CHEMISTRY OF MATERIALS
·
2018
·
IF 9.89
Aizhao Pan,Jianli Wang,Matthew J. Jurow,Mengjun Jia,Ya Liu,Youshen Wu,Yanfeng Zhang,Ling He,Yi Liu
The potential optoelectronic applications of perovskite nanocrystals (NCs) are primarily limited by major material instability arising from the ionic nature of the NC lattice. Herein, we introduce a facile and effective strategy to prepare extremely stable CsPbX3 NC–polymer composites. NC surfaces are passivated with reactive methacrylic acid (MA) ligands, resulting in the formation of homogeneous nanocubes (abbreviated as MA-NCs) with a size of 14–17 nm and a photoluminescence quantum yield above 80%. The free double bonds on the surface then serve as chemically addressable synthetic handles, enabling UV-induced radical polymerization. Critically, a bromide-rich environment is developed to prevent NC sintering. The composites obtained from copolymerizing MA-NCs with hydrophobic methyl methacrylate and methacrylisobutyl polyhedral oligomeric silsesquioxane monomers exhibit enhanced properties compared to previously reported encapsulated NCs, including higher quantum yields, remarkable chemical stability toward water, and much enhanced thermal stability. The good solubility of the composite in organic solvent further enables its use as a solution-processable luminescent ink, used here for fabrication of white-light-emitting diodes with high luminous efficiency and excellent color-rendering index. The resulting fluorescent and stable NC ink opens the door to potential scalable and robust optoelectronic applications.
研究领域:
材料科学
·
光学工程
✓ 已验证
产品关联
DOI
高影响因子
ACS Applied Nano Materials
·
2023
·
IF 5.9
Yanchao Yu,Yuan Gao,Wenjuan Wang,Hanyang Chen,Yuzhe Yun,Seeram Ramakrishna,Jun Zhang,Yun-Ze Long
Traditional detection methods usually use a spectrometer, which requires a professional tester to operate and is not convenient to carry around. Herein, we designed a 5G smartphone-based portable test sensor that uses a CsPbBr3 composite fibrous membrane prepared by a one-step in situ growth method as the test paper, and the test is realized by taking pictures with the smartphone. This portable detection method requires only one drop of liquid to be detected (<25 μL), which is superior to many detection systems that require a large amount of liquid to be detected (>1 mL). Moreover, the detection sensitivity can reach 0.1 ppm, which is more sensitive than the CsPbBr3 composite fiber membrane prepared by the conventional encapsulated method. In addition, this CsPbBr3 composite fiber membrane is reusable and can still achieve highly sensitive detection with a single drop after 100 uses. This smartphone-based portable test sensor is small in size and easy to use and can be used at home or outdoors anytime and anywhere.
研究领域:
材料科学
·
分析化学
·
生物医学工程
✓ 已验证
产品关联
DOI
高影响因子
Advanced Energy Materials
·
2020
·Vol. 10
·期 22
·2000691
·
IF 25.245
Chenyang Duan,Jian Cui,Miaomiao Zhang,Yu Han,Shaomin Yang,Huan Zhao,Hongtao Bian,Jianxi Yao,Kui Zhao,Zhike Liu,Shengzhong (Frank) Liu
High temperature stable inorganic CsPbX 3 (X: I, Br, or mixed halides) perovskites with their bandgap tailored by tuning the halide composition offer promising opportunities in the design of ideal top cells for high-efficiency tandem solar cells. Unfortunately, the current high-efficiency CsPbX 3 perovskite solar cells (PSCs) are prepared in vacuum, a moisture-free glovebox or other low-humidity conditions due to their poor moisture stability. Herein, a new precursor system (HCOOCs, HPbI 3 , and HPbBr 3 ) is developed to replace the traditional precursors (CsI, PbI 2 , and PbBr 2 ) commonly used for solar cells of this type. Both the experiments and calculations reveal that a new complex (HCOOH•Cs + ) is generated in this precursor system. The new complex is not only stable against aging in humid air ambient at 91% relative humidity, but also effectively slows the perovskite crystallization, making it possible to eliminate the popular antisolvent used in the perovskite CsPbI 2 Br film deposition. The CsPbI 2 Br PSCs based on the new precursor system achieve a champion efficiency of 16.14%, the highest for inorganic PSCs prepared in ambient air conditions. Meanwhile, high air stability is demonstrated for an unencapsulated CsPbI 2 Br PSC with 92% of the original efficiency remaining after more than 800 h aging in ambient air.
研究领域:
材料科学
·
太阳能
·
化学工程
✓ 已验证
产品关联
DOI
高影响因子
ACS Applied Nano Materials
·
2021
·
IF 5.097
Muhammad Amin Padhiar,Minqiang Wang,Yongqiang Ji,Zhi Yang,Yun Zhou,Hengwei Qiu,Hao Wang,Azaz Ali Shah,Arshad Saleem Bhatti
Perovskite nanocrystals (PNCs) are ideal for optical devices due to their adjustable emission band and high photoluminescence. However, blue light-emitting perovskite nanocrystals (PNCs) exhibit poor performance compared to their green and red-emitting PNC counterparts. Herein, we introduce a simple strategy for increasing the stability of blue light-emitting CsPb (Br/Cl)3 PNCs passivated with an Al-doped CdSe layer. This simple strategy successfully achieves highly stable PNCs with photoluminescence (PL) emission ranging from 454 to 460 nm with a full width at half-maximum (FWHM) ranging from 18 to 22 nm; changes in bandgaps are also observed, and the corresponding PLQY values show a significant change after CdSe/Al modification. In addition, CsPb (Br/Cl)3 PNCs with a CdSe layer doped with Al formed on the surface show remarkable stability under ambient conditions, including thermal exposure, water resistance, and ultraviolet (UV) irradiation. A light-emitting diode (LED) device was constructed to demonstrate the feasibility of the approach by combining the optimal CsPb(Br/Cl)3/CdSe/Al PNCs with an existing commercial 365 nm UV chip, resulting in bright blue light emission with CIE color coordinates of (0.16, 0.09). All of the findings suggest that doped CsPb (Br/Cl)3/CdSe/Al PNCs have the potential to be used as color converters in liquid crystal displays (LCDs).
研究领域:
材料科学
·
光学工程
✓ 已验证
DOI
高影响因子
Materials Today Chemistry
·
2025
·
IF 6.7
Wenbin Shi,Xiao Zhang,Ping Yang
Small CsPbBr 3 and CsPbI 3 nanocrystals (NCs) with tunable sizes and high photoluminescence (PL) were prepared by ligand (Dodecylbenzenesulfonic acid (DBSA)) derived slow growth and surface passivation to decrease structure and surface defects. Namely, the powerful binding of sulfonic acid groups with Pb 2+ and the steric hindrance effect of benzene rings are the key for the preparation of small-sized NCs. The minimum size of CsPbBr 3 NCs is approximately 2.28 nm. Meanwhile, the PL peaks of CsPbBr 3 and CsPbI 3 NCs are adjustable from 461 to 516 nm and 660–685 nm, respectively. The treatment of CsPbX 3 NCs by ZnX 2 (X = Br and I) effectively passivated halide vacancies. The PL quantum yields (PLQYs) reach to 93.8 % for blue-emitting CsPbBr 3 NCs and 89.6 % for red-emitting CsPbI 3 NCs. The strong binding of DBSA to Pb ions enabled small NCs to maintain their initial PL intensity of 80 % after storage for 130 days and ultraviolet light irradiation for 140 min. The ZnX 2 (X = Br and I) treatment did not change the structural stability of CsPbX 3 NCs. Finally, CsPbBr 3 and CsPbI 3 NCs were applied to fabricate white light emitting diodes (LEDs). The color coordinates, as defined by the Commission Internationale de l'Eclairage, are positioned at (0.34, 0.33), accompanied by a correlated color temperature measuring 4441 K, which highlights the successful production of warm white LEDs. This result provides an efficient way for creating CsPbBr 3 NCs with blue emitting and CsPbI 3 with red emitting in short wavelength region.
研究领域:
材料科学
·
光学
·
化学工程
✓ 已验证
产品关联
DOI
高影响因子
JOURNAL OF LUMINESCENCE
·
2024
·
IF 3.3
Junhu Cai,Xiang Zhang,Yu Chen,Wenzong Lai,Wenyan Zhang,Zexi Lin,Yun Ye,Sheng Xu,Tailiang Guo,Jiajun Luo,Enguo Chen
Inorganic metal halide perovskite quantum dots (PQDs) have recently emerged as promising candidates for color conversion materials in Micro-LED displays, due to their outstanding color purity, high absorption coefficient, tunable emission wavelength . However the inferior stability and undesirable photoluminescence quantum yield (PLQY) restrict their particle applications. Herein, CsPbX 3 /PMMA (X = Br, I) composites with improved stability and optical performance were successfully prepared by a general and mild in-situ polymerization strategy. The ester carbonyl (C O) group in MMA formed complexes with Pb 2+ , leading to the in-situ thermal polymerization of polymethyl methacrylate (PMMA) under the action of the initiator. The multifunctional PMMA can efficiently passivate halogen vacancies while acting as a barrier against the degradation caused by heat, water, and oxygen. As a result, the PLQYs and stability of PMMA-coated CsPbX 3 PQDs have been significantly improved. When implementing CsPbX 3 /PMMA/PDMS composites as color conversion layers in Micro-LEDs, they achieve an impressive color gamut of 127.23% with excellent stability. We believe our work will stimulate the exploration of perovskite/polymer composites for industrial Micro-LED applications.
研究领域:
材料科学
·
光学工程
·
显示技术
✓ 已验证
DOI
高影响因子
CHEMISTRY-A EUROPEAN JOURNAL
·
2017
·Vol. 24
·期 8
·1898-1904
·
IF 5.317
Shaofan Fang,Guangshe Li,Yantong Lu,Liping Li
Graphical Lifting the curse : We reported on a novel route by using solid metal halides as halide sources that achieve an anion exchange with CsPbX 3 without any pretreatment. Introducing small amounts of oleic acid or oleylamine speed up the exchange reaction rate, although showing different promotion mechanisms (see figure). Cesium lead halide perovskite (CsPbX 3 ) nanocrystals (NCs) exhibit an excellent photoelectric performance, which is directly governed by fine-tuning of the composition and preparation of materials with a special phase structure and morphology. However, it is still facing challenges to achieve highly stable and luminescent CsPbX 3 NCs at room temperature. Herein, we report on a novel exchange reaction, in which metal halides MX 2 (M=Zn, Mg, Cu, or Ca; X=Cl, Br, or I) solids act as anion source to directly prepare CsPbX 3 NCs at room temperature without any pretreatment. Introducing small amount of oleic acid or oleylamine speed up the exchange reaction through different promotion mechanisms. Oleic acid coordinates to the surface of the NCs, which increases the reaction activity, and oleylamine greatly enhances the dissolution of ZnCl 2 . XRD and TEM tests demonstrate that the cubic phase structure and the morphology of the parent CsPbX 3 were well preserved. Moreover, the band-gap energies and photoluminescence (PL) spectra were readily tunable over the entire visible spectral region of λ =406–685 nm. Our findings could open up the possibilities of using metal halide solids as new anion sources to prepare high-quality CsPbX 3 NCs at room temperature.
研究领域:
材料科学
·
化学
✓ 已验证
产品关联
DOI
PubMed
高影响因子
Optical Materials Express
·
2018
·Vol. 8
·期 11
·3494-3505
·
IF 2.566
Yujun Xie,Yan Yu,Junyi Gong,Cheng Yang,Pan Zeng,Yurong Dong,Bilin Yang,Rongqing Liang,Qiongrong Ou,Shuyu Zhang
Room temperature recrystallization is an intriguing method of fabricating CsPbX3 perovskite quantum dots since it does not involve high temperature or inert atmosphere, offering a promising route to the mass production of CsPbX3 quantum dots at low cost. However, their performance stability during work was seldom investigated and was far from the requirements for practical applications. Here, we demonstrate a facile and low-cost method to significantly improve the thermal, photo- and water stability of room-temperature synthesized perovskite quantum dots by effectively suppressing the unfavored grain growth and surface trap states. The fabricated quantum dots of green-emitting CsPbBr3 and red-emitting CsPbBr1.2I1.8 were applied for quantum dot-converted white LEDs, which are capable of achieving a wide color gamut of 135% NTSC and 101% Rec. 2020.
研究领域:
材料科学
·
显示技术
·
纳米科技
✓ 已验证
产品关联
DOI
高影响因子
NANOTECHNOLOGY
·
2022
·Vol. 33
·期 17
·175603
·
IF 3.953
Chen Chen,Lei Nie,Yizhe Huang,Shuang Xi,Xingyue Liu,Xiwen Zhang,Tielin Shi,Guanglan Liao,Shiyuan Liu,Zirong Tang
Herein, we develop a novel strategy for preparing all-inorganic cesium lead halide (CsPbX3, X = Cl, Br, I) perovskite nanocrystals (NCs)@Zn-based metal-organic framework (MOF) composites through interfacial synthesis. The successful embedding of fluorescent perovskite NCs in Zn-MOFs is due to the in situ confined growth, which is attributed to the re-nucleation of water-triggered phase transformation from Cs4PbBr6 to CsPbBr3. The controllable synthesis of mixed-halide based composites with various emission wavelength can be achieved by adding the desired amount of halide (Cl or I) salts in the re-nucleation process. More importantly, the anion exchange reaction is inhibited among various composites with different halogen atoms by being trapped in MOFs. Besides, a white light-emitting diode (WLED) is produced using a blue LED chip with the green-emitting and red-emitting composites, which has a color coordinate of (0.3291, 0.3272) and a wide color gamut. This work provides a novel route to achieving perovskite NCs growth in MOFs, which also can be extended to the other NCs embedded in frames as well.
研究领域:
材料科学
·
化学
✓ 已验证
产品关联
DOI
PubMed
高影响因子
CERAMICS INTERNATIONAL
·
2022
·
IF 5.532
Hangtao Ye,Luojia Huang,Xiaoting Liu,Meiting Yang,Wenya Chen,Yihuang Chen,Weidong Xiang,Shuang Pan,Xiaojuan Liang
Although backlight display screens based on CdSe quantum dots (QDs) have basically solved the remaining problem of small display gamut, its high preparation cost limits its commercial development. In contrast, perovskite nanocrystals (NCs) with narrow band emission, simple preparation and low cost have made leaps and bounds in next-generation backlit displays luminescent material . However, the instabilities are the main issues to solve before we can apply these materials in modern displays. Researchers have precipitated perovskite NCs in inorganic glass substrates and compounded them with PDMS films for backlighting, but the important factors for commercialization have been ignored: Long-term stability under strong blue light irradiation and preparation cost. In this work, a unique melt-water quenching method combined with composition control was applied to prepare a series of glass powder. The optimal photoluminescence (PL) emission and color coordinates in the color coordinates of glasses powder were elaborately regulated by heat treatment temperature control and the introduction of rare earth Tb. Moreover, the passivation of the glass powder surface through special water treatment greatly improves its stability under long time blue light exposure. After irradiation under 20000 cd/m 2 blue light (460 nm) for 500 h, the PL intensity retention rate reaches 85% of commercial CdSe film. The red and green-emitting NCs glasses powder with high photoluminescence quantum yield (PLQY) and stability were combined with PET, PS and PDMS to form a composite film , afterwards, combined with Liquid crystal display ( LCD ) module shows a fuller color image. Finally, after comparison, PS film was demonstrated to be the most suitable choice for commercialization backlighting.
研究领域:
材料科学
·
光学工程
✓ 已验证
产品关联
DOI
高影响因子
Nanoscale
·
2018
·Vol. 10
·期 22
·10505-10513
·
IF 7.233
Xu Chen,Dongyu Li,Gencai Pan,Donglei Zhou,Wen Xu,Jinyang Zhu,He Wang,Cong Chen,Hongwei Song
CsPbX3 (X = Cl, Br or I) perovskite quantum dots (PQDs) have attracted tremendous attention due to their extraordinarily excellent optical properties. However, there is still an obstacle for their bio-application, which is limited by their water-instability. In this work, we have designed a novel visible light triggered photoelectrochemical (PEC) sensor for dopamine (DA) based on CsPbBr1.5I1.5 PQD immobilized three-dimensional (3D) TiO2 inverse opal photonic crystals (IOPCs). Supported by the TiO2 IOPCs, the water-stability of the PQDs as well as that of the PEC sensor was considerably improved. Furthermore, employed as a photoactive material in PEC sensor, CsPbBr1.5I1.5 PQDs can expand the photocurrent response of the PEC sensor to the whole visible region. In addition, the modulation of the photonic stop band effect of TiO2 IOPCs on the incident light and the emission of PQDs could further enhance the photocurrent response. Such a PEC sensor demonstrates sensitive detection of DA in phosphate buffer saline solution and serum, with a good linear range from 0.1 μM to 250 μM and a low detection limit of approximately 0.012 μM. Our strategy opens an alternative horizon for PQD based PEC sensing, which could be more sensitive, convenient and inexpensive for clinical and biological analysis.
研究领域:
材料科学
·
光化学
·
分析化学
·
生物传感器
✓ 已验证
DOI
高影响因子
Polymers
·
2024
·Vol. 16
·期 11
·1568
·
IF 4.7
Yinbiao Shi,Xiaojia Su,Xiaoyan Wang,Mingye Ding
Inorganic CsPbX3(X = Cl, Br, I) perovskite quantum dots (PQDs) have attracted widespread attention due to their excellent optical properties and extensive application prospects. However, their inherent structural instability significantly hinders their practical application despite their outstanding optical performance. To enhance stability, an in situ electrospinning strategy was used to synthesize CsPbX3/polyacrylonitrile composite nanofibers. By optimizing process parameters (e.g., halide ratio, electrospinning voltage, and heat treatment temperature), all-inorganic CsPbX3PQDs have been successfully grown in a polyacrylonitrile (PAN) matrix. During the electrospinning process, the rapid solidification of electrospun fibers not only effectively constrained the formation of large-sized PQDs but also provided effective physical protection for PQDs, resulting in the improvement in the water stability of PQDs by minimizing external environmental interference. Even after storage in water for over 100 days, the PQDs maintained approximately 93.5% of their photoluminescence intensity. Through the adjustment of halogen elements, the as-obtained composite nanofibers exhibited color-tunable luminescence in the visible light region, and based on this, a series of multicolor anti-counterfeiting patterns were fabricated. Additionally, benefiting from the excellent water stability and optical performance, the CsPbBr3/PAN composite film was combined with red-emitting K2SiF6:Mn4+(KSF) on a blue LED (460 nm), producing a stable and efficient WLED device with a color temperature of around 6000 K and CIE coordinates of (0.318, 0.322). These results provide a general approach to synthesizing PQDs/polymer nanocomposites with excellent water stability and multicolor emission, thereby promoting their practical applications in multifunctional optoelectronic devices and advanced anti-counterfeiting.
研究领域:
材料科学
·
光学工程
·
纳米技术
✓ 已验证
产品关联
DOI
PubMed
高影响因子
危险品化学品经营许可证（带存储）