COLLOIDS AND SURFACES A-PHYSICOCHEMICAL AND ENGINEERING ASPECTS
·
2026
·
IF 5.4
Lin Li,Kaiyun Yang,Zhan Ding,Chang Liu
Spodumene, a key source of strategic lithium, is often difficult to separate and typically occurs in low-grade ores due to its common association with silicate gangue minerals such as quartz. This study introduces the cationic surfactant benzethonium chloride (BC) as a novel collector for the reverse flotation separation of quartz from spodumene. Systematic single-mineral flotation tests evaluated the selectivity of BC toward the two minerals, and artificial mixed-ore experiments confirmed its practical separation efficiency. Under optimized conditions (pH 6, BC concentration = 5 × 10 −2 mmol/L), effective separation was achieved, yielding a spodumene concentrate with a Li 2 O grade of 4.96% and a recovery of 73.61%. Interfacial mechanisms were elucidated through contact angle, zeta potential, atomic force microscopy (AFM), Fourier-transform infrared spectroscopy (FTIR), and X-ray photoelectron spectroscopy (XPS). The results show that BC significantly enhances quartz hydrophobicity mainly through electrostatic adsorption and synergistic multi-form hydrogen-bond interactions, whereas its adsorption on spodumene is markedly weaker. This contrast enables selective quartz flotation and efficient separation. In summary, BC demonstrates strong potential as a new collector for spodumene reverse flotation, offering both a practical reagent alternative and a theoretical basis for effective spodumene-quartz separation.
✓ 已验证
产品关联
DOI
高影响因子
JOURNAL OF ALLOYS AND COMPOUNDS
·
2026
·
IF 6.7
Ubaid Ur Rehman,Kashaf Ul Sahar,Qian Wang,Mazhar Hussain Danish,Chun-Ming Wang
Achieving high thermoelectric efficiency in oxide ceramics requires the simultaneous optimization of charge transport and suppression of lattice thermal conductivity. Here, we report a combined entropy and vacancy engineering strategy to tailor the transport properties of SrTiO 3 -based perovskites. A series of A-site-deficient high-entropy compositions, (Sr 0.2 Ba 0.2 La 0.2 Ca 0.2 K 0.2 ) 1- x TiO 3 (0 ≤ x ≤ 0.10), were synthesized and systematically characterized. Structural analyses confirm the formation of a stable single-phase cubic perovskite structure stabilized by high configurational entropy. The introduction of A-site vacancies induces charge compensation through partial reduction of Ti 4 + to Ti 3+ , thereby increasing electron concentration, while simultaneously enhancing lattice distortion and phonon scattering. As a result, the lattice thermal conductivity is significantly reduced without a severe degradation of carrier mobility. The optimal composition at x = 0.05 exhibits a maximum power factor of ∼796 μW/mK 2 and a maximum ZT of 0.22 at 773 K. In addition, the ceramics maintain high mechanical hardness, highlighting the potential of entropy-vacancy coupling as a viable route for thermally and mechanically robust oxide thermoelectrics.
✓ 已验证
产品关联
DOI
高影响因子
HYDROMETALLURGY
·
2026
·
IF 6.3
Bingxu Chen,Chunliu Li,Huaijiang Wang,Ruishu Wang,Yingfeng Cuan,Haojie Meng,Bingwu Chu
High strength, temperature resistance, and corrosion resistance are vital for energy storage technologies, which has led to increased demand for vanadium and molybdenum in the high-tech sector, particularly in aerospace, electronics, and defense. The presence of heteropolyacid ions such as MoV 9 O 28 5− and HMoV 9 O 28 4− has a detrimental effect on the separation of vanadium and molybdenum, with severe adverse consequences for the purity of the products derived from these elements. This study proposes a novel method for the gradient separation of vanadium and molybdenum from acidic solutions. First, phase reconstruction of MoV 9 O 28 5− and HMoV 9 O 28 4− is achieved through the synergistic effects of H 2 O 2 , H + , and NH 4 + . Vanadium and molybdenum are precipitated as a mixed precipitate of (NH 4 ) 2 V 6 O 16 and H₂MoO₅. Second, the reduction reaction of H 2 MoO 5 in acetic acid solution is employed for the selective dissolution of molybdenum, and the molybdenum content in the ammonium polyvanadate is reduced to below 0.006%. Finally, the molybdenum in acetic acid is converted to a MoO 3 product with a purity of 99.9% via evaporative crystallization and roasting. This environmentally friendly process efficiently separates vanadium and molybdenum in acidic media using a phase reconstruction method. The proposed method is also applicable to systems containing nickel, aluminum, and other impurities.
✓ 已验证
产品关联
DOI
高影响因子
JOURNAL OF SOLID STATE CHEMISTRY
·
2026
·
IF 3.2
Shi-Chun Zhang,Xue-Shan Yu,Yong-Ming Zhang,You-Feng Wang,Wei-Bin Ma,Ai-Jun Jiao,Zhi-Wei Li,Tong Su,Zhen-Hai Fu
The "cold decomposition-direct flotation" method is presently the predominant technique for KCl production from carnallite ore. However, this process has been hindered by the interactions between NaCl and KCl, resulting in suboptimal product purity and the potassium recovery rate. This study investigated the influence of the decomposition solution's composition on the concentrate grade of KCl. Initially, flotation tests with NaCl and KCl mixtures revealed that fine and newly formed NaCl adversely affected concentrate grade of KCl. Subsequently, we investigated the effects of NaCl, KCl, and MgCl 2 solutions as decomposition solution on the grade of KCl flotation concentrates. The results showed that higher MgCl 2 concentrations significantly increased particle size and concentrate grade of KCl. Additionally, experiments with diluted decomposition mother liquor (the triple-saturation point E) demonstrated that lower dilution ratios enhanced concentrate grade of KCl, suggesting that the decomposition mother liquor can be adjusted to an appropriate concentration for the decomposition of carnallite ores in industrial applications. This study provides valuable insights for addressing the challenges of low concentrate grade and the inefficient utilization of carnallite ore.
✓ 已验证
产品关联
DOI
高影响因子
COMPOSITES PART B-ENGINEERING
·
2026
·
IF 14
Jv Li,Chunwang Xu,Hongmei Chen,Kejing Yu,Gang Liu,Fenghua Zhang,Wenbing Li
Designing flexible electromagnetic interference (EMI) shielding materials that transition from static shielding to dynamic adaptability remains a significant challenge in the development of next-generation electronic protection. In this study, we fabricated a reusable flexible polyimide (PI)/MXene/silver nanowires (AgNWs) (PMA) EMI shielding composite film by assembling MXene and AgNWs onto a shape-memory PI matrix using a vacuum-assisted filtration technique. When the ratio of MXene to AgNWs was 2:1, the composite film exhibited a maximum electrical conductivity of 132 S/cm and an EMI shielding effectiveness of 60.68 dB in the X-band (8.2-12.4 GHz). After further optimizing the material structure, the gradient-structured PMA composite film (G-PM 2 A 1 ) achieved a shielding effectiveness of 67.85 dB. The shielding performance remained essentially unchanged under harsh conditions, including ultrasonic cleaning, acid corrosion, high temperature (250 °C), and low temperature (−196 °C). Owing to the intrinsic shape-memory properties of polyimide, the film could recover its original structure after repeated deformation-heating cycles, maintaining an EMI shielding effectiveness above 60 dB. Moreover, the composite film exhibited excellent thermal stability, mechanical strength, and flame retardancy. Its lightweight, flexibility, and environmental stability indicate potential for localized EMI shielding applications relevant to electric vehicle battery systems, where lightweight, flexible, and environmentally robust shielding layers are required.
✓ 已验证
产品关联
DOI
高影响因子
JOURNAL OF MATERIALS SCIENCE & TECHNOLOGY
·
2026
·
IF 16.8
Hui Li,Faming Zhang,Xiang Liu,Wei Zheng,Guobing Ying
High-entropy MAX (HE-MAX) phases and their derivative MXenes (HE-MXenes) have attracted widespread attention due to multicomponent modulation effects. Herein, a (TiZrNbTa) 2 AlC HE-MAX phase with high purity of 96.18 wt.% was synthesized. The ceramic exhibits a low lattice thermal conductivity of 4.56 W/(m K) because of strong phonon scattering at the M-site. Superior mechanical performances were achieved, including Vickers hardness of 7.2 GPa, flexural strength of 494 MPa, compressive strength of 1643 MPa, and fracture toughness of 6.8 MPa m 1/2 . The strength enhancement is attributed to local chemical fluctuations and wavy-distributed lattice strain fields that create rugged energy landscapes and impede dislocation motion. Whereas the nearly cubic stacking of [M 6 X] octahedron promotes homogeneous deformation and achieves a comparable fracture toughness to Ti 2 AlC. The derived HE-MXene maintains hexagonal symmetry with enlarged interlayer spacing and mixed M-site valence states. Density functional theory calculations reveal a Young’s modulus of 252 GPa and metallic character with Nb serving as the dominant redox‑active center. This work offers a generalizable strategy for strengthening MAX phases via a high-entropy design, highlighting their potential for lightweight structural applications.
✓ 已验证
产品关联
DOI
高影响因子
CHEMICAL ENGINEERING SCIENCE
·
2026
·
IF 5.1
LiJun Tang,Xue Liang,Xiaodong Zhu,Jian Gao
The rise of Na-storage devices has imposed more stringent demands on storage electrode materials with large capacity, long service life, and fast rate capability. However, the application of electrode material is still hampered by its poor electrical conductivity and severe volume expansion. Herein, the reduced graphene oxide-based composite aerogel (rGO gel) is fabricated by implementing a self-shrinking strategy and leveraging the columnar support effect of one-dimensional nano-gaskets (T-Nb 2 O 5 and CNT). Benefiting from the synergistic effect of nano-gaskets and pore structure design, the composite electrode enhances the mechanical strength while buffering the volume change of the active materials. The well-connected conductive network not only promotes the diffusion of Na + but also provides abundant accessible active sites. Therefore, a half-cell assembled using rGO/T-Nb 2 O 5 as working electrode achieves maximum specific capacity of 546.5 mAh g −1 at 0.1 A g −1 . Moreover, the constructed 3D rGO/T-Nb 2 O 5 //rGO/CNT sodium-ion hybrid supercapacitor delivers a mass specific capacitance of 96.5F g −1 at the current density of 2.0 A g −1 . In addition, the high mass energy density of 66.2 Wh kg −1 and power density of 2225 W kg −1 are demonstrated. This work provides a novel structural design strategy for advancing high-performance Na-storage devices.
✓ 已验证
产品关联
DOI
高影响因子
WATER RESEARCH
·
2026
·
IF 12.8
Bin Chen,Weihu Zhang,Yunyun Guo,Yuan Bai,Lele Cui,Wenheng Jing
Electrochemical synthesis of hydrogen peroxide (H 2 O 2 ) presents a sustainable paradigm for decentralized chemical manufacturing, yet its practical implementation is severely impeded by catastrophic scaling in tap water electrolytes. Here, we reveal that on conventional gas diffusion electrodes, localized alkalinity-induced scaling precipitates a fatal hydrophilic transition, triggering irreversible water flooding and failure. To circumvent this, we introduce a structurally discontinuous electrode architecture engineered with artificial micro-cracks, which demonstrates exceptional stability for over 800 h at 100 mA cm −2 in tap-water-based electrolytes while maintaining a Faradaic efficiency >80 %. Operando electrochemical reflection-absorption imaging elucidates a unique tolerance mechanism wherein the crack channels retain their hydrophobicity and gas permeability to support sustained reaction despite the severe deactivation of catalyst islands by scaling. Leveraging this design, we engineer a scaled-up, membrane-free electrolyzer that, operating directly with tap water at 100 mA cm −2 , achieves high-throughput H 2 O 2 production (600 mL min −1 ) for >200 h. This work resolves the critical hardness tolerance bottleneck, establishing a robust foundation for the deployment of on-site H 2 O 2 electrosynthesis in diverse real-world water matrices.
✓ 已验证
产品关联
DOI
高影响因子
CHEMICAL ENGINEERING JOURNAL
·
2026
·
IF 12.5
Zihao Yu,Qiulu Chu,Shufang Wu,Qiong Wang
To reduce reliance on petroleum-based plastic packaging, this study explored the application of persimmon juice fermentation products (PF) as a fully bio-based coating for paper-based packaging with enhanced physicochemical properties. PF was prepared through natural fermentation of unripe persimmon juice, and subsequent chemical composition analysis revealed that it is rich in tannin (1.38%) and pectin (2.70%). Paper coated with multiple PF layers exhibited significantly improved physical and mechanical strength, achieving a maximum tensile index of 122.2 N·m/g, along with enhanced barrier performance (air permeability reduced by 99.7%), antibacterial activity, and recyclability. Furthermore, the underlying mechanism for the improved mechanical and barrier performance of the PF-coated paper was investigated. Results indicate that the reinforcement is primarily governed by a physically multilayer adsorption of PF constituents, tannin, and pectin onto cellulose fiber. During coating, hydrogen bonding between hydroxyl groups of tannin and cellulose played a predominant role in enhancing the tensile and burst strength of coated paper. Meanwhile, pectin acted as a binder to bridge fibers and tannins, thereby improving the folding endurance and water resistance of the paper. This work demonstrates that PF represents a promising coating for producing recyclable and antibacterial paper-based packaging with expected barrier properties, offering a sustainable and multifunctional alternative for the packaging industry.
✓ 已验证
产品关联
DOI
高影响因子
JOURNAL OF MOLECULAR LIQUIDS
·
2026
·
IF 5.2
Fangxu Li,Qing Tang
To enhance the enrichment efficiency of copper oxide ores, calcium polysulfide (CaSx) in combination with potassium n-butoxypropyl xanthate (BPX) was applied for the sulfidization flotation of malachite in this study—marking the first reported use of this reagent system for such a purpose. Flotation experiments demonstrated that the CaSx-BPX system exhibited superior selectivity and separation performance for malachite relative to calcite and quartz, outperforming three reference systems: CaSx-Sodium isobutyl xanthate(IBX), Na 2 S-BPX, and Na 2 S-IBX. Under optimized conditions (pH = 7, CaSx dosage of 200 mg/L, and BPX dosage of 100 mg/L), the recovery of malachite, calcite, and quartz were 98.23%, 5.89%, and 2.35%, respectively. Zeta potential analyses showed a negative shift in the surface potential of malachite over the pH range of 7–12 after the addition of CaSx, followed by a further negative shift upon BPX adsorption. The XPS results further indicate that CaSx forms stable Cu(I/II)–S chelates on the malachite surface. Subsequently, the sulfided malachite chemically reacts with BPX to form C–S–Cu(I/II) chemical bonds. Contact angle measurements revealed that malachite undergoes a transition from hydrophilic to hydrophobic upon treatment with CaSx–BPX, whereas calcite and quartz retain their hydrophilic nature. This differential wettability provides a rational explanation for the high flotation selectivity achieved among the three minerals.
✓ 已验证
产品关联
DOI
高影响因子
CONSTRUCTION AND BUILDING MATERIALS
·
2026
·
IF 8.9
Xiaotong Wang,Lin li,Shuai Zhang,Dengxun Ren,Pan He,Shuangqiao Yang,Rui Han
With the growing concern of building energy consumption and increasingly severe global warming, passive daytime radiative cooling (PDRC) provides a sustainable thermal regulation solution due to its energy-free and environment-friendly properties. Here, basing on structure design, we fabricated a high-efficient flexible bilayer thermoplastic polyurethane (TPU) coating, which was consisted with the bottom porous TPU/titanium dioxide (TiO 2 ) as the solar reflector, and the upper TPU/hollow glass beads (HGB) to improve the long-wave infrared emission, ultraviolet band reflection and thermal insulation. The synergism between the selectively-functionalized bilayer structure brings the bilayer TPU/HGB/TiO 2 coating with high solar reflectivity of 95.1% and longwave infrared emissivity of 91.6% when the upper/bottom thickness ratio is set at 2:8 and total thickness of only 400 μm. On the base of single layer TPU/TiO 2 coating, the bilayer coating shows an incremental improvement. And the coating exhibits satisfactory ductility and mechanical strength, achieving a tensile strength of 3.3 MPa and elongation at break of 424.2%. Taking advantages of both the high optical and mechanical performances, the bilayer coating achieves a net cooling power of 103.0 W·m −2 , and a passive temperature reduction of −4.7 ℃ and −9.5 ℃ compared to TPU/HGB and cement sample respectively during the outdoor radiative cooling test. The coating demonstrates real-time temperature drops of 10.0 ℃ and 22.4 ℃ for the car model and bicycle cushion cooling under our testing conditions respectively. And showed potential for the application in sustainable building cooling and vehicle cooling applications.
✓ 已验证
产品关联
DOI
高影响因子
Nature Sustainability
·
2026
·
IF 32.1
Jin Xianchun,Lei Lin,Du Jinyan,Wang Fuqiang,Long Zhihe,He Yongping,Xing Lili,Zhao Xiaochong,Xue Xinyu
Uranium (U) is essential for the nuclear power industry and plays an important role in decarbonizing the energy supply. However, concern regarding the sustainability of U supply is growing, as conventional U ore reserves are scarce and common mining practices have a notable environmental footprint. Exploring alternative U sources and developing sustainable extraction methods are therefore desired. Here we show a spontaneous U extraction strategy based on droplet falling. Specifically, naturally falling salt-lake water droplets interact with a film of aluminium–fluorinated ethylene propylene–chitosan coated on carbon felt, converting mechanical energy into electricity and driving an in situ electrochemical process for spontaneous U extraction. Electrons released at the solid–liquid interface on a superhydrophobic fluorinated ethylene propylene surface reduce U(VI) adsorbed by chitosan to U(IV), ultimately forming U(VI) precipitates. Field experiments conducted in real salt-lake environments with high salinity confirm the scalability and robustness of droplet U extraction, yielding magnesium uranate (MgU 2 O 7 ) and sodium polyuranate (Na 2 U 7 O 22 ) as the main products. A multistep device reduces the U concentration of salt-lake water from 173 μg l −1 to 34 μg l −1 (extraction efficiency of 80.3%) with minimal extraction of co-existing ions. Overall, this work offers a viable pathway to sustainable U resource extraction.
✓ 已验证
产品关联
DOI
高影响因子