COMPOSITES PART B-ENGINEERING
·
2026
·
IF 14
Meiying Ge,Haopeng Wang,Lixin Wu,Longhui Zheng,Jia-Tao Miao
Triboelectric nanogenerators (TENGs) hold substantial potential in the fields of clean energy. However, the synergistic optimization of environmental friendliness, high performance, and processability for their triboelectric layer materials remains a challenge. Herein, a biobased epoxy monomer (BMOPM) was designed and synthesized using lignin-derived creosol as the renewable feedstock, and cured by a disulfide bond-containing curing agent 4-aminophenyl disulfide (APDS) to construct a dynamically crosslinked epoxy resin (BMOPM/APDS). While maintaining high mechanical strength, BMOPM/APDS possessed a relatively low crosslinking density, which provides sufficient space for disulfide bond exchange and thus enables efficient reprocessing. Notably, the reprocessed resin maintained 92% of its original flexural strength. Leveraging the biomass-derived feature and reprocessability of BMOPM/APDS, a green triboelectric nanogenerator (BA-TENG) was successfully fabricated into an integrated structure via hot-press welding of the triboelectric layer BMOPM/APDS resin and conductive layer BMOPM/APDS/CNTs composite. This eco-friendly fabrication strategy not only achieves environmental sustainability for the device but also greatly simplifies the manufacturing process while significantly enhancing the structural stability of the integrated BA-TENG. BA-TENG exhibits considerable electrical output performance and cycling stability during 7500 cycles. Furthermore, BA-TENG could light up LED arrays and charge capacitors to power electronic devices. This research provides a novel strategy for the design of biobased high-performance epoxy resins and their composites as well as the integrated preparation of green TENGs.
✓ 已验证
产品关联
DOI
高影响因子
ANALYTICA CHIMICA ACTA
·
2026
·
IF 6.1
Tongfei Gao,Zhuangzhuang Dong,Jianhua Xiong,Hongxia Hao,Xiantao Shen,Wenge Tang,Zhen Tong,Chuixiu Huang
The widespread abuse of amphetamine-type stimulants (ATS) poses severe threats to public security and health, necessitating rapid and accurate on-site detection of ATS specially at crime scenes for criminal detection and illicit drug control. However, detection of complex samples at crime scenes by surface-enhanced Raman scattering (SERS) is still a challenge because of the matrix effect. Flat membrane-based liquid-phase microextraction (FM-LPME) enables efficient separation and sufficient sample clean-up. FM-LPME was used to overcome the matrix effect on SERS, and a sensing platform of FM-LPME-SERS was developed for rapid and accurate detection of ATS. The effect of key operation factors on FM-LPME performance was investigated. ENB and NPOE were identified as efficient supported liquid membrane solvent. For SERS, silver nanoparticles synthesized by sodium citrate reduction displayed superior enhancement in SERS signal, and the SERS signal for ATS could be further improved by sodium bromide. Finally, a quantitative model based on partial least squares regression was established to analyze the FM-LPME-SERS sensing data, which displayed satisfactory analytical performance for blood spot, urine, and wastewater samples with acceptable detection limit (0.011-0.570 μg mL -1 ), high repeatability (RSD ≤ 13%), and satisfactory accuracy (90-114%). This method was successfully applied to analyze wastewater samples from a drug production site provided by the Public Security Bureau in XX Province. Therefore, FM-LPME-SERS is a powerful tool for on-site detecting ATS in complex samples, which is of great importance for forensic science and public security. We believe this work will expand the applicability of SERS for complex samples.
✓ 已验证
产品关联
DOI
PubMed
高影响因子
INTERNATIONAL JOURNAL OF BIOLOGICAL MACROMOLECULES
·
2026
·
IF 8.7
Jianfu Qiao,Biyang Ling,Xiangyi Han,Hong Gu,Qi Wang
Full-thickness skin defects present substantial clinical challenges owing to the complete disruption of normal tissue architecture, elevated susceptibility to microbial infection, and the inherently limited regenerative capacity of damaged skin. Accordingly, the development of injectable biomaterials that integrate antibacterial activity with regenerative functionality is essential for facilitating efficient skin repair. This study presents an environmentally friendly strategy for the construction of a silver nanoparticle-incorporated carrageenan–hyaluronic acid composite antibacterial hydrogel intended for full-thickness skin wound repair. Under visible light, silver ions simultaneously participate in the cross-linking reaction of carrageenan and are reduced to uniformly dispersed silver nanoparticles, thereby endowing the hydrogel with a stable structure and antibacterial activity without the need for exogenous cross-linking agents and chemical reducing agents. The resulting hydrogel exhibited good injectability, high water content, biocompatibility, and biodegradability, and had a broad-spectrum antibacterial effect against both Gram-positive and Gram-negative bacteria. In vitro experiments demonstrated that the hydrogel exhibited excellent cytocompatibility and significantly enhanced cellular activity. Moreover, evaluation in animal models of full-thickness skin defects confirmed that the injectable carrageenan–hyaluronic acid–silver nanohydrogel effectively accelerated wound closure within 14 days. This environmentally friendly, antibacterial polysaccharide-based hydrogel offers a novel strategy for the design of injectable wound dressings and shows promising application prospects in skin wound repair and regenerative medicine.
✓ 已验证
产品关联
DOI
PubMed
高影响因子
Nature Communications
·
2026
·
IF 18.1
Topatana Win,Sun Yuchao,Xie Tianao,Zhu Yiyuan,Yang Taorui,Shen Ruijing,Ran Peng,Li Chengao,Chen Jiadong,Shen Xuqiu,Lu Ziyi,Han Yina,Shan Yukai,Li Shijie,Chen Tianen,Cai Xiujun,Deng Renren,Juengpanich Sarun,Chen Mingyu
Persistent luminescence is a promising approach for photodynamic therapy (PDT) in deep-seated tumors, as it provides sustained light within tissues, eliminating the need for continuous external illumination. However, the uncontrollability of light within the body complicates precise spatiotemporal regulation. In this study, we report X-ray preactivated elimusertib-loaded tumor-targeted photodynamic nanoparticles (ETPNs), featuring reversible “on-off” afterglow properties. The excellent afterglow properties of X-ray-activated porous NaYF 4 :Er@NaGdF 4 persistent luminescence nanoparticles enable the continuous activation of chlorin e6 (Ce6) to generate reactive oxygen species (ROS), leading to DNA damage. The integration of elimusertib potentiates ROS-induced DNA damage and activates the cGAS-STING pathway, thereby enhancing immuno-photodynamic therapeutic efficacy. All in vivo experiments were conducted using female mice. Our findings highlight the potential of ETPNs to advance the therapeutic landscape for deep-seated tumors, offering a robust and controllable platform for combined immuno-photodynamic therapy.
✓ 已验证
产品关联
DOI
PubMed
高影响因子
JOURNAL OF COLLOID AND INTERFACE SCIENCE
·
2026
·
IF 9.6
Hua Wei,Liya Zhang,Ke Wang,Tongkun Guo,Yue Liu,Yaqing Liu,Jingcheng Hao
Hypothesis Real-time and accurate glucose detection is essential for healthcare management. Conventional enzymatic sensors are often limited by instability and complex fabrication, while non-enzymatic alternatives often lack sufficient selectivity. Experiments We develop a novel field-effect transistor biosensor (bio-FET) integrated with a thermo-responsive hydrogel for enzyme-free glucose sensing. The hydrogel is formed through in situ micellar self-assembly of phenylboronic acid-terminated Pluronic F127 copolymers (F127-PBA), exhibiting reversible sol-gel transition near physiological temperature. Serving as a conformal dielectric layer on the In 2 O 3 channels, the F127-PBA hydrogel film enables highly sensitive and selective glucose detection across a wide concentration range (100 nM to 1 M). The sensing mechanism relies on the charge state shift of PBA groups upon glucose binding, transducing biochemical signals into measurable electrical responses with high stability and reproducibility. Findings This work may provide a versatile and scalable strategy for constructing high-performance FET biosensors in real-time glucose detection.
✓ 已验证
产品关联
DOI
PubMed
高影响因子
SEPARATION AND PURIFICATION TECHNOLOGY
·
2026
·
IF 9.1
Yujie Chai,Fupeng Li,Huawei Shi,Junjun Cao,Shuai Wang,Yan Wang,Gaohui Liu,Ruiyan Xiong,Junqi Gan,Chuanjie Fang,Liping Zhu
Haloacetic acids (HAAs), a class of disinfection by-products (DBPs) commonly found in potable water, pose significant risks to human health. It is challenging for conventional membrane filtration technologies to efficiently remove HAAs from water due to their small molecular sizes, as size-sieving effects often dominate the separation process. In this work, a nanofibrous membrane was developed for the rapid and effective adsorptive removal of HAAs from water. A two-step intensified strategy was employed to fabricate the adsorptive membrane: polyethyleneimine (PEI) was incorporated during electrospinning to provide abundant amine-based adsorption sites, followed by a co-deposition process involving PEI and dopamine (DA) to enhance interfacial contact between water and the membrane. The resulting membrane exhibited a high specific surface area, significant porosity, and improved hydrophilicity, all of which contributed to its strong adsorption capacity for HAAs. As a result, the membrane demonstrated an exceptional water flux of up to 260 L·h −1 ·m −2 under a 2.5 cm water column, with dihaloacetic acids (DCAA) treating capacity of 36 mg·m −2 and a removal efficiency exceeding 93%. Furthermore, an adsorptive membrane module with an effective area of 0.27 m 2 was fabricated, achieving an ultrahigh treating capacity of 297 mg·m −2 for five HAAs, a removal efficiency exceeding 99%, and a water flux of 370 L·h −1 ·m −2 ·bar −1 —two orders of magnitude higher than that of conventional membranes. This work presents a simple yet highly effective strategy for the enhanced removal of DBPs, highlighting its strong potential for practical applications in drinking water purification.
✓ 已验证
产品关联
DOI
高影响因子
COLLOIDS AND SURFACES A-PHYSICOCHEMICAL AND ENGINEERING ASPECTS
·
2026
·
IF 5.4
Yang Gao,Xian Du,Zhuo Li,Lihan Wang,Bo Tian,Ruixue Tian,Huiling Du
With the development of industry, large quantities of volatile organic compounds (VOCs) not only cause damage to the ecological environment, but also pose a serious threat to human health. At present, most photocatalysts used for benzene treatment still suffer from problems such as narrow light absorption range, high electron-hole recombination rate, and low charge transfer efficiency. Therefore, the development of high-performance photocatalysts is extremely urgent. The introduction of oxygen vacancies and the construction of heterojunctions can effectively solve the above problems. In this study, a defect-rich photocatalyst was combined with a topology-structured metal-organic framework (MOF) to construct a tightly coupled heterojunction, aiming to address these issues and improve the photocatalytic degradation performance of benzene. By introducing oxygen vacancy-rich TiO₂ nanosheets into NH₂-MIL-125, a tightly coupled Z-scheme heterojunction composite photocatalyst is fabricated. The benzene degradation efficiency of the composite reaches up to 98.5%, which is 1.47 times and 1.27 times that of pure NH₂-MIL-125 and oxygen vacancy-rich TiO₂, respectively, while also exhibiting remarkable stability and high adsorption capacity. Oxygen vacancies act as active sites that strengthen the interfacial electronic interaction of the composite, thereby optimizing the electron transport pathway of the heterojunction and improving the carrier separation efficiency. Under the dual modulation of the heterojunction and oxygen vacancies, the built-in electric field is further intensified, leading to a significant enhancement in the adsorption and catalytic performance of the composite. This study provides an effective design strategy for utilizing oxygen vacancy-driven heterojunctions in catalysts for the efficient abatement of VOCs.
✓ 已验证
产品关联
DOI
高影响因子
BIOCHEMICAL ENGINEERING JOURNAL
·
2026
·
IF 3.6
Xinyue Wang,Haojie Qian,Caoxing Huang,Bo Fan,Yucai He,Wei Tang
This work successfully developed an alkaline deep eutectic solvent (DES) composed of cetyltrimethylammonium bromide (CTAB) and ethanolamine (EA), and systematically evaluated its performance in the pretreatment of poplar sawdust (PS). The characterization of DES indicated an extensive hydrogen-bonding network and exceptional thermal resilience. Through optimization of key pretreatment parameters, the most effective pretreatment conditions were determined to be a molar ratio of CTAB to EA at 1:8, a temperature of 160 °C, and a time of 90 min. Under these optimized conditions, the DES demonstrated remarkable fractionation performance, achieving efficient delignification (64.2%) and substantial xylan extraction (92.4%). Ultimately, the enzymatic hydrolysis achieved an exceptional efficiency of 83.9%. Structural analyses unveiled that the pretreatment profoundly amplified substrate accessibility and elevated the crystallinity index of cellulose, while simultaneously achieving efficient cleavage of pivotal interunit linkages and aromatic frameworks embedded within lignin. The dominant mechanism underpinning enhanced efficiency centered on the disruption of lignin-driven supramolecular aggregation and the potentiation of intermolecular hydrogen bonding networks, thereby enabling a more thorough and effective disassembly of the lignocellulosic architecture. This remarkable enhancement in saccharification performance not only established a robust sugar platform for ethanol fermentation from PS but also delivered profound theoretical insights and critical technological advancements for the realization of high-value biorefinery systems leveraging other hardwood feedstocks.
✓ 已验证
产品关联
DOI
高影响因子
MICROCHEMICAL JOURNAL
·
2026
·
IF 5.2
Zhenting Zhao,Wenhong Shen,Guoqiang Yang,Haijuan Mei,Kai Li,Ke Li,Yang Lai,Ting Wang,Junfeng Zhao,Qiuyue Gui,Jie Hu,Weiping Gong
Accurate monitoring of blood glucose concentration is crucial for diabetes diagnosis. In this work, a three-dimensional hierarchical structure was fabricated by incorporating CoCu-layered double hydroxide onto flexible carbon foam (CoCu-LDH/FCF). Its porous, sponge-like architecture provides a high specific surface area and exposes abundant catalytic sites, thereby enhancing electrocatalytic performance for glucose sensing. The CoCu-LDH/FCF composite was immobilized onto a screen-printed electrode (SPE) to construct a portable sensor, designated as CoCu-LDH/FCF/SPE. The resulting sensor exhibits excellent electrocatalytic activity toward glucose oxidation, featuring a linear detection range of 2–500 μM, a sensitivity of 25.6 μA·μM −1 ·cm −2 , favorable selectivity, and long-term stability. Furthermore, a portable detection platform was developed by integrating the sensor with a flexible electrochemical integration module and a smartphone. Experimental results demonstrate the high performance of the CoCu-LDH/FCF/SPE sensor within this compact system.
✓ 已验证
产品关联
DOI
高影响因子
SENSORS AND ACTUATORS B-CHEMICAL
·
2026
·
IF 8.3
Kun Zhang,Han Yan,Xiaoduo Chen,Zusen Chen,Xiaonan Feng,Ya Hu,Zheqian Chen,Xiaoyuan Guo,Chuanzi Gao,Yanzhou Bao,Jizhou Wu,Bintian Zhang
Cationic per- and polyfluoroalkyl substances (PFAS) are emerging environmental contaminants of growing concern, yet rapid and reliable sensing strategies remain scarce due to limited molecular selectivity and poor resistance to false-positive signals. Herein, we report a portable electrochemical sensor for perfluorooctane sulfonamide quaternary ammonium (PFOSAmS) based on a molecularly imprinted poly(4-hydroxybenzoic acid) membrane integrated onto a disposable screen-printed electrode. Molecular electrostatic potential analysis reveals strong anionic sites within the imprinted polymer that favor electrostatic attraction to the cationic headgroup of PFOSAmS, while the aromatic backbone provides hydrophobic domains complementary to the perfluorinated chain. The formation of imprinted cavities effectively enhances the selectivity for PFOSAmS over structurally related PFAS. Specific binding of PFOSAmS generates a dual electrochemical response, characterized by a decrease in probe current and a positive shift in redox potential, enabling intrinsic discrimination of false-positive signals. Nonspecific adsorption only reduces interfacial electron transfer without affecting the redox potential, whereas binding within the imprinted cavities disturbs the local electrostatic and dielectric environment, leading to a characteristic potential shift. Under optimized conditions, the sensor exhibits a detection range from 50 pM to 5 µM with a detection limit of 7 pM (5.1 ng/L). Selectivity evaluation against 20 potential interferents, including seven representative PFAS, confirms negligible influence. Practical detection of PFOSAmS in tap, bottled, and river water samples further demonstrates the robustness of the sensing platform. This work establishes a rapid, low-cost, and false-positive-resilient analytical tool for sensitive and accurate detection of cationic PFAS.
✓ 已验证
产品关联
DOI
高影响因子
BIOCHEMICAL ENGINEERING JOURNAL
·
2026
·
IF 3.6
Wei Tang,Haojie Qian,Xinyue Wang,Jiajia Wang,Jiaming Zhang,Caoxing Huang,Bo Fan,Yucai He
Amino acid-based deep eutectic solvents (DES) have emerged as a quintessential class of alkaline DES, known for exceptional delignification in lignocellulose pretreatment under mild conditions, thereby enhanced the economic feasibility of biorefinery. This study introduces an innovative ternary DES comprised of cetyltrimethylammonium bromide (CTAB), ethanolamine (EA), and lysine (Lys), engineered for efficient pretreatment of poplar sawdust (PS). Results show that increased Lys concentration progressively reduces pH, conductivity, and polarity, while significantly enhancing hydrogen bond donor and acceptor capacities. The amino and carboxyl groups in Lys synergistically establish a robust three-dimensional hydrogen-bonded network. Specifically, DES pretreatment dramatically improves PS fractionation: compared with the Lys-free control, Lys introduction elevates lignin removal from 42.2% to 87.2%, and xylan removal from 78.5% to 99.9%, respectively. Meanwhile, cellulose digestibility increases from 65.5% to 96.0%, and ethanol yield rises from 56.3% to 89.9%. Structural characterization unveiled that Lys remarkably promoted selective cleavage of lignin linkages, thereby dismantling the lignin framework. This reorganization reduces lignin’s specific surface area, enhances cellulose exposure, and boosts enzymatic hydrolysis. Notably, the DES exhibits excellent recyclability. These findings highlight the great potential of alkaline DES for sustainable biorefining and valorization of forestry biomass residues.
✓ 已验证
产品关联
DOI
高影响因子
JOURNAL OF CATALYSIS
·
2026
·
IF 6
Xinping Duan,Jinlin Lu,Zhaojun Wen,Xuelian Liang,Haiqiang Lin,Linmin Ye,Youzhu Yuan
In supported metal catalysis, conventional strong metal-support interaction (SMSI) often leads to the encapsulation of active metal sites, thereby suppressing catalytic performance, for instance, nickel-based in thermocatalytic CO 2 hydrogenation. Here, we demonstrate that constructing a defective TiO x overlayer on anatase TiO 2 via room-temperature NaBH 4 treatment effectively transforms the classical SMSI state into a quasi-reactive metal-support interaction (quasi-RMSI) in Ni/TiO 2 -based catalysts. This pre-engineered interface, abundant in Ti 3+ and oxygen vacancies, prevents the formation of a dense TiO x encapsulation layer while facilitating electron transfer to Ni nanoparticles and promoting the activation of both CO 2 and H 2 . As a result, the Ni catalyst exhibits a one-order-of-magnitude increase in the CO 2 methanation rate with nearly 100% CH 4 selectivity, a 12-fold enhancement in turnover frequency, and exceptional long-term stability over 200 h. Combined spectroscopic and microscopic analyses reveal that the quasi-RMSI creates a highly active and accessible Ni-TiO x interface, which significantly accelerates CO 2 dissociation and sequential hydrogenation. This work establishes a general defect-engineering strategy for designing high-performance CO 2 methanation catalysts via tailored quasi-RMSI.
✓ 已验证
产品关联
DOI
高影响因子