文献检索

查找使用阿拉丁产品的科研文献

检索与阿拉丁产品相关的同行评审论文、DOI、PubMed 编号、期刊、作者、CAS 号及研究领域。

科研影响力快照

与阿拉丁产品相关的已发表科研成果

在搜索之前,这些指标可帮助访客快速了解产品关联科研的规模与质量。

347,389+ SCI 论文 与阿拉丁产品引用相关
2,303,681.05 总影响因子 匹配文献记录中影响因子的总和
81.20 最高期刊影响因子 匹配期刊中的最高 IF
6.63 平均期刊影响因子 匹配文献的平均 IF

参考指标 指标基于阿拉丁文献引用数据库及期刊影响因子记录。文献关联仅供科研参考,请以原始文献为准。

产品列表

视图 列表 网格

显示第1105至1116个,产品总数347,389个

切换升序
ELECTROCHIMICA ACTA · 2026 · IF 5.8

Dynamic suppression of interfacial alkalization for reversible zinc plating and stripping in aqueous zinc batteries

Xinchun Song,Yuhang Zhang,Gan Li,En Gao,Yongtao Li,Zhipeng Jiang

● TMSOTf regulates interfacial alkalization during zinc plating/stripping. ● HOTf neutralizes OH − and limits zinc hydroxy sulfate formation. ● TMSOH-derived Si–O species form a hydrophobic zinc interface. ● The modified interface reduces hydrogen evolution and zinc corrosion. Aqueous zinc batteries (AZBs) are promising candidates for large-scale energy storage, but the limited reversibility of zinc metal anodes (ZMAs) remains a major challenge. In aqueous electrolytes, hydrogen evolution reactions (HER) continuously generate OH – at the Zn/electrolyte interface, leading to local alkalization, zinc hydroxy sulfate by-products, surface passivation, and nonuniform Zn deposition. Although electrolyte additives have been widely used to stabilize Zn anodes, many existing strategies mainly rely on solvation-structure regulation or static interphase formation and do not directly address the dynamic accumulation of alkaline species during cycling. Herein, trimethylsilyl trifluoromethanesulfonate (TMSOTf) is introduced as an interfacial alkalization-regulating additive for aqueous Zn electrolytes. In the electrolyte, TMSOTf undergoes hydrolysis to generate trifluoromethanesulfonic acid (HOTf) and trimethylsilanol (TMSOH). The generated HOTf neutralizes HER-induced OH – and suppresses the accumulation of Zn 4 SO 4 (OH) 6 ·xH 2 O by-products, thereby mitigating interfacial passivation. Meanwhile, TMSOH-derived Si-O-containing species contribute to the formation of a hydrophobic interfacial layer that reduces direct water access to Zn and suppresses water-induced parasitic reactions. Electrochemical analyses further show that TMSOTf decreases corrosion, regulates Zn nucleation behavior, and promotes more uniform Zn plating/stripping. As a result, the electrolyte containing 1 vol% TMSOTf enables Zn-Zn symmetric cells to cycle for more than 2500 h and Zn-Cu half-cells to operate for more than 5000 cycles at 5 mA cm –2 and 1 mAh cm –2 . Under practical conditions, a Zn-NH 4 V 4 O 10 full cell with a 10 μm Zn foil anode, a cathode loading of 3.1 mg cm –2 , and an N/P ratio of 4.8 retains 72.2% of its capacity after 100 cycles at 1 A g –1 . In addition, a 0.5 Ah Zn-NaV 3 O 8 pouch cell with a cathode loading of 16.6 mg cm –2 operates for 50 cycles with 73.2% capacity retention. This work establishes dynamic interfacial alkalization regulation as an electrochemical strategy for stabilizing Zn metal anodes in aqueous electrolytes. Download: Download high-res image (263KB) Download: Download full-size image

CAS / MDL: 7446-20-0
✓ 已验证 产品关联 DOI 高影响因子
查看原文 查看 PubMed
JOURNAL OF COLLOID AND INTERFACE SCIENCE · 2026 · IF 9.6

High-entropy metal-organic framework@MXene heterostructure-modified separator promotes polysulfide immobilization and conversion for high-performance lithium-sulfur batteries

Jinze Song,Lixia Zhu,Ying Song,Zhaobo Wang,Kaixiang Shi,Xiaolei Song,Quanbing Liu,Guangfeng Wu

HE-MOF@MXene heterostructure was constructed via in situ growth. • The heterostructure combines physical blocking with chemical LiPSs anchoring. • Multi-metal synergy accelerates catalytic conversion of LiPSs. • HE-MOF@MXene//PP delivers 1445 mAh g −1 at 0.2C and 690 mAh g −1 at 5C. • HE-MOF@MXene//PP shows only 0.059% decay per cycle over 900 cycles at 1C. Lithium‑sulfur batteries (LSBs) offer high energy density, yet their performance is restricted by uncontrolled lithium polysulfides (LiPSs) migration and the intrinsically slow multistep conversion of sulfur species. To alleviate these issues, a Fe/Co/Ni/Cu/Mn high-entropy metal-organic framework (HE-MOF) was directly grown on MXene nanosheets to form an HE-MOF@MXene heterostructure, which was subsequently employed as a separator modifier in LSBs. The reciprocal structural regulation between HE-MOF and MXene effectively suppresses component aggregation and layer re-stacking, thereby increasing the accessible surface area of the heterostructure and promoting greater active-site exposure. Meanwhile, the two components are functionally integrated. The well-exposed high-entropy multimetal sites in HE-MOF can effectively exert their adsorption and catalytic advantages toward sulfur species with the assistance of the efficient electron/ion transport network constructed by MXene. Density functional theory calculations suggest distinct electronic structures and d-d interactions among the metal sites in HE-MOF. The resulting multimetal synergy may help accommodate the differentiated adsorption requirements of sulfur species and facilitate their subsequent conversion. Consequently, with the separator functionalized by HE-MOF@MXene, the cell achieves 1445 mAh g −1 at 0.2C. At a high rate of 5C, the cell still delivers 690 mAh g −1 . Moreover, continuous operation over 1000 cycles at 3C results in an average capacity loss of merely 0.060% per cycle. HE-MOF@MXene heterostructure-modified separators integrate efficient physical blocking, strong polysulfide anchoring and rapid sulfur redox reaction kinetics, effectively suppressing shuttle effects and enabling high-performance lithium-sulfur batteries. Download: Download high-res image (239KB) Download: Download full-size image

CAS / MDL: 7447-41-8 7704-34-9
✓ 已验证 产品关联 DOI PubMed 高影响因子
查看原文 查看 PubMed
Catalysts · 2026 ·Vol. 16 ·期 8 ·673 · IF 4.5

Fe/S-Modified MIL-125 for Efficient Photocatalytic Degradation of Antibiotics: Performance and Mechanism

Shuai Wang,Peiyao Chen,Huanhuan Li,Yingning Wang,Xiongwei Liang,Changhao Yao,Yang Yang

Antibiotics have been extensively used in medicine and aquaculture, leading to severe environmental contamination. Among them, chlortetracycline (CTC) has attracted considerable attention due to its large consumption and high residual risk. MIL-125(Ti), as a representative titanium-based metal–organic framework, exhibits good structural stability and tunability; however, its intrinsically weak visible-light response and rapid charge recombination limit further photocatalytic applications. To improve its photocatalytic performance, MIL-125 was first synthesized via a hydrothermal method, and then Fe and S species were introduced through a combination of in situ coprecipitation and mild sulfuration, yielding an Fe/S-modified MIL-125 photocatalyst. The introduction of Na2S induced defect sites and coordinatively unsaturated centers on the MIL-125 surface, while the cooperative participation of Fe species further regulated the surface electronic structure and active-site distribution, thereby enhancing visible-light absorption and interfacial charge transfer. Under AM 1.5 irradiation, the optimized Fe/S-MIL-125 achieved a CTC degradation efficiency of 98.6% within 120 min at an initial concentration of 40 mg L−1. In addition, the material exhibited broad applicability toward multiple antibiotics, with degradation efficiencies exceeding 87% for ciprofloxacin (CIP) and clindamycin (CLI). Cycling tests demonstrated that the catalyst retained high activity after five successive runs, indicating excellent stability. Radical scavenging experiments and ESR analyses revealed that superoxide radicals (·O2−) were the dominant reactive species. Overall, the Fe/S-modified strategy significantly enhanced the photocatalytic performance of MIL-125 through defect engineering and interfacial charge regulation, offering a promising approach for the design of MOF-based materials for antibiotic removal.

✓ 已验证 产品关联 DOI 高影响因子
查看原文 查看 PubMed
JOURNAL OF ALLOYS AND COMPOUNDS · 2026 · IF 6.7

Synergistic enhancement of piezoelectric performance and strain temperature stability in Ce-doped PMN-PT relaxor ferroelectrics

Jiaxuan Cui,Xi Feng,Peng Peng,Tao Chen,Taiyu Zhou,Tianming Li,Li Zhang,An Xue,Zhanming Dou,Fangping Wang,Guifen Fan,Fangfang Zeng

To address the demand for high-precision piezoelectric devices featuring high piezoelectric performance and excellent temperature stability, x Ce-PMN-35PT piezoelectric ceramics were synthesized via cerium doping. Ce ions preferentially occupy the A-site substituting for Pb 2 + , as evidenced by XRD peak shifts and Raman spectral evolution. Combined lattice variation and ionic radius data suggest a valence evolution from Ce 4+ towards Ce 3+ with increasing doping content. The results show that the ceramic with 2 mol% Ce doping exhibits superior comprehensive performance: the piezoelectric coefficient d 33 reaches 780 pC/N, the large-signal piezoelectric coefficient d 33 * is 1101 pm/V, and the unipolar electrostrain only degrades by 6.4% across the broad temperature range from 25 to 125 ℃. Through in situ XRD and Rietveld refinement, this study further elucidated the intrinsic correlation among phase structure, domain switching dynamics, and piezoelectric properties, thereby revealing the underlying mechanism by which cerium doping optimizes material performance. This work not only offers a promising material system for medium-temperature high-precision piezoelectric actuators but also presents an effective strategy for tailoring the properties of PMN-PT-based ceramics.

✓ 已验证 产品关联 DOI 高影响因子
查看原文 查看 PubMed
POLYMERS FOR ADVANCED TECHNOLOGIES · 2026 ·Vol. 37 ·期 7 ·e70693 · IF 3.8

Interfacial Bridging via IPDI-Modified Boron Carbide for Polyurea Coatings With Superior Mechanical and Anti-Corrosion Performance

Hanxin Zhang

Polyurea (PUA) elastomers are highly promising as protective coatings due to their exceptional energy dissipation against dynamic impact. However, conventional PUA suffers from low structural rigidity, and introducing rigid nanofillers often causes severe agglomeration and weak interfacial bonding, thereby hindering the simultaneous improvement of strength and toughness. To address these challenges, an interfacial covalent bridging strategy is developed to prepare isophorone diisocyanate (IPDI)-modified boron carbide (m-B 4 C) reinforced polyaspartic ester polyurea (PAE) coatings. Integrating IPDI-assisted mechanical exfoliation with in situ polymerization ensures uniform dispersion and robust filler-matrix covalent bonding. Nanocomposite coatings with 0.2, 0.5, and 1.0 wt% B 4 C or m-B 4 C were prepared; the optimized 0.5 wt% m-B 4 C coating exhibits 27.8 MPa tensile strength, 350% elongation at break, and 37 kN/m tear strength. Notably, the impact strengths of coated aluminum alloy and epoxy substrates reach 461 and 64 kJ/m 2 , successfully overcoming the stiffness-ductility trade-off. Furthermore, the coatings demonstrate exceptional anti-corrosion capabilities, maintaining a high impedance modulus (6.3 × 10 6 Ω cm 2 ) after 14 days in NaCl solution and remarkable rust resistance during 100 h of salt spray testing. These findings elucidate the synergistic energy dissipation and physical barrier mechanism of the rigid-particle/flexible-matrix architecture, providing a pathway toward designing high-performance multifunctional lightweight protective coatings.

CAS / MDL: 127-19-5
✓ 已验证 产品关联 DOI 高影响因子
查看原文 查看 PubMed
CERAMICS INTERNATIONAL · 2026 · IF 6

Electrospun porous Al18B4O33/h-BN composite fibers with tailored microstructures for high-temperature thermal insulation

Peng Chu,Lindong Ma,Hongli Liu,Zongwei Zhang,Yuhao Liu,Weiqiang Xie,Wenshuo Cao,Mingwei Li,Yuanhang Zhou

Aluminum borate fibers are promising candidates for high-temperature thermal insulation owing to their excellent thermal stability, good chemical resistance, and relatively low density. Herein, we report a simple method for preparing porous Al 18 B 4 O 33 /h-BN composite fibers via electrospinning and stepwise heat treatment, using an aluminum isopropoxide/aluminum nitrate (AIP-AN) complex as the aluminum source and nanoscale h-BN as the boron source. The incorporation of h-BN not only promotes the in-situ formation of the Al 18 B 4 O 33 phase but also affects the fiber's pore structure. Meanwhile, the heterogeneous interface formed between h-BN and the Al 18 B 4 O 33 may introduce additional interfacial thermal resistance, thereby synergistically reducing thermal conductivity and improving thermal insulation performance. The resulting composite fibers exhibited a highly porous structure, with a high specific surface area of 53.9175 m 2  g −1 , a low density of 0.025 g cm −3 , and a low thermal conductivity of 0.0417 W m −1  K −1 . The porous Al 18 B 4 O 33 /h-BN composite fibers demonstrate significant potential for thermal insulation in extreme environments, offering a viable approach to developing high-performance ceramic fiber insulation materials.

CAS / MDL: 555-31-7
✓ 已验证 产品关联 DOI 高影响因子
查看原文 查看 PubMed
Journal of Functional Biomaterials · 2026 ·Vol. 17 ·期 8 ·366 · IF 5.9

Fibrinogen Adsorption and Sponge-like Aggregate Formation on Titanium Modified by Electrochemically Deposited CaCO3

Zubair Ahmed,Huiliang Cao

Fibrinogen adsorption governs biological responses to implantable medical devices; however, surface properties influence the overall functionality of the biomaterial, and guided fibrinogen adsorption remains limited. In the present work, CaCO3was electrochemically deposited on commercial Ti at −1.6 V for 1 h, 2 h, and 3 h. Furthermore, the effects on fibrinogen adsorption were detailed by using dye-assisted scanning electron microscopy (d-SEM), X-ray photoelectron spectroscopy (XPS), and Fourier Transform Infrared Spectroscopy (ATR-FTIR). Longer deposition times produced thicker calcite layers with maximum surface coverage of 99.80 ± 0.40%, accompanied by progressively greater calcium-ion release, ranging from 3.5 mg·L−1·cm−2(1 h) to 12.2 mg·L−1·cm−2(3 h) over 240 min. The results show that electrochemically deposited calcite crystals for 3 h lead to the formation of sponge-like fibrinogen aggregates via calcium ion-mediated conformational activation, particularly by chelating with the histidine and carboxylate residues of the Bβ chain segment Gly-His-Arg-Pro (β15–β18). This structural reorganization was supported by XPS N 1s binding energy at 398.80 eV and a red shift in Amide I and Amide II bands in FTIR spectra. Overall, this study reveals that careful modification of surface chemistry can guide fibrinogen adsorption, which can be beneficial for advanced biomaterials to orchestrate tissue integration at the protein and cellular levels.

✓ 已验证 DOI 高影响因子
查看原文 查看 PubMed
MICROCHEMICAL JOURNAL · 2026 · IF 5.2

Aptamer-gated self-feedback CHA/DNAzyme molecular circuit for enzyme-free ultrasensitive fluorescent sensing of P-tau231

Fang Yang,Tingting Gong,Xia Li,Bingying Jiang,Ruo Yuan,Yun Xiang

A highly sensitive fluorescent biosensor for P-tau231 detection is developed. • Aptamer-gated self-feedback CHA/DNAzyme circuit enables drastic amplification. • 0.45 pg mL −1 detection limit with high specificity against interferents is achieved. • The detection of trace P-tau231in diluted human serums is validated. Phosphorylated tau at threonine 231 (P-tau231) is a clinically informative blood-based biomarker for early Alzheimer's disease (AD), yet its extremely low abundance demands robust signal amplification for sensitive detection of P-tau231. Here, we develop an enzyme-free, target-activated fluorescence assay based on a continuous self-feedback DNA molecular circuit that integrates aptamer recognition, catalytic hairpin assembly, and a Mg 2+ -assisted DNAzyme. P-tau231 binding to an aptamer/ssDNA duplex releases a trigger strand that unlocks a DNAzyme-containing hairpin, initiating an autocatalytic amplification cascade. The activated DNAzyme repeatedly cleaves a fluorophore/quencher-labeled substrate hairpin, converting molecular recognition into a turn-on fluorescence output with substantial signal gain. Under optimized conditions, the proposed strategy enables highly sensitive P-tau231 assay (0.45 pg mL −1 detection limit), while maintaining high specificity against potential interferents. Feasibility in complex matrices is further supported by analysis in diluted human serum. This self-feedback CHA-DNAzyme circuit provides a modular framework for ultrasensitive fluorescence biosensing of low-abundance protein biomarkers relevant to early AD screening. Download: Download high-res image (73KB) Download: Download full-size image

CAS / MDL: 7365-45-9
✓ 已验证 产品关联 DOI 高影响因子
查看原文 查看 PubMed
Catalysts · 2026 ·Vol. 16 ·期 8 ·687 · IF 4.5

Rapid and Efficient Removal of Rhodamine B by a Novel Nickel Oxide/Attapulgite Fenton-like Catalyst: Improved Adsorption and Fenton-like Oxidation

Sadiq Ali,Saeed Ahmed,Huiyu Li,Yongjun Feng

A nickel oxide/attapulgite (A-ATP/NiO) nanocomposite was synthesized and evaluated for the adsorption and Fenton-like degradation of Rhodamine B (Rh-B) in an aqueous solution. The composite was characterized using X-ray diffraction (XRD), Fourier transform infrared spectroscopy (FTIR), scanning electron microscopy (SEM), energy dispersive X-ray spectroscopy (EDS), and Brunauer-Emmett-Teller (BET), confirming the successful immobilization of NiO nanoparticles into the attapulgite framework. The attapulgite modification results in enhanced surface properties, including increased surface area (from 68.9 to 111.3 m2g−1), pore volume, and the availability of active sites. Batch experiments demonstrated a high affinity of A-ATP/NiO toward Rh-B, achieving 52% adsorption within 60 min. Upon addition of Fenton reagent (H2O2), the composite exhibited excellent catalytic performance, achieving 97% Rh-B degradation in 10 min and almost complete removal (99.39%) within 60 min under optimized conditions (pH 3, 303 K, H2O25 mmol L−1, catalyst dose 0.03 g L−1, dye concentration 50 ppm). The synergistic combination of adsorption and catalytic oxidation significantly enhanced dye removal, with reactive hydroxyl radicals (•OH) driving the degradation process. Kinetic analysis indicated that the removal followed a pseudo-first-order model, suggesting that physisorption and surface diffusion are the primary mechanisms for Rh-B degradation. These findings highlight A-ATP/NiO as a low-cost, environmentally friendly, and highly efficient material for the rapid and sustainable remediation of Rh-B-contaminated wastewater.

CAS / MDL: 13478-00-7
✓ 已验证 产品关联 DOI 高影响因子
查看原文 查看 PubMed
INTERNATIONAL JOURNAL OF BIOLOGICAL MACROMOLECULES · 2026 · IF 8.7

Interfacial engineering of a chitosan-tannic acid layer on bacterial cellulose for a high performance forward osmosis membrane toward sustainable juice concentration and reduced microplastic release

Ruiyang Gao,Shanshan Jiang,Shanshan Gao,Haiming Chen,Wenxue Chen,Weijun Chen,Qiuping Zhong,Ming Zhang,Ying Lyu,Rongrong He,Zhenyu Li,Jianfei Pei

Novel forward osmosis membrane based on BC and chitosan-tannic acid interlayers. • BC-CS/TA 3 -PA membrane exhibited superior separation and anti-fouling properties. • Less microplastic leaching was observed with the BC-CS/TA 3 -PA FO membrane. • BC-CS/TA 3 -PA membrane achieves high-efficiency juice concentration. Bacterial cellulose (BC), a renewable biopolymer, has emerged as a promising substrate for membrane fabrication due to its biocompatibility and sustainability. However, the intrinsic heterogeneity in BC fiber distribution results in polydisperse inter-fiber voids, impeding its widespread application in membrane technologies. To mitigate the inherent surface roughness and microporosity of BC substrates, a chitosan-tannic acid interlayer with tunable hydrophilicity was engineered. This interfacial modification facilitated the subsequent formation of an ultrathin, highly cross-linked polyamide selective layer, minimizing defect density in the forward osmosis (FO) membrane. The fabricated FO membrane exhibited a sustained permeate flux (9.07 L·m −2 ·h −1 ) and superior draw solute rejection (>94%), alongside strong anti-fouling durability against bovine serum albumin (BSA) and sodium alginate (SA). Moreover, it demonstrated enhanced chemical stability under acidic and alkaline cleaning regimens. Quantitative assessment via Nile red fluorescence revealed a 63% reduction in microplastic release compared to conventional membranes. Particularly in the application to apple juice concentration, the BC-CS/TA 3 -PA FO membrane increased the contents of total phenols, total flavonoids, and vitamin C by factors of 5.81, 4.14, and 2.46, respectively, compared with thermal concentration, while effectively retaining antioxidant activity in the concentrate. This work provides a foundational framework for fabricating BC-based FO membranes, introduces an innovative approach to eco-friendly, sustainable membrane development, and demonstrates the high feasibility and industrial potential of this novel membrane for apple juice concentration.

✓ 已验证 产品关联 DOI PubMed 高影响因子
查看原文 查看 PubMed
Coatings · 2026 ·Vol. 16 ·期 8 ·907 · IF 3.4

Weavable and Robust Covalent Organic Framework Composite Yarns via Conjugated Electrospinning for Enhanced Dye Adsorption

Yuanyuan Shang,Jie Zhao,Yuanyuan Chen,Wenjing Dou,Yaqing Wang,Yuanyuan Wu,Fei Gao,Juanjuan Li,Baohui Shi

Covalent Organic Frameworks (COFs) are renowned for their high crystallinity and tailored porosity, yet their intractable powder form and poor processability severely limit practical deployment. While electrospun nanofiber membranes offer a pathway to macro-scale COF composites, they often suffer from isotropic mechanical weakness and lack textile processability. Herein, we report a conjugated electrospinning strategy integrated with in situ solvothermal synthesis to fabricate continuous, weavable, and mechanically robust Polyacrylonitrile@Covalent Organic Framework-H (PAN@COF-H) composite yarns. The resulting yarns feature a unique hierarchical architecture where COF-H crystals uniformly coat the surface of oriented nanofibers. This design endows the material with a high specific surface area (94.9 m2/g) and exceptional tensile strength (10 MPa), representing a significant improvement over conventional random electrospun mats. Benefiting from the intrinsic porosity of COF-H and the hydrophilic nature of the composite, the yarns achieve a 73.76% removal rate for Rhodamine B (RhB) within 4 h. Crucially, the material retains over 33.36% of its adsorption capacity after five consecutive cycles, demonstrating outstanding durability. This study bridges the gap between microscopic COF crystals and macroscopic textile architectures, offering a versatile platform for deployable environmental remediation technologies.

CAS / MDL: 34374-88-4
✓ 已验证 产品关联 DOI 高影响因子
查看原文 查看 PubMed
CHEMICAL ENGINEERING JOURNAL · 2026 · IF 12.5

Dual ions-mediated electrochemical polarization enables dynamic electromagnetic wave response in flexible device

Yongbo Yu,Qian Fei,Kailing Zhou,Jingbing Liu,Ziwei Ma,Hao Wang,Hui Yan

A dual-ion (H + /Cl − ) electrochemical polarization strategy dynamically tunes EMW shielding in flexible CNTs@PANI composites. • Dual-ion intercalation restructures PANI to optimize its band gap, sheet resistance, and reflective EMW shielding. • Uneven ion accumulation enlarges dipole moment and dielectric constant, significantly boosting EMW absorption shielding efficiency. • Synergistic reflection-absorption modulation achieves an ultrahigh specific shielding effectiveness variation of 289.44 dB·mm −1 . • A flexible sandwich device offers tunable X-band EMW shielding (26.29–42.06 dB) and robust bending/cycling stability. Dynamic manipulation of electromagnetic waves (EMWs) represents an indispensable cornerstone for next-generation intelligent stealth and adaptive communication systems. Nevertheless, the practical implementation of state-of-the-art electromagnetic materials remains severely constrained by insufficient modulation capabilities arising from single regulatory mechanisms, along with compromised operational flexibility and reliability. Herein, we report a dual-ion-mediated electrochemical polarization strategy in a flexible carbon nanotube@polyaniline (CNTs@PANI)-based device, which enables precise dynamic regulation of EMWs via the synergistic modulation of electromagnetic reflection and absorption. In-situ structural characterizations coupled with theoretical simulations demonstrate that electric-field-triggered H + /Cl − dual-ion intercalation drives the structural rearrangement of PANI from a non-polarized quinoid state to a polarized benzenoid structure. This transformation increases the content of protonated imine groups from 33.01% to 60.97%, narrows the band gap from 2.62 eV to 0.99 eV, and lowers the sheet resistance by 82.4% (from 47.99 to 8.43 Ω·sq. −1 ), thereby tailoring the EMW reflection shielding effectiveness (SE R ) from 4.71 dB to 8.84 dB. Furthermore, the asymmetric electrostatic potential distribution induced by H + /Cl − dual-ion intercalation and accumulation in PANI backbone amplifies the dipole moment by 118% (from 4.02 to 8.77 Debye), generating a pronounced dielectric polarization effect accompanied by maximum enhancement ratios of 172% and 6300% for the real (ε’) and imaginary (ε”) parts of the permittivity, respectively, which boosts the absorption shielding effectiveness (SE A ) from 11.12 to 17.75 dB. Consequently, the synergistic modulation of reflection and absorption contributes to thickness-normalized specific shielding effectiveness variation amplitude (ΔSSE) of 289.44 dB·mm −1 for the CNTs@PANI within the X-band (8.2–12.4 GHz), surpassing previously reported systems. This work establishes a novel paradigm for designing high-performance adaptive EMW protection systems through dual-ion electrochemical engineering.

✓ 已验证 产品关联 DOI 高影响因子
查看原文 查看 PubMed
已复制

文献关联基于可获得的产品、CAS、DOI 及引用记录。收录不代表作者或出版方对阿拉丁产品的背书,请以原始文献为准。