文献检索

查找使用阿拉丁产品的科研文献

检索与阿拉丁产品相关的同行评审论文、DOI、PubMed 编号、期刊、作者、CAS 号及研究领域。

科研影响力快照

与阿拉丁产品相关的已发表科研成果

在搜索之前,这些指标可帮助访客快速了解产品关联科研的规模与质量。

347,389+ SCI 论文 与阿拉丁产品引用相关
2,303,681.05 总影响因子 匹配文献记录中影响因子的总和
81.20 最高期刊影响因子 匹配期刊中的最高 IF
6.63 平均期刊影响因子 匹配文献的平均 IF

参考指标 指标基于阿拉丁文献引用数据库及期刊影响因子记录。文献关联仅供科研参考,请以原始文献为准。

产品列表

视图 列表 网格

显示第2533至2544个,产品总数168,744个

切换升序
H*
IEEE Transactions on Components Packaging and Manufacturing Technology · 2026 · IF 3.3

Hot Press Sintering of Copper Particles: An Effective Approach for Low-Resistivity Repair of Open Defects in Precision Circuits

Changlong Ye,Dongchang Ma,Wenzhe Wang,Huitao Liu,Kang Wan,Junyi Lu,Guannan Yang,Yu Zhang,Guanghan Huang,Chengqiang Cui

In this work, we present a repair method of open circuit defects in precision circuitry using hot press sintering of copper particles followed by laser ablation. First, the open circuit defect position is filled with copper particle paste. Then, the copper particles are hot-press sintered to form conductive pathways. Finally, a high-power-density laser with a micron-sized beam spot is used to remove residual excess copper. With this method, open circuit defects with a length of 100 μm, a width of 100 μm, a line spacing of 80 μm, and a thickness of 45 μm can be successfully repaired. In contrast to the traditional circuit forming route that uses laser sintering of copper particles, the hot press sintering step promotes the closure of internal voids. As a result, a more compact sintered structure is obtained, and the formable circuit thickness, porosity, and electrical properties can be significantly improved. The as-repaired circuit region exhibits a low porosity of 14% and a low excess electrical resistance of 0.014 Ω, which corresponds to an electrical resistivity as low as 3.04 μΩ·cm. These results are significantly better than the circuit defects repaired by the laser sintering process, which results in an overall porosity of 45% and an electrical resistivity of 316.8 μΩ·cm. The circuit repair method presented here provides a promising technique for yield improvement and cost control for the manufacturing of precision circuits.

✓ 已验证 产品关联 DOI PubMed 高影响因子
查看原文 查看 PubMed
Innovative Food Science & Emerging Technologies · 2026 · IF 6.9

Coffee shell-derived carbon dot-chlorogenic acid nanoparticles with enhanced aPDT antibacterial activity for fish preservation during cold storage

Chenxiao Chen,Yiran Yang,Maha Alharbi,Ashwag Shami,Fahad Saad Alhodieb,Saleh A. Alsanie,Haiying Cui,Lin Lin

Chlorogenic acid-loaded coffee shell-derived carbon dot nanoparticles (CGA/CSCD NPs) with enhanced antibacterial photodynamic therapy (aPDT) activity were developed, exhibiting strong fluorescence (~400 nm), a graphite-like structure, and around 3 nm size. The nanoparticles achieved efficient ROS generation and bacterial enrichment, showing superior antibacterial efficacy and biocompatibility. Applied to Carassius auratus , Megalobrama amblycephala , and Dicentrarchus labrax under 4 °C storage, the CGA/CSCD NPs-aPDT treatment inhibited 99% of bacterial growth over 7 days, maintaining counts at 10 4 –10 5  CFU/g. The treatment significantly slowed pH rise, inhibited TVB-N accumulation, and reduced lipid oxidation by 2–3 times compared to controls. Furthermore, the nanoparticles preserved fish quality by minimizing moisture loss and maintaining color stability and texture (hardness and chewiness). These results demonstrate that CGA/CSCD NPs-aPDT provides a sustainable and effective strategy for delaying spoilage and extending the shelf life of aquatic products during cold storage.

✓ 已验证 产品关联 DOI 高影响因子
查看原文 查看 PubMed
INDUSTRIAL CROPS AND PRODUCTS · 2026 · IF 6.4

Valorization of Epimedium-derived icariin via magnetic MOF-immobilized naringinase: An efficient and reusable biocatalytic system for flavonoid modification

Haoyu Jia,Lingling Song,Tong Yan,Luran Wang,Jinyue Hu

Icariside I, a prenylated flavonol glycoside derived from Herba Epimedii , has attracted significant interest due to its enhanced bioavailability and pharmacological activities. Traditional methods for producing icariside I, including direct extraction and chemical hydrolysis of icariin, are limited by low yields, harsh conditions, and environmental issues. In this study, we developed a biocatalytic approach for the efficient conversion of icariin to icariside I using naringinase immobilized on magnetic metal-organic framework (MOF) nanoparticles (Nar@MOF) via EDC/NHS cross-linking. The Nar@MOF exhibited improved pH and thermal stability, as well as significant recyclability. Nar@MOF also demonstrated a lower K m value compared to the free enzyme, indicating enhanced substrate affinity. The biocatalyst enabled continuous icariside I production with 99.8% conversion and 98.3% yield within 4 h. Additionally, Nar@MOF maintained over 75% yield after ten consecutive cycles at 60 °C, highlighting its excellent stability and recyclability. Notably, Nar@MOF also exhibited broad substrate applicability. These results indicate that MOF-based immobilization offers a cost-effective and sustainable strategy for large-scale enzymatic conversion of icariin, with the magnetic MOF nanoparticles providing a versatile platform for high-value flavonoid production.

✓ 已验证 产品关联 DOI 高影响因子
查看原文 查看 PubMed
Journal of Energy Chemistry · 2026 · IF 15.6

Topotactic-templated conversion of ionic-cocrystal unlocking atomic-layered poly(heptazine imide) for Pt-assisted hydrogen photocatalysis

Liming Dai,Hua Wen,Rui Gao,Chenchen Fang,Jingyao Deng,Jinghong Wang,Ruixi Zhang,Lin Zhang,Yongsheng Fu,Li Shi,Xiaofei Yang,Jingwen Sun,Junwu Zhu

Poly(heptazine imide) (PHI) nanosheets hold great potential for photocatalytic hydrogen evolution due to their high crystallinity and extended π-conjugation, which enhance light absorption and charge transfer. However, conventional molten-salt synthesis only yields bulk PHI that fails to exploit these advantages. Here, we developed a cyanuric acid (CA)-LiCl ionic-cocrystal-mediated topotactic-templated conversion strategy to directly fabricate atomic-layered PHI (Li-PHIS). Structural characterizations reveal that the CA-LiCl cocrystal exhibits topological matching with Li-PHIS, where CA molecules form {00l}-oriented layer frameworks. The resulting Li-PHIS maintains crystallographically equivalent arrangement with heptazine ring constructing the {00l}-orientation. This topotactic-templated conversion strategy efficiently eliminates long-range diffusion, preserving the cocrystal’s layered framework. The Li-PHIS features a thickness of 3 ∼ 4 atomic layers with large specific surface area of 155.0 m 2 g -1 , which significantly facilitates active site exposure. Concurrently, reduced stacking density expands interlayer spacing, endowing a thermodynamically favorable band structure. Further in combination with the rapid charge migration dynamics provided by high crystallinity and Li + content in framework, Li-PHIS achieves a H 2 production rate of 4001 μmol h -1 g -1 with Pt-cocatalyst, surpassing bulk Li-PHI and C 3 N 4 by 3-fold and 40-fold, respectively. This cocrystal-mediated pathway provides a new paradigm for dimensionally controlled carbon nitrides and avoids irreversible structural damage from traditional exfoliation.

✓ 已验证 产品关联 DOI 高影响因子
查看原文 查看 PubMed
Cell Death & Disease · 2026 · IF 12.2

ZDHHC9 palmitoylates LAMTOR1 to promote renal cell carcinoma malignant progression

Liu Bo,Hou Tao,Liu Xizhi,Liu Lu,Ma Zhiqiang,Zhang Yujiao

The lysosomal regulator complex member LAMTOR1 serves as a crucial pivot that recruits the mechanistic target of rapamycin complex 1 (mTORC1) to the lysosomal surface, thereby influencing biological processes such as cell growth and cancer progression. In renal cell carcinoma (RCC), existing studies reveal that mTORC1 signaling contributes to cancer progression. However, the precise regulatory mechanisms underlying mTOR signaling in RCC remain unclear and warrant further investigation. Here, we demonstrate that the palmitoylation enzyme Zinc Finger DHHC-Type Containing 9 (ZDHHC9) activates the mTOR signaling pathway, thereby accelerating cancer progression and highlighting its potential role in RCC. In our study, we identified that ZDHHC9 specifically palmitoylates LAMTOR1 at its Cys3/4 residues, enhancing the recruitment of mTORC1 and subsequently activating the mTOR signaling cascade. Collectively, our findings provide novel insights into the pathogenesis of RCC and establish ZDHHC9 as a key mediator of RCC progression through the palmitoylation of LAMTOR1, which may serve as a promising target for the diagnosis and treatment of this malignancy.

CAS / MDL: 128-53-0 5470-11-1
✓ 已验证 产品关联 DOI PubMed 高影响因子
查看原文 查看 PubMed
Horticulturae · 2026 ·Vol. 12 ·期 2 · IF 3.4

Establishment of a Callus-Based Regeneration System for Lilium regale

Kang Luo,Liping Gao,Sisi Yang,Chao Song,Muhammad Sajjad,Hongjia Zhang,Yue Xu,Mingdong Ran,Huameng Huang,Yun Zheng

Induction of callus is an important step to produce high-quality seedlings, to promote the large-scale production of seedings, and to establish stable transgenic methods. To establish an efficient callus-based regeneration system for lily, in this study, we used the scales ofLilium regaleas explants and employed plant tissue thin-layer culture to induce callus tissues. To examine the effects of different types and concentrations of plant growth regulators (PGRs) on the induction of lily callus tissues and plant regeneration, we designed orthogonal experiments using three PGRs: 6-BA, NAA, and PIC, with each regulator at three concentration levels. The results indicated that a suitable medium for inducing callus under the experimental conditions was 1.00 mg/L 6-BA + 0.05 mg/L NAA + 2.00 mg/L PIC, pH = 5.8 because in this medium, callus tissue showed a good balance of induction and contamination rate, as well as very low redifferentiation into bulbs. Under the experimental conditions, a suitable medium for callus expansion was 1 mg/L 6-BA + 0.5 mg/L NAA, pH = 5.8. We also showed that the induced callus tissues could develop into seedlings. These findings provide important references for optimizing in vitro culture systems ofLilium regaleand offer supports for tissue culture studies of other lily species.

✓ 已验证 DOI 高影响因子
查看原文 查看 PubMed
Journal of Thermal Science · 2026 · IF 3.2

High-Performance SnTe-Graphite Composite Aerogels for Simultaneous Thermal Insulation and Thermoelectric Conversion

Hu Yang,Nie Yi’nan,Xin Nan,Li Yifei,Zhao Xin,Zhang Min,Tang Guihua

The simultaneous realization of efficient thermal insulation and waste heat harvesting remains a pivotal challenge in advanced thermal management and sustainable energy systems. Although thermoelectric aerogels offer a promising solution, their performance is traditionally constrained by the strong coupling among the Seebeck coefficient, electrical conductivity, and thermal conductivity. To overcome this limitation, this study demonstrates a synergistic strategy combining directional structural design with the incorporation of a high-Seebeck-coefficient thermoelectric phase. Using low-cost flake graphite as the conductive skeleton and SnTe as the active thermoelectric phase, SnTe-graphite composite aerogels (ST-GCAs) with highly anisotropic architectures were fabricated via directional freeze drying and carbonization. The results reveal that the anisotropic structure effectively decouples transport properties, endowing the material with high electrical conductivity parallel to the freezing direction and superior thermal insulation perpendicular to it. Notably, the incorporation of SnTe facilitates a transition from a metallic to a semiconducting transport mechanism, significantly enhancing the Seebeck coefficient. Consequently, the optimal sample maintains an ultra-low vertical thermal conductivity of 0.093 W·m −1 ·K −1 at room temperature, while achieving a Seebeck coefficient of 77.77 µV·K −1 and a ZT value of 0.02 at 973 K, representing an enhancement of approximately one order of magnitude (15.5 times) compared to the pristine GCA. This work provides a scalable route for developing lightweight, high-temperature-resistant composite materials capable of simultaneous high-efficiency thermal insulation and thermoelectric energy conversion.

CAS / MDL: 9004-62-0
✓ 已验证 产品关联 DOI 高影响因子
查看原文 查看 PubMed
Nature Communications · 2026 · IF 18.1

Self-polymerized polyphenol-based platform for the management of dry eye pathogenesis

Wang Zixin,Lv Zeen,Ge Yuxuan,Xue Ruiyang,Wu Fang,Han Haijie,Wang Yin

The management of ocular surface inflammation, particularly in conditions like dry eye disease (DED), remains challenging due to multiple pathogenic causes and ocular barriers. Traditional eye drops usually provide transient and partial symptom relief, necessitating combined therapies to break the vicious cycle of oxidative stress and inflammation. To surmount these limitations, a polyphenol-based eye drop is developed via the self-polymerization of rosmarinic acid in the presence of hyaluronic acid, followed by co-assembly with cerium ions to afford monodispersed RHC NPs. To enhance the ocular retention efficiency, thiol groups are further decorated on NPs (termed as s -RHC NPs). In two mouse models of DED, topical administration of s -RHC NPs leads to comprehensive relief of symptoms, including inflammatory response suppression, corneal epithelial defect repair, and tear secretion recovery. We envision that this work might facilitate the treatment of DED and inspire the design of polyphenol-based nanoparticles via a self-polymerization strategy.

✓ 已验证 产品关联 DOI PubMed 高影响因子
查看原文 查看 PubMed
Science Bulletin · 2026 · IF 20.7

Reinforced stepwise dissociation of water molecules via U 5f-O 2p-Ti 3d gradient orbital coupling for photoelectrochemical water splitting

Xiaochuan Deng,Tong Liu,Xudong Wu,Qijue Lin,Hanlin Liu,Han Yang,Xun Yang,Maoyin Wang,Kaiguo Chen,Jiayu Dai,Tao Chen,Wenkun Zhu

Actinide (An)-based materials have shown fascinating electronic and bonding properties related to f orbitals, demonstrating significant potential in catalysis. However, the catalytic utility of uranium is constrained by its low electron affinity and high reduction potential. In this study, we designed an asymmetric f-p-d gradient orbital coupling strategy through spatial engineering of the hybridization among U 5f, O 2p, and Ti 3d orbitals on TiO 2 nanorod arrays (U/TiO 2 NRA). This asymmetric 5f-2p-3d structure modulates the band structure to improve light absorption capacity and prolong the lifetime of charge carriers, while optimizing the adsorption energetics of reaction intermediates, thus enabling efficient stepwise water dissociation. The fabricated photoanode achieves a noteworthy photocurrent density and excellent operational stability, outperforming most reported TiO 2 -based catalysts. Through theoretical analyses, it is verified that the 5f buffer band at the asymmetric U−O−Ti sites, mediated by 5f-2p-3d gradient orbital coupling, facilitates electron transfer, which effectively promotes the adsorption, activation, and stepwise dissociation of water molecules at the dual atomic sites. In this work, a new design paradigm is established for the development of high-performance An-based catalytic materials.

✓ 已验证 产品关联 DOI PubMed 高影响因子
查看原文 查看 PubMed
JOURNAL OF ALLOYS AND COMPOUNDS · 2026 · IF 6.7

Preparation of polyimide-based composite aerogel for enhanced microwave absorption and thermal insulation

Le Chen,Lingling Tang,Haokun Geng,Qinghong Kong,Huimin Sun,Mingyi Chen,Wang Zhan

A lightweight, multifunctional polyamide acid (PAA)/carbonyl iron powder (CIP) composite aerogel with integrated thermal insulation and microwave absorption capabilities is developed via multi-structure design. With polydopamine (PDA) modified melamine foam (MF), this study achieves uniform dispersion of CIP and robust interfacial bonding. The results demonstrate that the PDA modification time and PAA content have a significant effect on the properties of composite aerogels. The composite aerogel achieves lowest thermal conductivity with 6   h modification time and 8% PAA due to the optimized structure. Moreover, the peak microwave absorption performance is attained with 18   h modification and 6% PAA, resulting from optimal interfacial polarization loss and impedance matching. This study achieves a balance between thermal insulation and microwave absorption performance through microstructure design, providing a solid foundation for advanced multifunctional materials.

✓ 已验证 产品关联 DOI 高影响因子
查看原文 查看 PubMed
JOURNAL OF ENVIRONMENTAL MANAGEMENT · 2026 · IF 9.2

Maize root exudates modulate laccase-catalyzed polymerization of endocrine-disrupting chemicals to mitigate crop pollution risks

Moyan Qin,Qi Wang,Zhengmin Hu,Taoyi Chen,Hui Lin,Kai Sun

Laccase catalysis represents a promising green strategy for mitigating endocrine-disrupting chemicals (EDCs) and sequestering organic carbon in agroecosystems. However, the mechanistic role of root-exuded metabolites in modulating laccase-catalyzed EDC rhizoremediation within maize ( Zea mays L.) systems remains poorly understood. Here, we probed the influence of maize root exudates (M-REs) on laccase-catalyzed EDC single-electron oxidation and subsequent contaminant uptake at environmentally relevant concentrations. Relative to control treatments without M-REs, supplementation with 10−80 mg L −1  M-REs suppressed laccase-catalyzed bisphenol A transformation, whereas 5−10 mg L −1  M-REs enhanced the transformation of 17 β -estradiol. Covalent co-dimers were identified as reaction products between EDCs and key constituents of M-REs, including phenolic acids (vanillic acid, ferulic acid, protocatechuic acid) and amino acids (glutamic acid, phenylalanine). Notably, prolonged laccase-catalyzed polymerization led to the formation of highly complex, insoluble co-polymers via cross-linking of EDCs with exudate components. These precipitated polymers exhibited low bioavailability and minimal mobility, resulting in significantly reduced EDC phytotoxicity, as evidenced by an improved germination index. Pot trials further demonstrated that laccase-regulated rhizoremediation decreased root uptake rate constants by 51.72% for E2 and 20.59% for BPA compared to enzyme-deficient controls. This efficient sequestration markedly limited the translocation of EDCs to aboveground tissues, thereby minimizing their potential entry into the food chain. Collectively, these findings elucidate the mechanistic role of M-REs in modulating laccase-catalyzed EDC polymerization and subsequent uptake, thereby advancing the development of sustainable and eco-friendly rhizoremediation strategies to support safe agricultural production.

✓ 已验证 产品关联 DOI 高影响因子
查看原文 查看 PubMed
Results in Engineering · 2026 · IF 9.4

Ta2O5 induced aligned growth of mullite achieving superior wear resistance properties

Guangmao Yan,Fei Wang,Yunchuan Yang,Ruiheng He,He Zhou,Jie Huo,Jun Wang,Jing Feng

Coal-series kaolin (CSK), a large-scale solid waste, has caused significant environmental pollution. Its effective conversion into high-value products remains a challenge. In this study, mullite-based ceramics featuring needle-like microstructures were controllably prepared by adding Ta 2 O 5 without the need for additional sintering acids. The resulting ceramics exhibited superior wear resistance. Ta 2 O 5 reacts with Al 2 O 3 to form Ta-O-Al chemical bridges. Combined with density functional theory (DFT) calculations and experimental data, these chemical bridges effectively lower the nucleation energy barrier for new crystalline phases and provide anchoring sites. This drives the transition from equiaxed grains to interwoven whiskers and facilitates the preferential one-dimensional anisotropic growth of the mullite phase. Due to the distinctive needle-like mullite microstructures and the pinning effect of AlTaO 4 , the wear rate decreases by 89% compared to the blank sample. These results demonstrate that Ta 2 O 5 regulates the crystal growth and friction behavior of mullite, offering an economically effective strategy for utilizing CSK.

CAS / MDL: 1314-61-0 1344-28-1
✓ 已验证 产品关联 DOI 高影响因子
查看原文 查看 PubMed
已复制

文献关联基于可获得的产品、CAS、DOI 及引用记录。收录不代表作者或出版方对阿拉丁产品的背书,请以原始文献为准。