Journal of the Taiwan Institute of Chemical Engineers
·
2018
·
IF 3.849
Yafei Guo,Chang Tan,Peng Wang,Jian Sun,Junjie Yan,Weiling Li,Chuanwen Zhao,Ping Lu
Coal and biomass fly ash was impregnated with tetraethylenepentamine (TEPA) to prepare solid CO 2 sorbent. Experimental CO 2 adsorption capacities of the sorbent in fixed-bed column were fitted to several kinetic equations. The modified Avrami fractional kinetic model could accurately predict the CO 2 adsorption kinetic behaviors of the sorbent under different conditions. CO 2 adsorption rate increases with the increase in temperature, initial CO 2 concentration and gas flow rate, as a result of the decreased CO 2 diffusion resistance. A mathematical model was proposed and demonstrated to well predict the CO 2 adsorption breakthrough curves in the fixed-bed column. Effects of temperature, initial CO 2 concentration and gas flow rate on the mass transfer kinetic behaviors of the desired sorbent were investigated. The positive effect of these factors on promoting the overall mass transfer coefficient and the internal mass transfer coefficient is not significant. The external mass transfer coefficient will be remarkably reinforced with the increase in these operating parameters, due to the change in viscosity and density of the gas phase and the reduced external mass transfer resistance. Internal mass transfer process is determined as the rate-limiting step for CO 2 adsorption. The results will lay the groundwork for future scale-up application of the sorbent in post-combustion CO 2 capture.
研究领域:
环境科学
·
化学工程
·
能源工程
·
大气污染控制
·
碳捕集与封存
✓ 已验证
DOI
高影响因子
JOURNAL OF MOLECULAR LIQUIDS
·
2019
·
IF 4.561
Guoli Chen,Kun Song,Xiaoming Huang,Wenbo Wang
Titanium dioxide (TiO 2 ) colloid was synthesized by using tetrabutyl titanate . TiO 2 (KH-570) intermediate was prepared by etherification reaction of TiO 2 colloid and KH-570. The CS-GMA intermediate was prepared by ring-opening reaction of chitosan (CS) and glycidyl methacrylate (GMA). Finally, copolymerization two intermediates obtain a new adsorbent, TiO 2 (KH-570)-g-(CS-GMA). The results manifest that the maximum adsorption amounts of toluene and Pb(II) are 56.62 mg/g and 623.56 mg/g, respectively. The adsorption of TiO 2 (KH-570)-g-(CS-GMA) adsorbent for toluene and Pb(II) accord with the pseudo-second-order kinetics mechanism and Langmuir equation, indicate that the TiO 2 (KH-570)-g-(CS-GMA) adsorbent has better adsorption effect on toluene and Pb(II).
研究领域:
环境科学
·
材料科学
·
化学工程
·
污染控制
·
吸附技术
✓ 已验证
DOI
高影响因子
JOURNAL OF APPLIED POLYMER SCIENCE
·
2013
·Vol. 131
·期 8
·
IF 1.395
Caina Min,Qun Pu,Liu Yang,Hong Fan
A novel polysiloxane bearing dodecyl and epoxy side groups (DESO) was synthesized as an intermediate through hydrosilylation of polymethylhydrosiloxane with allyl glycidyl ether and 1-dodecene. Then, dodecyl/piperazine functional polysiloxane (DPSO) was prepared through the reaction of N -aminoethylpiperazine with DESO. The chemical structure of DPSO was characterized with FTIR and 1 H-NMR spectroscopy and its application performance on cotton fabrics was studied. DPSO with dodecyl side groups gifted the treated fabrics with good wettability and whiteness compared with piperazine functional polysiloxane, while with a slightly reduced softness as well as thickening handle. Film morphology, orientation, and performance on cotton substrates of DPSO were investigated by scanning electron microscope, atomic force microscopy, X-ray photoelectron microscope, and so on. Affected by the dodecyl side groups, DPSO formed relatively hydrophilic, macroscopically smooth but actually uneven films with many dodecyl side chain pillars on the treated substrate surfaces. © 2013 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2014 , 131 , 40186.
研究领域:
高分子化学
·
纺织化学与染整工程
·
材料表面科学
·
功能材料
✓ 已验证
DOI
高影响因子
COLLOIDS AND SURFACES A-PHYSICOCHEMICAL AND ENGINEERING ASPECTS
·
2016
·
IF 2.76
Hao Li,Sirong Yu,Xiangxiang Han,Yan Zhao
Superhydrophobic surface has attracted great attention because of its potential applications. In this work, a facile method for fabrication of a superhydrophobic coating on pipeline steel surface is reported. A hierarchical structured coating with nanoflakes was fabricated via electrodeposition and solution-immersion, and then the coating achieved superhydrophobic with water contact angle about 157° and sliding angle around 3° after fluorination modification. The surface morphology and wettability changed with different experimental parameters were also investigated. The prepared superhydrophobic coating exhibited efficient self-cleaning and anticorrosion properties. Furthermore, the anti-scaling property of this superhydrophobic coating was confirmed since the CaCO 3 crystals on the superhydrophobic coating were mainly needlelike compared to the rhombohedral CaCO 3 crystals on the surface of steel substrate. This superhydrophobic coating maintained good long-term stability in air, and mechanical and thermal stability under certain environment. This superhydrophobic coating provided potential multifunctional applications, such as self-cleaning, corrosion resistance and anti-scaling properties, of deposition metal or alloy coating.
研究领域:
材料科学
·
表面工程
·
腐蚀科学
·
功能涂层
·
金属防护
✓ 已验证
DOI
高影响因子
INDUSTRIAL CROPS AND PRODUCTS
·
2023
·
IF 5.9
Nan Li,Sufeng Zhang,Yali Liu,Valentin Nica,Sergiu Coseri
Cellulose-based materials are currently considered prime candidates for replacing petrochemical plastics because they are biodegradable and cost-effective, while the insufficient hydrophobicity makes them fail to meet application demands, which is a primary issue to be addressed. This work developed a green, catalyst-free approach to prepare high-hydrophobicity amidated cellulose (ADC) by anchoring the COOH-containing oleic acid (OLA) onto NH 2 -containing aminated cellulose (AMC) via amide bonds. The unsaturated fatty acid tail provides a hydrophobic barrier in ADC films . The surface water contact angle of the ADC film reached 133° and remained above 110° for at least one hour. Subsequently, the ADC suspension was applied on the surface of paper from old corrugated container (P-OCC) by an impregnation approach to investigate the improvement of hydrophobic properties. The results showed that the hydrophobicity of P-OCC was increased by ADC, with the water contact angle reached to 132° from 0°. Noticeably, the tensile strength of the ADC impregnated P-OCC (A-POCC) also increased by 2 times. This indicates that with excellent hydrophobicity and mechanical strength , the ADC has great potential application in green functional coating materials.
研究领域:
高分子材料科学
·
表面与界面化学
·
生物质功能材料
·
绿色化学
·
包装材料工程
✓ 已验证
DOI
高影响因子
APPLIED SURFACE SCIENCE
·
2022
·
IF 7.392
Jiemin Han,Yifei Ma,Mei Wang,Zhaomin Tong,Jonghwan Suhr,Liantuan Xiao,Suotang Jia,Xuyuan Chen
Black coatings benefit from low reflectance or high light absorption are utilized in multifarious optical applications. Due to their unique three-dimensional nanostructure and π-band optical transitions, vertical graphene (VG) has drawn great attention to the field of black coatings. However, how the morphology of VGs affects reflectance has not been comprehensively disclosed yet. In addition, the morphology of the substrate for VG growth also affects the absorption properties. Here, we report a nano-and micro-engineered VG/Ni structure based on VG and laser-modified nickel foil, which possesses omnidirectional low reflectance of ∼0.25% over the visible range. A larger spacing of graphene nanowalls is more conducive to the formation of light traps and improves the absorption property. Besides, the surface of nickel substrate by laser irradiation presents a “cauliflower-like” microstructure, which further enhances light-trapping ability.
研究领域:
材料科学
·
光学工程
·
纳米技术
·
表面工程
·
功能涂层
✓ 已验证
DOI
高影响因子
NEW JOURNAL OF CHEMISTRY
·
2019
·Vol. 43
·期 16
·6136-6145
·
IF 3.069
Tianlu Xu,Jinrui Zhang,Lijie Qu,Xueyan Dai,Peihong Li,Yanlong Sui,Chunling Zhang
A phenyl group was introduced into the polymeric network of polysiloxane foam for the improvement of its thermal insulation capacity and thermal stability. Phenyl-containing polysiloxane was prepared via ring-opening polymerization, and phenyl-containing polysiloxane foam was fabricated through simultaneous foaming and crosslinking reactions. With increasing phenyl content, the thermal conductivity of the polysiloxane foam decreased from 0.093 W m−1 K−1 to 0.079 W m−1 K−1. When the phenyl content was 6.15 mol%, the average cell diameter decreased from 384 μm to 165 μm and the cell density increased from 0.58 × 108 cells per cm3 to 4.67 × 108 cells per cm3. When the phenyl content was 8.5 mol%, the cell morphology became imperfect and the average cell diameter and cell density reached 259 μm and 1.29 × 108 cells per cm3, respectively. TGA results revealed the improved thermal stability of the polysiloxane foam. The TGA curves under nitrogen and air conditions could be divided into three stages. Under nitrogen conditions, the mass loss of the maximum decomposition stage decreased and the residue at 800 °C slightly increased. Under air conditions, the maximum decomposition temperatures of the three stages increased. The compressive strength and specific compressive strength were measured and showed a downward trend.
研究领域:
高分子材料科学
·
热功能材料
·
复合泡沫材料
·
材料化学
·
绝缘材料工程
✓ 已验证
DOI
高影响因子
POLYMER BULLETIN
·
2014
·Vol. 71
·期 11
·2923-2944
·
IF 1.491
Yan Huiqiong,Chen Xiuqiong,Wu Tiantian,Feng Yuhong,Wang Chunxiu,Li Jiacheng,Lin Qiang
The surface modification with poly(methyl hydrosiloxane) (PMHS) using a grinding method as a pesticide carrier had been successfully achieved. The characteristics of the modified kaolin were represented by Fourier transform infrared, X-Ray diffraction, BET specific surface area measurements, laser particle size analysis, transmission electron microscopy and contact angle measurement. Subsequently, immobilization of acetamiprid onto clay’s surface was carried out by means of freeze-drying technology. And the drug-loaded clays were encapsulated in alginate-chitosan composite beads by extrusion into calcium chloride solution. The composite beads showed regularly spherical shapes and uniform sizes with diameters of 1.44 ± 0.24–1.75 ± 0.19 mm. The immobilization and release of acetamiprid were carried out to examine the effect of the modified kaolin on the properties of the composite bead. The results showed that the intensive force of superfine pulverization during the grinding process was effective to increase the specific surface areas of the modified kaolin with particle size reduction. The modified kaolins as promising carrier materials had improved the drug loading rate and encapsulation efficiency from 4.15 and 42.01 % for alginate-chitosan composite beads to 6.02 and 82.95 %, which were higher than 4.33 and 54.29 % for SA-CS-kaolin composite beads, respectively. The controlled-release formulation containing the modified kaolin had shown slow and sustained release properties to promote the efficient use of organic pesticide to reduce pollution effect on the environment.
研究领域:
材料科学
·
农业化学
·
药物递送系统
·
环境友好材料
·
粘土矿物加工
✓ 已验证
DOI
高影响因子
EUROPEAN POLYMER JOURNAL
·
2021
·
IF 4.598
Yue Li,Zhencai Qu,Kun Wu,Peng Lv,Huifa Meng,Haoting Zheng,Jun Shi,Mangeng Lu,Xiaomei Huang
In this work, a bio-derived char-forming strategy for surface fireproofing was developed. Specifically, a vinyl-modified tannic acid, (VTA) was synthesized by a ring-opening reaction between tannic acid and glycidyl methacrylate. Integration of epoxy acrylate resin, VTA and tri-(glycidyl methacrylate) phosphate (TGMA), a novel UV-curing coating was prepared, which rendered the PET sheets with superior fireproofing effect. PET samples that were surface coated with the designed UV-curing agent displayed a UL-94 V-0 rating. The peak heat release rate (peak HRR) for combustion of PET was reduced by 10.66% upon application of the flame-retardant coating in cone calorimetry tests. However, the total smoke release (TSR) increased by 48.28% due to pyrolysis of tannic acid produces 1,2,3-benzenetriol and carbon dioxide, plus the triol underwent partial combustion with the formation of large amount of particulates. The thermal behavior of cured coating revealed that the presence of high carbon content aromatic tannic acid promoting cationic crosslink and char formation ability. When 40% VTA was added into a coating, the pyrolysis char yield increased by 36.88%. Furthermore, the capability of inhibit heat transfer with the presence of VTA significantly decreased the maximum rate of weight loss for the coating by 85.97%. The increase in the VTA content promoted crosslinking density of the coating, which leads to good rigidity, outstanding abrasion resistance and remarkable water fastness.
研究领域:
高分子材料
·
阻燃化学
·
表面工程
·
绿色化学
·
材料科学
✓ 已验证
DOI
高影响因子
INTERNATIONAL JOURNAL OF BIOLOGICAL MACROMOLECULES
·
2019
·
IF 4.784
Xiujuan Zhao,Yangyang Luo,Peixin Tan,Mingxian Liu,Changren Zhou
A high-performance oil-water separation device that built by environment-friendly materials is a promising strategy to solve water pollution problem. In this study, we developed an oil-water separation system with chitin/halloysite nanotubes (C/HNTs) composites. C/HNTs were crosslinked by epichlorohydrin and freeze-dried, then a porous sponge was formed. The C/HNTs sponge was modified to be hydrophobic via immersing into bromohexadecane ethanol solution. The surface structure, mechanical properties, microstructure, oil absorption and oil-water separation ability of the C/HNTs sponge were investigated. The addition of HNTs significantly increased the compressive strength of chitin sponge without influence on porous structure . IR spectra indicated the successful coating of bromohexadecane on the C/HNTs sponge surface, which enabled the hydrophobicity and lipophilicity of this construct. The inside construct of the C/HNTs sponges were full of interconnected pores, and the pore size ranged from 250 to 500 μm. The absorption capability for various oil and grease were measured, including methylbenzene, sunflower seed oil , carbon dichloride, n-hexane, chloroform and acetone. It is found that the total amount of chloroform absorbed by a C/HNTs sponge was ~11.23 times of the sponge's weight, and the absorption for hexane was ~3.94 times of the sponge's weight. The sponge also exhibited an excellent oil-water separation ability with as high as 98.7% separation efficiency. All the results suggested that the chitin/HNTs sponges with improved mechanical property would have a great potential in oil-water separation.
研究领域:
材料科学
·
环境工程
·
高分子化学
·
纳米复合材料
·
分离技术
✓ 已验证
DOI
高影响因子
INTERNATIONAL JOURNAL OF ADHESION AND ADHESIVES
·
2016
·
IF 1.956
Abbas Hasan Faris,Mohamad Nasir Mohamad Ibrahim,Afidah Abdul Rahim
Tannin-glyoxalated Kraft lignin (TGKL) resin is a successful substitution for phenol formaldehyde resin in the production of wood adhesives, however it has a poor water resistance. To overcome this obstacle, this research was focused on scalable adhesive through the modified tannin adhesive and oligomeric precursors of a hyperbranched poly (amine-ester) (HBPAE). The prepared glyoxalated Kraft lignin resin (MTGKL), TGKL, HBPAE and commercial phenol formaldehyde (CPF) resin were evaluated by FTIR , 1 H and 13 C NMR spectroscopy . The tensile strengths and thermal stability were determined. The results indicated that the addition of HBPAE to tannin adhesive could improve the water resistance of MTGKL. This was evident when soaking plywood bonded with TGKL in cool water, where delamination occurred, but it was not evident with MTGKL. The tensile results indicated that the adhesive strengths of MTGKL, 39.72 MPa (dry) and 27.62 MPa (wet), were higher compared to TGKL and CPF resins.
研究领域:
高分子材料
·
林产化学加工
·
胶体与界面科学
·
可持续材料
·
生物质转化
✓ 已验证
DOI
高影响因子
CONSTRUCTION AND BUILDING MATERIALS
·
2016
·
IF 2.421
Changqing Fang,Xin Yu,Ruien Yu,Pei Liu,Xiaoting Qiao
Isocyanate modified asphalt samples were got by adding quantitative isocyanate into the base asphalt. Isocyanate and nano particles composite modified asphalt samples were produced by adding quantitative isocyanate and three different kinds of inorganic nanoparticles (Silicon dioxide, Titanium dioxide, Zinc oxide) into the base asphalt respectively. Isocyanate modified asphalt, isocyanate and nanoparticles composite modified asphalt were characterized by taking physical tests, SEM, fluorescence microscopy, TG and FTIR tests, which demonstrated that the high and low temperature performance of isocyanate and nano particles composite modified asphalt had been improved effectively. From the microscopic view, the modification of the base asphalt was very significant. Results also indicated that the temperature sensitivity of composite modified asphalt had been decreased. Meanwhile, the thermal stability had been improved when compared with the base asphalt and isocyanate modified asphalt.
研究领域:
材料科学
·
道路工程
·
高分子化学
·
纳米技术
·
应用化学
✓ 已验证
DOI
高影响因子
危险品化学品经营许可证（带存储）