CARBOHYDRATE POLYMERS
·
2019
·
IF 6.044
Xiaoliang Qi,Zhipeng Li,Liangliang Shen,Tao Qin,Yuna Qian,Shengzhe Zhao,Minchao Liu,Qiankun Zeng,Jianliang Shen
Wastewater treatment materials that combine high decontamination performance, ease of use and economic production are highly desirable for practical applications. Herein, we fabricated a low-cost and recyclable bio-adsorbent based on a microbial polysaccharide (salecan) for efficient removal of methyl violet (MV) from wastewater. The success fabrication and the properties (such as thermal stability, microarchitecture, mechanical strength and water uptake) of the adsorbent had been investigated, and the hydrogels were found to have tunable properties by simple adjusting the salecan dose in hydrogel composition. Adsorption data displayed that the adsorption of MV followed the pseudo second-order kinetic model (R 2 = 0.99015) and Freundlich isotherm model (R 2 = 0.99221) with a maximum adsorption capacity of 178.9 mg/g. Moreover, salecan-based hydrogels showed a good reversibility in adsorption–desorption cycles. These features indicate that salecan-based bio-adsorbent may be a promising device for dye removal from dyeing waste water.
研究领域:
环境科学
·
生物材料学
✓ 已验证
产品关联
DOI
PubMed
高影响因子
ENVIRONMENTAL TECHNOLOGY
·
2022
·
IF 3.475
Hua Lin,Kaiwei Chen,Linlin Du,Peng Gao,Junli Zheng,Yuanli Liu,Lili Ma
As an important biomass resource, agricultural waste is of great significance to improve the application value. In this study, the yellow passion fruit peel (Y-PFP) was used as a biosorbent to remove cationic dyes (methylene blue (MB) and methyl violet (MV)) by the simple treatment process. And the effects of pH, contact time, initial dye concentration, ionic strength, and temperature on the adsorption performance of Y-PFP were studied. The adsorption process was consistent with the pseudo-second-order kinetic model and Langmuir isotherm. What’s more, the maximum adsorption capacity for MB and MV was 324.7 and 485.4 mg·g−1, respectively. And Y-PFP still exhibited high removal efficiency after five desorption–adsorption cycles. Thus, Y-PFP had highly valuable for the removal of cationic dyes from wastewater with a simple preparation process, low cost, excellent adsorption capacity and selectivity.
研究领域:
环境科学
·
生物工程
✓ 已验证
产品关联
DOI
PubMed
高影响因子
ACS Applied Polymer Materials
·
2024
·
IF 4.4
Qianlan Huang,Jialing Li,Zhiyuan Peng
An active hydroxymethyl group was introduced to the phenolic ring structure of tannin, and then the polyphenol network from hydroxymethyl tannin was immobilized on the surface of the filter paper (FP) by the reaction between hydroxymethyl tannin and cellulose of FP. Due to the introduction of the polyphenol structure on the surface of the FP, the ultraviolet absorption of the FP was broadened, the thermal stability of the FP was increased, and the FP was endowed with the antibacterial properties. The inhibition efficiency for Escherichia coli and Staphylococcus aureus was 82.3 and 80.1%, respectively. The FP-immobilized polyphenol network of tannin had good adsorption performance for methyl violet (MV), and the maximum adsorption capacity for MV was 131.5 mg·g–1. The adsorption efficiency could reach more than 98% when the initial mass concentration of MV was lower than 50 mg·L–1. The adsorption process conformed to the Langmuir isothermal adsorption model and quasi-secondary adsorption kinetic model. The FP-immobilized polyphenol network of tannin has good adsorption repeatability, and the preparation method is facile, green, and ecofriendly, which can be considered as a new potential adsorbent for dye wastewater.
研究领域:
材料科学
·
环境科学
·
生物学
✓ 已验证
产品关联
DOI
高影响因子
Journal of Inorganic and Organometallic Polymers and Materials
·
2024
·
IF 3.9
Agha Hasan M.,Abdulhameed Ahmed Saud,Jawad Ali H.,Khadiran Tumirah,ALOthman Zeid A.,Wilson Lee D.
A biopolymer matrix of chitosan (CTS) and algae (AGA) was chemically modified with a natural genipin (GEN) cross-linker agent via hydrothermal process. The resulting green adsorbent (CTS-GEN/AGA) was evaluated for removal of the cationic dye (methyl violet, MV) from aqueous media. The optimization of MV adsorption onto CTS-GEN/AGA was performed using the Box–Behnken design (BBD), considering the variables of adsorbent dose (0.02–0.1 g/100 mL), pH (4–10), and time (20–300 min). The CTS-GEN/AGA demonstrated the highest MV removal (76.49%) for optimal operational parameters: CTS-GEN/AGA dosage (0.0938 g/100 mL), pH (8.4), and contact time (215.3 min). The adsorption isotherm analysis revealed a close fit between the experimental data of MV adsorption and the Temkin model. Furthermore, the adsorption kinetics are well-described by the pseudo-second-order model. The maximum adsorption capacity of CTS-GEN/AGA was 71.9 mg/g at 25 °C. The probable adsorption mechanism can be assigned to H-bonding, electrostatic forces, and n–π stacking interactions. These findings highlight the potential of CTS-GEN/AGA as an effective adsorbent for treatment of wastewater for the removal of organic dyes.
研究领域:
环境科学
·
材料科学
·
生物化学
✓ 已验证
产品关联
DOI
高影响因子
Desalination and Water Treatment
·
2024
·
IF 1
Lincai Peng,Jing Gao,Shun Yao,Xianqiu Lan,Huaiping Li,Hang Song
ABSTRACT As a common agriculture waste as well as available biomass resource from ginkgo tree, ginkgo leaves were used as adsorbent to remove two models of cationic dyes methyl violet (MV) and malachite green (MG) after adequate modification. As the result, hydroxylated magnetic ginkgo leaf powder and carboxylated magnetic ginkgo leaf powder were obtained and characterized, respectively, which had the potential to be an environmentally friendly and economically effective biosorbents for the adsorption of dyes. These new biosorbents exhibited high adsorption capacity for dyes, with the maximum adsorption capacity of 450 mg g –1 for MV and 231 mg g –1 for MG. Further investigation confirmed that these adsorption processes were fitted with pseudo-second-order and Langmuir isothermal model. Moreover, these adsorbents with remarkable magnetism could be easily and rapidly recovered by external magnet after their use. The study demonstrated that the promising and reliable modified biosorbents were very suitable for removal of cationic dyes with high concentration at lower cost.
研究领域:
环境科学
·
生物技术
✓ 已验证
DOI
高影响因子
ChemistrySelect
·
2024
·Vol. 9
·期 33
·e202401481
·
IF 1.9
Mengyao Liu,Yuling Huang,Panpan Xu,Tingting Xu,Yinggui Zhu
Graphical In this paper, We developed a novel ECL sensor of the 6-MC/S 2 O 8 2− system by using 2-NSA as co-reaction accelerator. 2-NSA was first proposed as co-reaction accelerator, promoting the generation of additional oxidant SO 4 − from S 2 O 8 2− , thus amplifying the ECL signal. Moreover, this research provides a highly sensitive platform for the detection of MV. In this paper, the novel ECL sensor of the 6-methoxychromone (6-MC)/S 2 O 8 2− system was designed by using 2-naphthalene sulfonic acid (2-NSA) as a co-reaction accelerator. Fluorescence, ECL spectrum, and cyclic voltammetry (CV) were used to explore extensively the ECL mechanism of the system. It is worth pointing out that 2-naphthalene sulfonic acid (2-NSA) was first proposed as a co-reaction accelerator, reacting with the coreactant K 2 S 2 O 8 rather than the luminophore, promoting the generation of additional oxidant SO 4 − from S 2 O 8 2− , thus amplifying the ECL signal. Furthermore, under the optimal experimental conditions, the high sensitivity of the 2-naphthalene sulfonic acid (2-NSA)+6-methoxychromone (6-MC)/S 2 O 8 2− system was realized for the detection of methyl violet (MV) in the linear range of 10 −8 ~10 −2 M, with a detection limit of 5.14×10 −10 M. In addition, this find offers some guidance for further developing co-reaction accelerators with excellent performance in the future.
研究领域:
分析化学
·
生物传感
✓ 已验证
产品关联
DOI
高影响因子
ELECTROCHIMICA ACTA
·
2022
·
IF 7.336
Jiaqi Xu,Zongcai Deng,Bo Wu,Meijin Lin,Dongyang Chen
Organic polymers containing redox-active moieties have attracted increasing attention as electrode materials for high-performance rechargeable batteries due to their sustainability, flexibility, environmentally benign, and high stability. Herein, viologen functionalized fluorene-containing poly(arylene ether ketone)s (MV-FPAEKs) were synthesized by polycondensation , bromination, and quaternization in sequence. 1 H NMR was used to monitor the degree of functionalization (DF), which increased with the increasing of the molar ratio of the bromination agent. The MV-FPAEK-96 with a DF of 96% for viologen was used as the active material for polymer cathode. The theoretical specific capacity was calculated to be 87.6 mAh g −1 based on the dual electron transfer per viologen unit. It had been found that the MV-FPAEK-96 battery delivered a discharge specific capacity of 87.1 mAh g −1 at a current rate of 0.1 C, and maintained 32.1 mAh g −1 after 100 galvanostatic cycles. In contrast, the small molecule of dimethyl viologen was highly soluble in the electrolyte, and the corresponding capacity decreased to negligible values after only 20 cycles. Therefore, the attachment of viologen to polymeric backbones is an effective strategy to increase the stability in electrolyte while maintaining the rechargeability, and the MV-FPAEK-96 is a promising redox-active candidate for polymer batteries.
研究领域:
材料科学
·
电化学
✓ 已验证
DOI
高影响因子
Journal of Environmental Sciences
·
2015
·
IF 2.002
Guangyan Tian,Wenbo Wang,Yuru Kang,Aiqin Wang
Herein, palygorskite (PAL) was activated via a simple hydrothermal process in the presence of ammonium sulfide, and the effects of activation on the microstructure, physico-chemical feature and adsorption behaviors of PAL were intensively investigated. The hydrothermal process evidently improved the dispersion of PAL crystal bundles, increased surface negative charges and built more active –Si–O − groups served as the new “adsorption sites”. The adsorption property of the activated PAL for Methyl Violet (MV) was systematically investigated by optimizing the adsorption variables, including pH, ionic strength, contact time and initial MV concentration . The activated PAL exhibited a superior adsorption capability to the raw PAL for the removal of MV (from 156.05 to 218.11 mg/g). The kinetics for MV adsorption followed pseudo second-order kinetic models, while the isotherm and thermodynamics results showed that the adsorption pattern well followed the Langmuir model. The structure analysis of PAL before and after adsorption demonstrated that electrostatic interaction and chemical association of –X–O − are the prominent driving forces for the adsorption process.
研究领域:
环境科学
·
材料科学
✓ 已验证
产品关联
DOI
PubMed
高影响因子
JOURNAL OF APPLIED POLYMER SCIENCE
·
2015
·Vol. 133
·期 5
·
IF 1.768
Hao Ying,Guijin He,Lifeng Zhang,Qunfang Lei,Yongsheng Guo,Wenjun Fang
Hydrogels were synthesized from hyperbranched polyglycerol (HPG) and acrylic acid through free-radical polymerization with HPG as the crosslinker. The HPG/poly(acrylic acid) (PAA) hydrogel could absorb cationic dyes in aqueous solutions because of the existence of a porous structure and the large numbers of hydroxyl and carboxylic groups. With methyl violet chosen as a model compound, the HPG/PAA hydrogel reached a maximum adsorption of 394.12 mg/g at a feed concentration of 1 g/L. The highest removal ratio of 98.33% was observed at a feed concentration of 50 mg/L. The effects of the pH, contact time, and feed concentration on the dye adsorption were investigated. The dye adsorption data fit well with the pseudo-second-order and Langmuir models. We believe that the HPG/PAA hydrogels could perform well in appropriate applications in the removal of cationic dyes from aqueous solutions because of their high adsorption capacity and environmental friendliness. © 2015 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2016 , 133 , 42951.
研究领域:
材料科学
·
环境科学
✓ 已验证
产品关联
DOI
高影响因子
SUPRAMOLECULAR CHEMISTRY
·
2021
·
IF 1.688
Kai Liu,Huijun Liu,Liuxing Li,Wei Li,Juan Liu,Ting Tang
β-cyclodextrin(β-CD) was immobilised onto mesoporous silica using 1,1′-carbonyldiimidazole and tetraethyl orthosilicate as raw materials to construct adsorbent in dye wastewater treatment. The mesoporous structure of β-CD@SiO2-1 was characterised by Fourier transform infrared spectroscopy (FT-IR), X-ray diffraction (XRD), specific surface area measurement (BET), thermogravimetric (TG) and scanning electron microscopy (SEM). The adsorption experiments were studied by response surface method (RSM) to optimise various parameters such as initial concentration, contact time and adsorbent dosage on the adsorption property of β-CD@SiO2-1 to methyl violet. The optimum process conditions were initial concentration 34 mg/L, contact time 13 h and adsorbent dose 5 mg. The adsorption rates correspond to the pseudo-second-order kinetic model. The adsorption isotherm was suited to the Langmuir isotherm model. The thermodynamic parameters (ΔG°, ΔH°, ΔS°) were obtained. As a result, it was found that the adsorption process was exothermic and spontaneous.
研究领域:
环境科学
·
材料科学
✓ 已验证
DOI
高影响因子
INTERNATIONAL JOURNAL OF ENVIRONMENTAL ANALYTICAL CHEMISTRY
·
2024
·
IF 2.3
Muna Sarhan Sando,Ahlam M. Farhan,Lee D. Wilson,Ali H. Jawad
Herein, a biocomposite of crosslinked chitosan polyethylene glycol diglycidyl ether (CS-PEDGE), montmorillonite (MMT), and food-grade algae (FGA) was successfully prepared by a hydrothermal technique. The resulting absorbent (CS-PEDGE/FGA/MMT) was assessed for its adsorption property with methyl violet 2B (MV 2B) a toxic cationic dye. The physicochemical properties of CS-EDGE/FGA/MMT were assessed via various analytical techniques, including BET, Elemental analysis, pHpzc, and spectroscopy (FTIR, XRD, SEM-EDX). The influence of three adsorption variables, namely adsorbent dose (A: 0.02–0.1 g/100 mL), solution pH (B: 4–10), and contact time (C: 10–420 min) on the rate of MV 2B dye removal was examined using the Box-Behnken design (RSM-BBD). The findings from the equilibrium isotherm and kinetic analyses suggest that the MV 2B dye adsorption onto the biocomposite surface follow the Freundlich model and pseudo-second-order kinetic models. The biocomposite adsorbent exhibits a maximum dye adsorption capacity (qmax) of 94.2 mg/g. The proposed MV 2B dye adsorption mechanism involves hydrogen bonding, n-π stacking, and electrostatic forces. This research demonstrates the unique structure and outstanding adsorption properties of CS-EDGE/FGA/MMT, which offers a viable solution for removal of detrimental MV 2B dyes from aqueous media.
研究领域:
环境科学
·
材料科学
·
化学工程
✓ 已验证
DOI
高影响因子
JOURNAL OF MATERIALS SCIENCE-MATERIALS IN ELECTRONICS
·
2017
·Vol. 29
·期 3
·2282-2290
·
IF 2.019
Zhao Gao-yu,Yang Shao-wei,Jiang Lin,Zhang Hong-mei
Novel Ag 10 Si 4 O 13 /N–CeO 2 composite photocatalysts were synthesized by a facile one-pot method. XRD, SEM, EDS, and UV–Vis DRS were employed to characterize the structures of the samples. Moreover, the degradation activity of methyl violet (MV) was used to measure the photocatalytic performances of Ag 10 Si 4 O 13 , N–CeO 2 , and the Ag 10 Si 4 O 13 /N–CeO 2 composites. It was found that ASO-10 (the Ag 10 Si 4 O 13 /N–CeO 2 composite with 10 mg N–CeO 2 ) showed the highest photocatalytic activity in the degradation of MV, and the enhanced photocatalytic performance is attributed to an improvement in the separation efficiency of photoproduced electron–hole pairs. Effects of operational parameters, such as initial pH, catalyst dosage, initial dye concentration, anions and cations, have also been considered for better practical applications. In addition, the photocatalytic mechanism of the Ag 10 Si 4 O 13 /N–CeO 2 composites is also proposed.
研究领域:
材料科学
·
环境科学
✓ 已验证
产品关联
DOI
高影响因子
危险品化学品经营许可证（带存储）