Nanoscale Research Letters
·
2016
·Vol. 11
·期 1
·1-8
·
IF 2.584
Zheng Dan,Guo Peng,Xiong Juan,Wang Shengfu
A ZnO-based film bulk acoustic resonator has been fabricated using a magnetron sputtering technology, which was employed as a biosensor for detection of mucin 1. The resonant frequency of the thin-film bulk acoustic resonator was located near at 1503.3 MHz. The average electromechanical coupling factor \( {K}_{\mathrm{eff}}^2 \) and quality factor Q were 2.39 % and 224, respectively. Using the specific binding system of avidin-biotin, the streptavidin was self-assembled on the top gold electrode as the sensitive layer to indirectly test the MUC1 molecules. The resonant frequency of the biosensor decreases in response to the mass loading in range of 20–500 nM. The sensor modified with the streptavidin exhibits a high sensitivity of 4642.6 Hz/nM and a good selectivity.
✓ 已验证
产品关联
DOI
PubMed
高影响因子
ChemSusChem
·
2017
·Vol. 10
·期 13
·2796-2804
·
IF 7.226
Dong-Dong Qin,Cai-Hua He,Yang Li,Antonio C. Trammel,Jing Gu,Jing Chen,Yong Yan,Duo-Liang Shan,Qiu-Hong Wang,Jing-Jing Quan,Chun-Lan Tao,Xiao-Quan Lu
Graphical A passive catalyst? A Fe 2 O 3 shell was grown onto a ZnO core to protect the surface from corrosion and increase the charge-separation efficiency. PH 3 treatment onto the core–shell nanowire creates a Fe 2 PO 5 with dual functionality: a catalyst and passivating overlayer. Zinc oxide is regarded as a promising candidate for application in photoelectrochemical water oxidation due to its higher electron mobility. However, its instability under alkaline conditions limits its application in a practical setting. Herein, we demonstrate an easily achieved wet-chemical route to chemically stabilize ZnO nanowires (NWs) by protecting them with a thin layer Fe 2 O 3 shell. This shell, in which the thickness can be tuned by varying reaction times, forms an intact interface with ZnO NWs, thus protecting ZnO from corrosion in a basic solution. The reverse energetic heterojunction nanowires are subsequently activated by introducing an amorphous iron phosphate, which substantially suppressed surface recombination as a passivation layer and improved photoelectrochemical performance as a potential catalyst. Compared with pure ZnO NWs (0.4 mA cm −2 ), a maximal photocurrent of 1.0 mA cm −2 is achieved with ZnO/Fe 2 O 3 core–shell NWs and 2.3 mA cm −2 was achieved for the PH 3 -treated NWs at 1.23 V versus RHE. The PH 3 low-temperature treatment creates a dual function, passivation and catalyst layer (Fe 2 PO 5 ), examined by X-ray photoelectron spectroscopy, TEM, photoelectrochemical characterization, and impedance measurements. Such a nano-composition design offers great promise to improve the overall performance of the photoanode material.
✓ 已验证
产品关联
DOI
PubMed
高影响因子
JOURNAL OF MATERIALS SCIENCE
·
2017
·Vol. 52
·期 14
·8472-8484
·
IF 2.599
Xu Mengya,Wang He,Wang Gang,Zhang Lin,Liu Gang,Zeng Zhixiang,Ren Tianhui,Zhao Wenjie,Wu Xuedong,Xue Qunji
Semiconductor photocatalysts play a major role in photocatalytic process. Zinc oxide (ZnO) is supposed to be a preferred photocatalyst due to its high photosensitivity, mechanical–thermal stability, tunable morphology and non-toxicity. To enhance the photocatalytic activity of ZnO, cellulose/ZnO composite films (CZ films) with snowflake-like ZnO micro/nanoparticles immobilized in cellulose matrix were prepared by a simple dissolution and regeneration of cellulose and subsequently one-step hydrothermal synthesis of ZnO. The immobilization of ZnO was conducive to overcoming the shortcomings of aggregation easily and reclamation difficulty of scattered nanopowders. The obtained CZ films exhibited excellent photocatalytic efficiency (85.3%) to degrade methylene blue with minor amount of ZnO photocatalyst (<6 mg). The experimental results show that a photocatalytic process involving absorption–degradation–desorption was proposed. Notably, the synergistic effects between cellulose film and the supported ZnO via absorption and desorption processes were important to enhance the photocatalytic efficiency. This work provided an effective method to support ZnO photocatalyst and improve the photocatalytic efficiency via a functional substrate.
✓ 已验证
产品关联
DOI
高影响因子
JOURNAL OF THE AMERICAN CERAMIC SOCIETY
·
2017
·Vol. 100
·期 12
·5723-5730
·
IF 2.841
Zhiwei Zhou,Junyou Yang,Qinghui Jiang,Dan Zhang,Jiwu Xin,Xin Li,Yangyang Ren,Xu He
In this work, the thermoelectric properties of SnTe have been regulated synergistically by introduction of n -type ZnO nanoinclusions. On one hand, the excessive holes in SnTe matrix were compensated properly by n -type ZnO, and the Seebeck coefficient has been improved greatly due to the carrier energy filtering effect by a large quantity of ZnO-SnTe hetero-junction interface barriers; On the other hand, the thermal conductivity gets reduced by the enhanced phonon scattering from multiscale hierarchical architectures. Consequently, a maximum ZT of ~0.9 at 873K has been obtained in the 0.8 wt% sample, which enhances by 112% in comparison with the nanoinclusion-free sample.
✓ 已验证
产品关联
DOI
高影响因子
APPLIED CATALYSIS B-ENVIRONMENTAL
·
2016
·
IF 8.328
Lun Pan,Tahir Muhammad,Lu Ma,Zhen-Feng Huang,Songbo Wang,Li Wang,Ji-Jun Zou,Xiangwen Zhang
ZnO is an important semiconductor that has been widely applied in solar cell, photocatalysis, environmental remediation. Doping and morphology control are important approaches to improve its photocatalytic performance. Herein, a facile two-step calcination method was developed to fabricate carbon(C)-doped cubic ZnO with porous structure from zeolite imidazolate frameworks (ZIF-8). Compared with one-step pyrolysis, the approach of two-step calcination not only retains the cubic morphology with inter-connected ZnO nanoparticles and porous structure but also introduces C doping in ZnO lattice effectively. This morphology has advantage in charge transfer, optical absorption and mass transfer during the photoreaction, and C doping results in high charge-separation efficiency. The sample C350-400 (C-doped ZnO, firstly calcined at 350 °C for 2 h from ZIF-8, then 400 °C for 1 h) shows the maximum photoactivity, which is ca . 3-fold and 4-fold higher than ZnO (C450) in photodegradation and PEC water splitting (under UV–vis irradiation), respectively. It is expected that the preparation of metal oxide from MOF is a very promising way to fabricate highly efficient photocatalyst.
✓ 已验证
产品关联
DOI
高影响因子
POLYMERS FOR ADVANCED TECHNOLOGIES
·
2015
·Vol. 27
·期 7
·882-888
·
IF 1.757
Mehdi Derradji,Noureddine Ramdani,Lin-dan Gong,Jun Wang,Xiao-dong Xu,Zai-wen Lin,Abdelkhalek Henniche,Wen-bin Liu
In the present work, zinc oxide nanoparticles were treated with aminopropyl trimethoxy silane-coupling agent and used as a new kind of reinforcement for a typical high performance bisphenol-A-based phthalonitrile resin. The resulted nanocomposites were characterized for their mechanical, thermal, and optical properties. Results from the tensile test indicated that the tensile strength and modulus as well as the toughness state of the matrix were all enhanced with the increasing of the nanoparticles amount. Thermogravimetric analysis showed that the starting decomposition temperatures and the residual weight at 800°C were highly improved upon adding the nanofillers. At 6 wt% nanoloading, the glass transition temperature and the storage modulus were considerably enhanced reaching about 359°C and 3.7 GPa, respectively. The optical tests revealed that the neat resin possesses excellent UV-shielding properties, which were further enhanced by adding the nanofillers. Furthermore, the fractured surfaces of the nanocomposites analyzed by scanning electron microscope exhibited homogeneous and rougher surfaces compared with that of the pristine resin. Finally, the good dispersion of the reinforcing phase into the matrix was confirmed by a high resolution transmission electron microscope. Copyright © 2015 John Wiley & Sons, Ltd.
✓ 已验证
产品关联
DOI
高影响因子
APPLIED SURFACE SCIENCE
·
2016
·
IF 3.15
Chunlei Wang,Xing Tan,Juntao Yan,Bo Chai,Jianfen Li,Shizhong Chen
Magnetic ZnFe 2 O 4 /ZnO (ZFO/ZnO) multi-porous nanotubes have been first fabricated via a facile electrospinning and subsequent calcination process. A series of ZFO/ZnO photocatalysts with different ZFO molar content and morphologies are also obtained by varying the molar ratio of Zn/Fe metal salt and its dosage. The morphology, composition, crystal structure and specific surface area of achieved photocatalysts are systematically examined. TEM images demonstrate ZFO/ZnO-3 multi-porous nanotubes possess perfect 1D nanotube profile with hierarchical pores. HRTEM images confirm the formation of ZFO/ZnO heterojunctions. DRS spectra show that ZFO/ZnO-3 multi-porous nanotubes exhibit an enhanced absorption both in UV and visible-light region. PL spectra and photocurrent responses of ZFO/ZnO-3 multi-porous nanotube demonstrated that the photogenerated electrons and holes are effectively separated. Above all, ZFO/ZnO-3 multi-porous nanotubes photocatalysts with a larger specific surface area of 57.79 m 2 g −1 exhibit the best photocatalytic efficiency of 99% after 150 min under the solar irradiation for the decolorization of RhB. Moreover, ZFO/ZnO photocatalysts not only possess magnetic separation property, but also keep a relatively high photocatalytic efficiency even after four cycles, which is beneficial for practical application. In addition, both the formation and potential photocatalytic mechanisms of ZFO/ZnO-3 multi-porous nanotubes are proposed in detail.
✓ 已验证
产品关联
DOI
高影响因子
ACS Applied Materials & Interfaces
·
2017
·
IF 7.504
Yunxiang Chen,Xianzhe Zeng,Jingting Zhu,Rong Li,Heliang Yao,Xun Cao,Shidong Ji,Ping Jin
For VO2-based thermochromic smart windows, high luminous transmittance (Tlum) and solar regulation efficiency (ΔTsol) are usually pursued as the most critical issues, which have been discussed in numerous researches. However, environmental durability, which has rarely been considered, is also so vital for practical application because it determines lifetime and cycle times of smart windows. In this paper, we report novel VO2@ZnO core–shell nanoparticles with ultrahigh durability as well as improved thermochromic performance. The VO2@ZnO nanoparticles-based thermochromic film exhibits a robust durability that the ΔTsol keeps 77% (from 19.1% to 14.7%) after 103 hours in a hyperthermal and humid environment, while a relevant property of uncoated VO2 nanoparticles-based film badly deteriorates after 30 h. Meanwhile, compared with the uncoated VO2-based film, the VO2@ZnO-based film demonstrates an 11.0% increase (from 17.2% to 19.1%) in ΔTsol and a 31.1% increase (from 38.9% to 51.0%) in Tlum. Such integrated thermochromic performance expresses good potential for practical application of VO2-based smart windows.
✓ 已验证
产品关联
DOI
PubMed
高影响因子
RSC Advances
·
2017
·Vol. 7
·期 12
·7140-7149
·
IF 3.108
Yuchao Xu,Zongzhang Liu,Zheng Han,Minhua Zhang
ZnO promoted ZrO2–SiO2 catalysts synthesized by a sol–gel method were investigated in the two-step ethanol transforming to 1,3-butadiene process. The influence of promoters and the preparation method of the catalysts on the catalytic performance were studied in detail and the reaction conditions were optimized. The as-prepared catalysts were characterized by BET, X-ray diffraction (XRD), Scanning Electron Microscopy (SEM), Transmission Electron Microscopy (TEM), Fourier Transform Infrared Resonance (FT-IR), X-ray photoelectron spectroscopy (XPS), FT-IR spectroscopy of adsorbed pyridine (Py-IR) and temperature-programmed desorption of NH3 (NH3-TPD). ZnO added ZrO2–SiO2 catalysts show the best catalytic activity and the catalysts prepared by the hybrid sol–gel method were superior to those prepared by the sol–gel coupled with impregnation method. The addition of promoters in the ZrO2–SiO2 system decreased the total acidity and lowered the selectivity to dehydration products. The best performance with ethanol/acetaldehyde conversion of 40.7% and 1,3-butadiene selectivity of 83.3% was reached at 310 °C, ethanol/acetaldehyde mole ratio of 3.5 and WHSV of 1.4 h−1 using a 0.5 wt% ZnO doped ZrO2–SiO2 catalyst.
✓ 已验证
产品关联
DOI
高影响因子
JOURNAL OF THE SCIENCE OF FOOD AND AGRICULTURE
·
2016
·Vol. 97
·期 7
·2023-2029
·
IF 2.076
Biao Suo,Huarong Li,Yuexia Wang,Zhen Li,Zhili Pan,Zhilu Ai
BACKGROUND There has been limited research on the use of ZnO nanoparticle-coated film for the quality preservation of pork meat under low temperature. In the present study, ZnO nanoparticles were mixed with sodium carboxymethyl cellulose (CMC-Na) to form a nanocomposite film, to investigate the effect of ZnO nanoparticle-coated film on pork meat quality and the growth of bacteria during storage under low temperature. RESULTS When ZnO nanoparticle-coated film was used as the packaging material for pork meat for 14 days of cold storage at 4 °C, the results demonstrated a significant effect on restricting the increases in total volatile basic nitrogen and pH levels, limiting the decreases of lightness (increased L * value) and redness (increased a * value), and maintaining the water-holding capacity compared to the control pork samples ( P < 0.05). The present study also discovered that the ZnO nanoparticle-coated film restrained the increase in total plate count (TPC). When Staphylococcus aureus was used as the representative strain, scanning electron microscopy revealed that ZnO nanoparticles increased the occurrence of cell membrane rupture under cold conditions. CONCLUSION ZnO nanoparticle-coated film helps retain the quality of pork meat during cold storage by increasing the occurrence of microorganism injury. © 2016 Society of Chemical Industry
✓ 已验证
产品关联
DOI
PubMed
高影响因子
SENSORS
·
2017
·Vol. 17
·期 10
·2214
·
IF 2.677
Fan Zhou,Weixuan Jing,Pengcheng Liu,Dejun Han,Zhuangde Jiang,Zhengying Wei
In this paper, the performance of a zinc oxide (ZnO) nanorod-based enzymatic glucose sensor was enhanced with silver (Ag)-doped ZnO (ZnO-Ag) nanorods. The effect of the doped Ag on the surface morphologies, wettability, and electron transfer capability of the ZnO-Ag nanorods, as well as the catalytic character of glucose oxidase (GOx) and the performance of the glucose sensor was investigated. The results indicate that the doped Ag slightly weakens the surface roughness and hydrophilicity of the ZnO-Ag nanorods, but remarkably increases their electron transfer ability and enhances the catalytic character of GOx. Consequently, the combined effects of the above influencing factors lead to a notable improvement of the performance of the glucose sensor, that is, the sensitivity increases and the detection limit decreases. The optimal amount of the doped Ag is determined to be 2 mM, and the corresponding glucose sensor exhibits a sensitivity of 3.85 μA/(mM·cm2), detection limit of 1.5 μM, linear range of 1.5 × 10−3–6.5 mM, and Michaelis-Menten constant of 3.87 mM. Moreover, the glucose sensor shows excellent selectivity to urea, ascorbic acid, and uric acid, in addition to displaying good storage stability. These results demonstrate that ZnO-Ag nanorods are promising matrix materials for the construction of other enzymatic biosensors.Keywords:ZnO nanorod;doping;surface morphology;wettability;glucose sensor
✓ 已验证
产品关联
DOI
PubMed
高影响因子
BIOSENSORS & BIOELECTRONICS
·
2012
·
IF 5.602
Minggang Zhao,Jingyun Huang,Yu Zhou,Qi Chen,Xinhua Pan,Haiping He,Zhizhen Ye
A novel method of fabricating a free probe type nanoscale biosensor is first demonstrated. A free probe type biosensor based on a single one-dimensional (1D) mesoporous ZnO/Chitosan inorganic–organic hybrid nanostructure is constructed. The as-prepared biosensor exhibited excellent biosensing performance and was stable in solution due to its inorganic–organic hybrid structure. The special mesoporous nanostructure with protuberances favors enzymes loading and enhances electrical communication efficiency. The feasibility of employing a single 1D nanostructure as a separate free nanoprobe for biosensing is demonstrated. This kind of free probe type biosensor will not only provides a new tool for micro-targets detection in microcell and enzymatic studies, but also has the potential to be inserted into single cell or other microorganism for biological studies.
✓ 已验证
产品关联
DOI
PubMed
高影响因子
危险品化学品经营许可证（带存储）