Journal of Environmental Chemical Engineering
·
2022
·
IF 7.968
Mengting Wang,Han Ye,Xiongkai Zheng,Siyuan Chen,Huanhuan Xing,Xueqin Tao,Zhi Dang,Guining Lu
Cadmium (Cd 2+ ) and fluoride (F - ) are frequently detected simultaneously in wastewater. Simultaneous removal of Cd 2+ and F - in wastewater is urgent. In this study, bovine bone meal (BBM), mainly consisted of hydroxyapatite , was used as a green adsorbent for Cd 2+ and F - adsorption in single and binary solutions. The results showed that with the increase of pH, the uptake ability of BBM towards Cd 2+ and F - showed an upward and downward trend, respectively, suggesting that electrostatic interaction was an important mechanism. Cl - and NO 3 - had little effect on Cd 2+ and F - adsorption, while H 2 PO 4 - enhanced adsorption capacities. The kinetic data of Cd 2+ and F - removal were successfully described by pseudo-second order model. The maximum adsorption capacity (q m ) of Cd 2+ obtained from the Langmuir model was 78.969 mg/g. The adsorption isotherm of F - was consistent with S-type and satisfied with the Brunauer, Emmett, and Teller (BET) model. In the binary system, F - slightly decreased the adsorption capacity of BBM on Cd 2+ , while Cd 2+ increased the adsorption capacity of BBM on high-concentration F - from 38.724 to 86.966 mg/g. This study provides a cost-effective and environmentally friendly method for separate and simultaneous removals of Cd 2+ and F - from water, which provides a practicable way for the treatment of cadmium-fluorine wastewater and resource utilization of bovine bone.
研究领域:
环境科学
·
废水处理
✓ 已验证
产品关联
DOI
高影响因子
WATER AIR AND SOIL POLLUTION
·
2023
·Vol. 234
·期 3
·1-12
·
IF 2.9
Liu Caiying,Liu Yanyan,Feng Jiapeng,Li Yaru,Tao Jun,Xie Xiaoxiao
The paper aims to evaluate the effectiveness of biochar prepared from the co-pyrolysis of rice husk and cow bone (RHCBC) for in situ remediation and amelioration of Cd-contaminated soil. Effects of RHCBC on Cd bioavailability in soil and Cd uptake in corn growth were investigated through cultivation experiments and pot experiments. The results showed that the addition of RHCBC in the Cd-contaminated soil achieved the increase of soil pH, CEC, and SOM, whereas the soil available Cd content was reduced by 29.08–51.06%, which was proved by the transformation of Cd from acid soluble and exchangeable state to residual state. Furthermore, the nutrient contents of soil were also increased by 82.41–230.09% for alkali-hydrolyzable N, 66.81–144.03% for available P, and 16.20–77.70% for available K, respectively, which promoted the growth of corn. Overall, it is a promising strategy to employ RHCBC for in situ remediation of Cd-contaminated soil and promotion of plant growth as efficient soil amendment.
研究领域:
土壤科学
·
环境修复
·
农业科学
✓ 已验证
产品关联
DOI
高影响因子
LWT-FOOD SCIENCE AND TECHNOLOGY
·
2020
·
IF 4.006
Ting Zhang,Rui Sun,Mengzhen Ding,Li Li,Ningping Tao,Xichang Wang,Jian Zhong
Both fish gelatins and mammalian gelatins have been explored in the preparation and application of fish oil-loaded emulsion. However, the comprehensive comparisons and relationships of the structural, functional, and emulsions stability differences between these two gelatins remain unclear. In this work, structural, functional, and the emulsion application differences between commercial cold-water fish skin gelatin (CFG) and bovine bone gelatin (BBG) are explored. The results demonstrated the BBG-stabilized emulsion was more stable than the CFG-stabilized emulsion at 4 °C and higher temperatures (23 °C and 37 °C) decreased the creaming stability differences. The creaming index differences between CFG-stabilized and BBG-stabilized emulsions were mainly dependent on emulsion droplet size and interfacial layer thickness consisted of gelatins. Further, the possible reason for CFG's lower emulsion stability at 4 °C might be mainly dependent on its higher β-antiparallel percentage in the secondary structures and its lower thickness of gelatin film-like nanostructures. This work will provide useful information to understand the relationship between structure and function of protein. It also will provide a guide for the application of fish oil-loaded gelatin-stabilized emulsions in food beverages and other foods such as surimi .
研究领域:
食品科学
·
生物化学
✓ 已验证
DOI
高影响因子
INTERNATIONAL JOURNAL OF BIOLOGICAL MACROMOLECULES
·
2024
·
IF 7.7
Xin Zhang,Jijun Ding,Haixia Chen,Haiwei Fu,Jiayuan Xu
With the development of superhydrophobic materials for oil-water separation, there is an urgent need to develop environmentally friendly, low-cost, and novel hydrophobic materials. In this paper, based on bovine bone biomass raw materials, bone ash particles are obtained by calcination and grinding, and then bovine bone ash/cotton fabric cellulose membranes are prepared by vacuum filtration and impregnation methods. The pore size of the membrane is regulated and the hydrophobicity of the material is enhanced by constructing the surface microstructures. Results indicate that the membranes possess good hydrophobicity with a contact angle of 161° and the flux can reach 53,635.2 L/m 2 h for light oil. The separation efficiencies for petroleum ether, cyclohexane, kerosene, and dichloromethane all reach >99 %. In addition, the separation efficiency of the cellulose membrane is still >99 % in the 40-day separation test and always exceeds 90 % for 30 cycling test, indicating that it has good stability and recoverability. Interestingly, the cellulose membrane is prepared from biodegradable and renewable raw materials, which reduces environmental pollution and effectively utilize natural resources.
研究领域:
材料科学
·
环境科学
✓ 已验证
DOI
PubMed
高影响因子
INTERNATIONAL JOURNAL OF BIOLOGICAL MACROMOLECULES
·
2024
·
IF 7.7
Yan Xiao,Lingxia Sun,Qian Ding,Miaoyun Li,Yaodi Zhu,Jong-Hoon Lee,Shengzhao Li,Gaiming Zhao,Yican Wang,Yuying Wang,Lijun Zhao
In the food industry, the emulsifying process alters both the stability and quality of the emulsified products prepared by bovine bone high-temperature hydrolysate (BBHH). The microstructure and interactions of BBHH emulsion were characterized by cryo-scanning electron microscopy (Cryo-SEM) and Raman spectroscopy during emulsification. Notably, BBHH emulsion exhibited the best properties under emulsifying for 120 s, attributed to its interfacial adsorption characteristics. In terms of microstructure, the droplets were small and uniform, and the cross-linking and network structure between the droplet surfaces were obvious at 120 s. Raman spectroscopy indicated that the adsorption of BBHH at the oil-water interface mainly involved an increase of the β-sheet at the expense of the α-helix region. In addition, protein adsorption and structural development at the interface were driven by hydrophobic interactions, while further rearrangement and polymerization were mediated by disulfide bonds. Furthermore, the stability and particle size distribution of the emulsion also supported the results. This study provided a theoretical basis for the behavior of BBHH emulsion formation, which expanded valuable insights into the mechanisms by which liquid food emulsification systems mediated by animal-derived proteins and how they behave under a variety of external conditions.
研究领域:
食品科学
·
生物化学
✓ 已验证
产品关联
DOI
PubMed
高影响因子
Marine Drugs
·
2022
·Vol. 20
·期 1
·48
·
IF 6.085
Jian Li,Jun-Hui Cheng,Zhao-Jie Teng,Xia Zhang,Xiu-Lan Chen,Mei-Ling Sun,Jing-Ping Wang,Yu-Zhong Zhang,Jun-Mei Ding,Xin-Min Tian,Xi-Ying Zhang
Although the S8 family in the MEROPS database contains many peptidases, only a few S8 peptidases have been applied in the preparation of bioactive oligopeptides. Bovine bone collagen is a good source for preparing collagen oligopeptides, but has been so far rarely applied in collagen peptide preparation. Here, we characterized a novel S8 gelatinase, Aa2_1884, from marine bacteriumFlocculibacter collagenilyticusSM1988T, and evaluated its potential application in the preparation of collagen oligopeptides from bovine bone collagen. Aa2_1884 is a multimodular S8 peptidase with a distinct domain architecture from other reported peptidases. The recombinant Aa2_1884 over-expressed inEscherichia colishowed high activity toward gelatin and denatured collagens, but no activity toward natural collagens, indicating that Aa2_1884 is a gelatinase. To evaluate the potential of Aa2_1884 in the preparation of collagen oligopeptides from bovine bone collagen, three enzymatic hydrolysis parameters, hydrolysis temperature, hydrolysis time and enzyme-substrate ratio (E/S), were optimized by single factor experiments, and the optimal hydrolysis conditions were determined to be reaction at 60 ℃ for 3 h with an E/S of 400 U/g. Under these conditions, the hydrolysis efficiency of bovine bone collagen by Aa2_1884 reached 95.3%. The resultant hydrolysate contained 97.8% peptides, in which peptides with a molecular weight lower than 1000 Da and 500 Da accounted for 55.1% and 39.5%, respectively, indicating that the hydrolysate was rich in oligopeptides. These results indicate that Aa2_1884 likely has a promising potential application in the preparation of collagen oligopeptide-rich hydrolysate from bovine bone collagen, which may provide a feasible way for the high-value utilization of bovine bone collagen.Keywords:peptidase;the MEROPS S8 family;bovine bone collagen;oligopeptides;hydrolysate
研究领域:
生物化学
·
酶学
·
食品科学
✓ 已验证
产品关联
DOI
PubMed
高影响因子
JOURNAL OF WUHAN UNIVERSITY OF TECHNOLOGY-MATERIALS SCIENCE EDITION
·
2019
·Vol. 34
·期 1
·230-235
·
IF 0.605
Liu Kang,Zhang Xianglin,Zhou Kui,Shi Lei,Chen Zhichao,Li Wenchao,Chen Penghua
The bovine hydroxyapatite (BHA) was applied to prepare biological tissue engineering scaffolds by the method of extrusion freeforming. To achieve this goal, BHA were added to sodium alginate (SA) solution to form a slurry system in appropriate proportion. The resulting mixtures were fabricated to be a kind of controllable and porous scaffolds followed with cross-linking in 5% calcium chloride (CaCl 2 ) solution for 24 h. After that, the scaffolds were sintered in air at 1 000, 1 100, 1 200 and 1 300 °C for 5 h. Scanning electron microscopy (SEM) and X-ray diffraction (XRD) studies were performed on the scaffolds to analyze its microstructure and constituent. To explore the effect of sintering temperature on scaffolds, the compressive strength, volume shrinkage and water absorptivity of BHA-SA composite scaffolds after sintering were investigated. The research tests indicated the feasibility of applying BHA powder to 3D printing. Besides, the scaffolds sintered in a respectively lower temperature possess much more pores and performed higher water absorptivity, which means better cellular affinity. And scaffolds sintered between 1 100 and 1 200 °C presents higher compressive strength.
研究领域:
生物材料学
·
组织工程学
✓ 已验证
产品关联
DOI
高影响因子
Marine Drugs
·
2021
·Vol. 19
·期 12
·676
·
IF 5.118
Jun-Hui Cheng,Xiao-Yu Zhang,Zhen Wang,Xia Zhang,Shi-Cheng Liu,Xiao-Yan Song,Yu-Zhong Zhang,Jun-Mei Ding,Xiu-Lan Chen,Fei Xu
Bovine bone is rich in collagen and is a good material for collagen peptide preparation. Although thermolysin-like proteases (TLPs) have been applied in different fields, the potential of TLPs in preparing bioactive collagen peptides has rarely been evaluated. Here, we characterized a thermophilic TLP, A69, from a hydrothermal bacteriumAnoxybacillus caldiproteolyticus1A02591, and evaluated its potential in preparing bioactive collagen peptides. A69 showed the highest activity at 60 °C and pH 7.0. We optimized the conditions for bovine bone collagen hydrolysis and set up a process with high hydrolysis efficiency (99.4%) to prepare bovine bone collagen peptides, in which bovine bone collagen was hydrolyzed at 60 °C for 2 h with an enzyme–substrate ratio of 25 U/g. The hydrolysate contained 96.5% peptides that have a broad molecular weight distribution below 10000 Da. The hydrolysate showed good moisture-retention ability and a high hydroxyl radical (•OH) scavenging ratio of 73.2%, suggesting that the prepared collagen peptides have good antioxidative activity. Altogether, these results indicate that the thermophilic TLP A69 has promising potential in the preparation of bioactive collagen peptides, which may have potentials in cosmetics, food and pharmaceutical industries. This study lays a foundation for the high-valued utilization of bovine bone collagen.Keywords:thermolysin-like protease;bovine bone collagen;collagen peptides;collagen peptide preparation;bioactivity
研究领域:
生物化学
·
食品科学
·
药学
·
化妆品
✓ 已验证
产品关联
DOI
PubMed
高影响因子
LWT-FOOD SCIENCE AND TECHNOLOGY
·
2022
·
IF 6.056
Jiamin Xu,Lili Yang,Yinghua Nie,Mengyang Yang,Wenjuan Wu,Zhengquan Wang,Xichang Wang,Jian Zhong
Molecular modification has attracted many attentions in the field of gelatin science. In this work, a transglutaminase (TG) modification method was developed and applied to modify bovine bone gelatin, porcine skin gelatin, and cold-water fish skin gelatin, and then the effect of TG crosslinking on the structural, physicochemical, functional, and emulsion stabilization properties of three types of gelatins were explored and compared. The results demonstrated that TG modification increased the nanoparticle formation behaviors and change the physicochemical and functional properties of three types of gelatins. Further, TG-modified aquatic gelatin showed comparable foaming properties (147% ± 6% for foaming capability and 55% ± 4% for foam stability) and higher emulsifying properties (18 ± 1 m 2 /g for emulsion activity index and 142 ± 11 min for emulsion stability index) to unmodified mammalian gelatins. In addition, TG-modified gelatins decreased the droplet sizes and increased creaming stability of fish oil-loaded emulsions compared with unmodified gelatins. All these results suggested TG modification was an efficient molecular modification method for gelatins. Moreover, TG-modified aquatic gelatin could be potential mammalian gelatin replacer. This work could provide useful information to understand the relationship among animal sources, tissue sources, extraction methods, amino acid compositions, molecular modification, molecular structure, physicochemical properties, functional properties, and emulsification stability of gelatins.
研究领域:
食品科学
·
化学
·
生物技术
✓ 已验证
DOI
高影响因子
Tissue Engineering Part A
·
2019
·
IF 3.616
Qing Li,Xiongxin Lei,Xiaofei Wang,Zhigang Cai,Peijun Lyu,Guifeng Zhang
Three-dimensional (3D) printing provides a novel approach to repair bone defects using customized biomimetic tissue scaffolds. To make a bone substitute closest to natural bone structure and composition, two different types of hydroxyapatite, Nano hydroxyapatite (nHA) and deproteinized bovine bone (DBB), were dispersed into collagen (CoL) to prepare the bioink for 3D printing. In doing so, a porous architecture was manufactured with 3D printing technology. The physical and chemical properties of the materials were evaluated, including biocompatibility and effect on the osteogenic differentiation of the human bone marrow-derived mesenchymal stem cells (hBMSCs). The XPS, XRD, FTIR, and the mechanical analysis of the material indicated that the two HA were consistent in their elements, but different in their chemical bonds and crystal phases. The SEM results showed the different surface morphologies of the HA crystals as well as the scaffolds, which would be the main factors affecting the internal porous structure of the scaffold. There were no differences between the two composite scaffolds in cell proliferations. FITC-phalloidin/vinculin/DAPI staining indicated that hBMSCs can adhere well to the 3D-printed surfaces. Alkaline phosphatase (ALP) staining reflected ALP expressed on both of the osteogenic-induction medium (OM) group, but not on proliferation medium (PM) group. The real-time polymerase chain reaction results showed the expression levels of osteogenesis-related genes RUNX2, SOX9, OCN, and COL1A1 in OM group were significantly increased after 7 days compared with the PM group (p < 0.01). The expression of SOX9, OCN, and COL1A1 in nHA/CoL scaffolds was higher than that in CoL scaffolds (p < 0.05). The expression of OCN and COLIA1 in DBB/CoL scaffolds was higher than that in CoL scaffolds (p < 0.05). In conclusion, the physicochemical and biological properties of 3D bioprinted scaffolds consisting of nHA/CoL or DBB/CoL would be well suited for the scaffolds to being a porous customized bone substitute, 3D printing scaffolds would be a prospective candidate for clinical application in future.Impact StatementBone loss due to trauma, inflammation, and surgical processes has posed great difficulty in the aesthetic reconstruction of a functional alveolar bone. Tissue engineering and biomaterials, which can promote alveolar bone regeneration, have become a popular focus of current studies. Three-dimensional (3D) printing provides a novel approach to repair bone defects using customized biomimetic tissue scaffolds. Nano hydroxyapatite (nHA) and deproteinized bovine bone (DBB) are two materials mainly used in clinical practice, particularly DBB are widely used in dentistry and craniomaxillofacial orthosis because of the porosity characteristic. To make a bone substitute closest to natural bone structure and composition, nHA and DBB were dispersed into collagen (CoL) to prepare the bioink for 3D printing. The physicochemical and biological properties between the two 3D printing scaffolds were compared. Both nHA/CoL and DBB/CoL 3D printing scaffold would be promising candidate for the clinical applications in the future.
研究领域:
组织工程
·
生物材料
·
再生医学
·
干细胞研究
·
生物医学工程
✓ 已验证
DOI
PubMed
高影响因子
FOOD CHEMISTRY
·
2021
·
IF 7.514
Ting Zhang,Jiamin Xu,Shudan Huang,Ningping Tao,Xichang Wang,Jian Zhong
In this work, ring-like anhydrides (C4, C5, and C6) with different sizes and succinic anhydrides (C4, C10, C12, C14, and C16) with different side chain lengths were used to modify bovine bone gelatin (BBG) and cold-water fish skin gelatin (CFG), and the effect of acylated gelatins on fish oil-loaded emulsions stability was explored. The results showed that the degree of N -acylation decreased with increased ring sizes or side chain lengths, and the surface hydrophobicity of acylated gelatins increased with increased anhydride carbon numbers. Acylated CFGs had higher droplet stability and lower liquid-gel transition time than acylated BBGs. Only BBG-C12 had a slight increase on the creaming stability among these acylated gelatins. These results demonstrated that the gelatins could be modified by all the anhydrides and their emulsion stabilization ability was dependent on the gelatin type and anhydride structure. The results could be beneficial for protein-based emulsifier development and application.
研究领域:
食品科学
·
化学
·
材料科学
✓ 已验证
产品关联
DOI
PubMed
高影响因子
JOURNAL OF BIOMEDICAL MATERIALS RESEARCH PART A
·
2017
·Vol. 106
·期 5
·1236-1246
·
IF 3.076
Miusi Shi,Can Wang,Yulan Wang,Cuizhu Tang,Richard J. Miron,Yufeng Zhang
Bone grafts are widely used in bone regeneration to increase the speed and quality of new bone formation. While they are routinely characterized based on their biocompatible and bioactive properties, they also exert a profound impact on host immune responses, which in turn can display a significant effect on the healing and repair process. In this study, we investigated the role of macrophage behavior on deproteinized bovine bone matrix (DBBM, BioOss) to investigate their impact on creating either a pro- or anti-inflammatory microenvironment for tissue integration. RT-PCR and immunofluorescence staining results demonstrated the ability for RAW 264.7 cells to polarize toward M2 wound-healing macrophages in response to DBBM and positive control (IL-4). Interestingly, significantly higher expression of interleukin-10 and higher number of multinucleated giant cells (MNGCs) was observed in the DBBM group. Thereafter, conditioned media (CM) from macrophages cultured with DBBM seeded with MC3T3-E1 cells demonstrated a marked increase in osteoblast differentiation. Noteworthy, this effect was reversed by blocking IL10 with addition of IL10 antibody to CM from the DBBM macrophages. Furthermore, the use of dendritic cell specific transmembrane protein (DC-STAMP)-knockout to inhibit MNGC formation in the DBBM group resulted in a significant reduction in osteoblast differentiation, indication a pivotal role for MNGCs in biomaterials-induced osteogenesis. The results from this study indicate convincingly that the immune response of macrophages towards DBBM has a potent effect on osteoblast differentiation. Furthermore, DBBM promoted macrophage fusion and polarization towards an M2 wound-healing phenotype, further created a microenvironment favoring biomaterial-induced osteogenesis. © 2018 Wiley Periodicals, Inc. J Biomed Mater Res Part A: 106A: 1236–1246, 2018.
研究领域:
生物材料
·
免疫学
·
组织工程
·
骨科
✓ 已验证
DOI
PubMed
高影响因子
危险品化学品经营许可证（带存储）