Results in Physics
·
2023
·
IF 5.3
Meijie Zhu,Hua Xu,Zuoquan Tan,Le Wang
Large-area and uniform two-dimensional (2D) non-layered α-MnSe was successfully synthesized via the molecular sieve modified chemical vapor deposition (CVD). The molecular sieve serves both as a filter and a container to controllable release the Mn precursor in a stable and much lower concentration, leading to the uniform growth of 2D α-MnSe flakes. The thickness, crystalline quality and uniformity of the as-grown α-MnSe are further characterized. Our study validated the positive role of molecular sieve in the controllable growth of 2D α-MnSe, which is believed to be applicable to other non-layered transition metal chalcogenides (TMCs) and will be beneficial for their further applications in electronics, optoelectronics and spintronics.
研究领域:
材料科学
·
纳米科技
·
凝聚态物理
·
无机化学
✓ 已验证
DOI
高影响因子
CHINESE CHEMICAL LETTERS
·
2019
·Vol. 31
·期 8
·2099-2102
·
IF 3.839
Xin Yu,Ding Wang,Yuqiu Wang,Ji Yan,Xianying Wang
In this work, the two-dimensional MoS 2 film was prepared by sulfuring the molybdenum atomic layer on SiO 2 /Si substrate. The reaction temperature, heating rate, holding time and carrier gas flow rate were investigated comprehensively. The quality of MoS 2 film was characterized by optical microscopy, atomic force microscopy, Raman and photoluminescence spectroscopy. The characterization results showed that the optimum synthesis parameters were heating rate of 25 °C/min, reaction temperature of 750 °C, holding time of 30 min and carrier gas velocity of 100 sccm. The MoS 2 gas sensor was fabricated and its gas sensing performance was tested. The test results indicated that the sensor had a good response to both reducing gas (NH 3 ) and oxidizing gas (NO 2 ) at room temperature. The sensitivity to 100 ppm of NO 2 was 31.3%, and the response/recovery times were 4 s and 5 s, respectively. In addition, the limit of detection could be as low as 1 ppm. This work helps us to develop low power and integrable room temperature NO 2 sensors.
研究领域:
材料科学
·
纳米科技
·
传感器技术
·
环境监测
·
半导体物理
✓ 已验证
DOI
高影响因子
JOURNAL OF MATERIALS SCIENCE & TECHNOLOGY
·
2017
·Vol. 33
·期 8
·850-855
·
IF 2.764
Nannan Bi,Lei Zhang,Qiang Zheng,Fei Zhuge,Jiupeng Li,Xuan P.A. Gao,Juan Du
A vapor deposition method was applied to synthesize zinc oxide (ZnO) nanowires and nanorods with diameter from 40 nm to 500 nm, length from 1 μm to 70 μm by adjusting the flow rate of argon, oxygen and the pressure during growth. Results of scanning electron microscopy (SEM) and high resolution transmission electron microscopy (TEM) proved the hexagonal wurtzite structure of the synthesized ZnO nanowires or nanorods , which grow along the <0001> direction. The results show that the growth conditions strongly impact the morphology, growth rate and optical properties of the ZnO nanostructures . The ZnO nanowires with small diameters tend to show stronger ultraviolet (UV) light emission from the electron-hole recombination near band edge in photoluminescence (PL), while those with larger diameters tend to exhibit PL spectra dominated by the broad green light emission due to the defects.
研究领域:
材料科学
·
纳米技术
·
半导体物理
·
光电子学
·
功能材料
✓ 已验证
DOI
高影响因子
JOURNAL OF PHARMACEUTICAL AND BIOMEDICAL ANALYSIS
·
2013
·
IF 2.947
Chen Li,Feng Xu,Chen Cao,Ming-Ying Shang,Cui-Ying Zhang,Jie Yu,Guang-Xue Liu,Xuan Wang,Shao-Qing Cai
Traditional Chinese medicines (TCM) can be identified by experts according to their odors. However, the identification of these medicines is subjective and requires long-term experience. In this paper, electronic nose, headspace gas chromatography–mass spectrometry (GC–MS) and chemometrics methods were applied to differentiate two species of Asari Radix et Rhizoma by their odors. The samples used were the dried roots and rhizomes of Asarum heterotropoides var. mandshuricum (AH) and Asarum sieboldii (AS). The electronic nose was used to determine the odors of the samples and enabled rapid differentiation of AH and AS when coupled with principal component analysis. Headspace GC–MS was utilized to reveal the differences between the volatile constituents of AH and AS. In all, 54 volatile constituents were identified, and 9 major constituents (eucalyptol, eucarvone, 3,5-dimethoxytoluene, 3,4,5-trimethoxytoluene, methyleugenol, 2,3,5-trimethoxytoluene, croweacin, pentadecane and asaricin) could be used as chemical markers to distinguish these two species. AH contained higher relative contents of eucarvone (1.79–16.76%), 3,5-dimethoxytoluene (6.64–26.52%), 3,4,5-trimethoxytoluene/methyleugenol (6.43–31.67%) and 2,3,5-trimethoxytoluene (1.64–6.66%), whereas AS had higher relative contents of eucalyptol (14.06–24.95%), croweacin (5.64–13.55%), pentadecane (8.44–20.82%) and asaricin (7.03–13.45%). Moreover, AH and AS could be distinguished according to the contents of either all 54 identified volatile constituents or only the 9 major constituents by employing cluster analysis. The proposed method is rapid, simple, eco-friendly and can successfully differentiate these two species of Asari Radix et Rhizoma by their odors.
研究领域:
中药鉴定
·
分析化学
·
天然药物化学
·
代谢组学
·
药用植物学
✓ 已验证
DOI
高影响因子
APPLIED SURFACE SCIENCE
·
2019
·
IF 5.155
Yao Zhu,Huan Yi,Qiaoyan Hao,Jidong Liu,Yuxuan Ke,Zhuo Wang,Dianyuan Fan,Wen jing Zhang
Monolayer WS 2 (1L-WS 2 ) possesses direct band gap, which is beneficial for light emitting applications. However, high quality sample obtained via mechanical exfoliation suffers from ultralow yield of large flakes while large 2D material monolayers synthesized by chemical vapour deposition (CVD) unintentionally induce many defects, resulting in low photoluminescence (PL) intensity. Herein, we firstly control the 1L-WS 2 scalable growth through H 2 introduction at the beginning of the CVD synthesis. Its domain size can be increased from 1 μm up to 20 μm with higher coverage, compared to that synthesized without H 2 introduction. Then, we propose scalable ways to anneal the obtained large 1L-WS 2 in Ar diluted hydrogen sulfide (H 2 S) atmosphere at 750 °C or to treat it with (3-mercaptopropyl) trimethoxysilane (MPS). Its PL intensity can be increased to 12 times by H 2 S or more interestingly to 30 times by MPS, respectively. Our systematic analyses show that the drastic PL improvements are mainly attributed to the reduction of structural defects by H 2 S and MPS, which is facilitated via the H– bond in them. The results help to explore routes to obtaining large-size single crystalline transition metal dichalcogenides monolayer (1L-TMDCs) and intense PL emission.
研究领域:
材料科学
·
纳米科技
·
凝聚态物理
·
表面科学
·
半导体材料
✓ 已验证
DOI
高影响因子
JOURNAL OF MATERIALS SCIENCE-MATERIALS IN ELECTRONICS
·
2019
·Vol. 30
·期 18
·17440-17446
·
IF 2.195
Wang Tianxiong,Meng Xianquan
We try to synthesize In x Ga 1−x Sb nanowires on silicon (100) substrate using InSb and GaSb as source materials and we succeeded. Au film was used as catalysts. The experiment is simple and repeatable. The diameter of the grown nanowires is 60–200 nm and up to 10 microns in length. The grown nanowires have good crystallinity. Due to the doping of indium, we found that the XRD peaks of nanowires were shifted. We have fabricated fully nanostructured device using ultra-long Ag nanowires as electrodes for the I–V characteristic study, and found that the device has photoresponse characteristics and the I–V characteristic curve was asymmetric, we explain that it was due to the asymmetry of this fully nanostructured devices.
研究领域:
材料科学
·
纳米科技
·
半导体物理
·
固体电子学
·
晶体生长
✓ 已验证
DOI
高影响因子
JOURNAL OF ANALYTICAL AND APPLIED PYROLYSIS
·
2020
·
IF 3.905
Yanshuxian Liu,Yilei Fan,Zhongping Huang,Huijun Liu,Lili Wang,Zhenlu Shen,Ichi Watanabe
A novel method based on on-line pyrolytic methylation-gas chromatography/mass spectrometry was established and applied into rapid determination of γ-hydroxybutyric acid (GHB) in human hair. With the pyrolytic methylation by tetramethylammonium hydroxide (TMAH), GHB was converted into its corresponding methyl ester in the pyrolyzer at 500 °C. Thus, GHB in hair samples could be well determined by GC/MS on a capillary column in SIM mode. To obtain optimum methylation conditions, important factors were investigated and then applied to the following experiments. The results were obtained as following: 500 °C as reaction temperature, 2:1 as the proportion of TMAH to GHB. The achieved calibration curve exhibited good linearity with the correlation coefficient of 0.9997 at the concentraion range of 2−200 ng/mg, and relative standard deviation (n = 3) from 1.3 %–7.7 %. The limit of detection and the limit of quantification were down to 0.3 ng/mg and 1.0 ng/mg, respectively. The precision ranged from 2.0 %–7.9 % and the recovery ranged from 98.5 %–107.4 %. The results of on-line pyrolytic methylation-GC/MS were in agreement with those observed by the referenced off-line silylation-GC/MS method. The method was applied to a real case of a woman addicted to GHB, the drug concentration in hair segments of 0−5 cm and 5−10 cm from the root strand well correlated with the use of GHB in different periods of her life. The proposed method demonstrated significant potential in the application of rapid determination for GHB in human hair.
研究领域:
法医毒理学
·
药物代谢
·
分析化学
·
生物样本分析
·
临床化学
✓ 已验证
DOI
高影响因子
DALTON TRANSACTIONS
·
2022
·Vol. 52
·期 2
·376-383
·
IF 4.569
Enming Ping,Lingyun Kong,Mengyao Liu,Yunshan Zhou,Lijuan Zhang,Nan Chen
The reaction of porous γ-Al2O3 particles acting as both a sacrificial template and an aluminum source with 1,4-naphthalene diacid (H2NDC) resulted in the formation of γ-AlOOH@Al(OH)(1,4-NDC) composites, in which ZIF-67 was then loaded by the in situ crystallization method, leading to the formation of γ-AlOOH@Al(OH)(1,4-NDC)@ZIF-67 composites. The deliberately designed composite was used to separate H2/D2 at 77 K in a 1 m chromatographic column. The results demonstrated that the optimized composite can achieve the effective separation of H2/D2 in gas chromatography due to the additive effects of kinetic sieving and chemical affinity quantum sieving of Al(OH)(1,4-NDC) and ZIF-67. By optimizing chromatographic separation conditions, the resolution R reached 2.02 with the separation time t = 7.72 min. The composite also showed satisfactory repeatability and reproducibility.
研究领域:
材料科学
·
分离科学
·
物理化学
·
纳米材料
·
能源化学
✓ 已验证
DOI
高影响因子
CHINESE JOURNAL OF CATALYSIS
·
2013
·Vol. 34
·期 12
·2161-2166
·
IF 1.304
Mingming Zhang,Manman Jiang,Changhai Liang
A basic anion exchange resin , Amberlite IRA-900, was loaded with Pd(C 3 H 5 )(C 5 H 5 ) by an easy metal-organic chemical vapor deposition (MOCVD) approach to give Pd@IRA-900 catalyst after reduction at room temperature . Ultraviolet-Visible spectroscopy results showed a red shift of the absorption peak of Pd 2+ after the Pd precursor was loaded on the resin, indicating that a chemical reaction occurred between the precursor and the support. Pd nanoparticles with 2.6 nm of average size were well dispersed on the support. The Pd@IRA-900 catalyst showed high activity for different kinds of aryl halides in Suzuki-Miyaura coupling reactions under mild and aerobic conditions. Excellent recyclability of Pd@IRA-900 catalyst was also observed in the Suzuki-Miyaura coupling reaction of iodobenzene and phenylboronic acid . A bifunctional catalyst Pd@IRA-900(OH) was synthesized by pretreating the ion exchange resin support with NaOH before Pd loading, which successfully catalyzed the Suzuki-Miyaura reaction of iodobenzene and phenylboronic acid without base under aerobic conditions.
研究领域:
催化化学
·
有机合成
·
材料化学
·
绿色化学
·
纳米催化
✓ 已验证
DOI
高影响因子
Physica Status Solidi-Rapid Research Letters
·
2023
·Vol. 18
·期 2
·2300183
·
IF 2.8
Lei Xu,Mengtong Yang,Qidong Lu,Yuxin Ren,Yi Chen,Jinjia Guo,Mingjie Cai,Xiao Miao,Feng Teng,Haibo Fan,Chunmei Zhang,Xuexia He,Peng Hu
Broadband photodetectors are essential for the integrated design of next-generation optical detector devices. Ternary 2D bismuth sulfide semiconductor (BiXI, X = S, Se, Te) is an ideal candidate for broadband photoelectric detection due to its narrow bandgap and excellent electrical transport performance. Here, BiSeI is grown by chemical vapor transport (CVT) method and used in photoelectrochemical (PEC) photodetection. The PEC-type photodetector based on BiSeI nanosheets has a broadband detection ranging from 350 to 900 nm, displaying a high responsivity of 2.88 mA W −1 , a high detectivity of 1.10 × 10 10 Jones and a fast response time of 7/16 ms at a bias voltage of 0.5 V. Furthermore, the device also exhibits a negligible current density loss after three months, which indicates that it has good stability against air and moisture. In addition, the photodetector can work without bias potential, indicating that it is a good self-powered device. The results demonstrate that BiSeI is a potential material in self-powered PEC photodetector.
研究领域:
材料科学
·
纳米科技
·
光电子学
·
半导体物理
·
电化学
✓ 已验证
DOI
高影响因子
CERAMICS INTERNATIONAL
·
2024
·Vol. 51
·期 5
·6587-6598
·
IF 5.1
Bo Li,Yigao Chen,Shaopeng Wang
A (ZrC/SiC) 35 multilayer alternating coating with 500∼700 nm sublayers thickness and 70 interfaces was deposited on sharp leading edge C/C composites by continuous CVD method. Its mechanical property and ablation resistance were assessed by scratch test and oxy-acetylene flame respectively and compared with ZrC monolayered coating. The (ZrC/SiC) 35 multilayer alternating coating exhibited a high bonding strength via the regulation of sub-micro alternating stress field and the inhibition of crack propagation by 70 interfaces, showing a high critical load L C3 of 22.521 N, which was higher than that of ZrC monolayered coating of 5.688 N. Furthermore, the coating revealed excellent ablation resistance evidenced by its intact oxide layer, and the mass and linear ablation rates were only 0.17 mg/s and 0.87 μm/s respectively. The layer-by-layer oxidation behavior allowed the advantages of ZrC and SiC sublayers to be fully utilized, thus maintaining the layered oxide structure. Furthermore, the total 35 layers of thin ZrO 2 layers improved the fault tolerance ability of coating in harsh ablative environments.
研究领域:
材料科学
·
表面工程
·
高温防护涂层
·
复合材料
·
力学性能
·
热防护系统
✓ 已验证
DOI
高影响因子
Sustainable Energy & Fuels
·
2021
·Vol. 5
·期 5
·1538-1547
·
IF 6.367
Ruyan Lei,Yanping Yang,Chenjuan Yu,Yinsi Xu,Yuanzhuo Li,Jun Li
In order to improve the electrochemical performance and efficiently prepare a solid polymer electrolyte (SPE) for the lithium-metal battery (LMB), a fumed SiO2 (FS) with surface Si–OH group was used to fabricate FS-modified poly(ethylene oxide) (PEO)–LiClO4-based SPE by a facile preparation process. The influences of the FS content on the morphological properties, thermal properties, lithium salt dissociation, mechanical properties, and electrochemical properties of SPE were systematically analyzed. Results indicate that FS with the hydrophilic property was widely distributed throughout the amorphous phase of SPE, thus the crystallinity of SPE was reduced to 25.83% when the FS mass loading was 6.85 wt%. In addition, a greater dissociation degree of lithium salt was achieved after the addition of FS, and a higher ion conductivity of 3.03 × 10−4 S cm−1 and Li-ion migration number of 0.396 were recorded at 60 °C. The all-solid-state Li/SPE/Li coin cell showed excellent stable cyclability (380 h) and the LiFePO4 (LFP)/SPE/Li coin cell demonstrated good discharge specific capacity and coulomb efficiency of 96 mA h g−1 and 100.2%, respectively, after 100 cycles of galvanostatic charge–discharge operation under 0.5C at 60 °C. Thus, based on collective results, it is expected that SPE presented in this work is a promising electrolyte for next-generation high-energy all-solid-state LMB with enhanced safety.
研究领域:
材料科学
·
电化学
·
能源存储
·
高分子化学
·
固态离子学
✓ 已验证
DOI
高影响因子
危险品化学品经营许可证（带存储）