SEPARATION AND PURIFICATION TECHNOLOGY
·
2024
·
IF 8.1
Feilong Dong,Menglan Duan,Bo Xu,Tian Sun,Kexin Wu,Shan Luo
Aniline, a toxic aromatic amine prevalent in printing and dyeing effluents, has garnered significant attention due to its potential risks to human health and the environment. In this study, 3D blocky melamine sponge-supported spinel ferrite nanocomposites (MFe 2 O 4 @MS) were synthesized to activate peroxymonosulfate (PMS) for the removal of aniline from printing and dyeing wastewater. The CoFe 2 O 4 @MS-PMS achieved complete removal of aniline within 10 min across a pH range of 5 to 11, significantly outperforming the CuFe 2 O 4 @MS-PMS and ZnFe 2 O 4 @MS-PMS systems. Electron paramagnetic resonance (EPR) and probe-based kinetic model experiments certified the formation of sulfate radicals (•SO 4 − ), hydroxyl radicals (•OH), and singlet oxygen ( 1 O 2 ) during the process, where •SO 4 − was identified as the principal reactive species responsible for aniline degradation. The Langmuir-Hinshelwood model demonstrated that the melamine sponge framework significantly improved the dispersion and adsorption capabilities of MFe 2 O 4 nanoparticles. This enhancement led to localized enrichment of aniline and PMS on the surface. Furthermore, the removal of aniline by CoFe 2 O 4 @MS-PMS performed satisfactorily in five-cycle experiments and in actual printing and dyeing wastewater. This research offers new insights into the design and synthesis of environmentally friendly and highly active PMS catalysts for aniline degradation in industrial wastewater.
✓ 已验证
产品关联
DOI
高影响因子
INDUSTRIAL & ENGINEERING CHEMISTRY RESEARCH
·
2024
·
IF 3.8
Jiabao Li,Dongxia Yan,Xiujie Cheng,Chunrui Rong,Jian Feng,Xin Feng,Jiayu Xin,Qing Zhou,Yi Li,Junli Xu,Xingmei Lu
The methanolysis of polyethylene terephthalate (PET) can address the environmental pollution and resource waste caused by waste PET, and the obtained monomer dimethyl terephthalate (DMT) is easy to separate and purify. However, conventional methanolysis of PET usually uses metal-containing catalysts, resulting in metal residues in the degradation products, which affects subsequent high-value utilization. Meantime, the reaction conditions of high temperature and high pressure promotes the occurrence of side reactions and reduces the yield of the main products. Herein, the nonmetallic deep eutectic solvent (DES) 1,5-diazabicyclo [4.3.0]-5-nonene (DBN)/Phenol was employed as a catalyst for PET methanolysis. 100% PET conversion and 95.3% DMT yield were obtained at 130 °C for 1 h. The possible reaction mechanism was investigated by combining NMR, FT-IR, GPC analysis, and DFT calculations. DBN and phenol were connected through N–H–O hydrogen bonding, where the hydrogen atom interacted with the carbonyl oxygen of PET and the oxygen atom activated the hydroxyl group of methanol. Additionally, GPC analysis showed that the dissolution and degradation of PET were simultaneous, which enhanced mass transfer and facilitated the reaction. The kinetic studies showed that PET methanolysis followed the first-order kinetic model with an activation energy of 103.3 kJ/mol, which was lower than the literature-reported value. This research provides an efficient nonmetallic deep eutectic solvent catalyst for PET methanolysis, which solves the problem of metal residues in the degradation products and reduces the reaction temperature. It is of great significance to simplify the purification steps and improve the economy of regeneration.
✓ 已验证
产品关联
DOI
高影响因子
COLLOIDS AND SURFACES A-PHYSICOCHEMICAL AND ENGINEERING ASPECTS
·
2024
·
IF 4.9
Shuyu Chen,Zhengkai Wu,Xueying Cheng,Lu Chen,Yunning Chen,Yingna Guo,Changhua Wang,Qingkun Shang
In this work, we used a simple hydrothermal method to in-situ grow Zn 3 In 2 S 6 on MIL-100(Fe) octahedra, and obtained a MIL-100(Fe)@Zn 3 In 2 S 6 Z-scheme heterojunction photocatalyst. We systematically studied its performance in degrading phenol and p-nitrophenol (PNP) under visible light. MIL-ZIS 6 -2 can remove 89.1 % of phenol within 120 min and nearly 100 % of PNP within 60 min. Its photocatalytic activity to the degradation of phenol is 30.7 times and 1.7 times higher than that of MIL-100(Fe) and Zn 3 In 2 S 6 , respectively. And the photocatalytic activity to degrade PNP is 18.2 times and 1.4 times higher than MIL-100(Fe) and Zn 3 In 2 S 6 . Further research was conducted on its band structure and photocatalytic response mechanism through photoelectric performance, ultraviolet photo-electron spectroscopy, and electron spin resonance spectrometer testing. The results showed that the formation of Z-scheme heterojunction not only increased the specific surface area of the composite photocatalyst, enabling it to provide more reaction sites, but also effectively suppressed the recombination of photogenerated holes and electrons, improving the redox ability of the photocatalyst. This work provides a new perspective for constructing efficient Zn 3 In 2 S 6 -based composite photocatalysts and addressing environmental issues.
✓ 已验证
产品关联
DOI
高影响因子
COLLOIDS AND SURFACES A-PHYSICOCHEMICAL AND ENGINEERING ASPECTS
·
2024
·
IF 4.9
Tian Xiao,Shiwei Xie,Zhi Liu,Chengyi Fang,Yi Li,Hui Hong,Wei Shao,Na Zhang
For the purpose of degrading tetracycline (TC), a three-dimensional electro-oxidation (3D EO) system using particle electrodes of carbon black (CB) and polytetrafluoroethylene (PTFE) was developed. The CB-PTFE particles fabricated at a CB/PTFE mass ratio of 3:2 and calcination time of 60 min exhibited the high performance for TC removal, as well as low energy consumption and high mechanical strength. TC removal efficiency reached 95% within 15 minutes, driven by a pseudo-first-order reaction with a rate constant of 0.20 min −1 . The process incurred an energy consumption of 20.31 kWh/m 3 . The surface characterizations indicated that the CB-PTFE particles possessed excellent catalytic properties for H 2 O 2 production. Despite the substantial influence of voltage and particle dosage on performance, the system demonstrated consistently high efficiency in TC removal regardless of solution pH within the range of 3–11. Quenching experiments and probe experiments using benzoate suggested that the surface-bound hydroxyl radicals (•OH (ads) ) dominated (64.7%) the oxidation of TC in the 3D CB-PTFE EO system. The •OH (ads) was produced by the reduction of H 2 O 2 on the particle surface. Products examination by LC-MS-MS confirmed a degradation pathway of TC by •OH attacking. These findings indicate that the CB-PTFE EO system has unique advantages and potentials in treating antibiotics due to its high oxidizing capacity, a wide range of applicable pH, no chemical adding, and self-cleaning.
✓ 已验证
产品关联
DOI
高影响因子
ACS ES&T Water
·
2025
·
IF 4.3
Shizong Wang,Jianlong Wang
Herein a novel advanced wastewater treatment process based on electron beam radiation-induced polymerization was developed. During the radiation process of phenol-containing wastewater, polymerization products of high molecular weight (MW) were formed, and their distribution could be regulated by the absorbed doses. Chloride and sulfate ions decreased the proportion of ≥5000 Da products and increased the proportion of ≤100 Da. At acidic conditions, the MW distribution was dominated by ≤100 Da, 100–500 Da, and 500–5000 Da; at alkaline conditions, by ≤100 and 100–500 Da; and at neutral conditions, by ≤100 Da, 100–500 Da, 500–5000 Da, and ≥5000 Da. Gel permeation chromatography and Fourier-transform mass spectrometry confirmed the formation of hydrophobic polymers through phenol and its polymerization products, which were induced by HO•. The process was validated in actual coking and dyeing wastewater, where polymerization enhanced the removal efficiency of UF, NF, and RO. This electron beam radiation-induced polymerization could decrease the absorbed dose required for complete degradation of organic pollutants and reduce carbon dioxide emission compared to traditional advanced oxidation processes, offering a promising solution for the treatment of refractory industrial wastewater.
✓ 已验证
产品关联
DOI
高影响因子
MOLECULES
·
2024
·Vol. 29
·期 21
·4994
·
IF 4.2
Fan Ma,Hong-Wei Lin,Zizi Li,Wen-Jing Li,Jia-Wei Wang,Gangfeng Ouyang
Noble-metal-free CO2reduction systems based on cobalt phthalocyanine (CoPc) and its derivatives have demonstrated remarkable photocatalytic performances; however, their structure-activity relationship with electronic tuning remains unexplored. Herein, we now provide a systematic study to investigate the electron effects of substituents on theCoPcfamily in photocatalytic CO2reduction, where a Cu(I) heteroleptic photosensitizer is utilized. The highest performance can be achieved using cobalt tetracarboxylphthalocyanine in light-driven CO2-to-CO reduction, with a maximum turnover number of 2950 at 450 nm and an outstanding apparent quantum yield of 63.5% at 425 nm, over ten times the activity with the tetra-dimethylamino-substitutedCoPcderivative. The favorable electron-withdrawing effects have been further verified by DFT calculations and cyclic voltammetry, which reduces the overpotential required for CO2reduction and decreases the Gibbs free energy of the catalyst active intermediates, particularly the CO-desorption energetics.
✓ 已验证
产品关联
DOI
PubMed
高影响因子
Journal of Water Process Engineering
·
2024
·
IF 6.3
Zhuoyue Liu,Dong Cheng,Haochen Yin,Jianghao Zhao,Jiale Zhang,Rongzhi Chen,Shengjiong Yang,Jing Wei,Gen Wang
Nascent MnO 2 colloids produced during the permanganate oxidation process is highly oxidative and appealing for eliminating emerging organic contaminants (EOCs). However, the nascent MnO 2 colloids usually shows dense bulked structure, which blocks the availability of active sites and further enhancement of the reactivity. Herein, spherical nascent MnO 2 colloids with mesoporous structure were synthesized via redox reactions between colloidal nanospheres of plant polyphenol (e.g., tannic acid) and permanganate. The mesoporous nascent MnO 2 colloids shows highly exposure of active sites with abundant bulk-Mn(III) on the surface (16.2 mol%), and thus exhibits outstanding oxidation performance toward the oxidation of phenolic contaminants. Complete removal of bis-phenol A (BPA, 10 mg/L) was obtained with 1.0 mM of mesoporous nascent MnO 2 colloids in 40 min at neutral pH. Mechanism study reveals that both Mn(III) and Mn(IV) contribute to the oxidation of BPA. The presence of bulk-Mn(III) on the surface greatly promotes the reactivity of the mesoporous nascent MnO 2 colloids, leading to a high kinetic of 0.12 min −1 during the initial 10 min. The nascent mesoporous MnO 2 colloids exhibits high selectivity toward electron rich phenolic contaminants and good performance in complicated water matrix, revealing a promising potential for further application. This work provides a distinct case for engineering novel structured nascent MnO 2 colloids for efficient elimination of EOCs in water.
✓ 已验证
产品关联
DOI
高影响因子
ENVIRONMENTAL POLLUTION
·
2024
·
IF 7.6
Binbin Shao,Chenkai Hu,Hainan Zhao,Chengcheng Xiao,Erdeng Du,Anhong Cai,Jing Deng
Ambroxol (AMB) is a commonly used bromine-containing organic compound in medical applications and has been frequently found in water environments, which might pose risks of forming brominated disinfection by-products (Br-DBPs) in water treatment systems. The degradation kinetics as well as the degradation mechanism of AMB in the UV/chloramine process were investigated in this study. It was determined that reactive chlorine species (RCS) and the reactive nitrogen species (RNS) were the dominant free radicals for AMB degradation. Debromination occurred mainly in the initial stage of the degradation process, with a debromination rate of 34.5% at 10 min. Four possible degradation pathways of AMB were proposed based on liquid chromatography mass spectrometry (LC-MS) analysis as well as density functional theory (DFT) calculations, meanwhile the ECOSAR model was used to predict the toxicity risk of AMB and its degradation intermediates. Furthermore, after assessing the formation of DBPs during the UV/chloramine pre-oxidation process and conducting a toxicity risk analysis based on the results, it has been verified that this method can effectively remove AMB while reducing the formation potential of DBPs in the water environment. This suggests that the UV/chloramine process shows promise for treating bromine-containing organic compounds in real-world water treatment applications.
✓ 已验证
产品关联
DOI
PubMed
高影响因子
Toxics
·
2024
·Vol. 12
·期 10
·746
·
IF 3.9
Han Zhang,Jinping Duan,Pengcheng Luo,Luxiang Zhu,Yanan Liu
The widespread occurrence of atrazine (ATZ) in water environments presents a considerable risk to human health and ecosystems. Herein, the performance of dielectric barrier discharge integrated with periodate (DBD/PI) for ATZ decomposition was evaluated. Results demonstrated that the DBD/PI system improved ATZ decomposition efficiency by 18.2–22.5% compared to the sole DBD system. After 10 min treatment, the decomposition efficiency attained 82.4% at a discharge power of 68 W, a PI dosage of 0.02 mM, and an initial ATZ concentration of 10 mg/L. As the PI dosage increased, the decomposition efficiency exhibited a trend of initially increasing, followed by a decrease. Acidic conditions were more favorable for ATZ removal compared to alkaline and neutral conditions. Electron paramagnetic resonance (EPR) was adopted for characterizing the active species produced in the DBD/PI system, and quenching experiments revealed their influence on ATZ decomposition following a sequence of1O2> O2−• > IO3• > OH•. The decomposition pathways were proposed based on the theoretical calculations and intermediate identification. Additionally, the toxic effects of ATZ and its intermediates were assessed. This study demonstrates that the DBD/PI treatment represents an effective strategy for the decomposition of ATZ in aquatic environments.
✓ 已验证
产品关联
DOI
PubMed
高影响因子
Nanomaterials
·
2025
·Vol. 15
·期 6
·432
·
IF 4.3
Xin Zhong,Xiaojun Liu,Meihuan Ji,Fubin Jiang
As the most promising techniques for refractory antibiotic degradation in wastewater management, sulfate radical-based advanced oxidation processes (SR-AOPs) have attracted considerable attention. However, systematic studies on potassium peroxymonosulfate (PMS) activation by MOF-derived metal oxides coated with LDH materials are still lacking. In this work, a series of catalysts consisting of CoCu-MOFs coated with CuAl/LDH were synthesized for PMS activation in the removal of sulfamethoxazole (SMX). As expected, CoCu-MOFs coated with CuAl/LDH catalyst showed high SMX removal and stability in PMS activation. In the CoCu/LDH/PMS reaction, the SMX removal was nearly 100% after 60 min, and the mineralization reached 53.7%. The catalyst showed excellent catalytic stability and low metal leaching concentrations (Co: 0.013 mg/L, Cu: 0.313 mg/L), as detected by ICP. Sulfate radicals and hydroxyl radicals were identified as the dominant reactive species in the CoCu/LDH/PMS system. Moreover, the presence of 1 O 2 in the process revealed the coupling of non-radical and radical processes. The XPS results showed that the layered structure of CoCu/LDH promoted the recycling of metal ions (high and low valence), which facilitated heterogeneous PMS activation. The effects of different reaction conditions and reuse cycles were also determined. The SMX oxidation pathways were proposed based on the intermediates identified by LC/MS. The high activity and stability of CoCu/LDH provide a new mechanistic understanding of PMS activation catalysts and their potential utilization in practical wastewater treatment.
✓ 已验证
产品关联
DOI
PubMed
高影响因子
JOURNAL OF THE ENERGY INSTITUTE
·
2024
·
IF 5.6
Bo Chen,Qing-Pan Du,Zhi-Jun Diao,Hong Yuan,Jia-Meng He,Yi-Qing Xie,Xiao-Ran Wang,Yu Wang
Hydrogenation upgrading is an effective technique that lowers the oxygen content of bio-oil with the aim of improving its quality. In order to fabricate a series of Ru-based catalysts for the hydrodeoxygenation of bio-oil, several all-silica supports with different pore sizes are synthesized and modified with Al and Cs in this work. The physical morphology and electronic structure of the catalysts are characterized using multiple techniques including X-ray diffraction, in-situ pyridine adsorption infrared spectroscopy, in-situ diffuse reflectance Fourier transform infrared spectroscopy , Raman spectroscopy , CO 2 temperature-programmed desorption, scanning electron microscopy, energy-dispersive X-ray spectroscopy, transmission electron microscopy , X-ray photoelectron spectroscopy and N 2 physical adsorption-desorption testing. Phenol , guaiacol , anisole and o-cresol are selected as model compounds to investigate the hydrodeoxygenation reactivity of the catalysts. The results reveal that there is a strong linear correlation between the pore size of the catalysts and the rates of the hydrogenation and hydrodeoxygenation of phenol. Importantly, both the oxygen vacancy density and relative content of Brønsted and Lewis sites (B/L) of the catalysts can be greatly increased by Cs modification, which further linearly promotes the hydrodeoxygenation activity of the catalysts. In addition, the in-situ infrared spectroscopy results show that the catalysts modified by Al and Cs heterolytically cleave H 2 to supply H + for the reaction. This work presents a novel approach for fabricating catalysts employed in the hydrotreatment process of bio-oil.
✓ 已验证
产品关联
DOI
高影响因子
JOURNAL OF ALLOYS AND COMPOUNDS
·
2024
·
IF 5.8
Liwei Liang,Songlin Cai,Lan Zhang,Ke Sun,Ziying He,Libin Zhang,Ciyuan Huang,Min Long,Hongxiang Zhu,Bingsuo Zou,Tao Liu,Shuangfei Wang
Phenol has various applications in industry, due to its hazardousness, solubility, and volatility, it persists in water and poses a risk to human health. People are excited by the progress of photodegradation technology that facilitates water pollution treatment. The effect of side-chain engineering is proven to enhance photodegradation performance by improving optoelectronic properties. Therefore, here is a strategy that introduces functional groups to change the electron cloud density, achieving excellent optoelectronic properties evidenced by efficient exciton dissociation, separation, and fine-tuned energy level. Subsequently, by coupling of photocatalysis and adsorption, the donor/acceptor (D/A) heterojunction photocatalysts (PBDB-T: BTTIC-TT, PBDB-T: BTTIC-Ph) are designed via loading on coconut-shell carbon to process phenol. The results indicate that the champion photocatalyst PBDB-T: BTTIC-TT possesses superior optoelectronic properties, which can be attributed to the stronger electron-withdrawing ability of thieno[3,2- b ]thiophene than benzene. Consequently, the synergistic efficiency of adsorption and photocatalysis of phenol (10, 20 mg/L) are removed within 10 mins over 90 % which is still valid after twenty cycles. Surprisingly, a high concentration of phenol (100 mg/L) also exhibited excellent removal efficiency of over 80 % within 60 min.
✓ 已验证
产品关联
DOI
高影响因子