JOURNAL OF NON-CRYSTALLINE SOLIDS
·
2019
·
IF 2.6
Ang Qiao,Haizheng Tao,Yuanzheng Yue
Amorphous conductors with high ionic conductivity are a promising candidate as electrolytes in all-solid state batteries. In this work, we prepared amorphous Ag 3 PS 4 conductor via a chemo-mechanical milling process, and then characterized its structure and electrochemical properties . The results show that Ag + conductivity of the amorphous Ag 3 PS 4 was remarkably enhanced by three orders of magnitude compared to its crystalline counterpart. Furthermore, the amorphous sample exhibits lower activation energy ( E a ) for ionic conductivity as a function of temperature. Structural characterizations indicate that the tetrahedral [PS 4 ] units were retained in amorphous Ag 3 PS 4 , but the Ag + ions became more liberated than those in the crystalline state, leading to the enhanced migration of Ag + ions, thereby, the ionic conductivity in amorphous Ag 3 PS 4 is drastically increased. This work provides insight into the crucial role of the disorder in raising the ionic conductivity of amorphized chalcogenide materials containing mobile ions.
研究领域:
材料科学
·
固体化学
·
能源材料
·
电化学
·
无机非金属材料
·
固态电池
·
离子传导
✓ 已验证
DOI
高影响因子
INTERNATIONAL JOURNAL OF HYDROGEN ENERGY
·
2014
·Vol. 39
·期 7
·3313-3319
·
IF 2.93
Jing Lin,Fei Liang,Yaoming Wu,Wanqiang Liu,Limin Wang
We prepared Ti 1.4 V 0.6 Ni ribbons by arc-melting and subsequent melt-spinning techniques. Ti 1.4 V 0.6 Ni + x Mg ( x = 1, 1.5, 2, 2.5 and 3, wt.%) composite alloys were obtained by the mechanical ball-milling method. The structures and hydrogen storage properties of alloys were investigated. Ti 1.4 V 0.6 Ni + x Mg composite alloys contained icosahedral quasicrystalline phase, Ti 2 Ni-type phase, β-Ti solid-solution phase and metallic Mg. The electrochemical and gaseous hydrogen storage properties of alloys were improved with Mg addition. Ti 1.4 V 0.6 Ni + 2 Mg alloy showed maximum electrochemical discharge capacity of 282.5 mAh g −1 as well as copacetic high-rate discharge ability of 82.3% at the discharge current density of 240 mA g −1 compared with that of 30 mA g −1 , and the cycling life achieved above 200 mAh g −1 after 50 consecutive cycles of charging and discharging. The hydrogen absorption/desorption properties of Ti 1.4 V 0.6 Ni + x Mg ( x = 1, 2 and 3, wt.%) alloys were better than Ti 1.4 V 0.6 Ni. Ti 1.4 V 0.6 Ni + 3 Mg alloy also exhibited a favorable hydrogen absorption capacity of 1.53 wt.%. The improvement in the hydrogen storage characteristics caused by adding Mg may be ascribed to better hydrogen diffusion and anti-corrosion ability.
研究领域:
材料科学
·
金属功能材料
·
储能材料
·
物理化学
·
电化学
✓ 已验证
DOI
高影响因子
ELECTROCHIMICA ACTA
·
2013
·
IF 3.777
Heng Zhang,Yi Lu,Chang-Dong Gu,Jian-Bin Cai,Xiu-Li Wang,Jiang-Ping Tu
Amorphous Ni–P–C films are fabricated by combining the electrodeposition of Ni–P films from a eutectic-based ionic liquid and the direct current magnetron sputtering of amorphous carbon top-layer. The carbon top-layer with a thickness of about 10 nm is homogeneously coated on the surface of the Ni–P films. A comparison study is undertaken between Ni–P and Ni–P–C films to evaluate the microstructure and the electrochemical performances of the composite films as anode materials for lithium ion batteries , which allow the decoupling of the effect of the carbon layer . It is found that at lower discharge–charge current densities, the cyclability of both Ni–P and Ni–P–C films is similar. As the discharge–charge current density increases, the Ni–P–C film exhibits improved capability and reversibility over the Ni–P film. The Ni–P–C film delivers an initial discharge capacity of 1060 mAh g −1 at 250 mA g −1 and the capacity retention after 50 cycles is 62%, much higher than that of the Ni–P film (51%). The cyclability of Ni–P–C film at different discharge–charge current densities from 200 to 500 mA g −1 is also much better than those of Ni–P film. This study indicates that the introduction of a carbon top-layer on Ni–P film could significantly improve the electrochemical performances due to the decreased interface electric resistance and the structure stability.
研究领域:
材料科学
·
电化学
·
纳米材料
·
能源存储
·
薄膜技术
✓ 已验证
DOI
高影响因子
SOLID STATE IONICS
·
2017
·
IF 2.354
Leyu Zhan,Yao Zhang,Xiangyang Zhuang,Hui Fang,Yunfeng Zhu,Xinli Guo,Jian Chen,Zengmei Wang,Liquan Li
The x LiBH 4 -Li 3 N ( x = 1, 2, 4) composites were investigated on their lithium ionic conductivities . They maintained the original phase structures of orthorhombic LiBH 4 and hexagonal β-Li 3 N during ball milling according to the analyses by X-ray diffraction (XRD) and Fourier transform infrared spectroscopy (FTIR). Electrochemical impedance spectra (EIS) tests showed that LiBH 4 -Li 3 N composites lift the lithium ionic conductivities from that of bulk LiBH 4 by nearly 100 times at low temperature. LiBH 4 -Li 3 N offers 1.06 × 10 − 5 S cm − 1 of conductivity while bulk LiBH 4 possesses only 2.05 × 10 − 7 S cm − 1 at 323 K. Cyclic voltammetry (CV) tests indicated that the voltage window of composites could attain 3 V, which is much more stable than Li 3 N (< 1 V). No thermodynamic incident appears in DSC curves except for the orthorhombic-hexagonal transition endothermic peak of LiBH 4 in the x LiBH 4 -Li 3 N composites. It confirms the phases stabilities of the x LiBH 4 -Li 3 N ( x = 1, 2, 4) composites before and after CV tests. In-situ solid state Nuclear Magnetic Resonance (NMR) tests on LiBH 4 -Li 3 N illustrated that the high conductivity in low temperature should not come from high-temperature phase of LiBH 4 . Therefore, the enhancement of lithium ionic mobility of the composite might be attributed to both Li 3 N and the interfaces between small crystallites where transmission electron microscope (TEM) morphology showed the appearance of amorphous grain boundary.
研究领域:
材料科学
·
固态离子学
·
能源化学
·
电化学
·
纳米材料
·
固体电解质
·
锂离子电池
✓ 已验证
DOI
高影响因子
RSC Advances
·
2015
·Vol. 5
·期 87
·70743-70748
·
IF 3.84
Zhiwei Liu,Ping Li,Fuqiang Zhai,Qi Wan,Alex A. Volinsky,Xuanhui Qu
Nanostructured tungsten carbide with high surface area and containing amorphous carbon is prepared by a low temperature combustion synthesis method. The nanostructured tungsten carbide is used as the catalyst in a gas diffusion electrode. The obtained WC with different carbon content was investigated by XRD, FESEM, TG-DTA, BET and XPS. When the molar ratio of C/W is 19/3, the WC particles with different carbon content are obtained after a carbonizing process between 900 and 1400 °C, and the content of free carbon in WC also increases gradually with temperature. The carbon content is tested by the high frequency combustion-infrared absorption method in a carbon sulfur analyzer. The electrochemical properties of the tungsten carbide for the oxygen reduction reaction are characterized by its polarization curves and electrochemical impedance. The results show that the presence of the appropriate amorphous carbon is beneficial for improving the conductivity and dispersibility of the tungsten carbide catalyst, and more active centers can be provided by the catalyst.
研究领域:
材料科学
·
电化学
·
纳米催化
·
能源材料
·
表面科学
✓ 已验证
DOI
高影响因子
JOURNAL OF SOLID STATE CHEMISTRY
·
2017
·
IF 2.299
Yuan-Zi Xu,Cheng-Zong Yuan,Xue-Ping Chen
To design highly efficient and low-cost electrocatalysts for oxygen evolution reaction (OER) is a great challenge for electrochemical water splitting. Here we introduce a simple and cost-effective strategy for one-step synthesis of a three-dimensional Ni 3 S 2 /MoS X (x is close to 3) nanosheets on Ni foam (NF) via a sovelthermal reaction. The electrochemical performance of the Ni 3 S 2 /MoS X nanosheets on NF has been investigated and exhibits superior OER electrocatalytic activity as well as excellent electrochemical durability. As a novel non-noble-metal OER catalyst operating in basic electrolytes, this 3D cathode exhibits an onset overpotential of as low as 165 mV, a Tafel slope of 67.5 mV dec −1 and remarkable long-term stability. This catalyst maintains its catalytic activity for at least 14 h and only affords 50, 100, and 150 mA cm −2 OER current densities at overpotentials of 215 mV, 265 mV and 305 mV respectively.
研究领域:
材料科学
·
电化学
·
能源化学
·
纳米科技
·
催化化学
✓ 已验证
DOI
高影响因子
Small
·
2024
·Vol. 20
·期 26
·2310387
·
IF 13
Wei Luo,Yanli Yu,Yucheng Wu,Wenbin Wang,Yimin Jiang,Wei Shen,Rongxing He,Wei Su,Ming Li
Rational design of heterostructure catalysts through phase engineering strategy plays a critical role in heightening the electrocatalytic performance of catalysts. Herein, a novel amorphous/crystalline (a/c) heterostructure (a-CoS/Ni 3 S 2 ) is manufactured by a facile hydrothermal sulfurization method. Strikingly, the interface coupling between amorphous phase (a-CoS) and crystalline phase (Ni 3 S 2 ) in a-CoS/Ni 3 S 2 is much stronger than that between crystalline phase (c-CoS) and crystalline phase (Ni 3 S 2 ) in crystalline/crystalline (c/c) heterostructure (c-CoS/Ni 3 S 2 ) as control sample, which makes the meta-stable amorphous structure more stable. Meanwhile, a-CoS/Ni 3 S 2 has more S vacancies (S v ) than c-CoS/Ni 3 S 2 because of the presence of an amorphous phase. Eventually, for the oxygen evolution reaction (OER), the a-CoS/Ni 3 S 2 exhibits a significantly lower overpotential of 192 mV at 10 mA cm −2 compared to the c-CoS/Ni 3 S 2 (242 mV). An exceptionally low cell voltage of 1.51 V is required to achieve a current density of 50 mA cm −2 for overall water splitting in the assembled cell (a-CoS/Ni 3 S 2 || Pt/C). Theoretical calculations reveal that more charges transfer from a-CoS to Ni 3 S 2 in a-CoS/Ni 3 S 2 than in c-CoS/Ni 3 S 2 , which promotes the enhancement of OER activity. This work will bring into play a fabrication strategy of a/c catalysts and the understanding of the catalytic mechanism of a/c heterostructures.
研究领域:
材料科学
·
电化学
·
催化化学
·
纳米材料
·
能源材料
✓ 已验证
DOI
高影响因子
Small
·
2023
·Vol. 19
·期 41
·2302685
·
IF 13.3
Hancheng Ma,Xiang Huang,Luyu Li,Wei Peng,Sheng Lin,Yao Ding,Liqiang Mai
PtTe 2 , a member of the noble metal dichalcogenides (NMDs), has aroused great interest in exploring its behavior in the hydrogen evolution reaction (HER) due to the unique type-II topological semimetallic nature. In this work, a simple template-free hydrothermal method to obtain the phosphorus-doped (P-doped) PtTe 2 nanocages with abundant amorphous and crystalline interface (A/C-P-PtTe 2 ) is developed. Revealed by density functional theory calculations, the atomic Te vacancies can spontaneously form on the basal planes of PtTe 2 by the P doping, which results in the unsaturated Pt atoms exposed as the active sites in the amorphous layer for HER. Owing to the defective structure, the A/C-P-PtTe 2 catalysts have the fast Tafel step determined kinetics in HER, which contributes to an ultralow overpotential ( η = 28 mV at 10 mA cm −2 ) and a small Tafel slope of 37 mV dec −1 . More importantly, benefiting from the inner stable crystalline P-PtTe 2 nanosheets, limited decay of the performance is observed after chronopotentiometry test. This work reveals the important role of the inherent relationship between structure and activity in PtTe 2 for HER, which may bring another enlightenment for the design of efficient catalysts based on NMDs in the near future.
研究领域:
材料科学
·
电化学
·
纳米催化
·
能源材料
·
计算材料学
✓ 已验证
DOI
高影响因子
DIAMOND AND RELATED MATERIALS
·
2019
·
IF 2.29
Qiuying Chang,Hao Zhang,Rongqin Gao
A new nanocomposite was prepared by combining Magnesium silicate hydroxide (MSH) with decomposed gelatin under one-pot hydrothermal synthesis conditions. The chemical reaction process involved the MSH formation and the gelation decomposing into carbonaceous species. The characterization of resultant nanoparticles revealed that the nanocomposite was a combination of hydrogenated amorphous carbon and MSH. And the addition of gelatin during synthesis increased the content of granular nanoparticles in nanocomposite samples. The results of tribological experiments of MSH modified by carbon (MSH@C) as lubricant additive showed that the nanocomposites presented much better anti-wear property and friction stability than the MSH without modification. Thus MSH@C nanocomposites were expected to be a promising candidate for lubricant additives. The amorphous carbon film was detected on the wear scar which might account for the significant tribological property.
研究领域:
材料科学
·
纳米科技
·
表面工程
·
摩擦学
·
复合材料
✓ 已验证
DOI
高影响因子
CERAMICS INTERNATIONAL
·
2024
·Vol. 50
·期 12
·21859-21868
·
IF 5.1
Haiyan Guo,Kuibao Zhang,Yuxiang Li
In this work, the irradiation response of A 2 Ti 2 O 7 (A represents rare earth elements of Gd, Dy, Ho, Er, Yb and Nd) series ceramics were systematically studied under 3 MeV Au 2+ ions. The structural changes pre- and post-irradiation were characterized using X-ray diffraction (XRD), grazing incidence X-ray diffraction (GIXRD) and Raman spectroscopy . After heavy ion irradiation , all the samples undergo structural transformations from ordered pyrochlore to disordered fluorite and then to amorphous phase. The sample surface became fully amorphous when exposed to the maximum irradiation dose. The 5RETO high-entropy pyrochlore exhibits the lowest rate of amorphization during the process of structural transformation. The cation radius ratio and mixed entropy are the primary factors influencing amorphization rate. The cation radius ratio shows a strong positive correlation with the amorphization rate, while the mixed entropy demonstrates a weak negative correlation with the amorphization rate. The cation radius ratio can thus serve as a reliable indicator for predicting the radiation resistance of high-entropy pyrochlore ceramics.
研究领域:
材料科学
·
核材料
·
固态化学
·
辐射效应
·
无机非金属材料
✓ 已验证
DOI
高影响因子
JOURNAL OF POWER SOURCES
·
2019
·
IF 7.467
Cheng Lin,Liuzhang Ouyang,Chaojin Zhou,Renzong Hu,Lichun Yang,Xusheng Yang,Huaiyu Shao,Min Zhu
Potassium-ion batteries (PIBs) are becoming one of the promising alternative metal-ion battery systems to lithium-ion batteries due to the abundance and low cost of potassium . Among the anode materials for the metal-ion battery systems, phosphorus-based materials are attractive due to the low cost and their high theoretical-specific capacity. Herein, for the first time, we report the selenium -phosphorous-carbon (Se–P–C) amorphous composites prepared by the plasma-assisted ball milling method as the high-performance anode material for PIBs. In particular, when the amorphous Se–P composite anode with the molar ratio of 1:2 and the P-milling time of 30 h (Se–2P/C@30 h), the associated PIB delivers a high reversible capacity of 634 mA h g −1 at a current density of 0.05 A g −1 and excellent rate capability of 248.6 mA h g −1 at a current density of 1 A g −1 . Furthermore, the experimental characterization and analysis reveal the reaction mechanisms that K–P (K 2 P 3 ) and K–Se (KSe) phases are formed during the potassiation process. The present work provides a facile approach to achieve a promising anode material for K-ion batteries, and the preparation route can be viewed as a reference for the further development of phosphorous-based anodes with high capacity and long cycle life for PIBs.
研究领域:
材料科学
·
电化学
·
能源存储
·
纳米材料
·
无机化学
✓ 已验证
DOI
高影响因子
Journal of Materials Chemistry A
·
2013
·Vol. 1
·期 35
·10184-10192
·
IF 0
Jie Shao,Xuezhang Xiao,Lixin Chen,Xiulin Fan,Leyuan Han,Shouquan Li,Hongwei Ge,Qidong Wang
A system of 2LiH–MgB2 and its hydrogenated 2LiBH4–MgH2 is an attractive candidate for hydrogen storage. However, its hydriding–dehydriding kinetics have to be further improved for practical application. In the present work, three kinds of Ni–B nanoparticles with different crystalline states and particle sizes were prepared by wet-chemical reduction and mechanochemical methods, and then introduced into a 2LiH–MgB2 composite for catalytic enhancement. The catalytic roles of Ni–B nanoparticles on the hydriding–dehydriding properties were investigated systematically. The results show that all of the Ni–B nanoparticles can significantly enhance the hydriding–dehydriding kinetics of the 2LiH–MgB2 composite, resulting in no incubation period for the formation of MgB2 during dehydrogenation. The more disordered the amorphous structure and the smaller sized the Ni–B particles are, the better the catalytic effect that is obtained. Microstructure analyses clearly reveal the formation of the MgNi3B2 phase in the dehydriding process, which acts as the nucleation agent for MgB2 formation determined by an edge-to-edge model. Directly doping with Ni–B nanoparticles in the 2LiH–MgB2 system shows a higher hydrogen desorption capacity of 9.4 wt% and obtains a better catalytic efficiency than doping with NiCl2.
研究领域:
材料科学
·
储能材料
·
无机化学
·
纳米催化
·
氢储存
✓ 已验证
DOI
危险品化学品经营许可证（带存储）