MATERIALS & DESIGN
·
2017
·
IF 4.364
Meng Fei,Renli Fu,Simeon Agathopoulos,Jun Fang,Caixia Wang,Haitao Zhu
A novel method for preparing aluminum/aluminum nitride ceramics (Al/AlN) substrates is proposed in this paper. The method included two processes: (1) the surface of AlN was coated with a CuO thick film and sintered; (2) Al foil was put on the pretreated (in process 1) AlN surface and bonded to AlN through pre-heating at 400 °C and final heating at 660 °C in N 2 -H 2 reduction atmosphere. The experimental results obtained by optical and scanning electron microscope (SEM) observations as well as by X-ray diffraction analysis at the cross-sections of the joints and the fracture surfaces , suggest that the reaction mechanism starts with the reaction of CuO with AlN to form CuAlO 2 , when the AlN coated with CuO is heat-treated at high temperature. A Cu layer is produced by the reduction of CuO and Cu diffuses in the Al foil, forming strong Al/AlN joints. Elongated crystals of Al 2 Cu are developed in the reaction zone at the interface between Al and AlN. The results of mechanical tests showed that the peeling-off strength of the Al foil from the surface of the AlN substrate reached a value of 15.4 MPa for the Al/AlN couples produced after 30 min of heat treatment at 660 °C.
研究领域:
材料科学
·
陶瓷工程
✓ 已验证
产品关联
DOI
高影响因子
SEPARATION AND PURIFICATION TECHNOLOGY
·
2024
·
IF 8.1
Peng Zu,Haoning Li,Guangming Yan,Gang Zhang
In this study, Ti 3 C 2 T x layers with an average lateral size of approximately 8.3 μm were prepared. The LLM composite membranes synthesized from these layers not only possessed long and narrow mass transfer channels but also further prevented the generation of internal non-selective defects. Additionally, a strategy of compositing these Ti 3 C 2 T x layers and Al(OH) 3 was adopted. The strategy contributed to expanding the interlayer distances of the composite membranes and adjusting the in-plane stacking order, thereby facilitating the construction of mass transfer channels characterized by high permeance within the membranes. This resulted in the preparation of LLMA membranes. Among these LLMA membranes, the LLMA-1:7 composite membranes displayed outstanding performance in the sieving process. Their permeances were more than 10 times higher than those of the LLM membranes (with a thickness of 1 μm). Also, the rejection ratio for CV dye could even exceed 99 %, and the operational stability was also significantly improved. These advantages enabled them to avoid some of the shortcomings commonly found in two-dimensional (2D) separation membranes to a certain extent. In summary, the LLMA-1:7 composite membranes designed in this study demonstrated superior overall performance, compared to the majority of the previously reported 2D membranes. This research is expected to establish a solid foundation for the application of 2D MXene membranes in the field of water treatment.
研究领域:
材料科学
·
环境工程
✓ 已验证
产品关联
DOI
高影响因子
JOURNAL OF WUHAN UNIVERSITY OF TECHNOLOGY-MATERIALS SCIENCE EDITION
·
2020
·Vol. 35
·期 3
·514-519
·
IF 0.64
Liu Tingling,Pang Xiaoxuan,Xian Yajiang,Luo Hao,Zhang Pengcheng
Aluminum-matrix boron carbide (B 4 C p /Al) is a kind of neutron absorbing material widely used in nuclear spent fuel storage. In order to improve the tensile property of B 4 C p /Al composites, a new type of nano-Al 2 O 3 particle (Al 2 O 3np ) reinforced B 4 C p /Al + Al 2 O 3np composites were prepared by powder metallurgy method. The Monte Carlo particle transport program (MCNP) was used to determine the influence of Al 2 O 3np on the thermal neutron absorptivity of composites. The universal material testing machine and scanning electron microscope (SEM) were used to study the mechanical properties, microstructure and fracture morphology of B 4 C p /Al composites. The results indicated that the neutron absorption properties of B 4 C p /Al composites were not affected by the addition of nano-Al 2 O 3 particles in the range of 1 wt%–15 wt%. The addition of Al 2 O 3np can obviously reduce the grain size of B 4 C p /Al matrix metals thus improve the tensile strength of the composites. The addition threshold of Al 2 O 3np is about 2.5 wt%. Both B 4 C p and Al 2 O 3np change the fracture characteristics of the composites from toughness to brittleness, and the latter is more important.
研究领域:
材料科学
·
核工程
✓ 已验证
DOI
高影响因子
Separations
·
2024
·Vol. 11
·期 1
·29
·
IF 2.5
Xiaoyu Xu,Jiahua Liu,Yuang Cao,Han Wang,Keqiang Zhang,Chein-Chi Chang,Suli Zhi
This study tried to use electroflocculating precipitated waste to prepare a Si@Al adsorbent by simply mixing sodium silicate at a mass ratio of 4:1 and calcining at 200 °C for 2 h. The adsorbent was low cost, high efficiency, and could remove a variety of contaminants (organic pollutants, antibiotics, and metal ions) from water. In this study, adsorbent characterization and pollutant adsorption experiments were carried out. The results showed that: Si@Al adsorbent had uniform particles, distinct layers, a loose porous appearance, and the internal structure was scattered without a crystal structure. The optimal adsorption conditions for tetracycline were as follows: dosage of adsorbent 2.0 g/L, reaction time 10 min, pH = 4.5, and tetracycline removal rate of 97.13%. The optimal adsorption conditions for MB (MB stands for methylene blue) were an adsorption dosage of 4.0 g/L, a reaction time of 15 min, pH = 4.5–8.5, and a removal rate of 96.39%. The optimal adsorption conditions for Cu were a 2.0 g/L dosage of adsorbent, a reaction time of 30 min, a pH of 8.5, and a highest removal rate of 97.47%. It was worth noting that the effect of temperature on TC, MB and Cu was not significant. At the same time, the kinetic fitting results showed that the adsorption of MB was more consistent with the quasi-second-order kinetic model, with R2ranging from 0.9788 to 1.0000. The adsorption of TC and Cu was more consistent with the quasi-first-order kinetic model, with R2ranging from 0.9598 to 0.9999 and 0.9844 to 0.9988, respectively. According to the results of thermodynamics, kinetics and zero potential point, the adsorption of tetracycline and methylene blue was mainly a physical adsorption, multilayer heterogeneous or single-layer homogeneous adsorption process. The adsorption of Cu was categorized as multi-layer heterogeneous chemical adsorption. The co-existing substances had little effect on the properties of the adsorbent, and the adsorbent could be recycled 5 times. Compared with other adsorbents, the results showed that the adsorbents had obvious advantages in terms of the raw material source, preparation method, time cost and removal effect. This study provided a “waste into treasure, green and efficient” multi-pollutant adsorption method.
研究领域:
环境科学
·
材料科学
✓ 已验证
产品关联
DOI
高影响因子
PHYSICA SCRIPTA
·
2024
·Vol. 100
·期 1
·015948
·
IF 2.6
Fucheng Yu,Zengguang Huang,Jinghong Zhang,Sihua Zhong
Cu3BiS3 has been considered as an attractive photovoltaic material due to its suitable bandgap, excellent photoelectric properties, abundant component elements and low toxicity. However, most of the reported Cu3BiS3 solar cells contain toxic components in other functioning layers such as CdS in electron-transport layers (ETLs). In this study, the Cu3BiS3 thin films were prepared by spin-coating method. We find that the CuCl concentration in precursor solutions has influences on both the optical bandgap and grain size of the Cu3BiS3 thin films, thus affecting the performance of solar cells. The optimal CuCl concentration is 0.91 M. Besides, Al doped TiO2 (ATO) and MoOx films are employed as ETLs and hole-transport layers (HTLs) respectively, constructing a totally non-toxic thin film solar cell. Moreover, it is demonstrated that the ratio (RAl:Ti) of Al source (Aluminum nitrate nonahydrate) to Ti source [Titanium diisopropoxide bis(acetylacetonate)] in the precursor solution of ATO and the thickness of MoOx have significant influences on solar cells. Moderate Al doping in ATO, e.g. RAl:Ti=1:50, can produce oxygen vacancies and accelerate the interfacial charge transfer, thus resulting in the increased short-circuit current density and fill factor. With the optimized Cu3BiS3 absorber, ETL and HTL, improved cell performances are observed comparted to the spin-coated Cu3BiS3 counterparts with CdS as ETLs in literature.
研究领域:
材料科学
·
能源科学
✓ 已验证
产品关联
DOI
高影响因子
SOLAR ENERGY MATERIALS AND SOLAR CELLS
·
2025
·
IF 6.3
Shuhui Chen,Jinjie Mo,Ziye Ling,Zhengguo Zhang,Xiaoming Fang
The propensity for leaks in high-temperature molten alloys greatly restricts their extensive use in storing high-temperature thermal energy. In tackling this matter, the research concentrates on Al-Si/AlN composite phase change materials (PCMs), incorporating the modifier Sb to significantly improve their heat conduction and thermal steadiness. The results reveal that incorporating Sb alters the Si phase from a bulk form to an elongated one, simultaneously triggering the creation of an Al-Si@Al 2 O 3 core-shell configuration. This structural optimization reduces free electron scattering and extends the mean free path of electrons, thereby improving the thermal conductivity of the material. It was established that the ideal fraction of Sb mass is 0.6 %, where the thermal conductivity of the Sb-altered Al-Si/AlN composite PCMs attains 49.5 W/(m·K), marking a 15.2 % enhancement over the original Al-Si/AlN composite PCMs, with a latent heat of 351.5 kJ/kg. Additionally, the creation of the Al 2 O 3 shell led to the altered materials showing remarkable thermal stability across 200 high-temperature thermal cycles, resulting in less than a 4 % decrease in latent heat post-cycle and no leakage detected. The study offers not just an innovative approach for creating advanced Al-Si/AlN composite PCMs but also broadens their use in storing thermal energy at high temperatures.
研究领域:
材料科学
·
能源工程
✓ 已验证
产品关联
DOI
高影响因子
JOURNAL OF PHYSICS AND CHEMISTRY OF SOLIDS
·
2024
·
IF 4.3
Shiqi Chen,Liu Yang,Jun Shen
This study evaluated electron shielding capabilities of various materials using Geant4 Monte Carlo software. By analyzing materials with different atomic numbers, we designed and tested composite films and coatings for radiation protection. Under 1.2 MeV electron irradiation, these materials reduced the dose deposited in electronic components by over 70 %. The fabricated composite films (W–Al) reduced the actual total dose by 100 % with a 30.67 % mass increase, closely matching the simulation result of 75.36 %. The composite coatings (W–Al) reduced the dose by 89.2 % with a 33 % mass increase, matching the simulation result of 70 %. Cascade collision simulations revealed that higher PKA energies lead to longer times to reach the thermal peak, more peak defects, and more stable defect pairs. This is due to the displacement threshold energy of the atoms in aluminum and tungsten. These results demonstrate the effectiveness of our composite films and coatings in enhancing electron shielding performance and validate our design methods.
研究领域:
航空航天工程
·
材料科学
·
辐射物理学
✓ 已验证
产品关联
DOI
高影响因子
MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING
·
2024
·
IF 6.1
Qiang Liu,Jiarui Yang,Guoqing Tian,Zhenhui Huang,Liying Shen,Chuyan Hu,Baihan Wang,Kaiyang Wang,Shuang Feng,Feng Ye
Materials with high specific strength and toughness are urgently needed in the fields of electronic packaging, armor, and aerospace. SiC/Al composites show good potential for these applications but the problem of mutual exclusion of strength and toughness still needs to be solved. Herein, we propose a new strategy to simultaneously enhance its strength and toughness from the perspective of structural optimization and interface enhancement. Inspired by the nacre structure, a 3D-(SiC–Si 3 N 4 )/Al co-continuous composite was prepared by freeze-casting combined with the pressure infiltration method. During the process, elongated Si 3 N 4 grains were introduced into the ceramic framework to design the internal lamella wall structure and increase the contact area with the aluminum substrate. Moreover, a favorable interfacial bonding was designed between Si 3 N 4 and Al to improve interface wettability . The reliable microstructure of porous 3D-(SiC–Si 3 N 4 ) preform was tailored through the adjustment of initial solid loading and the α-Si 3 N 4 component. The effects of initial solid loading and the α-Si 3 N 4 component on the microstructure, interfacial wettability, and mechanical properties of the final composites were investigated. The results showed that the SiC–Si 3 N 4 /Al composites possess high flexural strength (769 MPa) and fracture toughness (15.1 MPa m 1/2 ), which is superior to data reported in general literature. Numerous elongated β-Si 3 N 4 grains are produced on the ceramic skeleton, forming an interlocking structure with the aluminum matrix, which increases the contact area with the aluminum substrate. A chemical reaction layer was formed at the interface of the composite, greatly improving the interfacial bonding strength. This work provides a promising design guideline for developing and optimizing high-strength and tough composite.
研究领域:
材料科学
·
复合材料工程
✓ 已验证
产品关联
DOI
高影响因子
ACS Omega
·
2021
·
IF 3.512
Mingyu Zhang,Chaoyong Wang,Junkai Zhang,Gang Li,Li Gu
LiNi0.8Co0.1Mn0.1O2 (NCM811) became a research hot point because of its low cost, environmental friendliness, and excellent electrochemical performance. However, Li+/Ni2+ intermixing is an essential factor affecting its applicability. Doping could be an important method to improve the electrochemical performance of NCM811-based cathode materials. In this work, La and Al co-doped NCM811 was prepared by a solid-state method. Results from X-ray diffraction (XRD), scanning electron microscopy (SEM), and energy-dispersive spectroscopy (EDS) and electrochemical performance were discussed in depth. These showed that when La and Al doping concentrations were 1 and 0.5%, the samples showed the best performance. The as-improved performances were mainly attributed to the reduced Li+/Ni2+ intermixing, suppressed phase transition, and decreased potential polarization and impedance.
研究领域:
材料科学
·
电化学
✓ 已验证
产品关联
DOI
PubMed
高影响因子
INDUSTRIAL & ENGINEERING CHEMISTRY RESEARCH
·
2016
·
IF 2.567
Huimin Ruan,Changmeng Guo,Hongwei Yu,Jiangnan Shen,Congjie Gao,Arcadio Sotto,Bart Van der Bruggen
This study reports the fabrication of mixed matrix membranes (MMMs) using immersion precipitation phase inversion for promising application in desalination of dye solutions. Aromatic poly(m-phenylene isophthalamide) is used as the polymer material, and the metal–organic framework MIL-53(Al) is added to develop integrally skinned asymmetric membranes. Successful dispersion of MIL-53(Al) particles into the membrane-separating layer is confirmed by scanning electron microscopy. The optimum performance of the membranes is obtained at 0.5 wt % MIL-53(Al) concentration. In particular, the M-0.5 membrane is planned for use in separating dye/salt aqueous mixtures. It is observed that the M-0.5 membrane has a rejection for NaCl and Na2SO4 below 11% and 37%, respectively, in mixed salt/dye solutions. Additionally, the M-0.5 membrane is found to have a rejection rate of 83.9%, 98.3%, and 99.8% for nitroso-R salt, xylenol orange, and ponceau S, respectively, in mixed Na2SO4/dye solutions. The rejection rate for Na2SO4 is lower than that of some commercial nanofiltration membranes (NF90, NF270, and DK). The membrane is promising for dye desalination in industrial-scale applications.
研究领域:
材料科学
·
环境工程
✓ 已验证
产品关联
DOI
高影响因子
CHEMICAL ENGINEERING JOURNAL
·
2023
·
IF 15.1
Haifeng Yang,Zhiqiang Qiao,Weimiao Wang,Pengfei Tang,Shuaishuai Man,Xiaodong Li,YuTing Xie,Deyun Tang,Xueming Li,Guangcheng Yang
Private information protection of electronic chips which store large amounts of sensitive data, is a crucial issue in electromechanical systems nowadays. Here, a self-destructive microchip based on an instantaneous thermite reaction is designed to prevent the leakage of electronic information. The device is consisted of a silicon test wafer and an upper energetic film coated by a simple drop-casting technique. A series of Al/BiOX-based nanothermites have been prepared for decreasing the reaction sensitivity, meanwhile optimizing the destruction efficiency of the energetic film system. Among them, Al/Bi 2 O 3 nanothermite containing 30 wt% BiOBr possesses a low sensitivity (45 J), the maximum pressure peak (1.93 MPa) and pressure effect duration due to multiple interactions of the three nano-scale energetic components. Besides, the energetic film prepared by this nanothermite fomula also exhibits a more effective destruction of the device. The high-speed photography results demonstrate that the violent reaction shatters the thick energetic microchip (∼1 mm) within merely 0.5 ms. Importantly, the efficient destruction of energetic microchips shows excellent reproducibility in different working scenes, including Air or Ar atmosphere. It is believed that this self-destructive device with environmentally friendly components and simple but adaptive design can be extensively used in various electric microcomponents.
研究领域:
材料科学
·
电子工程
·
安全技术
✓ 已验证
产品关联
DOI
高影响因子
MOLECULES
·
2010
·Vol. 15
·期 8
·5139-5152
·
IF 1.738
Lu Lin,Ying Liu
A series of Ni-based catalysts were prepared using hydrogen reduction of Ni/Al hydrotalcite-like compounds (Ni/Al HTlcs) synthesized by coprecipitation. The physico-chemical properties of Ni/Al hydrotalcite-like compounds and the corresponding Ni-based catalysts were characterized using inductively coupled plasma (ICP), BET surface areas, X-ray diffraction (XRD), Fourier transform infrared (FTIR) spectroscopy and scanning electron microscopy (SEM) techniques. The results indicated that Ni/Al HTlcs with layered structures could be successfully prepared by the coprecipitation method, and the characteristic HTlcs reflections were also observed in the XRD analysis. The NiO and Ni0phases were identified in all Ni-based catalysts, which displayed randomly interconnected pores and no layer structures. In addition, the studies also found the Ni/Al HTlcs and Ni-based catalysts had high specific surface areas, low pore volumes and low pore diameters. The catalytic hydrogenation of ethyl acetate to ethanol with Ni-based catalysts was also investigated. Among the studied catalysts, RE1NASH-110-3 showed the highest selectivity and yield of ethyl acetate to ethanol, which were 68.2% and 61.7%, respectively. At the same time, a major by-product, butyl acetate, was formed due to an ester-exchange reaction. A proposed hydrogenation pathway for ethyl acetate over Ni-based catalysts was suggested.Keywords:hydrogenation;ethyl acetate;ethanol;Ni/Al hydrotalcite-like compounds
研究领域:
化学工程
·
催化化学
✓ 已验证
DOI
PubMed
高影响因子
危险品化学品经营许可证（带存储）