CHEMICAL ENGINEERING JOURNAL
·
2026
·
IF 12.5
Xin Zeng,Luxiang Ma,Jiacheng Li,Weiqing Lai,Huifang Li,Chaofei Song,Chunxi Hai,Shengde Dong,Yanxia Sun,Qi Xu,Xin He,Yuan Zhou
BO 3 3− lattice engineering expands LiFePO 4 channels for faster lithium extraction. • LFP-BO 3 electrodes provide good low-temperature performance. • LFP-BO 3 electrodes exhibit high selectivity in complex brine systems. To mitigate the sluggish lithium extraction kinetics of LiFePO 4 (LFP) constrained by intrinsic ionic channels in high-altitude, low-temperature salt lakes, this study employs a BO 3 3− lattice engineering strategy to induce lattice expansion and flexibilization in LFP by partially substituting PO 4 3− . Characterization confirms uniform BO 3 3− doping and dilated Li + channels. Electrochemical testing reveals that the optimized LFP-2%BO 3 electrode delivers outstanding kinetics, achieves an average lithium extraction of 9.8 mg·g −1 over eight cycles in the West Taijinar raw brine. Retaining 94.2% of its room-temperature Li + extraction capacity in a pure lithium solution at 0 °C, and achieves an average lithium adsorption of 20.21 mg·g −1 at −20 °C, which is more than twice that of the unmodified electrode. Furthermore, it enhances Li + selectivity while effectively suppressing the co-intercalation of Na + and Mg 2+ . The mechanism entails BO 3 3− widening channels and constructing robust transport networks to accelerate low-temperature ion migration. This study provides novel materials and theoretical insights for efficient lithium extraction from high-altitude, low-temperature salt lakes. Download: Download high-res image (236KB) Download: Download full-size image
✓ 已验证
产品关联
DOI
高影响因子
COLLOIDS AND SURFACES A-PHYSICOCHEMICAL AND ENGINEERING ASPECTS
·
2026
·
IF 5.4
Jian Gao,Deyi Zhuang,Bing Yu,Yun Fa,Wansheng Zhang,Xingyong Han,Huimin Li,Maocai Feng
A composite gel microsphere with a three-dimensional porous network structure has been developed: AO/SA-GQDs. • Under the same adsorption conditions, the introduction of GQDs increased the uranium adsorption capacity of the material from 52.584 mg·g −1 to 186.996 mg·g −1 . • AO/SA-GQDs composite gel microspheres exhibited a rapid U(VI) adsorption rate, reaching adsorption equilibrium within 300 min. • The highest experimental U(VI) adsorption capacity reached 231.593 mg·g −1 at 298.15 K and pH 5. • After five cycles, AO/SA-GQDs retained 84.99% of its initial adsorption capacity, with desorption rate above 80%. • The material is easy to prepare, and its raw materials are readily available and inexpensive, suggesting its potential for practical application. Stable uranium supply is essential for the development of nuclear power, and uranium extraction from seawater is regarded as a promising strategy for the sustainable development of nuclear energy. In this study, amidoxime-functionalized sodium alginate/graphene quantum dot composite gel microspheres (AO/SA-GQDs) were prepared via an in situ composite droplet-ion cross-linking method. Sodium alginate served as the matrix, amidoxime groups were introduced as U(VI)-specific binding sites, and graphene quantum dots (GQDs) were incorporated to regulate the pore structure and hydrophilicity of the microspheres. The AO/SA-GQDs microspheres exhibited a porous network structure, with a BET specific surface area of 42.997 m 2 ∙g −1 . Batch adsorption experiments showed that the optimal adsorption pH was 5. Adsorption kinetic analysis demonstrated that the AO/SA-GQDs microspheres reached adsorption equilibrium within 300 min, indicating a rapid U(VI) adsorption rate. At 298.15 K and pH 5, the highest experimentally measured equilibrium adsorption capacity was 231.593 mg∙g −1 , whereas the Langmuir-fitted maximum monolayer adsorption capacity was 244.499 mg∙g −1 . In the presence of various coexisting ions, the microspheres still maintained a high adsorption capacity for U(VI), demonstrating good selectivity. After five adsorption-desorption cycles, the adsorption capacity remained at more than 84% of its initial value, and the desorption efficiency remained above 80%. These results indicate that AO/SA-GQDs composite gel microspheres possess favorable adsorption capacity, selectivity, and recyclability, suggesting their potential for uranium extraction from aqueous environments. Download: Download high-res image (243KB) Download: Download full-size image
✓ 已验证
产品关联
DOI
高影响因子
CERAMICS INTERNATIONAL
·
2026
·
IF 6
Yixin Dong,Yansong Liu,Ying Zhang,Junzhan Zhang,Yongsheng Liu
Polymethyl methacrylate (PMMA) microspheres were used as pore-forming agents in the fabrication of porous silicon carbide (SiC) ceramics to control the pore structure and improve their high-temperature performance. PMMA microspheres reduced the viscosity and the overall attenuation coefficient of the SiC slurry, thereby improving its rheological stability and curing depth. As PMMA content increased from 0 to 60 vol%, open porosity rose from 26.27% to 54.98%, while bulk density decreased from 2.21 g/cm 3 to 1.53 g/cm 3 . PMMA decomposition generated uniform micrometer-scale spherical pores in the ceramic matrix. An appropriate open porosity enhanced thermal shock resistance by blunting crack tips and buffering thermal stress, while excessive open porosity caused stress concentration and accelerated crack propagation. The porous SiC ceramics containing 20 vol% PMMA microspheres exhibited the highest thermal shock resistance, with a critical temperature difference ( Δ T c ) of 338.3 °C.
✓ 已验证
产品关联
DOI
高影响因子
CERAMICS INTERNATIONAL
·
2026
·
IF 6
Lin Wang,Chenfei Gao,Yuhang Jiang,Zepeng Xu,Han Wei,Kangkang Yuan,Xiaotong Jin
Structural evolution is essential for the fundamental understanding of high-temperature behavior and optimizing of ceramic micro/nanofibers. In the present work, the effects of structural evolution on the high temperature stability and flexibility of Al 2 O 3 -ZrO 2 -La 2 O 3 (AZLO) fibrous membranes were fully investigated. The evolution of precursor fiber pyrolysis, phase transformation and microstructure were characterized by TG/DSC, IR, XRD, SEM, ESB and HRTEM. From 800 to 1200°C, the dual-phasic structure of amorphous Al 2 O 3 and fine ZrO 2 and La 2 Zr 2 O 7 grain contributed to the thermal stability and flexibility of AZLO fibrous membranes. At 1300°C, solid-state metathesis reaction between amorphous Al 2 O 3 and intermediate phase La 2 Zr 2 O 7 led to the formation of fine LaAl 11 O 18 and ZrO 2 grain. The interlaced distribution of fine ZrO 2 particles and platelet-like LaAl 11 O 18 became the new fundament of thermal stability and flexibility of AZLO fibrous membranes. AZLO fibrous membranes could maintain its excellent high temperature stability and flexibility up to 1300°C and possessed a low room temperature thermal conductivity of 35.7 mW m −1 K −1 . The present work provided a novel perspective for the rational design of Al 2 O 3 -ZrO 2 fibers from the view of structural evolution.
✓ 已验证
产品关联
DOI
高影响因子
COLLOIDS AND SURFACES A-PHYSICOCHEMICAL AND ENGINEERING ASPECTS
·
2026
·
IF 5.4
Yufei Wang,Yiyang Lin,Wei Tao,Yuqing Zhu,Jiacheng Niu,Yikun Liao,He Feng
Malachite green (MG) is a triphenylmethane dye resistant to degradation, possessing high toxicity, carcinogenicity, and mutagenicity, and co-existing bacterial contamination affects water safety. In this work, CuO-loaded sepiolite (CuO/Sep) nanocomposites were synthesized by an ammonia-driven deposition–precipitation method (ADP) to simultaneously remove MG and exhibit antibacterial activity. The nanocomposite with 10 wt% CuO had a specific surface area of 166.5 m 2 /g. The adsorption kinetics conformed to the pseudo-second-order kinetic model, and the equilibrium adsorption data could be described by the Langmuir model. At 295 K, the maximum monolayer adsorption capacity reached 809.6 mg/g, and the decolorization rate for an MG solution with an initial concentration of 50 mg/L reached 99%. The adsorption process involved a synergistic effect of physical and chemical adsorption, representing an endothermic reaction (ΔH = +55.36 kJ/mol). In addition, the composite exhibited good antibacterial activity, with antibacterial rates reaching 99.9% against Staphylococcus aureus and 97.5% against Escherichia coli . These results indicate that the synthesized CuO/Sep nanocomposite possesses both good MG adsorption capacity and broad-spectrum antimicrobial properties. Download: Download high-res image (277KB) Download: Download full-size image
✓ 已验证
产品关联
DOI
高影响因子
Journal of Cleaner Production
·
2026
·
IF 10.7
Lu He,Jingxian Qin,Wei Liu,WeiWei Zhu,Xuejuan Cao,Shaoyun Guo,Jiabin Shen
PCTFE microporous membrane fabricated via sacrificial template method. • Custom-tailored pore sizes (0.31 to 1.28 μm). • Remarkable capability in separating various oil/water mixtures and emulsion. • Excellent creep resistance, mechanical properties and corrosion resistance. The efficient purification and recycling of oily waste rely heavily on membrane separation technology, where fluoropolymer-based membranes hold particular promise. This study demonstrated a sacrificial template strategy to fabricate polychlorotrifluoroethylene (PCTFE) membranes with tunable pore architectures. This approach leveraged a solvent-assisted process to incorporate a fluoroelastomer (FR) template, forming PCTFE/FR sintered films. By controlling FR content, sintered films with co-continuous morphology can be obtained, which subsequently enabled the formation of penetrating pore structure. A key finding was the linear correlation between sintering time and phase size, which provides precision in pore structure control, complemented by the use of smaller PCTFE particles for refining the phase morphology. The optimized membranes integrated strong hydrophobicity/oleophilicity, robust mechanical properties, excellent creep resistance, and efficient oil/water separation performance. They delivered high separation fluxes (15351 L/(m 2 h) for oil/water mixtures; 7649 L/(m 2 h) for emulsions) with superior efficiency (>99%) and oil purity (>99.95 wt%). Moreover, they retained excellent performance after 15 operational cycles or 7-day immersion in various corrosive media (including DMF, DMAc, 1M H 2 SO 4 , 1M NaOH and concentrated HNO 3 ), with no significant performances degradation observed. These findings underscore the great potential of the developed membranes for treating and recycling oily wastes, even under harsh environmental conditions. Download: Download high-res image (464KB) Download: Download full-size image
✓ 已验证
产品关联
DOI
高影响因子
Green Chemical Engineering
·
2026
·
IF 11.9
Jiaxin He,Shangqi Zhou,Lisha Guo,Siying An,Rui Bai,Wenxiu Ma,Jin Lin,Jichao Zhang,Menglei Yuan,Jian Zhang
Palladium single-atom catalysts show exceptional catalytic performance in nitrile butadiene rubber (NBR) hydrogenation due to their unique unsaturated coordination environments. However, the hydrogenation activity and atomic efficiency are seriously limited by inherent instability of undercoordinated Pd δ+ sites and poor support structure, leading to decreased hydrogenation degree and cycling stability. In this work, a novel single-atom palladium catalysts was developed, where undercoordinated single-atom Pd δ+ sites are steadily anchored onto CeO 2- x nano-islands supported by SiO 2 (Pd 1 /CeO 2- x /SiO 2 ). The strong metal-interaction of CeO 2- x nano-islands immobilize the undercoordinated Pd δ+ sites to enhance adsorption of olefin bonds in NBR, while SiO 2 promotes mass transfer diffusion of NBR and atomic efficiency of palladium. The Pd 1 /CeO 2- x /SiO 2 thus achieves an unprecedented hydrogenation degree of up to 99.8% without decrease over a 10-runs stability test in selective hydrogenation of NBR, outperforming previously state-of-the-art catalysts. Consequently, this work will offer a new strategy for single-atom catalysts to achieve high steady-state activity in selective hydrogenation.
✓ 已验证
产品关联
DOI
高影响因子
Journal of Energy Storage
·
2026
·
IF 10.7
Hongqiang Ma,Zelong Lei,Zijie Hong,Jingjing Feng
The sandwich-structured supercapacitor was fabricated using an alkali-activated fly ash-slag (AAFS) electrolyte and activated carbon-loaded nickel foam electrodes. This study systematically evaluated the effects of fly ash-slag mass ratio, Na 2 O concentration, soaking environment, and curing age on the pore structure and microscopic morphology of the AAFS electrolyte, as well as the ionic conductivity and energy storage performance of the supercapacitor. The results indicate that the fly ash-slag mass ratio governs electrochemical performance; specifically, decreasing the slag content significantly enhances ionic conductivity and volumetric specific capacitance. The S 25 sample achieves an optimal balance between mechanical and electrochemical properties, exhibiting a compressive strength of 43.47 MPa and a volumetric specific capacitance of 14.95 mF/cm 3 . It maintains a 70.69% capacitance retention after 500 charge-discharge cycles, with energy and power densities reaching 1.95 μWh/cm 3 and 48.46 μW/cm 3 , respectively. When connected in series, these devices successfully power LEDs. Microstructural analysis reveals that high fly ash systems predominantly comprise N-A-S-H gels. The high proportion of gel pores and mesopores within these gels provides low-resistance pathways for ion transport. Increasing the Na 2 O concentration only slightly improves electrochemical performance, while prolonged curing increases ion transport resistance due to gel network densification. The energy storage mechanism is based on electrical double-layer capacitance (EDLC). Their overall performance is determined by both the gel phase composition and pore structure. This study provides crucial experimental and theoretical foundations for the engineering application of structural supercapacitors.
✓ 已验证
产品关联
DOI
高影响因子
Journal of Energy Storage
·
2026
·
IF 10.7
Yue Zhang,Run Liu,Zheng Gong,Xin He,Peisen Han,Hongbo Wang,Yinhua Zhou,Changhai Zhang,Yongquan Zhang,Tiandong Zhang
With the rapid development of high-power electronic devices and renewable energy systems, the demand for high-performance dielectric energy storage materials has continuously increased. Conventional polyester films (e.g., biaxially oriented polypropylene, BOPP) and polyimide (PI) exhibit relatively high breakdown strength ( E b ), however, under high electric fields, they suffer from non-uniform electric field distribution and aggravated energy dissipation, making it difficult to simultaneously achieve high energy density ( U d ) and high charge discharge efficiency ( η ). Although polymer dielectrics generally possess high E b and excellent η , their inherently low dielectric constant ( ε r ) constrains further improvement in energy storage performance. To overcome these limitations, we designed and fabricated an asymmetric trilayer heterostructure with an insulating-transition-polarization architecture. The transition layer comprises blends of poly(vinylidene fluoride) (PVDF) with poly(methyl methacrylate) (PMMA), poly(ethersulfone) (PESU), and polyimide (PI), which synergistically regulate the internal electric field distribution and suppress local field distortion. Experimental results demonstrate that the optimized A/3 A-7F/F composite achieves U d of 15.3 J/cm 3 and η of 77.4%, corresponding to improvements of 88.9% and 86.5% compared to pristine PVDF, respectively. These findings provide a promising strategy for enhancing the energy storage performance of polymer dielectrics, with direct implications for high-efficiency capacitive energy storage systems.
✓ 已验证
产品关联
DOI
高影响因子
MICROCHEMICAL JOURNAL
·
2026
·
IF 5.2
Zhongzhou Si,Haodong Chen,Shakoor Kashif,Ting Li,Fanghui Ma,Minghui Yang
Copper nanoclusters were synthesized based on 4-mercaptobenzoic acid (P-MBA) as template. • The addition of small molecule terephthalic acid (PTA) can enhance the fluorescence intensity. • The reaction between PTA and ascorbic acid can produce a blue fluorescent substance PTA-OH. • Acid phosphatase can catalyze the hydrolysis of l -ascorbic acid-2-phosphate to AA. • A ratiometric fluorescence assay for acid phosphatase was developed. Copper nanoclusters were synthesized based on 4-mercaptobenzoic acid (P-MBA) as template (P-MBA-CuNCs). Small molecule terephthalic acid (PTA) was then utilized to modify P-MBA-CuNCs and enhance the fluorescence intensity. Individual P-MBA-CuNCs were self-assembled into nanosheet aggregates in aqueous solution due to π-π stacking and hydrogen bonding interactions. These inter-cluster interactions accelerated the nonradiative process, resulting in quenching of the fluorescence. However, there is strong interaction between PTA and P-MBA, which blocks the inter-cluster interaction of CuNCs and enhances the fluorescence emission. In addition, the reaction between PTA and ascorbic acid (AA) can produce a blue fluorescent substance PTA-OH. Acid phosphatase (ACP) can catalyze the hydrolysis of l -ascorbic acid-2-phosphate (AAP) to AA. Therefore, a ratiometric fluorescence assay for ACP was constructed based on the CuNCs/PTA system with fluorescence intensity of CuNCs unchanged and fluorescence intensity of PTA-OH increased. The assay has linear response to ACP in the concentration range of 0.01–15 U/L, with detection limit as low as 0.003 U/L. The method was successfully applied to determination of the ACP in the human serum samples. Ratio fluorescence assay for acid phosphatase based on 4-mercaptobenzoic acid templated copper nanoclusters. Download: Download high-res image (111KB) Download: Download full-size image
✓ 已验证
产品关联
DOI
高影响因子
ELECTROCHIMICA ACTA
·
2026
·
IF 5.8
Fuqian Hei,Yimin Zhang,Tao Liu,Nannan Xue,Hong Liu,Zhenggang Luo
VCN cannot be used as a catalyst for the VRFB positive electrode. • The introduction of VCN and CNT can increase the specific surface area of graphite felt and add active sites, thereby improving the catalytic performance of the negative electrode. • At 180 mA·cm⁻², the VRFB using VCNT@GF as the negative electrode achieved a VE of 82.8% and an EE of 78%. This study employs a carbon thermal reduction method to synthesize vanadium carbonitride (VCN) powder using V 2 O 3 and acetylene black as raw materials. By modifying graphite felt (GF) with VCN powder and carbon nanotubes (CNT), a VCNT@GF composite electrode was successfully prepared and applied in a vanadium flow redox battery(VRFB). The results indicate that VCN@GF cannot serve as a positive electrode for VRFB due to the instability of the positive electrolyte within the 0.4–1.4 V potential range. In comparable terms, the VCNT@GF electrode exhibits catalytic activity towards the V²⁺/V³⁺ redox coupling system within a potential range of -0.9 to -0.1 V. VRFB assembled with VCNT@GF as the negative electrode achieved a voltage efficiency of 82.8% and an energy efficiency of 78% at 180 mA·cm⁻²(GF at 79% and 75.5%). After 200 cycles of testing, both voltage and energy efficiency remained stable, demonstrating good cycling stability. This CNT assisted VCN modification strategy substantially enhances GF electrode performance, providing a viable pathway for developing high-performance VRFB negative electrode materials. Download: Download high-res image (252KB) Download: Download full-size image The purple one among the vanadium ions should be V 2+ . Please help me modify it, or replace it with the new version I provided.
✓ 已验证
产品关联
DOI
高影响因子
PROCESS SAFETY AND ENVIRONMENTAL PROTECTION
·
2026
·
IF 7.9
Jianglin Yin,Yihua Qian,Xiaohui Dou,Qing Wang,Bingbing Lai,Qian Jia,Xiaobo Wang
Effective thermal management is critical for the reliable operation of lithium-ion battery systems, as excessive heat accumulation may lead to performance degradation and safety risks. This study develops a low-viscosity, synthetic ester-based nanofluid as an environmentally friendly immersion coolant for 18650 battery modules. Surface-modified Si 3 N 4 nanoparticles were stably dispersed in the ester base to form a homogeneous nanofluid. Thermal characterization under static and dynamic immersion-cooling conditions demonstrates enhanced thermal conductivity, improved heat-dissipation capability, and reduced temperature gradients, while maintaining low viscosity and favorable pumping performance. Dynamic cooling experiments show a maximum battery temperature reduction of 12.78% compared with conventional transformer oil under identical operating conditions. The interfacial modification of nanoparticles contributes to reduced thermal resistance and improved heat transfer pathways. In addition, the synthetic ester base exhibits good biodegradability and low aquatic toxicity, indicating favorable environmental compatibility. Overall, this work provides a thermally efficient and environmentally benign immersion cooling strategy that improves the operational thermal management performance of lithium-ion battery systems and enhances their thermal safety margin under normal operating conditions. Download: Download high-res image (272KB) Download: Download full-size image
✓ 已验证
产品关联
DOI
高影响因子