文献检索

查找使用阿拉丁产品的科研文献

检索与阿拉丁产品相关的同行评审论文、DOI、PubMed 编号、期刊、作者、CAS 号及研究领域。

科研影响力快照

与阿拉丁产品相关的已发表科研成果

在搜索之前,这些指标可帮助访客快速了解产品关联科研的规模与质量。

347,389+ SCI 论文 与阿拉丁产品引用相关
2,303,681.05 总影响因子 匹配文献记录中影响因子的总和
81.20 最高期刊影响因子 匹配期刊中的最高 IF
6.63 平均期刊影响因子 匹配文献的平均 IF

参考指标 指标基于阿拉丁文献引用数据库及期刊影响因子记录。文献关联仅供科研参考,请以原始文献为准。

产品列表

视图 列表 网格

显示第2869至2880个,产品总数4,488个

切换升序
Cu)
CERAMICS INTERNATIONAL · 2021 ·Vol. 47 ·期 22 ·32025-32032 · IF 4.527

New spinel high-entropy oxides (FeCoNiCrMnXLi)3O4 (X = Cu, Mg, Zn) as the anode material for lithium-ion batteries

ChanQin Duan,Kanghui Tian,Xinglong Li,Dan Wang,Hongyu Sun,Runguo Zheng,Zhiyuan Wang,Yanguo Liu

High-entropy oxides (HEOs) with numerous functional features such as high structure stability and superionic conductivity are considered as promising candidates of electrode materials for lithium-ion batteries (LIBs). In this study, a series of single-phase spinel-structured high-entropy oxides (FeCoNiCrMnXLi) 3 O 4 (X = Cu, Mg, Zn) consisted of seven metal elements at equal molar ratio were synthesized by solid phase method. In-situ high-temperature XRD technique was used to investigate the structure evolution of (FeCoNiCrMnZnLi) 3 O 4 and a single-phase HEO was acquired at 900 °C. As the anode of LIBs, all the HEOs (FeCoNiCrMnXLi) 3 O 4 display excellent cyclic stability and rate capability owe to the expedite three-dimensional Li + transport pathways of spinel structure, the entropy-dominated phase stabilization effect together with the abundant oxygen vacancies introduced by the incorporation of Li + . In comparison, the (FeCoNiCrMnZnLi) 3 O 4 anode containing electrochemical active Zn with tetrahedral coordination structure shows better electrochemical lithium storage performances among the three samples. The ex-situ XRD of (FeCoNiCrMnZnLi) 3 O 4 during the discharge/charge procedure shows an amorphous state structure after the first lithiation process and it retained for the de-lithiation process. This work provides a new strategy to design high-entropy energy-storage material and pave the way for understanding the storage mechanism of HEOs.

✓ 已验证 DOI 高影响因子
查看原文 查看 PubMed
TETRAHEDRON LETTERS · 2018 ·Vol. 59 ·期 51 ·4458-4461 · IF 2.125

Cu-catalyzed decarboxylative iodination of aryl carboxylic acids with NaI: A practical entry to aryl iodides under aerobic conditions

Zhengjiang Fu,Yongqing Jiang,Ligao Jiang,Zhaojie Li,Shengmei Guo,Hu Cai

A simple and practical Cu-catalyzed decarboxylative iodination has been well established under aerobic condition, which provides a useful method to synthesize aryl iodides in moderate to good yields with the use of (hetero)aryl carboxylic acids and NaI as starting materials. Thiabendazole has been prepared via a three-step procedure to show synthetic practicability of the protocol.

✓ 已验证 DOI 高影响因子
查看原文 查看 PubMed
SENSORS AND ACTUATORS B-CHEMICAL · 2023 · IF 8.4

Fuel cell type SO2 sensor based on Cu/CF-N sensing electrode and Nafion proton conductor at room temperature

Lingchu Huang,Sitong Feng,Weijia Li,Huaiyuan Sun,Jianyu Zhang,Qi Lu,Tong Wang,Xiaoyong Sun,Rui Han,Xishuang Liang,Fangmeng Liu,Peng Sun,Fengmin Liu,Bin Wu,Geyu Lu

In this work, nitrogen doped carbon fiber loaded copper (Cu/CF-N) sensing electrode and Nafion proton conductor are used to fabricate fuel cell type gas sensors that realize fast response/recovery for SO 2 detection at room temperature . This is the first time that this type of sensor has been used to detect SO 2 . We investigated the effect of Cu content on sensors’ performance, and found that the Cu (20 wt%)/CF based sensor exhibited the highest response. This can be attributed to the optimal Cu content, which exposes the most active sites. Moreover, nitrogen was doped into electrode material to further improve the performance. Nitrogen atoms enhance the conductivity of the material and its ability to adsorb SO 2 . These are confirmed by the complex impedance measurement and TPD analysis. The upgraded Cu/CF-N fuel cell type gas sensor showed a response of − 435.6 nA to 50 ppm SO 2 and a low detection limit of 500 ppb. Significantly, the Cu/CF-N sensor demonstrated short response time (44 s) and recovery time (87 s) at room temperature. Furthermore, with the advantages of no power consumption , excellent selectivity and good repeatability, the fuel cell type gas sensors have broad prospects in the field of room temperature gas detection.

✓ 已验证 DOI 高影响因子
查看原文 查看 PubMed
MATERIALS CHEMISTRY AND PHYSICS · 2019 · IF 2.781

Controlling ζ-Ta4C3-x laminate growth in TaC0.6 ceramic by addition of Cu and its effect on mechanical properties

Faqiang Shi,Limeng Liu,Zhaoping Hou,Guihong Geng,Yujin Wang

Tantalum carbide ceramics with an overall composition of TaC 0.6 were prepared by hot pressing at 1700 °C for 1 h under 30 MPa pressure with fcc TaC and bcc Ta powder as starting materials. Effects of adding 0–30 mol% Cu on densification, phase formation, microstructural evolution , mechanical properties and electrical conductivity of the obtained composite ceramics were investigated. Full density could be reached at 20 mol% Cu addition and above. Reactions between TaC and Ta resulted in the final phases of hexagonal Ta 2 C and rhombohedral ζ-Ta 4 C 3-x . Plate-shaped ζ laminate grew in both TaC and Ta 2 C and consequently had their sizes confined by the parental grains. Addition of 20–30 mol% Cu could significantly grow the intermediate Ta 2 C grains, hence controlling length of the ζ laminates precipitated in them to form bimodal microstructures consisting of large grains. The 20 mol% Cu composition had a better flexural strength (706 ± 46 MPa) and fracture toughness (9.2 ± 1.7 MPa m 1/2 ). Electrical resistivity at room temperature of the composites decreased with Cu content from 1.03 μΩ m at 0 mol% addition to 0.12 μΩ m at 30 mol% Cu.

研究领域: 材料科学 · 陶瓷学 · 复合材料 · 粉末冶金 · 结构陶瓷 · 物理化学 · 固态化学
✓ 已验证 DOI 高影响因子
查看原文 查看 PubMed
JOURNAL OF POLYMER SCIENCE · 2026 · IF 3.9

Improve the Thermal Conductivity, Insulation Performance and Mechanical Properties of Silicone Rubber by Constructing EG-PDA-Cu Hybrid Nanoparticles

Xingrong Liu,Fan Xia,Dietmar Auhl

In this study, a simple and environmentally benign method was developed to synthesize expanded graphite-polydopamine-copper (EG-PDA-Cu) hybrid nanoparticles. The procedure involved first modifying EG via a mussel-inspired technique to deposit a polydopamine coating, after which Cu 2+ ions were reduced to immobilize copper nanoparticles onto the EG-PDA substrate. The as-synthesized EG-PDA-Cu nanoparticles were subsequently blended into a silicone rubber matrix (VMQ) to form elastomeric composites. Owing to the synergistic contribution of Cu and EG, the 10 wt% EG-PDA-Cu/VMQ composite achieved a thermal conductivity of 1.375 W m −1 K −1 , representing a 7.63-fold enhancement over pristine VMQ (0.18 W m −1 K −1 ). Furthermore, the composites exhibited outstanding electromechanical and mechanical performance. This approach holds significant potential for fabricating high-thermal-conductivity dielectric materials suitable for thermal management in electronic packaging. Graphical In this work, a novel expanded graphite-supported nano-copper polydopamine composite was designed and synthesized. The procedure involved first modifying EG via a mussel-inspired technique to deposit a polydopamine coating, after which Cu 2+ ions were reduced to immobilize copper nanoparticles onto the EG-PDA substrate. This approach holds significant potential for fabricating high-thermal-conductivity dielectric materials suitable for thermal management in electronic packaging.

✓ 已验证 DOI 高影响因子
查看原文 查看 PubMed
LANGMUIR · 2026 ·Vol. 42 ·期 22 ·15967-15977 · IF 4.4

Controllable Fabrication of Nanoporous Gold Microspheres from Low-Gold-Content Cu–Au Alloys for Stable, Deep-Pressing Electronic Packaging

Zhang Li,Zhang Wenhao,Wang Zhaomeng,Fan Sining,Xia Puyue,Tang Shaolong

Porous gold materials, with advantages such as low relative density and high chemical stability, are widely used in biosensing, chemical energy storage, etc. Currently, traditional methods still face challenges in the preparation of ultrafine nanoporous gold microspheres, which limit their application in advanced electronic packaging. In this study, we propose a strategy for the controlled preparation of nanoporous gold microspheres using low-gold-content alloy microspheres, which includes wet chemical reduction, crystal diffusion and growth, liquid–solid interfacial nonwetting effect, and chemical-free corrosion dealloying. Nanoindentation results show that, compared to the brittle crushing under deep pressing of polymer microspheres, the newly prepared nanoporous gold microspheres exhibit significantly low-pressure-stable deep-press anisotropic conductive properties. Specifically, the nanoporous gold microspheres achieve up to 80% compression deformation under a load of approximately 5 mN, primarily due to their unique nanoporous structure, reducing hardness. In terms of piezoresistive performance, the nanoporous gold microspheres maintain stable low-resistance conductive properties during both loading and unloading processes, which is mainly attributed to the large compression deformation enhancing the connection reliability between substrates. When applied to anisotropic conductive film preparation and device encapsulation testing, the results demonstrate that with a powder loading of 5 wt %, the nanoporous gold microsphere-based anisotropic conductive film exhibits a significantly wide pressure encapsulation range (0.1–0.5 MPa), which is directly related to the large compression deformation ability of the nanoporous gold microspheres. This ability can not only reduce the requirement for uniform particle size distribution and save sorting costs but also effectively improve the conductivity of interconnected devices.

✓ 已验证 DOI PubMed 高影响因子
查看原文 查看 PubMed
Journal of Materials Research and Technology-JMR&T · 2026 · IF 7.3

The fabrication mechanism and sintering behaviour of Cu@Ag micro-nano mixed particles solder paste for power electronics packaging

Qinghua Zheng,Wei Zhou,Zhihao Ji,Qian Gao,Xiaolu Wang,Pengrong Lin,Fu Guo

Nano-solder pastes have been proven to be used as a bonding material for power electronics packaging. Especially, the Ag-coated Cu nanoparticles (Cu@Ag NPs) solder paste is gradually becoming a potential candidate. Herein, the innovative structure of Cu@Ag micro-nano mixed particles (Cu@Ag MNPs) is fabricated in the same reaction system. It is found that the nanoparticle and microparticle sizes are dominated by the interaction of multiple parameters. The PVP molecular weight (MW) can mainly control the nanoparticle size by the steric hindrance effect. The reaction time ( t ) can mainly regulate the microparticle size by the particle growth time. The reaction temperature ( T ) can mainly control the microparticle size by the nucleation rate. Besides, based on the observation of in-situ TEM, the sintering behaviour of the Cu@Ag MNPs mainly includes particle connection, void evolution, coarsening, and smoothness in this work. The sintering mechanism includes the atom flow on the surface of the particle, grain boundary diffusion, and Ostwald ripening. Consequently, Cu@Ag MNPs solder paste obtained the lowest porosity and the highest shear strength of Cu-Cu joints compared to the Ag NPs and Cu MPs solder paste at 250 °C and 300 °C without pressure in the air condition. Accordingly, this work clarifies the fabrication mechanism and sintering behaviour of the Cu@Ag particles, which provides a facile strategy and theoretical basis for the development of power electronics packaging.

CAS / MDL: 7758-99-8
✓ 已验证 产品关联 DOI 高影响因子
查看原文 查看 PubMed
JOURNAL OF MATERIALS SCIENCE · 2026 ·Vol. 61 ·期 35 ·26114-26129 · IF 4.4

Preparation of photocatalyst UiO-66-CA-Cu and its photocatalytic activation of peroxymonosulfate for the degradation of tetracycline hydrochloride

Fan Yan,Sun Xueqin,Bi Tao,Hou Bo,Lu Fang

The accumulation of tetracycline antibiotics in water environments can lead to the emergence of antibiotic-resistant bacteria and resistance genes, posing a potential threat to ecosystems and human health. Therefore, the development of cost-effective and efficient methods for the remediation of antibiotic wastewater has become a current research hotspot. In this study, a novel photocatalyst, UiO-66-CA-Cu (CA was the abbreviation for “citric acid”), was prepared by two-step functionalization modification of the MOF material (University of Oslo-66, abbreviated as UiO-66). Under irradiation of simulated sunlight, UiO-66-CA-Cu-led photocatalysis and peroxymonosulfate (PMS) activation co-degradation system achieved 93.3% ( k  = 0.04712 min −1 ) removal efficiency of tetracycline hydrochloride (20 mg/L, 50 mL) within 60 min. The functional modification was used to optimize the local environment of the parent MOF. The asymmetry of the Zr–O cluster structure introduced by CA could effectively improve the separation efficiency of photogenerated carrier in the material, and the introduced Cu 2+ ions could be used as the activation site to further enhance the material’s activation ability to PMS. Graphical In this work, a novel photocatalyst, UiO-66-CA-Cu (CA was the abbreviation for “citric acid”), was prepared by two-step functionalization modification of the MOF material (UiO-66). Under simulated sunlight irradiation, the degradation system constructed by the photocatalyst UiO-66-CA-Cu coupled with peroxymonosulfate (PMS) activation could achieve efficient removal of tetracycline hydrochloride (removal efficiency: 93.3%, k = 0.04712 min -1 ). In addition, we systematically investigated the effects of PMS concentration, photocatalyst concentration and initial pH value on the degradation performance over this system, and further proposed the possible degradation mechanism.

CAS / MDL: 100-21-0 10026-11-6
✓ 已验证 产品关联 DOI 高影响因子
查看原文 查看 PubMed
Microsystems & Nanoengineering · 2026 ·Vol. 12 ·期 1 ·261 · IF 11.1

Laser-induced graphene/Cu-based fully-porous flexible capacitive pressure sensor with ultra-fast response and wide measurement range

Jiang Yimeng,Liang Misheng,Xie Ying,Su Ruige,Wang Bo,Wu Fan,Bian Xiaomeng,Tian He,You Rui

Recently, advances in human-machine interfaces have raised performance demands on flexible sensors. Achieving fast response, wide detection range, and high sensitivity remains a key challenge in flexible pressure sensor design. Here, we present a novel fully-porous flexible capacitive pressure sensor (FPFCPS) with a sandwich structure, comprising laser-induced Cu-composited graphene (LICuG) electrodes and a polyurethane foam dielectric layer modified with ionic liquid and coated with PVA hydrogel. The hierarchical porosity and conductivity of LICuG enable coupled mechanical interlocking and electronic polarization at the electrode-dielectric interface, improving interfacial contact, compressibility, and capacitive response. The sensor achieves a high sensitivity of 863.17 kPa⁻¹, a wide detection range (10 Pa–500 kPa), and a rapid response time of 5 ms, along with excellent flexibility and long-term stability. Notably, FPFCPS enables rapid tactile feedback and material recognition in dynamic robotic operations, offering high-resolution sensing in complex environments. This work represents the first application of LICuG in electric double-layer capacitance-pressure sensors and establishes a new structural design paradigm based on a fully porous architecture. It provides theoretical insights and practical strategies for advancing material development, mechanistic understanding, and implementation of intelligent sensing systems. In this study, femtosecond-laser-induced Cu-composited graphene (LICuG) was successfully synthesized. By incorporating this novel composite material into an electric double-layer capacitance sensing system, a fully-porous flexible capacitive pressure sensor (FPFCPS) was constructed. Through the synergistic regulation of the sensor’s interlayer structural and electrical properties, its overall performance was significantly enhanced. When integrated at key robotic joints, the FPFCPS successfully detected collisions within ~5 ms and was capable of identifying the type of obstacle through tactile contact.

CAS / MDL: 7447-39-4
✓ 已验证 产品关联 DOI PubMed 高影响因子
查看原文 查看 PubMed
JOURNAL OF MATERIALS SCIENCE-MATERIALS IN ELECTRONICS · 2026 ·Vol. 37 ·期 19 ·1481 · IF 3.2

Enhancing electrical and mechanical properties of electrically conductive adhesives via synergistic effect of Ag@Cu particles and silver flakes

Zhang Xiaomin,Qin Mingjun,Tang Weilei,Pang Juan,Lyu Yue,Chen Cheng

Conductive adhesives (ECAs) are critical for advanced electronic packaging, but the high cost of silver fillers limits their widespread application. This study presents a hybrid filler strategy combining silver-coated copper (Ag@Cu) nanoparticles with a low content of silver flakes to achieve high electrical conductivity at reduced cost. The Ag@Cu particles were synthesized via a two-step wet chemical reduction method, yielding a well-defined core–shell structure with a dense silver coating that prevents copper oxidation. A series of ECAs were prepared with silver flakes and Ag@Cu nanoparticles at a fixed total filler loading of 70%. The results demonstrate that the optimal silver flake content is 4%, at which the ECA exhibits the lowest volume resistivity of 3 × 10⁻ 4 Ω·cm. The prominent conductivity improvement stems from synergistic geometric regulation. Low loading silver flakes serve as conductive bridges to fill interparticle gaps and construct hybrid point-to-face contact, verified by SEM. The silver flake composite retains favorable shear strength and thixotropy for screen printing. A circuit test with printed films lit an LED, validating its feasibility for flexible circuits. This work develops low cost, high-performance ECAs using Ag@Cu nanoparticles and silver flakes, achieving a balance between excellent conductivity and reduced material cost.

CAS / MDL: 1336-21-6
✓ 已验证 产品关联 DOI 高影响因子
查看原文 查看 PubMed
ANALYTICA CHIMICA ACTA · 2026 · IF 6.1

Multichannel colorimetric sensor array enabled by microwave-rapidly synthesized Cu/Fe single-atom nanozymes for broad-spectrum pesticide screening

Lili Liu,Yi Yuan,Haibo He,Junping Dong,Xitian Peng,Xiaoxia Yan,Liqiang Luo

Cu/Fe-N-C SAzymes with dual enzyme activities are rapidly synthesized via microwave. • A four-channel sensor array enables pesticide-specific fingerprint-like responses. • The array discriminates three types of pesticides (5–500 ng/mL) and their mixtures. • LDA and LOOCV confirm robust broad-spectrum screening capability toward pesticides. • High-throughput screening of multi-pesticide residues in fruits is validated. Background The widespread and excessive use of pesticides poses significant risks to both human health and ecological integrity. Inspired by the mammalian olfactory cross-response mechanisms, colorimetric sensor arrays provide a rapid, cost-effective and visual platform for multi-residue pesticide monitoring. Results Herein, we report a four-channel response array constructed from Cu-N-C and Fe-N-C single-atom nanozymes rapidly synthesized via microwave assistance. These nanozymes exhibit intrinsic laccase-like (LAC) and peroxidase-like (POD) dual enzymatic activities, which are differentially modulated by distinct pesticide classes to generate characteristic fingerprint-like responses. Integrating with linear discriminant analysis (LDA) for dimensionality reduction and visualization, this array successfully discriminates three major pesticide categories―sulfonylureas, organophosphates, and carbamates, comprising nine typical pesticides within the discrimination concentration range of 5–500 ng/mL, and further distinguishes pesticide mixtures of varying compositional ratios. Significance Leave-one-out cross-validation (LOOCV) confirms the robust broad-spectrum classification capability of the system. The practical utility of this array is demonstrated through high-throughput screening of multi-pesticide residues in fruit samples. The synergistic integration of microwave-accelerated nanozyme synthesis and multichannel colorimetric sensing establishes a versatile and reliable paradigm for universal pesticide detection in complex matrices. Two single-atom nanozymes, Cu-N-C and Fe-N-C, exhibiting both laccase-and peroxidase-like activities, are rapidly prepared by microwave-assisted synthesis. A four-channel colorimetric array is then established, in which the nanozyme activities are differentially modulated by distinct pesticide categories (sulfonylureas, organophosphates, and carbamates), producing characteristic fingerprint responses. Linear discriminant analysis (LDA) enables precise discrimination of nine pesticides and their mixtures over a concentration range of 5–500 ng/mL, with robust classification confirmed by leave-one-out cross-validation (LOOCV). This platform represents a reliable and efficient strategy for high-throughput screening of multi-pesticide residues in fruits. Download: Download high-res image (303KB) Download: Download full-size image

✓ 已验证 DOI 高影响因子
查看原文 查看 PubMed
JOURNAL OF RADIOANALYTICAL AND NUCLEAR CHEMISTRY · 2026 · IF 1.7

Efficient photoelectrocatalytic separation of uranium from complex wastewater using a flour-derived Cu single-atom/carbon nitride composite electrode

Guo Yuanyuan,Wang Ying,Shan Haiwei,Zhang Lieyu,Wang Hongqiang

The treatment of uranium-containing wastewater faces major challenges, including complex compositions, strong interference from coexisting ions, poor selectivity of conventional methods, and rapid blockage of electrode active sites. Here, we utilize expired flour as a low-cost biomass carbon/nitrogen source and copper oxalate as a copper precursor to prepare a biomass-derived carbon-supported copper single-atom catalyst (Cu-SAs/BC). This catalyst is then composited with g-C 3 N 4 at an optimal mass ratio of 2:3 and loaded onto carbon felt to construct a Cu-SAs/BC-g-C 3 N 4 photoelectrocatalytic electrode. The electrode achieves a uranium removal efficiency of 99.4% within 5 min under optimal conditions (total loading 13 mg, pH 4–6), and exhibits rapid removal across a wide initial concentration range of 5–100 mg/L. The distribution coefficient for U(VI) reaches 6.5 × 10 4  mL/g, significantly surpassing those of coexisting interfering ions (Al, Zn, Fe, Mn, Ca). Complete uranium removal from actual uranium mining seepage water is achieved within 20 min. Mechanistic studies confirm that phosphate groups on the electrode surface specifically chelate and coordinate with UO 2 2+ enabling rapid and targeted enrichment of uranyl ions. The UO 2 2+ ions then migrate to Cu-N x active sites, accept electrons, and undergo reduction to form U(Ⅳ), producing UO 2 precipitates that automatically detach under square-wave potential for efficient separation. This study provides a low-cost, sustainable biomass-derived single-atom catalytic material and a technological pathway for uranium recovery from complex radioactive wastewater.

✓ 已验证 DOI 高影响因子
查看原文 查看 PubMed
已复制

文献关联基于可获得的产品、CAS、DOI 及引用记录。收录不代表作者或出版方对阿拉丁产品的背书,请以原始文献为准。