MATERIALS SCIENCE IN SEMICONDUCTOR PROCESSING
·
2025
·
IF 4.6
Jibao Dong,Jing Jin,Weiguang Yang
Si-based anodes are limited in their widespread application mainly because of their significant volume expansion during cycling. In this study, the hollow Si thin film anode (H-Si-0.1) was prepared using ZIF-8 as a sacrificial template, followed by etching with 0.1 M hydrochloric acid (HCl). The hollow Si was coated with dual Al layers on its inner and outer surfaces, forming the Al/H-Si-0.1/Al composite thin film anode. The hollow structure provides buffering space to accommodate volume change and facilitates the formation of a gyrification-like structure on the film anode during cycling, significantly enhancing cycling stability. Moreover, the hollow structure creates efficient diffusion pathways for lithium ions, improving ion transport. The dual Al layers provide mechanical support for the structural stability of the anode and suppress side reactions. The Al/H-Si-0.1/Al thin film anode provides a high reversible capacity of 2098 mA h g −1 at 0.5 A g −1 . It exhibits a specific capacity of 1512 mA h g −1 at 5 A g −1 after 300 cycles, achieving a capacity retention of 94.56 %.
✓ 已验证
产品关联
DOI
高影响因子
Silicon
·
2025
·
IF 3.3
Yang Yonghui,Fan Chao,Yang Pengchen,Liu Zhanwei,Yan Hengwei
This study investigated the effect of aluminum oxide (Al 2 O 3 ) additives on the properties of NaF-AlF 3 -SiO 2 melts. The liquid-phase line temperature was determined through thermal analysis, while the solubility and volatilization loss of silicon dioxide (SiO 2 ) were evaluated using the rotating quartz disk method and volatilization experiments. The dissolution mechanism of Al 2 O 3 in the melt was explored through thermodynamic analysis and experimental validation. The results indicated that Al 2 O 3 addition significantly decreased liquid-phase line temperature, enhanced SiO 2 solubility, and reduced volatilization losses. These findings provide a theoretical basis for optimizing the electrolysis process of Al–Si alloys, which contribute to improved melt performance, enhanced energy efficiency, and reduced volatilization losses, thereby promoting increased efficiency in industrial applications.
✓ 已验证
产品关联
DOI
高影响因子
INDUSTRIAL & ENGINEERING CHEMISTRY RESEARCH
·
2018
·
IF 3.141
Da Wang,Zhong Wang,Guangci Li,Xuebing Li,Bo Hou
SiO2-modified high thermal conductivity Al2O3@Al composites were synthesized and supported cobalt for Fischer–Tropsch synthesis to improve the catalytic performance and intensify the heat transfer within a fixed-bed reactor. FTS results showed that the CO conversion and C5+ selectivity increased whereas CH4 selectivity decreased, which could be attributed to the reduced metal–support interaction via modification of SiO2 on the surface of Al2O3@Al. The heat transfer coefficients of the Co/SAl2O3@Al–x were more than 30 times those of conventional Co/Al2O3 according to the laser flash measurement. The thermal conductive study showed that a homogeneous radial temperature gradient was maintained within the catalyst bed for Co/SAl2O3@Al-x even without using a heat diluter, indicating good thermal conductivity within the reactor. In addition, the temperature of the catalyst bed for Co/SAl2O3@Al-x was easier to reach a “steady state” compared to the reactor packed with traditional low thermal conductive Co/Al2O3, which could improve the operating flexibility of FTS.
✓ 已验证
DOI
高影响因子
CERAMICS INTERNATIONAL
·
2021
·
IF 4.527
Shunhang Wei,Jian Gao,Pingru Wu,Bo Yao,Haitao Xu,Yongsheng Tan,Shiyan Liu,Rong Wu,Yawei Wang,Lei Wang,Zebo Fang,Qifeng Liang
Although TiO 2 is a wide band gap semiconductor , it demonstrates photodegradation activity under visible light irradiation after dye sensitization. Compared with esterification between the surface hydroxyl group of TiO 2 and the carboxylic group of dyes, electrostatic interaction between TiO 2 and dye shows better photosensitized performance. In this work, Bi/Al co-doping anatase titania (Ti 1-x Bi 2x/3 Al 2x/3 O 2 (0 ≤ x ≤ 0.3)) is designed to enhance the electrostatic interaction. The effect of Al ions is to enhance the solubility of Bi 3+ into titania nanocrystals . A new band gap is generated after high concentration of Bi element doping , which not only promotes the absorption of visible light, but also improves the utilization of photogenerated carriers. Based on the results of transmission electron microscopy , light absorption, photodegradation activity and density functional theory calculations, it is found that bismuth dopant is the electron capture site. It first accumulates electrons through photocatalytic degradation reaction to enhance electrostatic adsorption between the catalyst and the positively charged dye molecules, and finally realizes high-efficiency photosensitization degradation of Rhodamine B. In addition, the sensitized titania has excellent photodegradation recyclability.
✓ 已验证
DOI
高影响因子
JOURNAL OF THE AMERICAN CERAMIC SOCIETY
·
2020
·Vol. 103
·期 10
·5664-5677
·
IF 3.502
Yao Ji,Yongbao Xiao,Shujing Huang,Weichao Wang
Fluoro-sulfo-phosphate (FPS) glass is of current interest as potential material for laser application due to its good glass-forming ability, thermal, and chemical stability as well as the complicated local environment for incorporated species. Herein, the physical and luminescent properties of Er 3+ and Yb 3+ /Er 3+ -doped FPS glasses vs S/F ratio are investigated comprehensively. The low melting temperature (750°C) leads to fewer ingredients evaporation and easier operation. The sulfate addition depolymerizes the structure of FPS glasses, leading to either monotonic or nonmonotonic variations of physical properties, while no deterioration in thermal and limited one in chemical stability is caused. The addition of sulfate also modifies the local structure around optical active species and thus, leading to higher emission cross section (1.52 × 10 −20 cm 2 ), effective linewidth (68.4 nm), figure of merit (5.61 × 10 −23 s cm 2 ), gain bandwidth (102.44 × 10 −27 cm 3 ), and energy-transfer microparameters (51.87 × 10 −39 cm 6 /s), implying high possibility to serve as 1.5 μm laser application.
✓ 已验证
DOI
高影响因子
Journal of Materiomics
·
2024
·
IF 8.4
Weibin Chen,Yuzhen Wang,Gaochao Liu,Yongsheng Sun,Zhiguo Xia
Laser phosphor display technology plays an important role in advanced display projection; however, it is a challenge in maintaining excellent color accuracy under high brightness due to the lack of red spectrum. Here, red-emitting Mg 2 Al 4 Si 5 O 18 :Eu 2+ ceramics as the phosphor wheel have been optimized in chemical compositions and texture orientation. The textured Mg 2 Al 4 Si 5 O 18 :Eu 2+ ceramics have high transparency and spot limiting ability, accordingly, the ceramic wheel outputs 1184 l m of ultra-bright red light under 50W·mm −2 laser power density. Moreover, the red spectral utilization (＞600 nm) of textured Mg 2 Al 4 Si 5 O 18 :Eu 2+ ceramics is 2.17 times that of traditional Y 3 Al 5 O 12 :Ce 3+ phosphor wheel. The red-emitting textured Mg 2 Al 4 Si 5 O 18 :Eu 2+ cordierite ceramic herein enables an improved light-color saturation experience, and it is potential in the next-generation laser phosphor display applications.
✓ 已验证
DOI
高影响因子
INTERNATIONAL JOURNAL OF HYDROGEN ENERGY
·
2021
·
IF 5.816
Xiaomin Kang,Guodong Fu,Fengzhan Si,Xiaohui Deng,Lei Wang,Xian-Zhu Fu,Jing-Li Luo
Porous boron-bearing Fe-nitrogen doped carbon electrocatalysts (Fe-BNC) are prepared by pyrolysis treatment of Fe/B co-doped zeolitic imidazolate frameworks (ZIFs). The as-obtained Fe-BNC catalysts with a high surface area (1300 m 2 g −1 ) favor a 4-electron reduction pathway for efficient oxygen reduction reaction (ORR). The Fe-BNC catalysts demonstrate a half-wave potential of ∼0.85 V vs RHE comparable to that of Pt/C catalyst and high stability in 0.1 M KOH. The dopant of little boron and iron into nitrogen-doped carbon results in the high surface area, enhanced surface polarities, electronic properties and exposing more active sites to introduce a synergistic effect for enhanced ORR performance. Moreover, Fe-BNC electrocatalysts used as air cathode for Al-air batteries exhibit a high peak power density of 195.2 mw cm −2 and excellent stability even after discharging for 24 h at room temperature , revealing an excellent performance in application of metal-air batteries and other energy converting devices.
✓ 已验证
DOI
高影响因子
CERAMICS INTERNATIONAL
·
2022
·
IF 5.532
Yan Zhao,Pengjun Zhao,Qing Zhao,Donglin He,Wenwen Kong,Bing Wu,Aimin Chang
Herein, Mg–Al–Si–Ba–O-based glass ceramics were studied as potential candidates to protect Mn–Co–Ni–O-based negative temperature coefficient (NTC) thermistors at high temperatures such as 900 °C. The ceramics were prepared in three glass formulations (1#: 15MgO–15Al 2 O 3 -44.7SiO 2 –25BaO, 2#: 17MgO–17Al 2 O 3 –41SiO 2 –25BaO and 3#: 17MgO–17Al 2 O 3 –41SiO 2 –20BaO–5Y 2 O 3 (in mol%)) and their glass-transition temperatures ( T g ) were determined using the differential scanning calorimetry (DSC) method. Scanning electronic microscopy (SEM) and X-ray diffraction (XRD) were used to characterize the parent glasses and glass-ceramic coatings. The sealing effects of the glass ceramics were examined by conducting an insulation test. The glass-ceramic sealing structures were subjected to 1000 thermal shock cycles at temperatures varying from room temperature to 900 °C. Notably, the sealing structure of glass-ceramic coating 1# was compact at a T g of 760.9 °C. The glass-ceramic coatings effectively maintained the NTC properties of the sensitive ceramics in all three formulations. Interestingly, the glass-ceramic coating 3# containing Y 2 O 3 demonstrated an increase in electrical resistance. Both the NTC thermistors coated with 1# and 2# glass formulations successfully passed 1000 thermal shock cycles without visible failures, and their resistance change ratios were well below the requisite 20%.
✓ 已验证
DOI
高影响因子
SURFACE & COATINGS TECHNOLOGY
·
2021
·
IF 4.158
Xiaoli Feng,Haifeng Wang,Xuechao Liu,Canming Wang,Hongzhi Cui,Qiang Song,Kun Huang,Neng Li,Xue Jiang
Inconel 625 + x Al ( x = 0, 2.5, 5.0, 7.5, 10.0) alloy coatings were prepared by laser cladding. The addition of Al promoted the formation of the BCC phase, which changed the coating microstructure from an FCC + δ phase + Laves phase to FCC + BCC + δ phase + Laves phase. Inconel 625 + 2.5 Al alloy showed the greatest corrosion resistance among all samples. The formation of an Al 2 O 3 film improved the corrosion resistance of the coating, but excess Al decreased the Cr 2 O 3 content in the film, which decreased the corrosion resistance of the coating. Increasing the Al content aggravated the lattice distortion and improved the solid solution strengthening effect, while also increasing the amount of BCC phase, which improved the coating hardness. After adding Al, the Inconel 625 + x Al alloy coatings displayed strong plastic deformation resistance, and their wear resistance was improved due to the presence of a hard phase.
✓ 已验证
DOI
高影响因子
JOURNAL OF CATALYSIS
·
2024
·
IF 6.5
Fuping Song,Juping Zhang,Dongfang Li,Tao Zhu,Xing Zhu,Hua Wang
Oxidative dehydrogenation (ODH) of ethylbenzene is a promising process for styrene production. However, its application is limited by product overoxidation and purification requirements due to the co-feeding of mild oxidants. Herein, we report a facile manganese-based catalyst (K/Mn 3 O 4 -Al 2 O 3 ) and achieve competitive styrene selectivity of 88 % and ethylbenzene conversion of 95 % at 450 ℃ (84 % yield vs. ∼ 60 % yield in commercial dehydrogenation process at 600 ℃) under a cyclic redox ODH scheme. The introduction of Al 2 O 3 into MnO x restructures composite oxides and depresses bulk lattice-oxygen migration for the partial oxidation of ethylbenzene. The surface modification using potassium creates reactive sites and regulates surface properties, achieving ethylbenzene activation and high conversions. Highly active lattice oxygen in catalysts after bulk and surface modifications selectively converts ethylbenzene to styrene and water. This study provides an understanding of roles of manganese-based catalysts in styrene generation and offers a strategy to modulate lattice oxygen on catalysts.
✓ 已验证
DOI
高影响因子
CORROSION SCIENCE
·
2024
·
IF 7.4
Zebang He,Zhong Wu,Zhiming Gao,Zhenbo Qin,Juntao Yuan,Yuan Gao,Yaorong Feng,Anqing Fu,Chun Wang,Wenbin Hu
A Ni-Al-Cu coating was prepared on NAB alloy through electroplating and heat treatment, and the erosion-corrosion behaviors were investigated. The results demonstrated that Ni-Al-Cu coating exhibited higher erosion resistance compared to NAB alloy, with an average reduction of 63 % in material removal rate (MRR). It was revealed that deformation and cracks were observed in NAB, with loss of hard κ and β phases alongside deformation of ductile α phase. Meanwhile, Ni-Al-Cu coating experienced fatigue delamination and grain disintegration due to alternating stress. Taguchi design method showed that increasing flow velocity and sand concentration could enhance the intensity of gravel impact, while changes in the erosion angle affected gravel impact modes and energy transfer, thereby impacting corrosion performance. Additionally, empirical equations for the material removal rate were derived through regression analysis, which became possible to predict the MRR under different influencing factors and assess the erosion-corrosion resistance of materials.
✓ 已验证
DOI
高影响因子
ACS Applied Nano Materials
·
2021
·
IF 5.097
Muhammad Amin Padhiar,Minqiang Wang,Yongqiang Ji,Zhi Yang,Yun Zhou,Hengwei Qiu,Hao Wang,Azaz Ali Shah,Arshad Saleem Bhatti
Perovskite nanocrystals (PNCs) are ideal for optical devices due to their adjustable emission band and high photoluminescence. However, blue light-emitting perovskite nanocrystals (PNCs) exhibit poor performance compared to their green and red-emitting PNC counterparts. Herein, we introduce a simple strategy for increasing the stability of blue light-emitting CsPb (Br/Cl)3 PNCs passivated with an Al-doped CdSe layer. This simple strategy successfully achieves highly stable PNCs with photoluminescence (PL) emission ranging from 454 to 460 nm with a full width at half-maximum (FWHM) ranging from 18 to 22 nm; changes in bandgaps are also observed, and the corresponding PLQY values show a significant change after CdSe/Al modification. In addition, CsPb (Br/Cl)3 PNCs with a CdSe layer doped with Al formed on the surface show remarkable stability under ambient conditions, including thermal exposure, water resistance, and ultraviolet (UV) irradiation. A light-emitting diode (LED) device was constructed to demonstrate the feasibility of the approach by combining the optimal CsPb(Br/Cl)3/CdSe/Al PNCs with an existing commercial 365 nm UV chip, resulting in bright blue light emission with CIE color coordinates of (0.16, 0.09). All of the findings suggest that doped CsPb (Br/Cl)3/CdSe/Al PNCs have the potential to be used as color converters in liquid crystal displays (LCDs).
✓ 已验证
DOI
高影响因子
危险品化学品经营许可证（带存储）