specific surface area and 30.77% of its methane uptake capacity. Herein, we successfully prepared a water-stability-enhanced HKUST-1-PVP composite by grafting polyvinylpyrrolidone (PVP) onto the coordinatively unsaturated metal sites of HKUST-1. Among the samples, HKUST-1-P2 maintained a high specific surface area of 1242 m 2 g −1 (a loss of only 3.27%) and essentially unchanged methane uptake capacity even after exposure to humid air for at least 70 days. Furthermore, under LNG-ANG adsorption conditions (159 K, 6 bar), the methane uptake capacity of HKUST-1-P2 reached 234 cm 3 (STP) cm −3 , which is 2.6 times that of HKUST-1. These results indicate that the PVP modification strategy significantly enhances the structural stability of HKUST-1 and further stabilizes its methane adsorption performance. Computational simulations revealed that PVP grafting onto unsaturated Cu sites creates a barrier that blocks water access, thereby effectively enhancing the material's water stability. This work not only provides a simple and effective strategy for constructing water-stable MOF adsorbents but also advances the practical application of HKUST-1 materials in LNG-ANG technology.
✓ 已验证
产品关联
DOI
高影响因子
Journal of Environmental Chemical Engineering
·
2026
·Vol. 14
·期 3
·122285
·
IF 7.5
Faruk Omar,Dian Ding,Zhuo Chen,Zhihua Zhao
Selective room-temperature detection of 1-octen-3-ol, a representative fungal volatile organic compound (VOC) associated with food spoilage, remains challenging due to limited adsorption–activation efficiency in conventional sensing materials. Herein, pristine Zeolitic imidazolate framework (ZIF-67) and Rhodium (Rh)-decorated ZIF-67 (Rh@ZIF-67) were developed as chemiresistive sensing materials via a mild solution-based strategy, achieving controlled Rh loadings (0.4–0.6%) while preserving the polyhedral ZIF-67 framework. The crystal structure, surface chemical states, porosity, and morphology were systematically characterized by X-ray diffraction (XRD), X-ray photoelectron spectroscopy (XPS), Brunauer–Emmett–Teller (BET) surface area analysis, scanning electron microscopy (SEM), and transmission electron microscopy coupled with energy-dispersive X-ray spectroscopy (TEM/EDS), confirming that the ZIF-67 framework was preserved and Rh species were successfully anchored on the porous host. At room temperature (25°C), the optimized 0.5%Rh@ZIF-67 sensor exhibits a stable concentration-dependent response over 5–50 ppm, delivering a response of 2.41 at 50 ppm—approximately 15.1 times higher than pristine ZIF-67 (0.16) with response and recovery times of 90 s and 119 s, respectively. The sensor further demonstrates good selectivity, repeatability, and long-term stability over 25 days. Humidity evaluation (30–90%) Relative Humidity (RH) indicates moderate response attenuation attributed to competitive adsorption of water molecules. The enhanced sensing performance is attributed to synergistic adsorption enrichment from porous ZIF-67 combined with Rh-induced catalytic and electronic sensitization, enabling efficient resistance modulation under ambient conditions. This work provides a promising strategy for low-power, selective monitoring of spoilage-related VOC biomarkers in practical storage environments.
✓ 已验证
产品关联
DOI
高影响因子
CHEMICAL PAPERS
·
2026
·
IF 2.7
Li Huaitao,Feng Yuexia,Wu Jun,Lu Jian,Hua Xueting,Li Feng
Biodegradable plastics, widely recognized as promising substitutes for conventional plastics, still face the challenge of microplastic contamination to require in-depth assessments of combined pollution scenarios. This study explored the adsorption of 1-chloronaphthalene (PCN-1) by biodegradable plastics including poly(butylene adipate-co-terephthalate) (PBAT) and polylactic acid (PLA) with polyethylene (PE) as a conventional plastic control in seawater. The maximum adsorption capacity of PCN-1 on PLA/PBAT/PE in seawater reached 131.22/323.59/301.80 μg g −1 . The desorption efficiency of PCN-1 from PLA and PBAT was substantially lower than that from PE, suggesting that biodegradable plastics might pose reduced environmental risks due to low pollutant release. Interaction between PCN-1 and biodegradable plastics could be regulated by pH, which was attributed to the modulation of π-π stacking interactions. Salinity exerted a positive effect on the adsorption capacity of PCN-1 by PLA, PBAT, and PE; the maximum capacities (131.22/323.59/301.80 μg g −1 , respectively) were achieved at a salinity of 30‰. Pseudo-second-order model obtained good fitting on adsorption kinetics of PCN-1 on PLA while PBAT and PE exhibited higher consistency with the pseudo-first-order model. Thermodynamic analysis based on enthalpy (ΔH) and Gibbs free energy (ΔG) changes revealed that PCN-1 adsorption on PLA was an endothermic process, while the adsorption on PBAT and PE was exothermic. Collectively, the capture of PCN-1 by biodegradable plastics is predominantly governed by three key factors: crystallinity of the plastic matrix, π-π interaction between the plastic and PCN-1, and hydrophobic interaction.
✓ 已验证
产品关联
DOI
高影响因子
Frontiers in Nutrition
·
2025
·
IF 5.1
Jia Li,Lijia Li,Tahui Lin,Houtan Huang,Jie Ren,Jengyuan Yao
Background: Food-derived flavonoids are emerging as nutraceutical agents for glycemic control. Dihydromyricetin (DMY), the signature flavanonol of vine tea (Ampelopsis grossedentata), has long been consumed in South China, yet its antidiabetic potential remains underexplored.Methods: We administered DMY (50 and 100 mg/kg/day, 12 days) to streptozotocin-induced type 1 diabetic mice. Fasting glycemia, lipid panels, and HOMA-β were evaluated 4 weeks after DMY administration. Untargeted UPLC-QTOF metabolomics combined with network pharmacology pinpointed pathway hubs, while experiments in INS-1 β-cells using the PI3K inhibitor LY294002 verified the pathway’s involvement.Results: DMY reduced hyperglycemia, corrected dyslipidemia, and preserved islet architecture. Metabolomics indicated a shift toward a normal plasma profile, with the arachidonic acid, linoleic acid, and steroid hormone pathways being the most responsive. Six hub targets (PTGS2, IL6, AKT1, IL1B, BCL2, CASP3) mapped to eicosanoid signaling, apoptosis, and PI3K/AKT axis. Docking and cell assays confirmed direct binding and PI3K/AKT-dependent cytoprotection, evidenced by restored p-AKT, lowered ROS, and reduced caspase-3 cleavage.Conclusion: DMY, a readily accessible food-derived bioactive compound, reprograms lipid-inflammatory metabolism and activates PI3K/AKT to safeguard β-cell viability, highlighting its nutraceutical promise for dietary management of autoimmune diabetes.
✓ 已验证
产品关联
DOI
PubMed
高影响因子
CATALYSIS COMMUNICATIONS
·
2013
·
IF 2.915
Bin Zeng,Xiaohua Chen,Xutao Ning,Chuansheng Chen,Aiping Hu,Weina Deng
Carbon nanotubes and reduced graphene oxides (CNTs/rGO) sphere decorated with Cu 2 O, CuO nanoparticles (Cu x O–CNTs/rGO) was successfully synthesized by spray drying and post-calcinating method for the first time. Scanning electron microscopy and transmission electron microscopy observations confirmed that CNTs/rGO formed a spherical micrometer structure and Cu x O nanoparticles were decorated on their surface. The experimental results indicated that this novel architecture enhanced photocatalytic performance with 97.5% decomposition of methyl orange (MO) after 20 min in the presence of H 2 O 2 under visible light irradiation, which was much higher than that of pure Cu x O powders (31.2%).
研究领域:
材料科学
·
纳米科技
·
光催化
·
环境功能材料
·
复合材料
✓ 已验证
DOI
高影响因子
CANCER BIOLOGY & THERAPY
·
2023
·
IF 3.6
Xiaojing Xing,Xuguang Wang,Meichen Liu,Qianxue Guo,Hongyue Wang
A GTPase binding protein, Ras interacting protein 1 (RASIP1), has been reported with a tumor-promoting role in lung cancer cells, and its role in lymphoma remains unknown. The analysis of medical databank shows that RASIP1 is upregulated in diffuse large B-cell lymphoma (DLBCL) specimens. In this article, we demonstrated that RASIP1 is highly expressed in DLBCL cell lines, compared with primary B cells. The gain- and loss-of-function experiments were performed to investigate the effects of RASIP1 on DLBCL cells. CCK-8, flow cytometry, western blot, and transwell assays demonstrated that silence of RASIP1 inhibited proliferation, cell cycle transition, and invasion and induced significant apoptosis in DLBCL cells, and ectopic expression of RASIP1 played opposite roles. Xenograft results revealed that RASIP1 facilitated the growth of DLBCL cells in vivo. These findings suggest that RASIP1 may be required for malignancy of DLBCL cells. In addition, we also found that the expression of RASIP1 was negatively regulated by forkhead box O3 (FOXO3), which has been reported to suppress the proliferation of DLBCL cells. Our results indicate that FOXO3 is bound to the promoter sequence of RASIP1 and inhibits its transcription. The suppressive effects of FOXO3 on proliferation and invasion of DLBCL cells were neutralized by RASIP1. In conclusion, we demonstrate that FOXO3 negatively regulated RASIP1 facilitates growth and invasion of DLBCL cells, provides novel diagnostic markers and therapeutic targets for DLBCL in clinic.
✓ 已验证
产品关联
DOI
PubMed
高影响因子
POLYMER
·
2023
·
IF 4.6
Yuhui Xie,Xue Lv,Xinyi Sui,Song Tian,Li'an Jiang,Shulin Sun
In this paper, the physicochemical double cross-linking nanocomposite hydrogels were prepared. Due to the addition of ionic liquid (1-butyl-3-methylimidazolium chloride salt), Laponite cannot spontaneously form a high thixotropic gel in water. The homogeneously dispersed Laponite nanosheets act as dynamic physical crosslinking sites, which cooperate with the chemical crosslinking center of MBA in the polymer chain segments and build a super-strong and super-tough hydrogel network structure. The PAM/Laponite/IL nanocomposite hydrogel achieves excellent tensile strength up to 1191 Kpa, a high tensile strain of 6842%, and a very high toughness of 26.62 MJ/m 3 . In this paper, an effective mechanism to enhance the mechanical properties of the hydrogel is proposed based on the structural evolution of Laponite. This highly flexible nanocomposite hydrogel shows excellent potential as a load-bearing material.
✓ 已验证
产品关联
DOI
高影响因子
Food Science and Human Wellness
·
2023
·
IF 7
Linglin Fu,Rongrong Wang,Jinru Zhou,Chong Wang,Yanbo Wang
N -glycans in many proteins are of great concern because of their strong association with food allergies. Triticum aestivum (bread wheat), a major food crop, is known as one of the “Big Eight” allergenic groups. However, little research has been done about N -glycans in wheat glycoproteins. In this study, a soluble wheat glycoprotein was purified from wheat and further identified as globulin-1 S allele (GSA). The wheat GSA displayed significant IgE-binding activity. Moreover, one N -glycosylation site and 6 kinds of N -glycans were identified by mass spectrometry, including 3 high mannose types and 3 complex types. Furthermore, the IgE-binding activity of wheat GSA is proved to be reduced by the removal of N -glycan, thermal treatment (temperatures > 80 °C), and strong acidic treatment (pH 3.0). These findings would provide a better understanding of the effects of N -glycosylation, thermal treatment, and acidic treatment on the molecular characteristics of GSA, and further provide new insights into the development of hypoallergenic wheat products.
✓ 已验证
DOI
高影响因子
JOURNAL OF ALLOYS AND COMPOUNDS
·
2023
·
IF 6.2
Siying Du,Liuyun Chen,Chengzheng Men,Hongbing Ji,Tongming Su,Zuzeng Qin
Photocatalytic H 2 production using solar energy has received great attention, but suffers from low photocatalytic efficiency. Herein, Zn (1−x) Cd x S solid solution with different Zn/Cd molar ratio was synthesized by a solvothermal method, and tested for photocatalytic H 2 production from water. The bandgap, charge carrier separation efficiency and surface defect states of the Zn (1−x) Cd x S can be adjusted by altering the Zn/Cd molar ratio. The separation efficiency of photogenerated electrons and holes was greatly enhanced with the Zn/Cd molar ratio of 0.8:0.2. Moreover, the Zn 0.8 Cd 0.2 S exposed most surface defect states compared to those of other Zn (1−x) Cd x S, which can be act as electron pools and active sites for improving photocatalytic H 2 production. Therefore, when the molar ratio of Zn/Cd is 0.8:0.2, the Zn 0.8 Cd 0.2 S exhibited the best performance for photocatalytic H 2 production with the H 2 production rate of 7.71 mmol·g -1 ·h -1 , which is much higher than that of ZnS (17 μmol·g -1 ·h -1 ) and CdS (5.37 μmol·g -1 ·h -1 ). This work provides an in-depth understanding of the surface defect states for enhancing the photocatalytic H 2 production.
✓ 已验证
产品关联
DOI
高影响因子
MATERIALS RESEARCH BULLETIN
·
2023
·
IF 5.4
Jinbiao Jia,Beibei Shi,Jia Dong,Xu Feng,Yangqing Wu,Bingqiang Cao
Although perovskite solar cells have made remarkable progress, the record device efficiency still lags far behind the theoretical limit efficiency. In this work, the ionic liquid, 1-ethyl-3-methylimidazolium chloride, is introduced into the triple-cation perovskite light absorption layer. The perovskite film with optimal amount of 1-ethyl-3-methylimidazolium chloride increases crystallinity, decreases pinholes and reduces defects density. As a result, the nonradiative recombination loss is efficiently restrained, accelerating the carrier extraction. The device modified with 1-ethyl-3-methylimidazolium chloride acquires a power conversion efficiency of 21.54%, which is considerably higher than that of the control device (18.12%). This work demonstrates that 1-ethyl-3-methylimidazolium chloride is a promising ionic liquid additive for high-performance perovskite solar cells.
✓ 已验证
产品关联
DOI
高影响因子
SEPARATION AND PURIFICATION TECHNOLOGY
·
2023
·
IF 8.6
Huahao Wang,Yaping Ding,Mengjia Ning,Miao Yu,Wenji Zheng,Xuehua Ruan,Yuan Xi,Yan Dai,Hongjing Liu,Gaohong He
Metal organic frameworks (MOFs) with appropriate pore size and sufficient CO 2 -philic groups are required to improve the mixed matrix membranes (MMMs)-based CO 2 capture. Herein, NH 2 -CPL-1 is designed for capture by utilizing amino pyrazine instead of pyrazine in CPL-1. The introduced CO 2 -philic amino groups together with rich hydroxyl and carboxyl groups in CPL-1 could improve the selective adsorption of CO 2 , enhancing the solubility selectivity. At the meantime, after the introduction of amino-functional, the pore size of NH 2 -CPL-1 is decreased from 0.93 nm of CPL-1 to 0.85 nm, which is beneficial for the screening of CO 2 over N 2 . As a result, the CO 2 separation performances of MMMs could be promoted greatly under the action of NH 2 -CPL-1. MMM with NH 2 -CPL-1 of 10 wt.% exhibited the best CO 2 separation performance, with CO 2 /N 2 selectivity of 85 and CO 2 permeability of 104 Barrer at 25 °C and 0.4 MPa. Compared with the CPL-1/Pebax-10 wt.% MMM, it was increased by 9.5 % and 13.3 %, respectively. This satisfactory CO 2 separation performance surpasses those of most reported other MOFs based MMMs, which is attributed to the facilitated CO 2 transport and pore size screening from the introduced amino groups. This is also confirmed by the improvement of diffusion selectivity and solution selectivity. The proposed NH 2 -CPL-1 shows great prospect as filler for enhanced MMMs-based CO 2 capture.
✓ 已验证
产品关联
DOI
高影响因子
APPLIED MICROBIOLOGY AND BIOTECHNOLOGY
·
2023
·Vol. 107
·期 5
·1725-1736
·
IF 5
Li Jing,Li Ziyi,Gong Hui,Ma Mengyi,Li Shuolei,Yang Huilin,Zhang Hailin,Liu Jianguo
Abstract In this study, a novel high-activity amylosucrase from Salinispirillum sp. LH10-3-1 (SaAS) was identified and characterized. The recombinant enzyme was determined as a monomer with a molecular mass of 75 kDa. SaAS protein exhibited the maximum total and polymerization activities at pH 9.0 and maximum hydrolysis activity at pH 8.0. The optimum temperature for total, polymerization, and hydrolysis activities were 40, 40, and 45 °C, respectively. Under the optimal pH and temperature, SaAS had a specific activity of 108.2 U/mg. SaAS also showed excellent salt tolerance and could retain 77.4% of its original total activity at 4.0 M NaCl. The addition of Mg 2+ , Ba 2+ , and Ca 2+ enhanced the total activity of SaAS. When the conversion of 0.1 M and 1.0 M sucrose was catalyzed at pH 9.0 and 40 °C for 24 h, the ratios of hydrolysis, polymerization, and isomerization reactions were 11.9:77.4:10.7 and 15.3:53.5:31.2, respectively. The α-arbutin yield of 60.3% was achieved from 20 mM sucrose and 5 mM hydroquinone catalyzed by SaAS. Key points
• A novel amylosucrase from Salinispirillum sp. LH10-3-1 (SaAS) was characterized.
• SaAS has the highest specific enzyme activity among all known amylosucrase.
• SaAS has hydrolysis, polymerization, isomerization, and glucosyltransferase activities.
Graphical Abstract
✓ 已验证
产品关联
DOI
PubMed
高影响因子
危险品化学品经营许可证（带存储）