JOURNAL OF CHEMICAL THERMODYNAMICS
·
2017
·
IF 2.726
Dongshun Deng,Xiaobang Liu,Yanhong Cui,Yaotai Jiang
Solubilities of SO 2 have been determined in four biobased solvents (BBSs) at temperatures between 293.15 K and 323.15 K with 10 K intervals and pressure scope of (0–120.0) kPa using isochoric saturation method. The BBSs were selected from butyl lactate (BL), glyceryl triacetate (GT), triethyl citrate (TEC), and acetyl triethyl citrate (ATEC). Henry’s constants and thermodynamic properties such as Gibbs free energy , enthalpy and entropy of dissolution were derived from the solubility data. The gravimetric solubilities of SO 2 in BBSs were in the range of (0.07–8.52) mol.kg −1 and changed with the sequence of GT > BL > TEC ≈ ATEC. All the dissolution enthalpies were negative at each condition. The performances of SO 2 absorption in these solvents were further compared with those in some ionic liquids as well as common absorbents. The results illustrated that present BBSs possessed the potentiality as SO 2 absorbents due to their relatively large absorption ability, small absorption enthalpy, low toxicity, and biodegradability.
研究领域:
化学工程
·
环境化学
·
热力学
·
绿色溶剂
·
气体吸收
✓ 已验证
DOI
高影响因子
INTERNATIONAL JOURNAL OF ENERGY RESEARCH
·
2020
·Vol. 45
·期 4
·5337-5346
·
IF 3.741
Chuangang Yao,Jixing Yang,Haixia Zhang,Sigeng Chen,Jian Meng,Kedi Cai
Summary Cu doped perovskites SrFe 0.9- x Cu x Mo 0.1 O 3- δ (SFCM, x = 0-0.2) are explored as cathodes for IT-SOFCs. The influence of Cu doping on the property of SFCM series was studied in detail. The oxygen content decreases with the increase of Cu doping amount. SFCM samples are chemically compatible with LSGM electrolyte. However, the TEC values are still a bit higher than that of some common SOFC electrolytes. At 750°C, the R p values are 0.261, 0.227 and 0.155 Ω·cm 2 for SFCM0, SFCM0.1, and SFCM0.2. The obtained activation energies for x = 0, 0.1, and 0.2 are 1.01, 0.98, and 0.87 eV, respectively. These results indicate that Cu doping into SrFe 0.9- x Cu x Mo 0.1 O 3- δ has a favorable effect on the electrochemical activity of the materials.
研究领域:
材料科学
·
电化学
·
能源材料
·
固体氧化物燃料电池
·
无机功能材料
✓ 已验证
DOI
高影响因子
CORROSION SCIENCE
·
2022
·
IF 7.72
Tianquan Liang,Zhihua Huang,Menghao Li,Wantong Xiao,Huan He,Aoping He,Xiyong Chen,Nengneng Luo
The thermochemical reaction behaviors between Y 2 O 3 and calcium-magnesium-aluminosilicate (CMAS) at 1250 °C∼1400 °C were investigated. A continuous-dense reaction layer mainly composed of Y-apatite phase quickly forms within 15 min, and its slow increasing thickness depends on the molten CMAS infiltration along the Y-apatite grain boundaries, the dissolution of the Y-apatite phase into the melt, the inhibiting effect on the CMAS penetration, and the reaction time and temperature. The CMAS crystallization occurs due to the change of chemical composition and the formation of other reaction products. The dense reaction layer shows good resistance to the molten CMAS infiltration.
研究领域:
材料科学
·
无机非金属材料
·
高温材料
·
陶瓷涂层
·
腐蚀与防护
✓ 已验证
DOI
高影响因子
CERAMICS INTERNATIONAL
·
2017
·Vol. 44
·期 3
·3412-3416
·
IF 2.986
Rongxuan He,Wei Liu,Ziwei Wu,Di An,Meipeng Huang,Haidong Wu,Qiangguo Jiang,Xuanrong Ji,Shanghua Wu,Zhipeng Xie
In this work, a stereolithography-based method of 3D printing was successfully used to fabricate a complex-shaped triangular zirconia cutting tool with a tool withdrawal groove and a honeycomb ceramic component. The sintered bodies displayed significant shrinkage after sintering, with the maximum shrinkage being 35.26%. The XRD pattern indicated that the crystalline phase of the parts was the t-ZrO 2 phase, while SEM characterization revealed that the sintered bodies were composed of densely packed submicron-grade grains, without any discernible pores. The density of the parts was measured as 97.14% via Archimedes’ water displacement method, which is consistent with the results of SEM characterization. Additionally, the measured Vickers hardness and fracture toughness of the fabricated parts were 13.0597 GPa and 6.0380 MPa m 1/2 , respectively. These values are close to the structural properties of common zirconia ceramics prepared by conventional approaches. Hence, a novel DLP-stereolithography-based 3D printing process for the fabrication of complex and dense zirconia ceramic parts has been proposed in this work.
研究领域:
材料科学
·
先进制造
·
陶瓷工程
·
生物医学材料
·
增材制造
✓ 已验证
DOI
高影响因子
POLYMER DEGRADATION AND STABILITY
·
2018
·
IF 3.193
Anna Zheng,Yongkang Huang,Yang You,Jian Hu,Dafu Wei,Xiang Xu,Yong Guan
The heat resistance enhancement of fluorosilicone rubber (FSR) can make it more suitable for cutting-edge applications and extreme conditions. This paper focused on the antioxidant properties of boron particles for FSR and the corresponding mechanism. The thermal stability of FSR and FSR/boron composites was characterized by thermal gravimetric analysis (TGA), isothermal degradation and thermal-oxidative ageing. The results showed that boron significantly improved the thermal stability of FSR. In particular, the FSR/boron (100/10) composite retained 95% of its weight after isothermal degradation at 350 °C for 12 h, while the FSR lost 55% of its weight within the initial 1 h. The antioxidant mechanism of boron was further investigated by chemiluminescence (CL), electron paramagnetic resonance (EPR) and vulcanization curves. It was shown that boron has powerful radical scavenging activity (RSA) and inhibited the oxidation scission of the side groups. Moreover, boron revealed no RSA towards the tert-butoxy radical, ensuring the good vulcanization of the FSR/boron composites.
研究领域:
高分子材料科学
·
橡胶化学
·
功能复合材料
·
热稳定性能
·
抗氧化机制
✓ 已验证
DOI
高影响因子
BIOSENSORS & BIOELECTRONICS
·
2014
·
IF 6.451
Qin Xu,Lijuan Cai,Huijie Zhao,Jiaqian Tang,Yuanyuan Shen,Xiaoya Hu,Haibo Zeng
An enzymatic procedure based on a catalase biosensor for the detection of forchlorfenuron (CPPU) has been reported in this work. Catalase was immobilized on boron nitride (BN) sheets dispersed in chitosan by adsorption. The immobilized catalase exhibited direct electron transfer character and excellent electrocatalytic activity towards H 2 O 2 reduction. After introducing CPPU into the H 2 O 2 containing phosphate buffer solution , the catalase-catalyzed H 2 O 2 reduction current decreased. By measuring the current decrease, CPPU can be determined in the range of 0.5–10.0 µM with the detection limit of 0.07 μM. The non-competitive inhibition behavior of CPPU towards catalase was verified by the Lineweaver–Burk plots. Long stability character has been ascribed to this biosensor. Possible use of this biosensor in flow systems is illustrated. The proposed biosensor has been successfully applied to CPPU determination in fruits samples with satisfactory results.
研究领域:
分析化学
·
生物传感
·
食品安全
·
酶学
·
纳米材料
·
电化学
·
药物残留检测
✓ 已验证
DOI
高影响因子
POWDER TECHNOLOGY
·
2018
·
IF 3.23
Hongjing Wu,Shaohua Qu,Kejun Lin,Yuchang Qing,Liuding Wang,Yuancheng Fan,Quanhong Fu,Fuli Zhang
It has been rarely reported that the microwave absorption materials can exhibit excellent low-frequency EM wave absorbing properties. In this paper, we synthesized steady short carbon fibers (SCFs)@TiO 2 composites by using simple one-pot hydrothermal process. The conductive short carbon fibers could be separated by TiO 2 nanoparticles from each other and reduced the conductivity of composite materials as a whole, meeting the requirements of impedance matching . With the introduction of SCFs content, SCFs@TiO 2 composites showed improved tan δ E values at low frequencies, implying the enhanced microwave attenuation ability at low and medium frequency. We unexpectedly found that the SCFs@TiO 2 composites exhibited very strong absorbing peaks ( i.e. , −46.3 dB) at low frequencies with relatively thin matching thickness. Interestingly, when the thickness of the SCFs@TiO 2 composite was only 1.0 mm, the absorbing bandwidth with a RL value less than −10 dB was over 14.3–16.7 GHz ( i.e. , absorbing frequency bandwidth is 2.4 GHz).
研究领域:
材料科学
·
电磁功能材料
·
纳米复合材料
·
微波吸收材料
✓ 已验证
DOI
高影响因子
FUEL
·
2018
·
IF 4.908
Yu-hong Qin,Min-min Feng,Zi-bing Zhao,Stanislav V. Vassilev,Jie Feng,Christina G. Vassileva,Wen-ying Li
The ash fusion process of Jincheng anthracite ash, rice straw ash and coal-biomass ashes with different rice straw ash addition ratios during co-gasification under CO 2 atmosphere was elucidated by the ash fusion test, chemical analyses, optical heating stage microscopy (OHSM), X-ray diffraction and scanning electron microscopy equipped with energy-dispersive X-ray analyzer. Results showed that the initial sintering and initial melting temperatures of coal-biomass ashes observed by OHSM decreased with the addition of rice straw ash. The deformation temperatures determined by the ash fusion test were close to the initial melting temperatures. The biomass ash addition to coal ash introduced excessive amounts of alkaline compounds in the ash mixtures that led to lower initial temperatures of liquid phase formation. The ash fusion behavior of coal-biomass ashes with a rice straw ash addition ≤3 wt% was similar to that of coal ash and fits to the “softening-melting” ash fusion mechanism. In contrast, the ash fusion behavior of coal-biomass ashes with a greater addition of rice straw ash (>3 wt%) experienced dramatic changes at lower temperature and fits to the ‘‘melting-dissolution’’ ash fusion mechanism.
研究领域:
燃料化学
·
能源工程
·
热化学转化
·
燃烧学
·
灰化学
✓ 已验证
DOI
高影响因子
CHEMICAL ENGINEERING JOURNAL
·
2013
·
IF 3.473
Manhong Liu,Qiang Bai,Hailian Xiao,Yanyan Liu,Jun Zhao,William W. Yu
Colloidal platinum–ruthenium bimetallic nanoparticles with 2.3 nm were synthesized in solution and then immobilized on tin dioxide powder to make a supported nanocatalyst (Pt–Ru/SnO 2 ). The immobilized bimetallic nanoparticles had the same size and size distribution as the solution dispersed ones. Selective hydrogenation of o -chloronitrobenzene to o -chloroaniline was performed over the as-prepared Pt–Ru/SnO 2 nanocatalyst without using any solvent; 99.5% selectivity to o -chloroaniline at ∼100% conversion was achieved.
研究领域:
催化化学
·
纳米材料
·
有机合成
·
绿色化学
·
应用化学
✓ 已验证
DOI
高影响因子
Desalination and Water Treatment
·
2024
·
IF 1
Xu Zhang,Fan Yang,Jialing Qin,Huanghu Peng,Zezhou Chen,Lei Che,Shouxin Zhu,Wei Yang
The heterogeneous catalyst of CeO 2 /ZSM5 was applied to hydrolyze Congo red in subcritical water for the first time in the present study. The hydrolysis rate of Congo red could be significantly accelerated by introducing only 5 mg of 5% CeO 2 /ZSM5. The Congo red could be completely hydrolyzed at 220°C for 2 min—a reaction temperature 40°C lower than in the absence of 5% CeO 2 /ZSM5. In addition, the 5% CeO 2 /ZSM5 could be recycled for another run, and its Congo red hydrolysis efficiency and surface morphology showed no obvious change after 3 runs of recycling. The hydrolysis kinetics of Congo red in subcritical water could be well expressed by the Weibull model. The activation energy for hydrolysis of Congo red in subcritical water in the presence of 5% CeO 2 /ZSM5 (104.8 kJ mol –1 ) was much lower than in the absence of 5% CeO 2 /ZSM5 (155.9 kJ mol –1 ). The frequency factors were calculated to be 8.1 × 10 9 and 1.9 × 10 14 min –1 in the presence and absence of 5% CeO 2 /ZSM5, respectively. With these excellent properties, 5% CeO 2 /ZSM5 may prove to be an advantageous catalyst for the hydrolysis of Congo red in textile wastewater, in subcritical water.
研究领域:
环境化学
·
催化化学
·
水处理技术
·
绿色化学
·
反应动力学
✓ 已验证
DOI
高影响因子
JOURNAL OF POWER SOURCES
·
2017
·
IF 6.395
H.R. Jiang,W. Shyy,M.C. Wu,L. Wei,T.S. Zhao
The potential of B 4 C as a metal-free catalyst for vanadium redox reactions is investigated by first-principles calculations. Results show that the central carbon atom of B 4 C can act as a highly active reaction site for redox reactions , due primarily to the abundant unpaired electrons around it. The catalytic effect is then verified experimentally by cyclic voltammetry (CV) and electrochemical impedance spectroscopy (EIS) tests, both of which demonstrate that B 4 C nanoparticles can enhance the kinetics for both V 2+ /V 3+ and VO 2+ /VO 2 + redox reactions, indicating a bi-functional effect. The B 4 C-nanoparticle-modified graphite felt electrodes are finally prepared and tested in vanadium redox flow batteries (VRFBs). It is shown that the batteries with the prepared electrodes exhibit energy efficiencies of 88.9% and 80.0% at the current densities of 80 and 160 mA cm −2 , which are 16.6% and 18.8% higher than those with the original graphite felt electrodes. With a further increase in current densities to 240 and 320 mA cm −2 , the batteries can still maintain energy efficiencies of 72.0% and 63.8%, respectively. All these results show that the B 4 C-nanoparticle-modified graphite felt electrode outperforms existing metal-free catalyst modified electrodes , and thus can be promising electrodes for VRFBs.
研究领域:
电化学
·
能源材料
·
催化化学
·
储能技术
·
材料科学
✓ 已验证
DOI
高影响因子
MATERIALS LETTERS
·
2013
·
IF 2.224
Kejie Yu,Xuebin Zhang,Hongwu Tong,Xiangyan Yan,Shaomin Liu
Fibrous monodisperse core–shell structured Fe 3 O 4 /SiO 2 /KCC-1 nanoparticles were synthesised successfully through a surfactant-templated microemulsion formation process. The structure and morphology of the synthesised nanoparticles were investigated by scanning electron microscopy , transmission electron microscopy , superconducting quantum interference device susceptometer, X-ray diffraction, thermogravimetric analysis and N 2 adsorption/desorption. These nanoparticles showed monodisperse spherical morphology, high magnetism , good thermal stability , large surface area , direct channels, easily accessible large pores and narrow size distribution. A mechanism for the synthesis of these nanoparticles was proposed and explained. Adsorption experiments indicated that the as-prepared materials had good adsorption capacity for dye and could perform a fast transfer of molecules, indicating its promising application in purification of industrial wastewater, drug delivery and so on.
研究领域:
纳米医学
·
材料科学
·
环境工程
·
生物材料
·
药剂学
·
胶体与界面化学
✓ 已验证
DOI
高影响因子
危险品化学品经营许可证（带存储）