CERAMICS INTERNATIONAL
·
2022
·Vol. 48
·期 22
·33455-33461
·
IF 5.532
Yuyu Liu,Wenye Deng,Xianghui Chen,Yan Xue,Xuelian Bai,Huimin Zhang,Aimin Chang,Yongxin Xie
A series of novel high temperature negative temperature coefficient (NTC) composite ceramics based on (1- x )CaMn 0.05 Zr 0.95 O 3 - x NiMn 2 O 4 ( x = 0, 0.1, 0.2, 0.3) were fabricated by using the solid-state method. The Rietveld refinement method and backscattered electron (BSE) image confirmed the absence of any other phase. The conduction mechanism of the composite ceramics was determined by analyzing the complex impedance and resistance-temperature characteristics, which could be related to the formation of a continuous Mn 3+ -O-Mn 4+ network. The effect of spinel content on the high temperature stability was analyzed using aging tests. The ρ 400°C , ρ 700°C and B 400/700 values of the NTC thermistors were determined to be 4.9 × 10 6 –1.2 × 10 4 , 1.4 × 10 5 –0.8 × 10 3 Ω cm and 12739-5712 K, respectively. This indicated that the electrical properties could be tuned by adjusting the weight ratio of CaMn 0.05 Zr 0.95 O 3 and NiMn 2 O 4 . The findings obtained in this study reveal that the composite NTC thermistor exhibits a good application potential at high temperatures and under harsh environments.
研究领域:
材料科学
·
无机非金属材料
·
电子功能材料
·
固态离子学
·
高温传感器技术
✓ 已验证
DOI
高影响因子
APPLIED SURFACE SCIENCE
·
2022
·
IF 7.392
Baifeng Wu,Xiaofeng Wang,Xuefeng Xia,Qixin Wan,Yangsheng Li,Fan Li
The power conversion efficiency (PCE) of the perovskite solar cell (PSC) has made an illustrious breakthrough in the past ten years. However, it is still a great challenge to fabricate high-quality perovskite films due to the intrinsic high defect-density and internal non-radiative recombination, which has severely hindered the development of PSCs . Herein, a new-type additive guanidinium tetrafluoroborate (GuaBF 4 ) is introduced to improve the perovskite films quality, thus boosting photovoltaic performance of resultant PSCs . It is demonstrated that owing to the synergistic effect of Gua + and BF 4 − , the introduction of GuaBF 4 can improve the quality of CH 3 NH 3 PbI 3 (MAPbI 3 ) films. Through optimizing the concentration of GuaBF 4 , the MAPbI 3 film with GuaBF 4 displays higher crystallinity , enlarged crystal grain and smoother surface. Furthermore, by virtue of the strong interaction between MAPbI 3 and GuaBF 4 , the inclusion of GuaBF 4 can effectively passivate traps/defects in perovskite films, thereby diminishing the non-radiative recombination and promoting the charge carrier transportation. Consequently, a high-performance MAPbI 3 PSC with a PCE of 20.62 %, lessened hysteresis behavior and improved moisture stability is achieved. Our research emphasizes on the significance of the synergistic effect in additives for high-performance PSCs.
研究领域:
材料科学
·
能源科学
·
半导体器件
·
表面化学
·
光电子学
✓ 已验证
DOI
高影响因子
IONICS
·
2022
·Vol. 28
·期 11
·4943-4947
·
IF 2.961
Li Ze,Li Yonghua,Xie Huan,Zuo Zhaoyang,Chu Peng
As a kind of anode materials, iron matrix oxide cannot be widely used in the lithium-ion batteries due to their poor electrical conductivity and huge volume change during the electrochemical cycles. Herein, the porous carbon@Fe 2 O 3 composites are prepared by hydrothermal method. Due to the porous structure and introduction of carbon, the electrical conductivity can be greatly improved. Additionally, the porous structure could buffer the volume change during electrochemical cycles. As a result, the as-prepared carbon@Fe 2 O 3 composites deliver a high initial specific capacity of 1168 mAh/g at 0.1 C. Moreover, the carbon@Fe 2 O 3 composites show outstanding rate performance and superior cycling stability. This work provides a potential anode material for high electrochemical performance Li-ion batteries.
研究领域:
材料科学
·
电化学
·
能源存储
·
纳米材料
·
功能复合材料
✓ 已验证
DOI
高影响因子
CERAMICS INTERNATIONAL
·
2021
·Vol. 48
·期 6
·8579-8588
·
IF 4.527
Sunyi Shen,Shaolei Song,Jinming Wang,Rong Li,Xingchao Li,Qiang Zhen
Microstructure control and multiple compounding methods in the synthesis stage can enhance microwave absorption performance of microwave absorbents. In this work, we successfully synthesized binary TiB 2 –SiC (TsBC) powders with hexagonal sheet (TiB 2 ) and particle (SiC) interlocking structures by sol-gel carbothermal reduction method. We investigated the effect of raw material ratio and synthesis temperature on the synthesized powders and evaluated the microwave absorption properties of the synthesized TsBC powders. It was found that the TsBC absorber exhibited excellent microwave adsorption properties with the minimum Reflection Loss ( R L ) reached −21.8 dB at 17.4 GHz corresponding to the thickness of 4 mm. This excellent performance was attributed to the interfacial polarization between TiB 2 –SiC interfaces and the multiple reflections between the sheet-particle interlocking structures.
研究领域:
材料科学
·
功能材料
·
复合材料
·
电磁学
·
无机非金属材料
✓ 已验证
DOI
高影响因子
SURFACE & COATINGS TECHNOLOGY
·
2019
·
IF 3.192
Lu Zhu,Yousen Zhu,Xuanru Ren,Ping Zhang,Jianghao Qiao,Peizhong Feng
MoSi 2 -MoB-ZrO 2 composite powders are one-step synthesized prepared by self-propagating high-temperature synthesis (SHS), which are further utilized to prepare the oxidation protective coatings by spark plasma sintering (SPS) method on molybdenum substrate. Microstructure and properties of the coatings were investigated and determined. Oxidation behavior of the coatings at high temperature was also studied. The results showed that the composite coating is dense and crack-free due to the addition of ZrO 2 , which is beneficial for the decrease of mismatch in coefficient of thermal expansion, and no void exists in the diffusion layer owing to the diffusion of Si, which is inhibited by adding MoB. Compared with the pure MoSi2 coating, the high hardness of the composite coating is enhanced by about 20% while the fracture toughness of the composite coating is improved by about 25%, which makes the occurrence of intergranular fracture , crack deflection and crack bridging. After oxidation at 1400 °C for 80 h, MoSi 2 coating failed while xMoSi 2 -MoB-3ZrO 2 (x = 3, 4, 5) composite coating still kept its protective effect. Only a little substrate is consumed during oxidation and improved oxidation resistance is gained by MoSi 2 -MoB-ZrO 2 composite coating. 3MoSi 2 -MoB-3ZrO 2 coating shows the relatively best oxidation resistance due to the formation of crack-free oxide film on the surface of the coating.
研究领域:
材料科学
·
表面工程
·
高温氧化
·
陶瓷涂层
·
粉末冶金
✓ 已验证
DOI
高影响因子
INTERNATIONAL JOURNAL OF HYDROGEN ENERGY
·
2022
·Vol. 47
·期 83
·35352-35364
·
IF 7.139
Zhichao Yu,Wei Zhang,Yongxi Zhang,Yaokun Fu,Ying Cheng,Sanyang Guo,Yuan Li,Shumin Han
Magnesium hydroxide (MgH 2 ) has excellent reversibility and high capacity, and is one of the most promising materials for hydrogen storage in practical applications. However, it suffers from high dehydrogenation temperature and slow sorption kinetics. Rare earth hydrides and transition metals can both significantly improve the de/hydrogenation kinetics of MgH 2 . In this work, MgH 2 –Mg 2 NiH 4 –CeH 2.73 is in-situ synthesized by introducing Ni@CeO 2 into MgH 2 . The unique coating structure of Ni@CeO 2 facilitates homogeneous distribution of synergetic CeH 2.73 and Mg 2 NiH 4 catalytic sites in subsequent ball milling process. The as-fabricated composite MgH 2 -10 wt% Ni@CeO 2 powders possess superior hydrogenation/dehydrogenation characteristics, absorbing 4.1 wt% hydrogen within 60 min at 100 °C and releasing 5.44 wt% H 2 within 10 min at 350 °C. The apparent activation energy of MgH 2 -10 wt% Ni@CeO 2 is determined to be 84.8 kJ/mol and it has favorable hydrogen cycling stability with almost no decay in capacity after 10 cycles.
研究领域:
材料科学
·
无机化学
·
能源化学
·
纳米催化
·
氢能源存储
✓ 已验证
DOI
高影响因子
POLYMERS FOR ADVANCED TECHNOLOGIES
·
2023
·Vol. 34
·期 6
·1918-1932
·
IF 3.4
Yuqian Du,Xueya Wang,Ziwen Zhou,Feng Zhao,Song Li,Zhihua Liu,Zhengyu Wu,Shuai Zhao,Lin Li
Nowadays, although highly conductive polymer composites filled with two-dimensional graphene-based nano-fillers have been explored extensively, constructing nanocomposites with high performance, industrial feasibility, and more efficient conductive networks at lower nano-filler contents remains a challenge. To achieve the above objectives, industrial wastes microsilica powder (N98) with amorphous spherical structure and large particle size is employed in this work. And the hybrids (TGN) are obtained between N98 and graphene (GE) by the effective bridging and interface coupling of tannic acid, which can achieve the purpose of obtaining conductive composites with low-filler contents by traditional polymer processing technologies. The volume exclusion effect of N98 and its own assisted dispersion effect can prevent and attenuate graphene agglomeration, enabling the formation of a dense, complete and uniform conductive network in natural rubber (NR) matrix based on a small amount of graphene addition (parts per thousand). Thus, it give the nanocomposite highly functional, especially electric property. The results show that when the ratio of GE to N98 hybridization is 1:20, N98 and graphene are more uniformly hybridized together, and the volume exclusion effect is best matched with the rubber composites, and the comprehensive performance is optimal. Moreover, the electrical conductivity of NR/TG 1 N 20 nanocomposite can reach the balanced value of 10 −3 S·cm −1 with the GE loading of 0.48 phr, which shows the effectiveness of the prepared hybrids.
研究领域:
高分子科学
·
纳米复合材料
·
功能高分子
·
材料化学
·
导电聚合物
✓ 已验证
DOI
高影响因子
IONICS
·
2020
·Vol. 26
·期 9
·4257-4265
·
IF 2.394
Jiang Huize,Han Yu,Wang Hui,Zhu Yuhao,Guo Qingpeng,Jiang Haolong,Zheng Chunman,Xie Kai
The poor interface between the active materials, solid electrolytes, and conductive additives in composite cathode materials is the key factor restricting the performance of the all-solid-state lithium-sulfur battery. Here, the composite cathode material was prepared through the method of one-step ball milling. The sulfide electrolyte Li 3 PS 4 (LPS) was formed on the surface of the active material Li 2 S while the conductive additives were incorporated, and the conductive ions and electronic network were constructed simultaneously. After adding an appropriate amount of carbon nanotubes (cnt), the composite cathode exhibited high specific capacity of 1145.2 mAh g −1 after 30 times of cycling at a current density of 0.2 mA cm −2 , and the battery with ultrahigh areal Li 2 S loading also displays high capacity of 962.6 mA g −1 . The composite cathode with high Li 2 S content (56.3%) was prepared, with excellent performance exhibited: the capacity is 741 mAh g −1 after 30 times of cycling at a current density of 0.2 mA cm −2 .
Without additional sulfide electrolyte, the composite cathode materials were prepared by one-step ball milling with lithium sulfide, phosphorus pentasulfide, acetylene black, and carbon nanotubes as raw materials.
研究领域:
材料科学
·
电化学
·
能源存储
·
固态离子学
·
纳米复合材料
✓ 已验证
DOI
高影响因子
Advanced Optical Materials
·
2022
·Vol. 10
·期 13
·2200276
·
IF 10.05
Chenwei Liu,Yongjie Liu,Shuxin Wang,Jiwei Liang,Cheng Wang,Fang Yao,Weijun Ke,Qianqian Lin,Ti Wang,Chen Tao,Guojia Fang
Quasi-two-dimensional (quasi-2D) perovskite light-emitting diodes (PeLEDs) are considered as one of the most potential candidates in electroluminescence territory owing to their unique quantum confinement effect and excellent thermal stability of the light. Nevertheless, heterogeneous energy domain distribution leads to severe non-radiative recombination in the process of energy transfer, which enormously hinders the performance and application of PeLEDs. Herein, an ambipolar amino acid, 5-aminovaleric acid (5AVA), is demonstrated to be able to coordinate lead and halides simultaneously with its carboxyl and amidogen groups. The coordinated ambipolar molecule not only reconstitutes energy domains of perovskites but also minimizes the interfacial defects of PeLEDs. Accordingly, the presence of 5AVA in perovskite precursors leads to dramatic suppression of the n = 1 and n = 2 phases and accelerates energy transfer from wide bandgap domains to narrow bandgap ones. As a result, maximum external quantum efficiency (EQE) of 19.3% (18.20% ± 1.10%) is achieved in quasi-2D green PeLEDs with current efficiency of 61.7 cd A −1 .
研究领域:
材料科学
·
光电子学
·
纳米科技
·
半导体器件
·
凝聚态物理
✓ 已验证
DOI
高影响因子
Journal of Energy Chemistry
·
2020
·
IF 7.216
Jingguang Yi,Dan Zhou,Yuhao Liang,Hong Liu,Haifang Ni,Li-Zhen Fan
All-solid-state lithium batteries (ASSLBs) employing sulfide electrolyte and lithium (Li) anode have received increasing attention due to the intrinsic safety and high energy density. However, the thick electrolyte layer and lithium dendrites formed at the electrolyte/Li anode interface hinder the realization of high-performance ASSLBs . Herein, a novel membrane consisting of Li 6 PS 5 Cl (LPSCl), poly(ethylene oxide) (PEO) and Li-salt (LiTFSI) was prepared as sulfide-based composite solid electrolyte (LPSCl-PEO3-LiTFSI) (LPSCl:PEO = 97:3 wt/wt; EO:Li = 8:1 mol/mol), which delivers high ionic conductivity (1.1 × 10 −3 S cm −1 ) and wide electrochemical window (4.9 V vs. Li + /Li) at 25 °C. In addition, an ex-situ artificial solid electrolyte interphase (SEI) film enriched with LiF and Li 3 N was designed as a protective layer on Li anode (Li(SEI)) to suppress the growth of lithium dendrites. Benefiting from the synergy of sulfide-based composite solid electrolyte and ex-situ artificial SEI, cells of S-CNTs/LPSCl-PEO3-LiTFSI/Li(SEI) and Al 2 O 3 @LiNi 0.5 Co 0.3 Mn 0.2 O 2 /LPSCl-PEO3-LiTFSI/Li(SEI) are assembled and both exhibit high initial discharge capacity of 1221.1 mAh g −1 (135.8 mAh g −1 ) and enhanced cycling stability with 81.6% capacity retention over 200 cycles at 0.05 C (89.2% over 100 cycles at 0.1 C). This work provides a new insight into the synergy of composite solid electrolyte and artificial SEI for achieving high-performance ASSLBs .
研究领域:
材料科学
·
电化学
·
能源存储
·
固态电池
·
界面工程
✓ 已验证
DOI
高影响因子
APPLIED SURFACE SCIENCE
·
2016
·
IF 3.15
Qiang Huang,Meiying Liu,Junyu Chen,Ke Wang,Dazhuang Xu,Fengjie Deng,Hongye Huang,Xiaoyong Zhang,Yen Wei
Surface modification of nanomaterials with polymers is an effective route to render new functions and improve the performance of the final nanocomposites. Here, a facile method was developed to fabricate polyacrylic acid (PAA)-grafted monodisperse SiO 2 nanoparticles (SiO 2 -PDA-PAA) through a combination of mussel inspired chemistry and Michael addition reaction. To obtain the products, the SiO 2 nanoparticles were first coated with polydopamine (PDA) through self-polymerization of dopamine under rather mild conditions. The PDA thin films can then be further conjugated with amino-terminated PAA, which was synthesized by chain transfer free radical polymerization using cysteamine hydrochloride as a chain transfer agent and acrylic acid as a monomer. The SiO 2 -PDA-PAA nanocomposites were characterized via transmission electron microscopy, Fourier transform infrared spectroscopy, thermal gravimetric analysis, and X-ray photoelectron spectroscopy. The effects of contact time, solution pH, temperature and methylene blue (MB) concentration on the removal of MB were investigated. The results demonstrated that SiO 2 -PDA-PAA showed significant improvement in adsorption efficiency towards MB. The kinetics and isotherm studies showed that pseudo-second-order and Langmuir isotherm models were well fitted the experimental data. The values of thermodynamics parameters such as entropy change ( ΔS 0 ), enthalpy change ( ΔH 0 ) and Gibbs free energy ( ΔG 0 ) were calculated based on the Van’t Hoff equation. The negative values of thermodynamic parameters indicated that the adsorption of MB was a feasible, spontaneous and exothermic process. In summary, we developed a facile method to fabricate SiO 2 -based polymer nanocomposites, which showed obviously enhanced adsorption capability towards MB.
研究领域:
材料科学
·
环境化学
·
纳米技术
·
高分子化学
·
胶体与界面化学
✓ 已验证
DOI
高影响因子
MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING
·
2017
·
IF 3.094
Xinjiang Zhang,Feng Song,Zhiping Wei,Wenchao Yang,Zhongkui Dai
In-situ TiC/Ti titanium matrix composites were successfully fabricated through a novel approach, utilizing the reaction of graphene and Ti mixture powders in spark plasma sintering . Microstructure, hardness and compressive properties of such composites were investigated. The layered graphene nanosheets as the carbon source were dispersed in the powders, and subsequently formed uniform TiC particles in Ti matrix during the rapid sintering. The resulting TiC particles exhibited the micro- and nano-sized equiaxial structures. Such composites possessed the significantly enhanced hardness and room-temperature compressive strength comparing with the as-cast and as-sintered pure Ti. The ultimate and yield compressive strengths of as-prepared 7.0 vol% TiC incorporated composite respectively reached up to 2.64 GPa and 1.93 GPa, beyond some advanced Ti materials reported to date. In-situ micro- and nano-sized TiC particles were believed to be beneficial to harden and strengthen Ti matrix. The relevant strengthening mechanisms of such composites were discussed.
研究领域:
材料科学
·
金属基复合材料
·
粉末冶金
·
力学性能
·
显微结构表征
✓ 已验证
DOI
高影响因子
危险品化学品经营许可证（带存储）