TALANTA
·
2023
·
IF 6.1
Rui Wang,Chunlan Liu,Yong Wei,Ze Ran,Tianci Jiang,Chunbiao Liu,Chen Shi,Zhuo Ren,Xingkai Wang,Zhihai Liu,Yu Zhang
The concentration of tumor markers is low, which needs a highly sensitive, stable and fast detection method. In this paper, we proposed and demonstrated a U-shape fiber SPR biosensor sensitized by MOFs materials. The surface of the U-shape SPR sensor was modified with MOFs materials to enhance the sensitivity, and the nucleic acid aptamer was immobilized on the sensor surface because of the biocompatibility of MOFs materials. By the high specificity of the nucleic acid aptamer, the MUC1 protein was recognized and detected. The testing results indicate that the sensor has a logarithmic linear response in the MUC1 protein concentration detection range of 1 pg/ml-100 μg/ml, its sensitivity and detection limit are 5.33 nm/log(μg/ml) and 0.16 pg/ml respectively. After being sensitized by MOFs, the detection sensitivity of the sensor can be increased by 1.62 times，the LOD can be decreased by 0.75 times. The sensor has high sensitivity and specificity, which has broad application prospects in clinical detection of tumor markers.
研究领域:
生物医学工程
·
肿瘤标志物检测
✓ 已验证
产品关联
DOI
PubMed
高影响因子
CHEMICAL ENGINEERING JOURNAL
·
2020
·
IF 10.652
Zhongyu Yang,Long Zhang,Yiyuan Zhang,Mengyuan Bai,Yunchuan Zhang,Zihan Yue,Erhong Duan
Pyrolysis process of metal-organic frameworks (MOFs) was analyzed by thermal analysis kinetics for the study of the synthesis of MOFs-based carbon materials with high adsorption performance. The process was studied based on the thermogravimetric mass spectrometry (TG-MS), through which the gas products of the pyrolysis process were detected. The HKUST-1 and MIL-101 were prepared by solvothermal method and characterized by XRD, BET, SEM and TEM. The characterization results showed that HKUST-1 and MIL-101 have been successfully prepared with cubic octahedral morphology and specific surface areas up to 1477.50 m 2 /g and 2239.88 m 2 /g, respectively. The data of TG-DTG showed that the pyrolysis of HKUST-1 and MIL-101 could be divided into three stages and seven stages, respectively. The kinetic triplets of different pyrolysis stages were calculated by iso-conversional methods, and the gas products decomposed were analyzed, through which the pyrolysis mechanism of MOFs was inferred. The first pyrolysis stages of HKUST-1 and MIL-101 were both dehydration stages, the E values of both were less than 100 kJ/mol, and the pyrolysis mechanism of both two materials at this stage were the chemical reaction mechanism. The average apparent activation energy of the main pyrolysis carbonization stages of both was about 180 kJ/mol, and both followed the random nucleation and subsequent growth mechanism, indicating that there were some uniformities between the two materials in the main pyrolysis stage. The main gas products in this stage were CO, CO 2 and benzene. The apparent activation energy of the final deep carbonization stage were 564.36 and 387.60 kJ/mol, respectively, and mechanisms followed were chemical reactions and three-dimensional diffusion mechanisms, meaning that there were some differences between the two materials in the deepening stage.
研究领域:
材料科学
·
化学工程
✓ 已验证
DOI
高影响因子
CATALYSIS LETTERS
·
2021
·Vol. 152
·期 8
·2375-2385
·
IF 3.186
Li Ying,Wang Qian,Ding Zhu,Wan Dong,Nie Xuetong,Zhong Chongli
Abstract A facile one-step route was presented to prepared NH 2 -MIL-88B(Fe) and Fe 3 O 4 modified reduced graphene oxide nanoparticles (NH 2 -MIL-88B(Fe)@MRGO) as mimic enzymes. The as-prepared NH 2 -MIL-88B(Fe)@MRGO exhibits a higher affinity for hydrogen peroxide and thus possessed a prominent peroxidase-mimic activity. Under the most favorable conditions, the hybrid nanomaterials with high catalytic velocity (2.57 × 10 −7 M s −1 ) and affinity (Km = 0.0091 mM) for substrates of H 2 O 2 display a great glucose detection performance in the range of 20–800 μM with a Limit of detection (LOD) of 3.16 μM (S/N = 3). Graphic Abstract Favorable mimic enzymes catalysis is achieved on NH 2 -MIL-88B(Fe) and Fe 3 O 4 modified reduced graphene oxide nanoparticles (NH 2 -MIL-88B(Fe)@MRGO) for glucose detection.
研究领域:
生物化学
·
材料科学
·
分析化学
✓ 已验证
产品关联
DOI
高影响因子
Journal of Energy Storage
·
2023
·
IF 9.4
Shengnan Lin,Tingan Zhang
With the upgrading of mobile and portable electronic devices, people have higher requirements for the performance of batteries , and anode materials, as one of the factors affecting the electrochemical performance of lithium ion storage, have become a hot spot of widespread concern. This paper illustrates a creative and effective strategy to synthesize four different NiCo-MOFs materials. After studying their respective unique structural features, it was found that, unlike the topologies of NiCo-PTA (terephthalic acid) and NiCo-H 3 BTC (trimesic acid), the substitution of Ni and Co for N occurred in NiCo-EDTA (ethylenediaminetetraacetic acid) and NiCo-BI (benzimidazole). Electrochemical studies show that NiCo-PTA, NiCo-EDTA, NiCo-H 3 BTC, and NiCo-BI all have high initial discharge specific capacities of 1770.41576.11905.1 and 1877.5 mAh/g at a current density of 100 mA/g. When NiCo-EDTA and NiCo-BI are cycled at a current density of 100 mA/g, the specific capacity decreases more slowly than NiCo-PTA and NiCo-H 3 BTC. Similarly, the capacity of NiCo-PTA and NiCo-H 3 BTC almost began to rise at the 70th cycle, the capacity of NiCo-BI began to rise at the 67th cycle, and NiCo-EDTA showed the slowest rise at the 78th cycle, they all showed excellent cycle performance.
研究领域:
材料科学
·
能源存储与转换
✓ 已验证
产品关联
DOI
高影响因子
JOURNAL OF MATERIALS RESEARCH
·
2021
·Vol. 36
·期 14
·2961-2972
·
IF 3.089
Zhu Lijun,Zhu Xinxin,Zhang Chao,Huo Tian,Hou Xinlan,Guo Dandan,Zhang Huiming,Xia Daohong
The zirconium-based porphyrin MOFs sensitized TiO 2 (PCN224–TiO 2 ) was synthesized in situ by self-assembly of porphyrin, ZrCl 4 with nano TiO 2 . The composite catalyst was determined by detailed structural and photoelectrochemical characterization. The UV–Vis absorption and fluorescence spectrum confirm that PCN224 and TiO 2 are coupled. The PCN224–TiO 2 had significant absorption of visible light and the PCN224–TiO 2 had the largest photo-generated current, which proved the porphyrin MOFs material has good internal conductivity and has a close combination with TiO 2 . Compared with carboxyphenyl porphyrin sensitized TiO 2 (HTCPP–TiO 2 ), mixture of TCPP and TiO 2 (TCPP/TiO 2 ) and PCN224, the PCN224–TiO 2 showed better removal performance of methylene blue under visible light. Under low-power xenon lamp irradiation, the removal rate of PCN224–TiO 2 (1:3) on methylene blue reached 93.2% in 4 h. And PCN224–TiO 2 had stable cycling catalytic performance. The PCN224–TiO 2 promoted the degradation process by strengthening the adsorption of organic pollutants, thus improving the removal performance. Graphic abstract
研究领域:
材料科学
·
环境科学
✓ 已验证
产品关联
DOI
高影响因子
SN Applied Sciences
·
2019
·Vol. 1
·期 7
·1-8
·
IF 0
Wen Qijuan,Sun Tanghao,Wang Qi,Huang Wenwen,Liu Yunchun
Stationary sorbents play a key role in the separation process. We present here a kind of unique separative material, called thiophilic affinity MOFs, as specific sorbent for the capture of compounds containing disulfide-bond. The sorbent was obtained through epoxide ring-opening reaction among MOF-5-NH 2 , tris(2,3-epoxypropyl) isocyanurate, and thiophilic reagents under mild reaction condition. The synthesized sorbent was characterized with X-ray diffraction, scanning electron microscope, transmission electron microscope, Fourier transform infrared, thermogravimetric analysis and N 2 absorption. The capillary electrophoresis experiments verified their high specific recognization and separation for disulfide bond-containing compounds.
研究领域:
材料科学
·
分析化学
·
生物化学
✓ 已验证
产品关联
DOI
CHEMICAL ENGINEERING JOURNAL
·
2024
·
IF 13.3
Xinqi Luan,Xuehui Jia,Syed Jalil Shah,Jingyu Bao,Shunxiang Qin,Ruimeng Wang,Jiguang Deng,Zhongxing Zhao,Zhenxia Zhao
Low adsorption efficiency and secondary pollution release pose a bottleneck for the efficient capture of radioactive iodine vapor during nuclear utilization via adsorption. In addition, the simultaneous adsorption of iodine vapor alongside other harmful vapors in complex systems has been rarely reported. In this work, an electron/H-donating defective pore construction strategy involving MIL-101 modification via amino acids (AAs) was proposed to enhance its simultaneous adsorption efficiency for iodine and formaldehyde vapors. These defective microenvironments possessed microporous property with 11.3 Å, which not only formed strong affinity for I 2 molecules itself but also enhanced its adsorption interaction towards polyiodide anion (I 3 - and I 5 - ) through electron donation of AAs. Moreover, these adsorbed polyiodide anions and AAs-SL within the MOFs, resulting in multisite capture of FA via NH…O-H…I hydrogen bonding. The results revealed that AAs coordinated MIL-101 exhibited superior removal rate ( k 80% = 0.61–1.15 g g −1 h −1 ) for iodine vapor than that of the original MIL-101, which was 3.6–30.8 times higher that of state-of-the-art adsorbents under similar conditions. Notably, a high-capacity superior retention rate of 94.8 % was achieved for its I 2 adsorption after exposure to air for 7 days. After adsorption of iodine, AAs coordinated MIL-101 retained high FA adsorption capacity up to 9.7–12.9 mg/g, representing 75.1 %–87.7 % of the original AAs@MIL adsorption capacity for FA. This defective engineering strategy in MOFs supplied an efficient method for removing multiple harmful gases from the surrounding nuclear waste atmosphere.
研究领域:
环境科学
·
材料科学
✓ 已验证
产品关联
DOI
高影响因子
Surfaces and Interfaces
·
2024
·
IF 5.7
Ting Pan,Chuang Chen,Li Yu,Cong Yin,Mi Zhou,Huidong Qiu,Guoyuan Yuan,Wei Xiong,Xiaoqin Pu
In addressing the crucial need for separating cobalt ions from leachate solutions of spent ternary lithium batteries (TLBs), this study focuses on the development of an innovative molecular sieve (MS)-based MOFs material, MS-MIL-53(Al), synthesized by combining MS with 2,5-dihydroxyterephthalic acid. Since the powdered MS-MIL-53(Al) material presents a granular powdery form, which is difficult to recover during the adsorption process, electrospun nanofibers denoted as MS-MIL-53(Al)/PAN, were fabricated and functionalized with hydroxylamine hydrochloride to create MS-MIL-53(Al)/AOPAN. Static adsorption experiments conducted with MS-MIL-53(AL)/AOPAN as the adsorbent in cobalt-containing wastewater revealed a maximum adsorption content of 65.3 mg/g for Co(II). Moreover, the material exhibited a tensile strength at the breaking point of 0.077 kPa, indicating its excellent mechanical properties. The adsorption process followed pseudo-second-order kinetics and the Langmuir isotherm model, showcasing a spontaneous, endothermic monolayer chemical adsorption behavior. XPS analysis highlighted the influence of hydroxy and amidoxime functional groups on Co(II) adsorption. Notably, MS-MIL-53(Al)/AOPAN displayed exceptional stability, retaining over 90 % of its adsorption capacity after five cycles, demonstrating its potential for efficient Co(II) separation in wastewater treatment. This study is the first to synthesize MOFs material using MS as the base material, showing potential cost reduction and enhanced adsorption capabilities, with implications for advancing the innovative use of MOFs.
研究领域:
环境科学
·
材料科学
✓ 已验证
产品关联
DOI
高影响因子
Chemistry-An Asian Journal
·
2021
·Vol. 16
·期 22
·3743-3747
·
IF 4.568
Min-Jie Chen,Gang-Gang Chang,Li-Yan Chen,Ke-Xin Huang,Chun Pu,Dan Li,Yao Yao,Jia-Xin Li,Xiao-Yu Yang,Banglin Chen
Graphical The core-shell catalyst with surface wrinkles greatly improves the selectivity of tandem catalysis. Process intensification, targeting the maximization of spatial-temporal productivity utilizing minimum energy and resources has always been the constant trends especially in chemical industry. In this regard, tandem reactions that are able to perform a multi-step reaction in a single pot by eliminating costly separation steps have been viewed as a typical paradigm. However, a spatial isolation of varied active sites with a controlled manner in a single catalyst to avoid deactivation and work synergistically is a challenging problem yet sometimes being overlooked. In this work, a spatial base-metal core-shell structured catalyst with wrinkled surface was successfully fabricated by a direct homoepitaxial growth method in an acid/water system, which exhibited increased hydrophobicity, exposure of active sites and significantly improved product selectivity towards one-pot Knoevenagel condensation-hydrogenation tandem reaction compared with the uncoated catalyst. Meanwhile, the catalytic performance was largely retained and the structural stability was maintained even after successive 8 cycles, which shows great promise for industrial applications.
研究领域:
化学工程
·
材料科学
✓ 已验证
DOI
高影响因子
CHEMOSPHERE
·
2024
·
IF 8.1
Xinyue Feng,Haolin Shi,Wei Liu,Fangwei Ma,Pan Liu,Jiafeng Wan
This study demonstrated the design and fabrication of flower-like Ni/Mn-MOFs materials, and three-dimensional ultrathin flower-like Ni/Mn/MC microspheres were fabricated by embedding metal or metal oxide nanoparticles into a porous carbon skeleton via high-temperature pyrolysis at 600 °C and used for the electrocatalytic degradation of ceftriaxone sodium. This unique ultrathin porous flower-like structure can expose more active sites, provide rapid ion/electron transfer, and improve electrocatalytic activity. Meanwhile, the excellent electrical conductivity of the carbon skeleton, as well as the rational composition and synergistic effect of the two components, can promote the generation of active radicals (•OH and •O 2 − ) in the reaction system, which accelerates the electrochemical degradation process and improves the electrocatalytic degradation performance. The results showed that the Ni/Mn/MC-5:1 composite prepared when the molar ratio of Ni: Mn was 5:1 exhibited the best electrocatalytic degradation performance for the degradation of sodium ceftriaxone. The composites showed 98.2% degradation of ceftriaxone sodium in 120 min and maintained sound degradation after 20 cycles. Therefore, we concluded that this novel multicomponent composite has good electrocatalytic activity and stability for the degradation of antibiotic wastewater.
研究领域:
环境科学
·
材料科学
·
化学工程
✓ 已验证
产品关联
DOI
PubMed
高影响因子
SENSORS AND ACTUATORS B-CHEMICAL
·
2015
·
IF 4.097
Dongfang Wang,Yingchang Ke,Di Guo,Hongxu Guo,Jianhua Chen,Wen Weng
A metal-organic frameworks (MOFs), cauliflower-like MIL-100(Cr), has been facilely prepared through simple reflux method for the first time and characterized by XRD, FT-IR, SEM and XPS. The MOFs was found to be useful for the simultaneous and selective electrochemical detection of microgram Cd(II), Pb(II), Cu(II), and Hg(II) in aqueous solution. The detection was performed by the square wave anodic stripping voltammetry (SWASV). The MIL-100(Cr) modified electrode showed an excellent selectivity and stability for Cd 2+ , Pb 2+ , Cu 2+ , Hg 2+ determinations. The electrochemical properties and applications of the modified electrode were studied. Operational parameters such as pH, deposition potential and deposition time were optimized for the purpose of determination of traces of metal ions .
研究领域:
材料科学
·
分析化学
✓ 已验证
DOI
高影响因子
Catalysis Science & Technology
·
2020
·Vol. 10
·期 6
·1699-1707
·
IF 5.721
Yu-Ping Xu,Zhi-Qiao Wang,Hong-Zi Tan,Kai-Qiang Jing,Zhong-Ning Xu,Guo-Cong Guo
CO esterification to dimethyl carbonate (DMC) is an attractive route, although the catalyst is the main problem restricting the industrialization of this route. Supported palladium catalysts have been often used for this route. However, the effect of the support is not always clear. In this work, we firstly introduced three metal–organic frameworks (MOFs) materials as catalyst supports, namely UiO-66, MIL-101 and MOF-5, and studied the effect of Lewis acid sites in the MOFs supports on the catalytic activity and selectivity for CO esterification to DMC. Interestingly, the Pd(II)/UiO-66 catalyst exhibits superior catalytic performance to the other catalysts, with 87.9% CO conversion and 98.5% DMC selectivity due to the abundant Lewis acid sites in UiO-66. It was proven that UiO-66 with more defects would have a large number of Lewis acid sites, and the catalytic performance was positively correlated with the number of Lewis acid sites in MOFs supports, which can be demonstrated by characterization by NH3-TPD, pyridine-IR, XPS and in situ DRIRS. The current work not only revealed the relationship between the Lewis acidity of the support and catalytic performance, but also promotes the development of practical catalysts for CO esterification to DMC.
研究领域:
化学工程
·
催化科学
✓ 已验证
产品关联
DOI
高影响因子
危险品化学品经营许可证（带存储）