Journal of Materials Research and Technology-JMR&T
·
2022
·
IF 6.267
Zhiping Zhang,Yuenan Wang,Yang Lei,Fang Zhang,Xiaobing Chen,Hongfei Liu
Negative thermally expanded (NTE) (KMg) x Sc 2-x (WO 4 ) 3 (0 = x ≤ 1.5) ceramics have been prepared via solid-state reaction. X-ray diffraction (XRD) analysis reveals that (KMg) x Sc 2-x (WO 4 ) 3 undergoes a composition-induced phase transition as the (KMg) 3+ -substitution content increases. For x = 0.25, both hexagonal (KMg) x Sc 2-x (WO 4 ) 3 and orthorhombic Sc 2 (WO 4 ) 3 coexisted in the sample. For 0.25 < x ≤ 1, a single-phase, hexagonal (KMg) x Sc 2-x (WO 4 ) 3 , was obtained. When x is further increased to 1.25, monoclinic MgWO 4 impurity was detected in the sample. Meanwhile, as x increases, the grain size of (KMg) x Sc 2-x (WO 4 ) 3 ceramics grows up. Hexagonal (KMg) x Sc 2-x (WO 4 ) 3 ceramics show high densification and strong NTE property. Thermomechanical analysis indicates that the linear coefficients of thermal expansion (CTEs) of hexagonal (KMg) x Sc 2-x (WO 4 ) 3 ceramics decrease from −7.48 × 10 −6 °C −1 to −14.06 × 10 −6 °C −1 with the increase of x. High-temperature XRD analysis reveals that hexagonal (KMg) 0.5 Sc 1.5 (WO 4 ) 3 show an anisotropic NTE. The intrinsic linear CTEs are α a = α b = −6.74 × 10 −6 °C −1 , α c = 11.03 × 10 −6 °C −1 and the volumetric CTE is α v = −2.52 × 10 −6 °C −1 .
研究领域:
材料科学
·
无机非金属材料
·
功能陶瓷
·
热学性能
·
结构与物性
✓ 已验证
DOI
高影响因子
CERAMICS INTERNATIONAL
·
2020
·Vol. 47
·期 4
·4769-4774
·
IF 3.83
Hongfei Liu,Chenjun Zhang,Zhiping Zhang,Xiangdong Meng,Xianghua Zeng
Orthorhombic Sc 2 Mo 3 O 12 films have been successfully prepared via spin coating technique followed by annealing at 500–750 °C. The phase composition, microstructure, morphology and negative thermal behavior of the synthesized Sc 2 Mo 3 O 12 films were investigated. XRD and XPS analysis indicate that as-deposited film is amorphous . Orthorhombic Sc 2 Mo 3 O 12 films can be prepared after post-annealing at 500–750 °C for 1 h. The crystallinity of Sc 2 Mo 3 O 12 films gradually improved with the increase of post-annealing temperature. SEM analysis shows as-deposited film is smooth and compact, and the grain size of Sc 2 Mo 3 O 12 film grows up as the post-annealing temperature increases. Variable temperature XRD analysis demonstrates that the synthesized orthorhombic Sc 2 Mo 3 O 12 films show stable thermo-chemical and anisotropic NTE property in 25–700 °C. The corresponding coefficients of thermal expansion (CTEs) of the orthorhombic Sc 2 Mo 3 O 12 film in a, b and c directions are −6.68 × 10 −6 °C −1 , 5.08 × 10 −6 °C −1 and −4.76 × 10 −6 °C −1 , respectively. The whole unit cell of the orthorhombic Sc 2 Mo 3 O 12 film shrinks and the volumetric CTE of the Sc 2 Mo 3 O 12 thin film is −6.36 × 10 −6 °C −1 , and the linear CTE is about −2.12 × 10 −6 °C −1 ( α v = 3 α l ).
研究领域:
材料科学
·
无机非金属材料
·
功能薄膜
·
热学性能
·
晶体结构
✓ 已验证
DOI
高影响因子
Results in Physics
·
2022
·
IF 4.565
Yige Du,Qilong Gao,Andrea Sanson,Hengli Xie,Yangming Hu,Gaojie Zeng,Juan Guo,Xiao Ren,Erjun Liang
Negative thermal expansion (NTE) is an intriguing physical phenomenon, which is of great significance for the high precision application. In this work, we have realized to broaden the NTE temperature zone in Mg 2 P 2 O 7 -based bulk material by doping Cu atom on the Mg site. A joint study of Raman scattering and X-ray diffraction (XRD) indicates that there are double phases in the NTE temperature zone, and the NTE of Mg 1.9 Cu 0.1 P 2 O 7 bulk material comes from the phase transition of α - and β -phase. The present work provides a way to optimize negative thermal expansion property in phase transition typed materials.
研究领域:
材料科学
·
凝聚态物理
·
无机化学
·
功能材料
·
热学性能
✓ 已验证
DOI
高影响因子
INTERNATIONAL JOURNAL OF ENERGY RESEARCH
·
2020
·Vol. 44
·期 11
·8555-8566
·
IF 3.741
Li Yang,Yanping Yuan,Nan Zhang,Yanfang Dong,Yafen Sun,Wenhui Ji
Summary To make better use of solar energy, lauric acid/expanded graphite (LA/EG) composite phase change materials (PCMs) were synthesized to collect and store solar energy as latent heat thermal energy. The results of thermal characteristics show that when the mass fraction of EG is 5%, 10%, and 15%, the latent heat of LA/EG is 164.5, 156.9, and 148.0 J/g, and the thermal conductivity is 2.73, 7.98, and 10.54 W/(m·K). Leakage test shows that LA/EG PCMs with EG mass fraction of 10% and 15% are form stable after phase change. One thousand thermal cycles prove good thermal reliability of LA/EG. TG analysis indicates LA/EG PCMs have good thermal stability within operating temperature range. The Ultraviolet-visible spectra reveal that the absorbance of LA/EG composite PCMs would increase as the mass fraction of EG increases. Photothermal conversion experiment results indicate that the photothermal conversion efficiency of LA/EG composite PCMs increases as the mass fraction of EG increases, and the efficiency can reach 95% when the mass fraction of EG is 15%. Moreover, it was also found that the process of photothermal conversion can be accelerated with stronger illumination intensity or smaller heat transfer size. All the results show that the prepared LA/EG PCMs can convert solar energy into thermal energy and store it in the form of latent heat at the same time, which indicates it has promising prospect in the application of solar energy conversion and storage.
研究领域:
材料科学
·
能源化学
·
热能工程
·
功能材料
·
可再生能源
✓ 已验证
DOI
高影响因子
CERAMICS INTERNATIONAL
·
2024
·Vol. 50
·期 14
·25541-25547
·
IF 5.1
Hang Zhang,Ahsan Nawaz,Feiyu Huang,Zhiping Zhang,Hongfei Liu
Orthorhombic In 0.5 Sc 1.5 Mo 3 O 12 thin films have been synthesized using the sol-gel spin coating . Influences of post-annealing temperatures on crystal structure, morphology, negative thermal expansion (NTE) and optical performances of the thin films were studied using XRD , SEM, XPS, high-temperature XRD and UV–Vis–NIR spectrophotometer. XRD and SEM results show that as-prepared thin film is in an amorphous state with a smooth and dense surface. Orthorhombic In 0.5 Sc 1.5 Mo 3 O 12 thin films were obtained after post-annealing in 550–750 °C. The higher the annealing temperature in 550–750 °C, the better the crystallinity of orthorhombic In 0.5 Sc 1.5 Mo 3 O 12 thin films . In addition, the grain size of the In 0.5 Sc 1.5 Mo 3 O 12 thin film also grows as the annealing temperature increases. The resulting orthorhombic In 0.5 Sc 1.5 Mo 3 O 12 thin films exhibit anisotropic NTE. Its volumetric coefficient of thermal expansion (CTE) is −3.44 × 10 −6 °C −1 , while the CTEs in a -, b - and c -axis directions are −4.70 × 10 −6 °C −1 , 5.37 × 10 −6 °C −1 , and -4.10 × 10 −6 °C −1 in 25–700 °C, respectively. In addition, the transmittance of orthorhombic In 0.5 Sc 1.5 Mo 3 O 12 thin films post-annealed at 750 °C is around 87.75 %–95.03 %.
研究领域:
材料科学
·
无机非金属材料
·
功能薄膜
·
热膨胀调控
·
光学材料
✓ 已验证
DOI
高影响因子
CERAMICS INTERNATIONAL
·
2023
·Vol. 49
·期 14
·23410-23416
·
IF 5.2
Xuewei Luo,Shuo Huang,Ruiqi Huang,Chunhui Xu,Shuen Hou,Hongyun Jin
Single-phase high-entropy rare-earth zirconate (Dy 0.2 Nd 0.2 Sm 0.2 Eu 0.2 Yb 0.2 ) 2 Zr 2 O 7 with excellent high-temperature phase stability at 1600 °C was designed and synthesized. After being heated at 1600 °C for 1 ∼ 50 h, the average grain size of the sample increases only from 0.74 μm to 2.22 μm, indicating a high anti-sintering ability. The fracture toughness is 2.07 ± 0.03 MPa m 1/2 (25 °C), which is 50% higher than lanthanum zirconate. The local lattice distortions induced by the atomic interactions and atomic-size mismatch are considered to be responsible for the strong anti-sintering ability and improved fracture toughness. In addition, the thermal expansion coefficient and thermal conductivity of (Dy 0.2 Nd 0.2 Sm 0.2 Eu 0.2 Yb 0.2 ) 2 Zr 2 O 7 are 10.59 × 10 -6 K -1 (25 ∼ 1500 °C) and 1.14 ± 0.09 W·m -1 ·K -1 (1500 °C), respectively. The outstanding combination of anti-sintering ability, mechanical behavior , and thermophysical properties of (Dy 0.2 Nd 0.2 Sm 0.2 Eu 0.2 Yb 0.2 ) 2 Zr 2 O 7 highlights its great potential for next-generation thermal barrier coating applications.
研究领域:
材料科学
·
无机非金属材料
·
高温功能材料
·
热障涂层技术
·
固态化学
✓ 已验证
DOI
高影响因子
INTERNATIONAL JOURNAL OF ENERGY RESEARCH
·
2020
·Vol. 45
·期 4
·5337-5346
·
IF 3.741
Chuangang Yao,Jixing Yang,Haixia Zhang,Sigeng Chen,Jian Meng,Kedi Cai
Summary Cu doped perovskites SrFe 0.9- x Cu x Mo 0.1 O 3- δ (SFCM, x = 0-0.2) are explored as cathodes for IT-SOFCs. The influence of Cu doping on the property of SFCM series was studied in detail. The oxygen content decreases with the increase of Cu doping amount. SFCM samples are chemically compatible with LSGM electrolyte. However, the TEC values are still a bit higher than that of some common SOFC electrolytes. At 750°C, the R p values are 0.261, 0.227 and 0.155 Ω·cm 2 for SFCM0, SFCM0.1, and SFCM0.2. The obtained activation energies for x = 0, 0.1, and 0.2 are 1.01, 0.98, and 0.87 eV, respectively. These results indicate that Cu doping into SrFe 0.9- x Cu x Mo 0.1 O 3- δ has a favorable effect on the electrochemical activity of the materials.
研究领域:
材料科学
·
电化学
·
能源材料
·
固体氧化物燃料电池
·
无机功能材料
✓ 已验证
DOI
高影响因子
CHEMICAL ENGINEERING JOURNAL
·
2020
·
IF 10.652
Mengdi Yuan,Chao Xu,Tieying Wang,Tianying Zhang,Xinyu Pan,Feng Ye
The serious supercooling of erythritol (ET) limits its application in the field of mid-temperature thermal energy storage (TES), especially in the recently developed form-stable phase change materials (PCMs). The primary purpose of this paper is to find out the factors to mitigate the supercooling of ET/expanded graphite (EG) form-stable composite PCM and obtain the correlation among the morphology, kinetic parameters, and a supercooling degree in the non-isothermal crystallization process. Firstly, five types of supercooling relaxation agents (nano-Al 2 O 3 , nano-SiO 2 , CMC, urea, and citric acid) were added to prepare the ET/EG form-stable CPCMs. Among them, the ET/EG/nano-Al 2 O 3 exhibited excellent form-stable ability, a high heat release ratio of 78.9%, and the lowest supercooling degree (Δ T ) of 45.7 °C. Based on the chosen ET/EG/nano-Al 2 O 3 CPCM, the tablet pressures from 1 to 13 MPa were applied, obtaining lowest Δ T decreased by 59.0% in 1 MPa. Moreover, the non-isothermal crystallization processes were discussed on the ET/EG/nano-Al 2 O 3 with the Avrami equation modified by Jeziorny. ET tended to grow spherulites under the high cooling rate of 18 °C/min with triggering as the Johnson-Mehl-Avrami exponent n increased to 4.22. Meanwhile, the supercooling degree increased from 48.8 to 56 °C with the cooling rate growing from 2 to 18 °C/min. And the activity energy Δ E of the ET/EG/nano-Al 2 O 3 CPCM (7092.35 kJ/mol) was smaller than that of the ET/EG CPCM (8211.19 kJ/mol) because of the interaction between the heterogeneous nucleation effect and blocker effect of nano-Al 2 O 3 .
研究领域:
材料科学
·
热能存储
·
物理化学
·
复合材料
·
能源材料
✓ 已验证
DOI
高影响因子
FLUID PHASE EQUILIBRIA
·
2018
·
IF 2.197
Xiaopo Wang,Kai Kang,Shanshan Zhu,Bo Gao
In this work, experimental density data were reported for six fatty acid methyl esters , including methyl butyrate , methyl valerate , methyl caproate , methyl pelargonate , methyl heptanoate , and methyl caprylate . The densities were measured from 293.15 K to 363.15 K and pressures up to 60 MPa by a vibrating-tube densimeter . The relative uncertainty of the measurement is estimated less than 0.001 with a confidence level of 0.95. The high pressure densities were correlated with a Tait-type equation. The overall average relative deviation between experimental data and calculated results from Tait equation for the six fatty acid esters is 0.010%. The derived thermodynamic properties, such as isobaric thermal expansivity and isothermal compressibility , were obtained from the experimental density results. Additionally, for the studied esters, the molecular parameters of the PC-SAFT equation of state were obtained based on the corresponding vapor pressures and liquid densities. The PC-SAFT equation was used to predict the high pressure densities of the esters, and good agreements were observed.
研究领域:
化学工程
·
热力学
·
流体物理化学
·
生物燃料
✓ 已验证
DOI
高影响因子
SURFACE & COATINGS TECHNOLOGY
·
2019
·
IF 3.192
Lu Zhu,Yousen Zhu,Xuanru Ren,Ping Zhang,Jianghao Qiao,Peizhong Feng
MoSi 2 -MoB-ZrO 2 composite powders are one-step synthesized prepared by self-propagating high-temperature synthesis (SHS), which are further utilized to prepare the oxidation protective coatings by spark plasma sintering (SPS) method on molybdenum substrate. Microstructure and properties of the coatings were investigated and determined. Oxidation behavior of the coatings at high temperature was also studied. The results showed that the composite coating is dense and crack-free due to the addition of ZrO 2 , which is beneficial for the decrease of mismatch in coefficient of thermal expansion, and no void exists in the diffusion layer owing to the diffusion of Si, which is inhibited by adding MoB. Compared with the pure MoSi2 coating, the high hardness of the composite coating is enhanced by about 20% while the fracture toughness of the composite coating is improved by about 25%, which makes the occurrence of intergranular fracture , crack deflection and crack bridging. After oxidation at 1400 °C for 80 h, MoSi 2 coating failed while xMoSi 2 -MoB-3ZrO 2 (x = 3, 4, 5) composite coating still kept its protective effect. Only a little substrate is consumed during oxidation and improved oxidation resistance is gained by MoSi 2 -MoB-ZrO 2 composite coating. 3MoSi 2 -MoB-3ZrO 2 coating shows the relatively best oxidation resistance due to the formation of crack-free oxide film on the surface of the coating.
研究领域:
材料科学
·
表面工程
·
高温氧化
·
陶瓷涂层
·
粉末冶金
✓ 已验证
DOI
高影响因子
RSC Advances
·
2019
·Vol. 9
·期 59
·34658-34670
·
IF 3.049
Xiangyu Wang,Yu Xie,Jun Ma,Ping Ning
The two-stage removal process of tetracycline (TC) in aqueous solutions using a novel photocatalyst based on nano-zero-valent iron (NZVI), g-C3N4 and expanded graphite by carbon layer (EGC) is reported for the first time. The composite (NZVI/g-C3N4@EGC) exhibits remarkable adsorption, reduction ability and visible light activity over the reaction course. Compared with pristine g-C3N4 (25.9%) and pure NZVI (45.9%), NZVI/g-C3N4@EGC achieves high degradation efficiency of TC (98.5%) due to the formation of a heterogeneous photo-Fenton system. This study shows that synergistic effects are achieved in the reaction system, including maintaining the reduction ability of NZVI and enhancing the photocatalytic activity of g-C3N4 by facilitating the separation of photogenerated electrons (e−) and holes (h+). TC removal involved a two-stage process of adsorption–reduction and photo-degradation. The quencher experiments determined that holes (h+) and superoxide radicals (˙O2−) are the major reactive species in the degradation of TC. The degradation pathways of TC were proposed based on the analysis of the intermediates. In addition, NZVI/g-C3N4@EGC revealed a high stability in a five-cycle test and good magnetic properties for facile separation from aqueous solutions. From an application viewpoint, NZVI/g-C3N4@EGC has favorable prospects in the direction of the photocatalytic degradation of antibiotic wastewater.
研究领域:
环境化学
·
材料科学
·
光催化
·
水污染治理
·
纳米复合材料
·
抗生素降解
✓ 已验证
DOI
高影响因子
CERAMICS INTERNATIONAL
·
2024
·Vol. 51
·期 8
·10774-10782
·
IF 5.1
Jitao Yi,Xinyue Zhang,Shanliang Chen,Ting Sun,Qinghui Jiang,Yong Liu
BiCuSeO-based materials show great promise for thermoelectric generators in waste heat recovery due to their excellent thermoelectric properties. However, the limited focus on device development has hindered their industrial-scale implementation. Here, high-performance BiCuSeO-based compounds with exceptional thermal stability were synthesized and remained stable aging for 400 h, making them suitable for investigation in the device bonding process. The BiCu80AgP is identified as the optimal solder from eight candidates, effectively connecting the copper (Cu) electrode with BiCuSeO-based compounds. The optimized bonding process substantially resulted in an impressive interfacial shear strength of about 15 MPa and reduced interfacial resistance to 2.2 mΩ cm 2 . Interface analysis revealed the formation of diverse, complex compounds, with variations in their concentrations greatly affecting joint performance. Achieving a uniform distribution of these compounds effectively mitigated thermal expansion mismatches and extended joint longevity by a factor of 6.6. This research proposes a novel fabrication method for BiCuSeO-based thermoelectric devices utilizing BCu80AgP solder, providing a foundation for future advancements in this field.
研究领域:
材料科学
·
热电转换
·
固态物理
·
能源材料
·
界面工程
✓ 已验证
DOI
高影响因子
危险品化学品经营许可证（带存储）