COLLOIDS AND SURFACES A-PHYSICOCHEMICAL AND ENGINEERING ASPECTS
·
2019
·
IF 3.131
Xiaotong Sun,Luting Yan,Runxiang Xu,Mingyuan Xu,Yanyun Zhu
TiO 2 presents a broad application prospect in the field of degradation of environmental pollutants. However, the development of TiO 2 photocatalyst has been limited by two factors, namely, narrow spectral response range and low quantum efficiency . Surface coating can selectively change the physical and chemical properties of core particles, whereas the synergistic action between core and shell can optimize material performance. In this paper, surface modification of titanium dioxide (TiO 2 ) by dopamine polymerization was used to improve its photocatalytic performance. Among polydopamine (PDA)-modified TiO 2 , TiO 2 @PDA-0.4 mg/mL-2 h showed the best degradation rate of Rhodamine B (RhB): the degradation rate reached 99.28% and 77.40% after 1.5 h of ultraviolet–visible (UV–vis) and visible (Vis) light irradiation, respectively. Compared with the uncoated TiO 2 , the degradation rate has shown improvement, especially under Vis light irradiation, with the photocatalytic performance improving by 35.04%. Absorption, emission, and impedance spectra showed that surface modification of TiO 2 with suitable thickness of PDA effectively increased light absorption and promoted separation of photogenerated carriers . High-performance liquid chromatography–mass spectrometry revealed the differences in photocatalytic degradation mechanism of TiO 2 @PDA to RhB under UV–vis and Vis light irradiation. Compared with those under UV–vis light irradiation, the intermediate products under Vis light irradiation are relatively simple. TiO 2 @PDA generated more electrons, which interacted with H 2 O to produce large amounts of ·OH and holes under UV–vis light irradiation in comparison with that under Vis light irradiation. In addition to deacetylation , deamination , and decarboxylation by hydroxylation , excess ·OH in the photocatalytic process would attack benzene rings directly to produce N , N -diethylacetamide.
研究领域:
材料科学
·
环境化学
·
光催化
·
纳米材料
·
表面工程
✓ 已验证
DOI
高影响因子
JOURNAL OF SOLID STATE CHEMISTRY
·
2019
·
IF 2.291
Yuanbo Xie,Fangyuan Zhong,Hongxu Chen,Danni Chen,Jiawen Wang,Junkuo Gao,Juming Yao
In this paper, novel hydrogen-bonded metal-complex frameworks MPM-1-TIFSIX and HOF-21 were selected as adsorbents to adsorb iodine. MPM-1-TIFSIX and HOF-21 were prepared by layering method and mixed stirring method, respectively. The structures of the two HOFs were characterized in detail by XRD , BET, TGA and FT-IR. The adsorption behavior and adsorption capacity of MPM-1-TIFSIX and HOF-21 for iodine were investigated in detail. The experimental data showed that the equilibrium adsorption amounts of MPM-1-TIFSIX and HOF-21 were 205.51 mg/g and 172.86 mg/g, respectively. The adsorption process of MPM-1-TIFSIX was conformed to be pseudo-second-order kinetic, while the adsorption process of HOF-21 was conformed to be pseudo-first-order kinetic. The results indicated that HOFs could be used as iodine capture and storage materials.
研究领域:
材料化学
·
环境化学
·
配位化学
·
多孔材料
·
吸附科学
✓ 已验证
DOI
高影响因子
POLYMERS FOR ADVANCED TECHNOLOGIES
·
2016
·Vol. 27
·期 11
·1501-1507
·
IF 1.823
Zhubo Liu,Bing Zhou,A.V. Rogachev,M.A. Yarmolenko
Polytetrafluoroethylene (PTFE) composite coatings doped copper acetate and polyurethane (PU) were prepared on rubber substrate by low-energy electron beam dispersion technique. The effects of dopant and glow discharge treatment on the surface morphology, structure and tribological properties of the coatings were investigated. The results showed that Cu–PTFE composite coatings form uniform surface and dense column structure with spherical aggregations under glow discharge treatment. PU coating shows the large size of protuberance structure but PU–PTFE coating presents spherical structure. Both of the coatings become relative dense and smooth after discharge treatment, and Cu–PU–PTFE composite coatings possess a smoother surface and lower polar component of surface energy. Cu doping weakens the crystallinity and ordering degree of composite coatings, but glow discharge increases the ordering degree and branched structure of C―H groups. Friction experiment indicated that Cu fails to improve the wear resistance of PTFE coatings but glow discharge treatment can do it. Cu–PU–PTFE coatings after discharge treatment have the higher wear resistance and lower coefficient of friction. Copyright © 2016 John Wiley & Sons, Ltd.
研究领域:
材料科学
·
表面工程
·
高分子材料
·
摩擦学
·
等离子体物理
·
涂层技术
✓ 已验证
DOI
高影响因子
CHINESE JOURNAL OF CATALYSIS
·
2021
·Vol. 42
·期 10
·1798-1807
·
IF 8.271
Xiangyong Zhang,Tianying Liu,Ting Guo,Xueying Han,Zongyun Mu,Qiang Chen,Jiangmin Jiang,Jing Yan,Jiaren Yuan,Dezhi Wang,Zhuangzhi Wu,Zongkui Kou
Controllably mounting foreign atoms on the surfaces of earth-abundant electrocatalysts strongly improve their surface electronic properties for optimizing the catalytic performance of surficial sites to an unusual level, and provides a good platform to gain deep insights into catalytic reactions . The present work describes, employing ultrafine W 2 C nanoislands (average size: 2.3 nm) monodispersed on the N, P dual-doped carbon frameworks as a model system, how to regulate the atomic phosphorous-mounting effect on the surfaces of W 2 C to derive an active and stable P-mounting W 2 C (WCP) catalyst for both acidic and alkaline hydrogen evolution reaction (HER). Since in situ phosphorus substitution into carbon sites of preformed W 2 C nanoislands gradually proceeds from surfaces to solids, so that using a proper amount of phosphorus sources can readily control the surface mounting level to avoid the mass P-doping into the bulk. By this way, the activity per active site of WCP catalyst with robust stability can be optimized to 0.07 and 0.56 H 2 s −1 at –200 mV overpotential in acid and base, respectively, which reach up to the several-fold of pure-phase W 2 C (0.01 and 0.05 H 2 s −1 ). Theoretical investigations suggest that compared with solid P doping, the P mounting on W 2 C surface can more remarkably enhance its metallicity and decrease the hydrogen release barrier. This finding disclosed a key correlation between surface foreign atom-mounting and catalytic activity , and suggested a logical extension to other earth-abundant catalysts for various catalytic reactions .
研究领域:
材料化学
·
电催化
·
纳米材料
·
能源科学
·
表面科学
·
理论计算
✓ 已验证
DOI
高影响因子
JOURNAL OF PHYSICS AND CHEMISTRY OF SOLIDS
·
2018
·
IF 2.207
Hongyu Shi,Na Li,Zhixia Sun,Tianqi Wang,Lin Xu
TiO 2 nanoparticles are commonly used as versatile precursors to make functional nanocomposite materials. However, the surface defects at grain boundaries of TiO 2 nanoparticles significantly affect the photoelectric properties of TiO 2 nanomaterials . In this work, we firstly prepared nanocomposites of TiO 2 and polyoxometalates (POMs) in which different POMs, including titanium-substituted POMs K 5 [PW 11 TiO 40 ] and K 7 [PW 10 Ti 2 O 40 ], are incorporated with TiO 2 nanoparticles so as to make an interface modification on grain boundaries of TiO 2 nanoparticles. Then the photoconductivities of the TiO 2 /POM nanocomposites were investigated through measurement of photocurrent responses, current-voltage curves, Mott-Schottky plots and surface photocurrent spectra. Compared with pure TiO 2 nanoparticles, TiO 2 /POM nanocomposites exhibit superior photoelectric properties, benefitting from the interface modification from different POMs. The gas sensing performance for acetone was also explored by use of the as-prepared photoconductive devices, and TiO 2 /PW 11 Ti exhibited a high gas sensing performance.
研究领域:
材料科学
·
纳米科技
·
半导体物理
·
传感器技术
·
光电子学
✓ 已验证
DOI
高影响因子
JOURNAL OF MATERIALS SCIENCE
·
2017
·Vol. 52
·期 19
·11701-11714
·
IF 2.599
Wei Xiuzhen,Hong Jialiang,Zhu Shuangshuang,Chen Jinyuan,Lv Bosheng
Polyethyleneimine (PEI) of various molecular weights and trimesoyl chloride (TMC) were utilized to prepare composite nanofiltration (NF) membranes via interfacial polymerization. The changes in the surface structure and chemical composition of the prepared membranes were evaluated using SEM, ATR-FTIR, XPS and surface potential measurements. The pure-water flux and rejection rates of the inorganic salts (MgCl 2 , MgSO 4 , Na 2 SO 4 and NaCl) through the resultant NF membranes were also investigated. The results showed that the performance of the composite NF membranes was significantly affected by the molecular weight of the PEI. Notably, the permeate flux and rejection rate of the NF membranes increased with the PEI molecular weight. In addition, when the NF membranes were used to treat actual wastewater from the electroplating industry, the NF membranes presented high-efficiency separation properties for heavy metal ions. The rejection rates of the NF membranes at 0.4 MPa for chromium, nickel, zinc and copper ions reached 92.6, 89.6, 89.2 and 86.3%, respectively.
研究领域:
材料科学
·
膜分离技术
·
环境工程
·
高分子化学
·
水处理
✓ 已验证
DOI
高影响因子
APPLIED PHYSICS A-MATERIALS SCIENCE & PROCESSING
·
2023
·Vol. 129
·期 10
·682
·
IF 2.7
Yin Chunmei,Li Qinghua,Lu Zhiyi,Shi Yaochen,Lin Wei
A highly sensitive pressure-sensitive sensor based on MXene was developed using the electrostatic self-assembly method, with carbide sponges as the elastic substrate and a rational design. Specifically, CTAB was used to treat the carbide triamine sponge and conduct the electrostatic self-assembly with MXene to achieve a tightly combined conductive filler and substrate. The resulting pressure sensor showed excellent performance, with a high sensitivity of 15.05 kPa −1 under a range of 0–20 kPa, a response time of 0.1 s, and high durability under 2000 loading–unloading cycles. The minimum detection limit of the sensor was as low as 0.3 Pa, demonstrating excellent monitoring performance. Additionally, finite-element simulation analysis showed that MXene@CTAB@CMF had even better sensing performance at the same stress level. Moreover, the pressure sensor exhibited good sensing performance for various physiological signals and daily work monitoring of the human body, indicating its potential application value.
研究领域:
生物医学工程
·
纳米医学
·
柔性电子学
·
传感技术
·
材料科学
✓ 已验证
DOI
高影响因子
JOURNAL OF MATERIALS CHEMISTRY
·
2012
·Vol. 22
·期 43
·22873-22880
·
IF 5.968
Xiwei Zhang,Xiujuan Zhang,Xiaozhen Zhang,Yuping Zhang,Liang Bian,Yiming Wu,Chao Xie,Yuanyuan Han,Yan Wang,Peng Gao,Liu Wang,Jiansheng Jie
The narrow indirect bandgap of Si hinders the full absorption and utilization of the solar light. Energy band engineering to the Si based photovoltaic devices is essential to address this problem. Here we report the fabrication of ZnSe nanoribbon (ZnSeNR)/Si nanowire (SiNW) p–n heterojunction arrays by directly growing or simply drop-casting the p-type ZnSeNRs on highly aligned n-type SiNW arrays. Phosphorus (P) was used as dopant to achieve robust p-type doping in the ZnSe nanostructures with a hole concentration as high as 6.5 × 1018 cm−3. Thanks to the matched bandgap and the light trapping arising from the one-dimensional (1D) array structure, the heterojunction arrays exhibited improved light absorption, particularly in the blue/UV wavelength range. Moreover, by taking advantage of the ohmic contact between graphene and p-ZnSeNR, heterojunction array solar cells with graphene transparent electrode were fabricated, giving rise to a power conversion efficiency of ∼0.78% under AM 1.5G illumination. It was found that the surface passivation to the SiNW array played an important role in determining the device performance; an efficiency up to 2.27% was obtained after surface modification with methyl groups. Our results demonstrate the heterojunction arrays, together with the graphene transparent electrodes, could be promising candidates for high-performance and low-cost photovoltaic applications.
研究领域:
材料科学
·
纳米科技
·
半导体物理
·
光电子学
·
能源材料
·
表面科学
✓ 已验证
DOI
高影响因子
Small
·
2018
·Vol. 14
·期 31
·1801680
·
IF 9.598
Jiangjiang Zhang,Wenshu Zheng,Xingyu Jiang
Chemical regulation of enzyme-mimic activity of nanomaterials is challenging because it requires a precise understanding of the surface chemistry and mechanism, and rationally designed applications. Herein, Ag + -gated peroxidase activity is demonstrated by successfully modulating surface chemistry of cetyltrimethylammonium bromide-capped gold nanoparticles (CTAB-AuNPs). A surface blocking effect of long-chain molecules on surfaces of AuNPs that inhibit peroxidase activity of AuNPs is found. Ag + ions can selectively bind on the surfaces of AuNPs and competitively destroy CTAB membrane forming Ag + @CTAB-AuNPs complexes to result in enhanced peroxidase activity. Ag + @CTAB-AuNPs show the highest peroxidase activity compared to similar-sized citrate-capped and ascorbic acid-capped AuNPs. Ag + @CTAB-AuNPs can potentially develop into analyte-responsive systems and exhibit advantages in the optical sensing field. For example, the Ag + @CTAB-AuNPs system shows an enhanced sensitivity and selectivity for acetylcholinesterase activity sensing compared to other methods.
研究领域:
纳米生物技术
·
分析化学
·
酶学
·
生物传感器
·
分子诊断
·
转化医学
·
药物代谢
✓ 已验证
DOI
高影响因子
BIORESOURCE TECHNOLOGY
·
2016
·
IF 4.917
Hao Li,Samah Awadh Ali Mahyoub,Wenjie Liao,Shuqian Xia,Hechuan Zhao,Mengya Guo,Peisheng Ma
The magnetic biochars were easily fabricated by thermal pyrolysis of Fe(NO 3 ) 3 and distillation residue derived from rice straw pyrolysis oil at 400, 600 and 800 °C. The effects of pyrolysis temperature on characteristics of magnetic biochars as well as adsorption capacity for aromatic contaminants (i.e., anisole, phenol and guaiacol) were investigated carefully. The degree of carbonization of magnetic biochars become higher as pyrolysis temperature increasing. The magnetic biochar reached the largest surface area and pore volume at the pyrolysis temperature of 600 °C due to pores blocking in biochar during pyrolysis at 800 °C. Based on batch adsorption experiments, the used adsorbent could be magnetically separated and the adsorption capacity of anisole on magnetic biochars was stronger than that of phenol and guaiacol. The properties of magnetic biochar, including surface area, pore volume, aromaticity, grapheme-like-structure and iron oxide (γ-Fe 2 O 3 ) particles, showed pronounced effects on the adsorption performance of aromatic contaminants.
研究领域:
环境科学
·
环境工程
·
材料科学
·
物理化学
·
污染控制化学
·
能源材料
·
吸附科学
✓ 已验证
DOI
高影响因子
INDUSTRIAL CROPS AND PRODUCTS
·
2017
·
IF 3.181
Xinyan Yan,Zhaolan Zhai,Zhanqian Song,Shibin Shang,Xiaoping Rao
A series of polymeric surfactants , poly acrylic acid rosin polyethylene glycol esters (P-AAR-PEG), have been synthesized from natural diterpenic rosin. Their structures were characterized by Fourier Transform Infrared Spectrometer (FTIR) and their molecular weights were characterized by Gel Permeation Chromatography (GPC). Their critical micelle concentration (CMC), surface tension (γ CMC ), foaming property (FP), and hydrophile-lipophile balance (HLB) value were evaluated. Their thermal properties were measured by Thermal Gravimetric Analyzer (TGA) and fluid behaviors were studied by Rotational Rheometer. The influence of concentration on the properties of oil-in-water emulsions was examined and contrasted the stability of emulsion by the mean droplet size between day1 and day7. The weight-average molecular weight of P-AAR-PEG ranged from 1770 to 5071. CMC values of P-AAR-PEG were ranged from 0.33 to 0.87 g/L and the corresponding γ CMC values were ranged from 37.8 to 39.1 mN/m respectively. Their CMC and γ CMC values decreased and then increased with the increment of molecular weight of hydrophile group. Rheological measurements indicated that the P-AAR-PEG solutions changed from pseudoplastic property to Newtonian with increasing shear rate. P-AAR-PEG1000 had good emulsion ability to turpentine in water. When the concentration of P-AAR-PEG1000 was 8 wt%, the emulsion remained stable for more than 7 days.
研究领域:
高分子化学
·
表面与界面化学
·
材料科学
·
胶体化学
·
应用化学
✓ 已验证
DOI
高影响因子
INDUSTRIAL CROPS AND PRODUCTS
·
2022
·
IF 6.449
Min Guan,Xingye An,Hao Zhang,Guihua Yang,Zhongjian Tian,Shuangxi Nie,Liqin Liu,Zhengbai Cheng,Haibing Cao,Hongbin Liu
Global liquid packaging industry has been greatly spurred by the rapidly growing food & beverage industry all over the world. Liquid packaging board (LPB), as the main composition (75–80 %) of laminated liquid packaging cartons, must possess high-quality of hydrophobicity and physical properties for excellent leak-proof and protecting the packaged commodity. Herein, in this study, lignin is selected to prepare lignin cationic surfactant (LCS) by quaternary ammonium modification. Then cationic lignin modified rosin size ( L -CDRS) with uniform microsphere structure and high colloidal stability is successfully synthesized via a phase inversion process to improve the sizing performance and mechanical properties of LPB. The cation modified LCS presents improved amphipathicity of rich cationic charges and hydrophobic benzene ring skeleton, thus enhancing the electrostatic interactions between LCS and pulp fibers and improving the sizing performance of L -CDRS. The sizing performance of LPB is evaluated by varying the LCS dosages within L -CDRS and concluded that the edge penetration value and Cobb value of LPB handsheets exhibit an improved size performance with 2 % LCS within L -CDRS, implying the formation of homogeneous hydrophobic surface layer induced by the well-distribution of L -CDRS. In addition, the tensile index of LPB increased from 19.74 N·m/g to 25.96 N·m/g assisted by 2 % LCS emulsified L -CDRS, indicating an improved mechanical property. This study puts forward a practical and facile strategy to improve the sizing performance and mechanical properties facilitated by lignin enhanced rosin size and will further broaden the application range of traditional rosin size and lignin in LPB products.
研究领域:
造纸工程
·
高分子材料
·
表面化学
·
生物质利用
·
包装材料
✓ 已验证
DOI
高影响因子
危险品化学品经营许可证（带存储）