文献检索

查找使用阿拉丁产品的科研文献

检索与阿拉丁产品相关的同行评审论文、DOI、PubMed 编号、期刊、作者、CAS 号及研究领域。

科研影响力快照

与阿拉丁产品相关的已发表科研成果

在搜索之前,这些指标可帮助访客快速了解产品关联科研的规模与质量。

347,389+ SCI 论文 与阿拉丁产品引用相关
2,303,681.05 总影响因子 匹配文献记录中影响因子的总和
81.20 最高期刊影响因子 匹配期刊中的最高 IF
6.63 平均期刊影响因子 匹配文献的平均 IF

参考指标 指标基于阿拉丁文献引用数据库及期刊影响因子记录。文献关联仅供科研参考,请以原始文献为准。

产品列表

视图 列表 网格

显示第2089至2100个,产品总数347,389个

切换升序
Journal of Environmental Chemical Engineering · 2026 ·Vol. 14 ·期 2 ·122156 · IF 7.5

In-situ synthesis of hydrophobic nano-calcium carbonate via CO2 mineralization of titanium gypsum and its enhancement on epoxy resin

Yuxuan Zhang,Shuang Liu,Shuo Yan,Yun Li,Jilin Cao

To address the environmental accumulation of large-scale titanium gypsum waste generated during the titanium dioxide production process and promote CO 2 capture and utilization, this study proposes an efficient integrated strategy involving the simultaneous utilization of titanium gypsum and CO 2 . Specifically, titanium gypsum is converted in situ into hydrophobic nano-calcium carbonate (HNCC) through CO 2 mineralization for use in the reinforcement of epoxy resin (EP). In the synthesis process, titanium gypsum is mixed with sodium stearate, sodium hydroxide, and polyvinylpyrrolidone (PVP) solution, followed by CO 2 bubbling. The effects of CO 2 injection time, sodium stearate content, PVP content, and solid-liquid ratio on the synthesis of HNCC are systematically investigated to determine the optimal process conditions. The resulting HNCC exhibits uniform dispersion, with an average particle size of approximately 70 nm and a contact angle of 152.8°, indicating superhydrophobicity. HNCC is applied to enhance the mechanical and thermal properties of EP. When the HNCC loading is 10 wt%, the tensile strength, elongation at break, bending strength, and bending strain of the composite increase by 72.64%, 58.48%, 26.32%, and 50.00%, respectively, compared to pure EP. Additionally, the glass transition temperature, crosslinking density, and char yield of the composite increase by approximately 10 °C, 72.15%, and 51.75%, respectively. This approach not only provides an efficient route for the valorization of titanium gypsum waste but also presents a promising strategy for CO 2 capture and utilization.

✓ 已验证 DOI 高影响因子
查看原文 查看 PubMed
JOURNAL OF HAZARDOUS MATERIALS · 2026 · IF 10.6

How to measure copresent ammonia and inorganic chloramines reliably: Some fundamental issues and novel solutions

Xiao Li,Longjie Cheng,Sen Lu,Yuheng Chen,Xiaoyu Tan,Bin Xu,Baiyang Chen

Ammonia (NH 4 + ) and chloramines often coexist in disinfected water, and accurate determination of their concentrations is important in understanding the status of treatment process. However, their measurements are prone to interference from each other and many operational variables. To select proper approaches, we assessed several representative methods commonly used for measuring NH 4 + , monochloramine (NH 2 Cl), and dichloramine (NHCl 2 ) in water dosed with varying molar ratios of free chlorine (FC) to NH 4 + (Cl 2 :N). Results indicate some fundamental issues that were overlooked before. For example, neither Nessler’s reagent method nor ion chromatography (IC) can analyze NH 4 + reliably when NH 2 Cl was present, because the reaction NH 4 + + OCl - ⇌ NH 2 Cl + H 2 O is reversible and whenever NH 4 + was depleted by its reaction with Nessler’s reagent, which is a rapid and reversible process, NH 2 Cl immediately reverts to NH 4 + . For the same reason, quantifying FC using N, N-diethyl-p-phenylenediamine (DPD) reagent was also problematic, because NH 2 Cl spontaneously converts into FC whenever FC was consumed by its reaction with DPD reagent, which is also rapid and irreversible. Moreover, copresent NHCl 2 was able to interfere with the analysis of NH 2 Cl by the Indophenol reagent method, because NHCl 2 can partially become NH 2 Cl under strongly alkaline condition, which is required for the Indophenol method. To address these issues, we propose to estimate NH 4 + as the difference between total negative three valent inorganic nitrogen (TIN(-3)) and chloramines. Liquid chromatography (LC) appears to be a suitable method for chloramine analysis because it is derivatization-free and exhibits strong resistance to interferences, although its minimum detection limits (MDLs) could be further optimized. The proposed methods demonstrated superior reasonableness over conventional methods in both synthetic and real samples, and agreed better with the theoretical estimations. These methods might help not only reveal hidden information but also rectify misleading information in the ammoniacal chlorination system in the future.

CAS / MDL: 67-56-1
✓ 已验证 产品关联 DOI 高影响因子
查看原文 查看 PubMed
PHYSICAL CHEMISTRY CHEMICAL PHYSICS · 2026 · IF 3

Controlled hydrothermal growth of uniform rutile TiO 2 nanorod arrays for memristive applications

Zhiyuan Wang,Xiaohe Zhang,Yong Yang,Xiaobin Zhong,Suping Jia,Zongsheng Zhang,Yuan Gao,Junjie Guo,Xiaoping Han

Synthesis of highly uniform rutile TiO 2 nanorod arrays has long been a priority for fabricating the high-performance memristors, given its great potential as active-layer materials in memristive devices. Herein, a controllable hydrothermal synthesis of highly uniform rutile TiO 2 nanorod arrays on fluorine-doped tin oxide (FTO) substrates is presented. Through systematic investigations, it is revealed that the highly uniform rutile TiO 2 nanorod arrays are obtained via a 3-hour hydrothermal synthesis at 160 °C on vertical FTO substrates, postannealing at 450 °C for 1 hour, followed by 25-minute ultraviolet (UV) irradiation. The obtained TiO 2 nanorod arrays exhibit excellent substrate adhesion and pinhole-free morphology, with well-defined nanorod dimensions (an average diameter of 171 nm and a length of 2.44 μm) and high crystallinity (an average crystallite size of 16.66 nm). Using such nanorod arrays as the active layers, the Ag/TiO 2 /FTO memristive devices demonstrate remarkable resistive switching characteristics: (i) the ratio of high resistance state (HRS) and low resistance state (LRS) reaches 17.7, and (ii) the retention time is predicted to be more than 10 years. Current-voltage analysis indicates that the resistive switching behavior follows a synergistic combination of ohmic conduction and space-charge-limited current (SCLC) mechanisms. The current work offers valuable guidelines for structure-property optimization in highly uniform rutile TiO 2 nanorod array films, demonstrating their promising applications in high-performance memristive devices.

CAS / MDL: 546-68-9
✓ 已验证 产品关联 DOI PubMed 高影响因子
查看原文 查看 PubMed
INFRARED PHYSICS & TECHNOLOGY · 2026 · IF 3.8

A dual-functional composite film with high thermal conductivity and infrared emissivity for passive thermal management

Xiying Huang,Yue Su,Chuantong Cheng,Xu Zhang,Fang Yuan,Yikang Zhang,Mengyu Dong,Junqiang Zhang,Huijuan Niu

Radiative cooling (RC) technology has attracted significant attention for enabling passive heat dissipation without energy consumption. However, the low thermal conductivity of polymer-based materials poses significant challenges to their practical application in devices with internal heat sources. To address this issue, we developed a dual-functional composite film by embedding a three-dimensional porous copper foam skeleton into a TiO 2 /SiO 2 -filled polydimethylsiloxane (PDMS) matrix. The as-fabricated composite film exhibits a high thermal conductivity of up to ∼ 6.70 W m −1 K −1 while maintaining a high average emissivity( ε ¯ 8-13μm ) of ∼ 0.91 within the atmospheric window (8‒13 µm). Simulated heat dissipation testing revealed that, under nocturnal simulated heat source conditions, the 60 PPI composite film achieved a temperature reduction of approximately 4.16 °C compared to traditional radiative cooling materials. This synergistic design overcomes the critical thermal bottleneck of conventional RC materials, providing a promising pathway for the passive thermal management of high-power-density electronic devices.

CAS / MDL: 25322-68-3
✓ 已验证 产品关联 DOI 高影响因子
查看原文 查看 PubMed
JOURNAL OF ALLOYS AND COMPOUNDS · 2026 · IF 6.7

Mechanism exploration of abnormal dual luminescence in Mn2+-doped NaZr2(PO4)3 phosphate phosphors and their prospective anti-counterfeiting applications

Xiaokun Li,Jiejun Ren,Lina Chen,Xianbao Duan,Zhanhui Zhang

Mn 2+ -doped dual-emission luminescent materials have recently attracted significant interest. However, the distribution of Mn 2+ ions is highly dependent on the host crystal structure, the lattice sites, and the doping concentration. How to analyze and clarify the dual-emission mechanism of Mn 2+ has become a major challenge; thus, this work synthesized NaZr 2 (PO 4 ) 3 : Mn 2+ phosphate phosphors and systematically investigated their doping behavior and luminescence mechanisms. The synthesized NaZr 2 (PO 4 ) 3 : Mn 2+ phosphate phosphors exhibited dual broadband emission centered at 480 nm and 565 nm, respectively. Density functional theory (DFT) calculations confirmed the existence of different Mn doping configurations and their corresponding formation energies. The results revealed that at low concentrations, the Mn ions (Mn1) preferentially substitute Na sites; while at high concentrations, the later Mn ions (Mn2) substitutes Zr sites and interact with pre-existing Mn1 to form Mn-Mn dimer. Notably, the emission spectra of the phosphors were sensitive to both Mn 2+ doping concentration and excitation wavelength. The Commission Internationale de l′Éclairage (CIE) chromaticity coordinates could be tuned within the range of (0.2463, 0.3478) to (0.4128, 0.4733), enabling adjustable luminescence from cyan to yellow. Furthermore, leveraging the dual-wavelength emission and high contrast characteristics of this phosphor, we fabricated an anti-counterfeiting dot matrix displaying the information "WIT" via ASCII code and achieved clear fingerprint visualization. This work clarifies the doping site preference of Mn 2+ and the underlying mechanism of dual luminescence, paving the way for the applications of transition metal phosphors in fields such as information encryption and fingerprint visualization.

✓ 已验证 产品关联 DOI 高影响因子
查看原文 查看 PubMed
Journal of Environmental Chemical Engineering · 2026 ·Vol. 14 ·期 2 ·122015 · IF 7.5

Visible light-based photocatalytic ozonation of DCF over CQDs/FeTiO3 heterostructure in a spinning disk photocatalytic reactor

A. Al-Farraji,Saad H. Ammar,Hanan H. Abed,Zaid H. Jabbar

Photocatalytic ozonation is an advanced oxidation process (AOP) that has recently demonstrated its strong oxidation capabilities for efficient wastewater treatment using sunlight and air as the ozone source. Additionally, the spinning disc photocatalytic reactor (SDPR) has been widely adopted recently as an intensification approach for photocatalytic processes. Herein, an efficient approach has been adopted to enhance the degradation performance of photocatalytic ozonation process over CQDs/FeTiO 3 photocatalyst film in a SDPR for synergistically enhancing the degradation of diclofenac sodium (DCF). The DCF degradations were compared in different treatment systems in the SDPR, including ozonation, catalytic-ozonation, photocatalysis, and photocatalytic ozonation. High photocatalytic ozonation performance (99.3% degradation efficiency, 85.8% mineralization, and high stability after six runs) has been acquired over CQDs/FeTiO 3 photocatalyst film under visible-light exposure. The effective separation of photogenerated charge carriers due to CQDs deposition, and high generation of ORS resulting from the combined systems were responsible for the enhanced photocatalytic performance.

CAS / MDL: 60-00-4 75-65-0 79-06-1
✓ 已验证 产品关联 DOI 高影响因子
查看原文 查看 PubMed
Environmental Science-Processes & Impacts · 2026 · IF 4.2

Antibiotic toxicity screening on seedling emergence: beyond traditional species

R. Silvana Cortés-Lagunes,Andrea-Lorena Garduño-Jiménez,Wenshi Bao,Juan Carlos Durán-Álvarez,Felicity C. T. Elder,Joshua Greenwood,John H. Nightingale,Fan Zhang,Laura J. Carter

Antibiotics are prevalent environmental pollutants with documented plant uptake and effects. Germination and seedling emergence are critical stages of plant development, making toxicity tests valuable for assessing the terrestrial risk. This study aims to address the need to understand species and antibiotic-dependent effects of 10 antibiotics across 23 plant species, including non-cultivated and geographically diverse species, through a Tier I phytotoxicity screening in which all antibiotics were tested at a single nominal concentration of 1 mg L−1, an upper-bound environmentally relevant scenario. Results revealed that antibiotic toxicity is highly species and antibiotic-dependent, highlighting the need to evaluate effects on under-studied species. Some global trends were observed; fluoroquinolones (ciprofloxacin, enrofloxacin, ofloxacin) stimulated germination and root growth in legumes and grasses, while black knapweed (Centaurea nigra) consistently exhibits germination reductions (30–53%) and root growth inhibition under all antibiotic exposures. Florfenicol exposure decreased root length and biomass in Chinese cabbage (Brassica rapa subs. Pekinensis) by nearly 100%, contrasting with stimulation observed in rice (Oryza sativa). The importance of assessing sublethal effects, as root and biomass changes, in addition to germination, for a more comprehensive phytotoxicity assessment is demonstrated. Standardized test conditions may overlook species requiring specific germination conditions. Sorption of antibiotics to filter paper affected exposure concentrations, emphasizing the importance of chemical quantification before and after tests. This study highlights the need for adaptive phytotoxicity protocols, careful experimental design to obtain statistically significant results, and inclusion of non-cultivated species as bioindicators to better assess antibiotic risks to terrestrial plants.

CAS / MDL: 67-56-1
✓ 已验证 产品关联 DOI PubMed 高影响因子
查看原文 查看 PubMed
SURFACE & COATINGS TECHNOLOGY · 2026 · IF 6.9

Fluorine-free photothermal superhydrophobic composite coating for efficient anti-icing of wind turbine blades

Xiang Kong,Bingxu Wang,Lin Xia,Mingming Liu,Peng Zhang,Haipeng Wang,Xuemei Huang,Leian Zhang,Jun Ma

Ice accretion severely compromises wind turbine efficiency. Herein, a fluorine-free photothermal superhydrophobic coating (FPSC) was fabricated via scalable spraying of MWCNTs-OH and TiN. The coating exhibited a water contact angle of 159.0 ± 2.5° and a low roll-off angle of 3.4 ± 0.3°, ensuring excellent water repellency and self-cleaning durability. Benefiting from the elevated nucleation energy barrier induced by its hierarchical micro/nanostructure, the FPSC significantly prolonged the droplet freezing process, achieving freezing times of 3907 ± 20 s, 1357 ± 15 s, 959 ± 13 s, and 731 ± 10 s at −5, −10, −15, and −20 °C, respectively. Furthermore, owing to strong solar absorption, the coating maintained stable performance over 40 photothermal cycles under 1 sun irradiation even after mud-contaminant removal, and melted frost and ice within 108 s and 255 s, respectively, under 1.5 sun irradiation. On a blade model, it achieved >99% initial anti-icing efficiency. Notably, a theoretical assessment accounting for environmental performance degradation indicates that the FPSC can recover approximately 487.3 h of annual operational downtime in Northeast China, corresponding to a recovery of 11.1% of annual energy production loss. Consequently, it is projected to contribute an additional 122.2 TWh generation gain by 2025. This scalable FPSC provides a robust, economically viable anti-icing solution.

CAS / MDL: 16415-12-6
✓ 已验证 产品关联 DOI 高影响因子
查看原文 查看 PubMed
CERAMICS INTERNATIONAL · 2026 · IF 6

Aqueous gel casting ceramic substrates with tailored microstructure and dielectric properties for patch antenna applications

Zhipeng Lu,Qing Yao

The advancement of 5G microwave technology creates increasing demand for compact, versatile devices capable of operating across various scenarios, which has driven the development of dielectric patch antennas. These innovative antennas successfully combine several key advantages: compact physical dimensions, lightweight construction, low-profile form factor, and extremely low dielectric loss - all while maintaining cost efficiency, enabling seamless integration with active components, and simplifying the packaging process. The ceramic substrate plays an absolutely essential role in it. In this study, MgTiO 3 -CaTiO 3 (MCT) ceramic substrates were prepared specifically for microstrip antenna applications using an aqueous gel casting technique. These substrates were then systematically compared with alternatives manufactured through conventional dry pressing methods. To optimize the key parameters, the process entailed a comprehensive analysis of multiple factors: the rheological behavior of the slurry at various solid loadings, the microstructural features obtained, and the dielectric properties across different sintering temperatures. Special attention was given to controlling the heating rate to prevent substrate deformation. The optimized MCT substrates demonstrated exceptional performance, achieving a quality factor ( Q×f ) of 74,213 GHz, a 6% improvement over dry-pressed samples, while simultaneously allowing a 45 °C reduction in sintering temperature. A MCT microstrip antenna was fabricated operating at 2.4 GHz. Electromagnetic simulation results showed its peak far-field gain was about 1.5 times greater than that of conventional FR4-based antennas. These findings conclusively demonstrated the practical effectiveness of aqueous epoxy systems for developing high-performance microstrip patch antennas (MPA) using MCT ceramic materials.

✓ 已验证 DOI 高影响因子
查看原文 查看 PubMed
Materials Today Chemistry · 2026 · IF 7.4

On designing percolation proton conductors: A case study of (Sr,La)(Zr,Y)O2.95

Jin Chen,Naoyuki Hatada,Wenhao Li,Wenzhuo Chen,Donglin Han

Heavily acceptor-doped perovskite oxides have the potential to activate percolation conduction of protons at reduced temperatures, and the reported percolation proton conductors up to now are restricted to the systems containing high Sc content. However, larger trivalent rare earth elements (e.g., Y) are known to be better dopants for proton conducting zirconates, but their solubility is low. In this work, we propose a new strategy to design the percolation proton conducting perovskites, by introducing La and Y into the Sr and Zr-sites of SrZrO 3 , respectively, leading to the formation of (Sr 1.1- x La x -0.1 )(Zr 1- x Y x )O 2.95 (SLZY, x  = 0.1 – 1.0), which takes Pnma and Pna 2 1 orthorhombic structures with x  = 0.1 – 0.4 and 0.5 – 1.0, respectively. Interestingly, the conductivity decreases with the Y content increasing from 0.1 to around 0.7 and increases with the Y content further increasing to 1.0. Moreover, the activation energy of the bulk conduction shows the maximum value at x  = 0.6. In addition to the expected monotonically increasing activation energy resulted from the enhanced structural asymmetry, these results imply that the trapping effect of protons plays an important role, which is enhanced with Y content increasing from 0.1 to around 0.6. Notably, higher Y content (e.g., x  > 0.6) appears to activate the percolation conduction of protons, leading to the decreasing activation energy.

CAS / MDL: 1312-81-8 1633-05-2
✓ 已验证 产品关联 DOI 高影响因子
查看原文 查看 PubMed
JOURNAL OF RARE EARTHS · 2026 · IF 9.6

Cr3+ to Ln3+ energy transfer unlocks ultra-efficient NIR emission in Cs2NaLuCl6 single crystals

Youwang Long,Lei Zhong,Yuefei Xiang,Yunhai Zhu,Zaidong Chen,Yuanqing Kang,Lei Zhou,Mingmei Wu

Developing efficient near-infrared (NIR) luminescence materials is crucial for next-generation NIR phosphor-converted light-emitting diodes (pc-LEDs). Cr 3+ -activated materials exhibit broadband NIR emission, however, they suffer from low efficiency and severe thermal quenching at wavelengths beyond 900 nm. To overcome these drawbacknd Membrane Technology, School of Chemical Engineering and Technology, Sun Yat-sen Uns, an efficient energy transfer pathway from Cr 3+ to Ln 3+ (Yb 3+ , Tm 3+ ) in Cs 2 NaLuCl 6 (CNLC) double perovskite single crystals was established. The Cr 3+ singly doped crystal shows broadband NIR emission peaking at 970 nm with an internal quantum efficiency (IQE) of 73.1%. Through effective Cr 3+ sensitization, the NIR-II emissions at 996 nm (Yb 3+ ) and 1222 nm (Tm 3+ ) are enhanced, along with the significantly improved luminescent thermal stability. Moreover, the co-doped system also exhibits superior IQE of 86.6% for CNLC:3 mol%Cr 3+ ,9 mol%Yb 3+ and 71.6% for CNLC:3 mol%Cr 3+ ,5 mol%Tm 3+ . The developed crystals integrated into a 540 nm-driven NIR LED delivers a NIR radiation power of 80.4 mW at a driving current of 600 mA, enabling high-resolution bioimaging and night vision applications. This work provides insight into energy transfer engineering to boost the luminescent efficiency and thermal stability in NIR-emitting materials.

✓ 已验证 产品关联 DOI 高影响因子
查看原文 查看 PubMed
JOURNAL OF ALLOYS AND COMPOUNDS · 2026 · IF 6.7

Self−supported Ni3S2 nanoarrays as multi−functional catalysts for efficient alkaline water and seawater electrolysis

Bo Zhao,Zengyuan Fan,Xiaohong Zhang,Ying Zhang,Yunpeng Wu,Yining Wang,Hao Sun,Jiawei Wang

The development of efficient non−precious metal catalysts is of critical importance for advancing water splitting technology. Through rational morphological engineering, key parameters such as specific surface area, the density of exposed active sites, and mass transport pathways can be simultaneously optimized, thereby directly enhancing reaction kinetics. In this study, self−supported Ni 3 S 2 nanoarrays were synthesized via a sequential pretreatment and sulfidation strategy, utilizing nickel foam as both the nickel source and the growth substrate. The resulting nanoarray structure proved to be an efficient and durable electrocatalyst for water splitting. In 1.0 M KOH solution, the overpotential of the HER (69 mV) approaches that of Pt/C, whilst the OER overpotential (199 mV) outperforms RuO 2 , yielding an overall water splitting voltage of 1.54 V (10 mA cm −2 ). The same excellent catalytic activity was also exhibited in simulated seawater with overpotentials of 98 and 225 mV for HER and OER, respectively. The main reason for the enhanced catalyst activity is attributed to the unique nanoarray morphology that exposes a larger electrochemically active specific surface area and provides abundant active sites. More importantly, there is a strong coupling between nickel foam substrate and Ni 3 S 2 nanoarrays catalyst. The strong Ni−S chemical bond formed during the hydrothermal preparation much improves the catalytic activity, electronic conductivity and structural stability.

✓ 已验证 产品关联 DOI 高影响因子
查看原文 查看 PubMed
已复制

文献关联基于可获得的产品、CAS、DOI 及引用记录。收录不代表作者或出版方对阿拉丁产品的背书,请以原始文献为准。