计算溶液所需的质量、体积或浓度。
在卫生保健行业中对伤者或病人进行治疗及护理的工作人员,易接触到可以传播疾病的生物液体,这些由各种微生物引起的疾病会对生命和健康造成严重危害,尤其是可引起肝炎[乙肝病毒 HBV、丙肝病毒 HCV]和获得性免疫缺陷综合症(AIDS)[人类免疫缺陷病毒 HIV]的血源性疾病,由于工程学控制不能消除所有接触可能,因此人们通过使用防护用品来减少体液与皮肤的接触。
阿拉丁合成血液(GB 19083)又称合成血、人工血液、人造血、模拟体液等,是参考国家标准GB19083-2010、GB19082-2009及医疗行业标准YY/T 0700-2008等由羧甲基纤维素钠、氯化钠、吐温、磷酸盐、苋菜红、MIT等配制而成,pH值约为7.2~7.4,主要用于防护用品如口罩、面罩、防护服等材料的抗血液和体液穿透性能的测试,注意避免污染,根据需要可在使用前按照GB/T 5549-1990测量本产品的表面张力,结果应是0.042N/m±0.002N/m。该试剂仅用于科研领域,不适用于临床诊断或其他用途。
自备材料:
1、穿透试验箱、支撑网、气源、环境试验箱、计时器、测厚仪、天平、量筒、防护用品
2、异丙醇
操作步骤(以口罩为例,仅供参考):
1、样品数量:应使用5个口罩样品进行试验。
2、预处理:口罩样品在16~26℃、相对湿度80~85%的环境试验箱中预处理至少4小时。
3、样品固定:将口罩固定于支撑网上使得合成血能喷射到靶区上。
4、安装机器:喷射头安装在距试样靶区290~310mm的位置。
5、喷射试验:将2ml合成血以10.7kPa(80mmHg)、16.0kPa(120mmHg)或21.3kPa(160mmHg)等适当的压力喷向试样,并保证喷到靶区。
6、结果检查:在合成血喷向靶区后9~11s检查试样观测面,在合适的光照条件下注意在口罩的观测面是否有合成血出现或能表明合成血出现的迹象。
注:更具体的操作方法:口罩穿透试验按照YY/T 0469 2011和GB 19083 2010进行;医用面罩穿透试验按照YY/T 0691 2008进行;防护服穿透试验按照GB 19082 2009和YY/T 0700 2008进行。
注意事项:
1、样品在16~26℃、相对湿度80~85%的环境试验箱中预处理至少4小时。
2、如果样品有皱褶,应将皱褶充分展开后固定于支撑网,以保证靶区为单层材料。
3、喷射试验在试样从环境试验箱取出后60s内进行。
4、产品如果出现明显的絮状物或沉淀物应弃用。
5、为了您的安全和健康,请穿实验服并戴一次性手套操作。
6、试剂开封后请尽快使用,以防影响后续实验效果。
Healthcare professionals involved in the treatment and care of injured or ill patients may be exposed to potentially infectious biological fluids. Diseases caused by various microorganisms can pose serious threats to human health and safety, particularly bloodborne infections such as hepatitis B (caused by hepatitis B virus, HBV), hepatitis C (caused by hepatitis C virus, HCV), and acquired immunodeficiency syndrome (AIDS, caused by human immunodeficiency virus, HIV). Since engineering controls cannot completely eliminate the risk of exposure, personal protective equipment (PPE) is used to minimize contact between potentially infectious bodily fluids and the skin.
Aladdin Synthetic Blood (GB 19083), also known as artificial blood, simulated blood, or simulated body fluid, is formulated with sodium carboxymethyl cellulose, sodium chloride, Tween, phosphate salts, amaranth, MIT, and other components, with reference to the Chinese national standards GB 19083-2010 and GB 19082-2009, as well as the medical industry standard YY/T 0700-2008. The product has a pH of approximately 7.2–7.4 and is primarily used to evaluate the resistance of protective materials, including face masks, face shields, and protective clothing, to penetration by synthetic blood and bodily fluids. Care should be taken to prevent contamination during handling and testing. If necessary, the surface tension of the product should be measured before use in accordance with GB/T 5549-1990, with a specified value of 0.042 ± 0.002 N/m. This reagent is intended for research use only and is not suitable for clinical diagnosis or other purposes.
Materials and Equipment Required (Not Supplied):
1. Synthetic blood penetration test apparatus, specimen support mesh, compressed air supply, environmental conditioning chamber, timer, thickness gauge, analytical balance, graduated cylinder, and personal protective equipment
2. Isopropyl alcohol
Experimental Procedure (Using a Face Mask as an Example, For Reference Only):
1. Specimen Quantity: Five face mask specimens should be used for the test.
2. Specimen Conditioning: Condition the specimens in an environmental chamber maintained at 16–26 °C and 80–85% relative humidity for at least 4 hours.
3. Specimen Mounting: Secure the face mask specimen onto the support mesh, ensuring that the synthetic blood can be directed onto the designated target area.
4. Apparatus Setup: Position the spray nozzle at a distance of 290–310 mm from the target area of the specimen.
5. Synthetic Blood Penetration Test: Spray 2 mL of synthetic blood onto the specimen at an appropriate test pressure of 10.7 kPa (80 mmHg), 16.0 kPa (120 mmHg), or 21.3 kPa (160 mmHg), ensuring that the spray is directed toward the designated target area.
6. Result Evaluation: Inspect the observation surface of the specimen 9–11 seconds after the synthetic blood has been sprayed onto the target area. Under appropriate lighting conditions, visually examine the observation surface of the face mask for visible synthetic blood or any evidence of synthetic blood penetration.
Note: For detailed test procedures, refer to YY/T 0469-2011 and GB 19083-2010 for face mask penetration testing; YY/T 0691-2008 for medical face shield penetration testing; and GB 19082-2009 and YY/T 0700-2008 for protective clothing penetration testing.
Precautions:
1. Condition the specimens in an environmental chamber at 16–26 °C and 80–85% relative humidity for at least 4 hours before testing.
2. If wrinkles or folds are present, carefully flatten the specimen before securing it to the support mesh to ensure that the target area consists of a single layer of material.
3. Perform the synthetic blood penetration test within 60 seconds of removing the specimen from the environmental conditioning chamber.
4. Discard the product if visible flocculent matter or precipitates are observed.
5. For personal safety, wear a laboratory coat and disposable protective gloves when handling this product.
6. Use the reagent as soon as possible after opening to prevent any adverse effects on subsequent experimental results.
| pH | 7.2–7.4 |
|---|