JOURNAL OF APPLIED POLYMER SCIENCE
·
2013
·Vol. 131
·期 8
·
IF 1.395
Caina Min,Qun Pu,Liu Yang,Hong Fan
A novel polysiloxane bearing dodecyl and epoxy side groups (DESO) was synthesized as an intermediate through hydrosilylation of polymethylhydrosiloxane with allyl glycidyl ether and 1-dodecene. Then, dodecyl/piperazine functional polysiloxane (DPSO) was prepared through the reaction of N -aminoethylpiperazine with DESO. The chemical structure of DPSO was characterized with FTIR and 1 H-NMR spectroscopy and its application performance on cotton fabrics was studied. DPSO with dodecyl side groups gifted the treated fabrics with good wettability and whiteness compared with piperazine functional polysiloxane, while with a slightly reduced softness as well as thickening handle. Film morphology, orientation, and performance on cotton substrates of DPSO were investigated by scanning electron microscope, atomic force microscopy, X-ray photoelectron microscope, and so on. Affected by the dodecyl side groups, DPSO formed relatively hydrophilic, macroscopically smooth but actually uneven films with many dodecyl side chain pillars on the treated substrate surfaces. © 2013 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2014 , 131 , 40186.
研究领域:
高分子化学
·
纺织化学与染整工程
·
材料表面科学
·
功能材料
✓ 已验证
DOI
高影响因子
RSC Advances
·
2012
·Vol. 2
·期 12
·5403-5410
·
IF 0
Qinghua Liang,Yao Shi,Wangjing Ma,Zhi Li,Xinmin Yang
Uniform square-like BaFBr:Eu2+ microplates were successfully fabricated via a simple water/oil emulsion method. Various characterization techniques such as X-ray diffraction (XRD), Fourier transform infrared spectroscopy (FT-IR), Raman spectroscopy, Scanning electron microscopy (SEM) and Transition electron microscopy (TEM) were employed to examine the phase, size, morphology, and structure of the products. It was found that the morphology and size of products were strongly dependent on the reaction parameters, such as the ratio of reactants, the reaction time and the reaction temperature. The length and thickness of these square-like BaFBr:Eu2+ microplates can be tuned by adjusting the reaction time and temperature. Well-dispersed cuboctahedron and corner cut cuboid-like BaFBr:Eu2+ particles were produced when the reaction temperature was increased above 60 °C. A possible formation mechanism of the products was discussed based on the time and temperature-dependent experimental results. The optical properties were characterized by photoluminescence (PL) spectroscopy as well as kinetic decay. Eu2+-doped dependent luminescent intensity was investigated in detail. The prepared BaFBr:Eu2+ phosphors are considered promising materials for fluorescent applications.
研究领域:
材料科学
·
无机化学
·
纳米技术
·
光学材料
·
功能材料
✓ 已验证
DOI
ENVIRONMENTAL SCIENCE AND POLLUTION RESEARCH
·
2019
·Vol. 26
·期 5
·4997-5007
·
IF 2.914
Zhang Lixin,Rao Lei,Wang Peifang,Guo Xiang,Wang Yuxiong
Herein, we present the preparation of nano-TiO 2 –silicone resin composite films by double liquid phase spray deposition. The films exhibit better adhesion stability and photocatalytic activity under a hydrodynamic erosion condition than conventional nano-TiO 2 composite films. The TiO 2 layer morphology and effective TiO 2 coverage ratio (CR) were affected by the initial curing time (ICT) of the silicone resin, e.g., the increase in an ICT from 10 to 40 min resulted in a CR change from 79.1 to 98.7%. The surface morphology evolution of composite films was studied under a hydrodynamic erosion period of 4 weeks. Obtained results allowed the 4-week evolution to be divided into four stages (pitting, crack pregnant, banded stripping, and surface stripping periods), additionally revealed that the CR of all samples was remained above 65%. The photocatalytic activity of composite films before and after 4-week hydrodynamic erosion was evaluated by rhodamine B degradation experiments. The 4-week erosion only led to the decrease of the photodegradation efficiencies by less than 40% in all cases. Thus, the fabricated TiO 2 –silicone composite films demonstrated excellent durability and photocatalytic activity under the conditions of long-term hydrodynamic erosion, allowing one to conclude that this work paves the way to the fabrication of next-generation photocatalytic materials for industrial applications.
研究领域:
材料科学
·
环境科学
✓ 已验证
产品关联
DOI
PubMed
高影响因子
MATERIALS AND CORROSION-WERKSTOFFE UND KORROSION
·
2019
·Vol. 70
·期 6
·1044-1055
·
IF 1.458
Junwei Sheng,Xixun Shen,Yaxue Wang,Qunjie Xu,Xiaoxue Zhang
In this paper, the pure Zn coating and Zn-TiN composite coatings containing four different concentrations of TiN particles were prepared on the carbon steel by direct current electrodeposition. The X-ray diffraction and scanning electron microscopy were used to study the crystal size, preferred orientation, and surface morphology of these coatings. The results show that the incorporation of TiN particles refines the crystal size of the Zn coating and results in the formation of a special surface morphology with papillary-shaped clusters structure that preferentially grows along the (100) crystallographic plane. Such a surface provides better hydrophobicity for the Zn-TiN composite coatings. The corrosion behavior of these coatings was evaluated by potentiodynamic polarization, electrochemical impedance spectroscopy and the long-term immersion test. The results show that the incorporation of TiN nanoparticles leads to a significant increase in corrosion resistance of the Zn coating and there is an optimal addition of TiN nanoparticles to provide a best corrosion resistance for the composite coatings. Additionally, the microhardness of prepared coatings was also evaluated.
研究领域:
材料科学
·
表面工程
·
腐蚀与防护
·
金属功能涂层
·
电化学
✓ 已验证
DOI
高影响因子
VACUUM
·
2023
·
IF 4
Rui Yang,Xiangfeng Guo,Khaled Tawfik Alali,Kun Song,Lihua Jia,Tongle Ge,Xiaoshuang Chen,Dalei Song,Xuefeng Bai,Jun Wang
The construction of effective nano-microstructures electrode has been a tireless pursuit in the energy storage field. Herein, Controllable construction of diversified morphologies NiCo 2 O 4 nanomaterials by tuning the dielectric constant and viscosity of the mixed solvent. We employed different solvent compositions as deionized water (DI), DI:Ethanol (1:1), DI: Isopropanol (1:1), DI: Propylene glycol (1:1), DI: Butanediol (1:1). In mixed aqueous solvents with low dielectric constants of ethanol and isopropanol, metal ions diffuse well and the nanomaterials tend to construct sheet-like nanostructures whereas high viscosity of the propylene glycol and butanediol solution will slow down the rate of metal ion diffusion, which only grow uni-directionally to form rod-like nanostructures. The formed ear-shaped NiCo 2 O 4 nanostructures in V propylene glycol : V H2O = 1 : 1 mixed solvent have a large specific surface area and provide more electrochemically active sites, which facilitates effectively access electrolytes and thus accelerates the redox reaction rate. The resulting NiCo 2 O 4 nanoears exhibits favorable capacity of 251 mAh g −1 and excellent rate performance with a 73.0% capacity retention at 20 A g −1 . More importantly, the asymmetric supercapacitors assembled with the preferred NiCo 2 O 4 nanoears and active carbon (AC) reveal excellent electrochemical performance at operating potential of 1.6 V, great specific capacity (58.0 mAh g −1 ), energy and power density of 46.4 Wh kg −1 at 801 W kg −1 and a specific capacity retention rate of 90.7% after 5000 cycles. This work provides a new perspective for the controllable construction of new micro-nanostructure materials.
研究领域:
材料科学
·
电化学
·
纳米技术
·
能源存储
·
功能材料
·
电化学能量储存
✓ 已验证
DOI
高影响因子
JOURNAL OF POWER SOURCES
·
2017
·
IF 6.395
Yongpeng Cui,Huanlei Wang,Nan Mao,Wenhua Yu,Jing Shi,Minghua Huang,Wei Liu,Shougang Chen,Xin Wang
The increasing demand for supercapacitors with high energy and power density has attracted extensive attention in designing advanced carbon materials with high accessible surface area, hierarchical porosity , and 2D/3D morphology. Here, we report a new approach to tune the morphology and structure of the nanocarbons by using methyl cellulose as the precursor. Due to the varying effect of different activating agents, the interconnected sheet-like carbon with a high surface area of up to 2285 m 2 g −1 and a thickness down to ∼4 nm can be obtained. These important characteristics make the nanocarbons demonstrate a high capacitance of 144 F g −1 at 1 A g −1 and 20 °C, and an excellent capacitance retention ratio of 64% at 100 A g −1 in ionic liquid . Because of the high fraction of meso/macropores for nanocarbons, an outstanding capacitance of 116 F g −1 can be achieved at 0 °C, with a high capacitance retention ratio of 39% at 100 A g −1 . A high energy of 16–17 and 9–10 W h kg −1 can be maintained at 20 and 0 °C when the supercapacitor is charged in less than 1s. The excellent electrochemical response of nanocarbons suggests that the proposed preparation process is promising for developing advanced carbon electrodes.
研究领域:
材料科学
·
电化学
·
纳米科技
·
能源存储
·
功能材料
✓ 已验证
DOI
高影响因子
JOURNAL OF APPLIED POLYMER SCIENCE
·
2021
·Vol. 138
·期 45
·51348
·
IF 3.125
Junming Chen,Jinxuan He,Longquan Liu,Yongzhu He,Xiaobin Huang
Polymeric ablative materials (PAMs) are widely used in spacecraft currently for thermal insulation. However, it is challenging to find a single filler that can improve both ablative and mechanical properties of PAMs. In this study, a new type of hybrid cross-linked polyphosphazene microspheres (PHC) is added to ethylene propylene diene monomer (EPDM) composites as a filler for the first time and its influence on the ablation, mechanical, and thermal properties of EPDM is investigated. The results show that the addition of 3 phr PHC increases the ablation performance by about 10% and enhances the mechanical properties by 20% approximately. In addition, the ablation mechanism is studied in accordance with SEM, FTIR, and Raman spectroscopy. On the one hand, PHC has the effect of catalyzing carbonization, thus increasing the rate of residual carbon; on the other hand, PHC changes the morphology of the char layer, forming a cross-linked structure containing P─O─Si bonds on the surface. The findings regarding catalyzing carbonization and the special char layer structure could guide the design of ablative materials.
研究领域:
高分子材料
·
航天热防护
·
复合材料科学
·
材料化学
·
热力学
✓ 已验证
DOI
高影响因子
JOURNAL OF SOLID STATE CHEMISTRY
·
2012
·
IF 2.159
Mi Wang,Yanfeng Gao,Lei Dai,Chuanxiang Cao,Xuhong Guo
Nanoscaled SnO 2 with different morphologies has been synthesized via a simple hydrothermal process at 180 °C using polyvinylpyrrolidone (PVP), sodium dodecyl sulfonate (SDS), cetyl trimethyl ammonium bromide (CTAB) or tetrapropyl ammonium bromide (TPAB) as surfactant . All the prepared SnO 2 are of a tetragonal crystal structure. Nanocubes, nanorods , nanosheets , nanobelts and nanoparticles were prepared when changing the type and dosage of organic surfactants. It is shown that anionic surfactant (SDS) and cationic surfactant (CTAB or TPAB) at their suitable addition amounts can largely influence the morphologies of SnO 2 nanocrystals . The effect is significantly dependent on the solvent types: water or ethanol. The non-ionic surfactant (PVP) can also change the morphologies like SDS but the impacts are less obvious. The effect of surfactants on the shape and size of SnO 2 nanoparticles was discussed in detail. The particle growth mechanism is described based on the electrostatic interactions and Van der Waals’ forces.
研究领域:
材料科学
·
纳米技术
·
无机化学
·
物理化学
✓ 已验证
DOI
高影响因子
MACROMOLECULAR RAPID COMMUNICATIONS
·
2015
·Vol. 36
·期 15
·1437-1443
·
IF 4.941
Linge Wang,Paul D. Topham,Oleksandr O. Mykhaylyk,Hao Yu,Anthony J. Ryan,J. Patrick A. Fairclough,Wim Bras
Polymer beads have attracted considerable interest for use in catalysis, drug delivery, and photonics due to their particular shape and surface morphology. Electrospinning, typically used for producing nanofibers, can also be used to fabricate polymer beads if the solution has a sufficiently low concentration. In this work, a novel approach for producing more uniform, intact beads is presented by electrospinning self-assembled block copolymer (BCP) solutions. This approach allows a relatively high polymer concentration to be used, yet with a low degree of entanglement between polymer chains due to microphase separation of the BCP in a selective solvent system. Herein, to demonstrate the technology, a well-studied polystyrene-poly(ethylene butylene)–polystyrene triblock copolymer is dissolved in a co-solvent system. The effect of solvent composition on the characteristics of the fibers and beads is intensively studied, and the mechanism of this fiber-to-bead is found to be dependent on microphase separation of the BCP.
研究领域:
高分子科学
·
纳米材料
·
生物医学工程
·
药物递送
·
组织工程
✓ 已验证
DOI
高影响因子
CELLULOSE
·
2016
·Vol. 24
·期 2
·863-870
·
IF 3.195
Chen Haizhen,Chen Jing,Teng Na,Na Haining,Zhu Jin
Residual ethanol was used as an activation agent to control the status of corn cellulose (CN cellulose) solution and thereby the morphology of CN cellulose fibers after electrospinning. A suitable amount of ethanol could combine with the CN cellulose chains to reduce their ionic absorbance, improving the migration ability of ions in the cellulose– N , N -dimethylacetamide (DMAc)/LiCl–ethanol system. As a result, the entanglement of the molecular chains of CN cellulose in solution was reduced. Excess ethanol reduced the migration ability of ions and enhanced the strong entanglement of CN cellulose in solution. By thus adjusting the status of the CN cellulose solution, the fiber morphology and diameter distribution after electrospinning could be controlled. Based on the experimental results, this approach represents an important and effective approach using ethanol as an activation and adjusting agent for CN cellulose to achieve formation of high-quality electrospun fibers.
研究领域:
高分子科学
·
材料科学
·
纤维工程
·
生物材料
·
纳米技术
✓ 已验证
DOI
高影响因子
JOURNAL OF MATERIALS SCIENCE & TECHNOLOGY
·
2017
·Vol. 33
·期 8
·850-855
·
IF 2.764
Nannan Bi,Lei Zhang,Qiang Zheng,Fei Zhuge,Jiupeng Li,Xuan P.A. Gao,Juan Du
A vapor deposition method was applied to synthesize zinc oxide (ZnO) nanowires and nanorods with diameter from 40 nm to 500 nm, length from 1 μm to 70 μm by adjusting the flow rate of argon, oxygen and the pressure during growth. Results of scanning electron microscopy (SEM) and high resolution transmission electron microscopy (TEM) proved the hexagonal wurtzite structure of the synthesized ZnO nanowires or nanorods , which grow along the <0001> direction. The results show that the growth conditions strongly impact the morphology, growth rate and optical properties of the ZnO nanostructures . The ZnO nanowires with small diameters tend to show stronger ultraviolet (UV) light emission from the electron-hole recombination near band edge in photoluminescence (PL), while those with larger diameters tend to exhibit PL spectra dominated by the broad green light emission due to the defects.
研究领域:
材料科学
·
纳米技术
·
半导体物理
·
光电子学
·
功能材料
✓ 已验证
DOI
高影响因子
CERAMICS INTERNATIONAL
·
2022
·Vol. 49
·期 7
·10265-10272
·
IF 5.532
Wenchao Xi,Boxue Song,Zhengyu Sun,Tianbiao Yu,Jun Wang,Qi Sun
To improve the wear resistance of Fe-based cladding, NbC particles with different morphology are generated in situ by adding Nb, Cr 3 C 2 and C with different content. The composition of samples and the morphology of NbC particles generated in situ are revealed by XRD , SEM and EDS. The wear resistance is studied by a reciprocating friction and wear testing machine. The wear mode and the wear mechanism of each sample are investigated. The results show that although NbC particles are generated in situ in samples with different Nb, Cr 3 C 2 and C content, the morphology of NbC particles is varied. The wear resistance of samples containing cross-shaped NbC particles is more outstanding than that of samples containing only rectangular NbC particles. In addition, changing Nb, Cr 3 C 2 and C content does not result in a change in wear mode, but leads to the formation of continuous lattice structure of Cr 0.19 Fe 0.7 Ni 0.11 and Cr 23 C 6 compounds at grain boundaries and a change in the wear resistance. When the additions of Nb, Cr 3 C 2 and C are 11.2 wt%, 8.6 wt% and 0.2 wt% respectively, the coefficient of friction of the sample is the lowest, and the wear resistance is the most outstanding.
研究领域:
材料科学
·
金属学与热处理
·
表面工程
·
摩擦学
·
复合材料
✓ 已验证
DOI
高影响因子
危险品化学品经营许可证（带存储）