文献检索

查找使用阿拉丁产品的科研文献

检索与阿拉丁产品相关的同行评审论文、DOI、PubMed 编号、期刊、作者、CAS 号及研究领域。

科研影响力快照

与阿拉丁产品相关的已发表科研成果

在搜索之前,这些指标可帮助访客快速了解产品关联科研的规模与质量。

347,389+ SCI 论文 与阿拉丁产品引用相关
2,303,681.05 总影响因子 匹配文献记录中影响因子的总和
81.20 最高期刊影响因子 匹配期刊中的最高 IF
6.63 平均期刊影响因子 匹配文献的平均 IF

参考指标 指标基于阿拉丁文献引用数据库及期刊影响因子记录。文献关联仅供科研参考,请以原始文献为准。

产品列表

视图 列表 网格

显示第2965至2976个,产品总数4,488个

切换升序
Cu)
Journal of Environmental Chemical Engineering · 2022 · IF 7.968

Construction of Cu2O/Cu heterojunction with hierarchical hollow sphere structure as visible-light driven photocatalyst for efficient water remediation

Junhua Li,Linsen Huang,Zhimei Yang,Zengjian Liu,Xiaosong Sun

Sunlight driven photocatalytic degradation is an effective and eco-friendly technology for water remediation . And formation of metal-semiconductor heterojunction provides a promising strategy to enhance the photocatalytic efficiency of photocatalyst. In this work, the hierarchical Cu 2 O/Cu hollow sphere was newly prepared by a simple template-free and one-pot solvothermal method without using any organic capping agents. The composition, morphology structure and photoelectric properties of the prepared photocatalysts were investigated by the characterization of XRD, XPS, SEM, TEM , nitrogen adsorption/desorption isotherms, UV-DRS and EIS, etc. It was found that the Cu 2 O/Cu composite with hierarchical hollow sphere structure exhibits good stability and excellent photocatalytic activity for the degradation of methyl orange (MO) and tetracycline (TC) under visible light, because the huge specific surface area provides more active sites and the Cu 2 O/Cu heterojunction could efficiently facilitate photogenerated carries separation. Further, free radical scavenging experiments and EPR tests confirmed the ·O 2 - radicals were produced and played the most important role in the photocatalytic process. Finally, the possible photocatalytic mechanism and the transfer processes of photogenerated carriers of hierarchical Cu 2 O/Cu hollow sphere was proposed. As a result, the hierarchical Cu 2 O/Cu hollow sphere may be a suitable candidate of high-efficiency photocatalyst for the wastewater treatment .

CAS / MDL: 3317-61-1
✓ 已验证 产品关联 DOI 高影响因子
查看原文 查看 PubMed
APPLIED SURFACE SCIENCE · 2022 · IF 7.392

Porous cellulose gel-regulated flower-like ZnO-Cu nanoparticles for enhancing interfacial catalysis activity and recyclability in environmental catalysis

Lili Zhang,Chun Shi,Hailong Lu,Hongwei Li,Xiaofan Zhou,Zhiguo Wang,Jinxia Ma

The recyclability of heterogeneous catalysts directly affects their utilization efficiency, use cost, sustainability, and environmental issues. Herein, the flower-like ZnO-Cu nanoparticles with high interfacial reactivity were in-situ synthesized in the porous cellulose gel to obtain the ZnO-Cu/cellulose composite gel (ZnO-Cu/CCG) catalyst, which possesses superior recycling and reusing stability thanks to the bulk nature of the gel. The ZnO-Cu/CCG catalysts with tunable sheet-like and flower-like ZnO were fabricated by the dissolution of cellulose into zinc chloride (ZnCl 2 ) solvent and regeneration using different coagulating baths (water, ethanol, or isopropanol). The CCG prepared from isopropanol coagulation exhibited the highest specific surface area (291.6 m 2 /g) and porosity (92.3%). The various network structures of CCG provided different nucleation sites and growing spaces for controllable preparation of ZnO with tunable morphology. The complete removal of methyl orange (MO), Congo red (CR), and methylene blue (MB) required only 80 sec, 3 min, and 5 min, using flower-like ZnO-Cu/CCG catalysts prepared by isopropanol coagulating bath, the pseudo-first-order rate constant (k) is 2.8170 min −1 , 1.1330 min −1 , and 0.8506 min −1 , respectively, much higher than that of the ZnO-Cu powders. Furthermore, the catalytic reusability of ZnO-Cu/CCG can be investigated over 50 successive cycles, in which the catalytic efficiency did not decrease appreciably.

CAS / MDL: 16940-66-2
✓ 已验证 产品关联 DOI 高影响因子
查看原文 查看 PubMed
CHEMICAL ENGINEERING JOURNAL · 2022 · IF 16.744

Desulfurization mechanism of an excellent Cu/ZnO sorbent for ultra-deep removal of thiophene in simulated coke oven gas

Fanjing Wei,Xiaoxia Zhang,Junjie Liao,Jiawei Guo,Weiren Bao,Liping Chang

The reactive adsorption desulfurization mechanism of thiophene over Cu/ZnO sorbent in coke oven gas (COG) was established by a combination of theoretical and experimental study. The adsorption behavior of thiophene on Cu surface was studied by density functional theory (DFT) method. The C 4 hydrocarbons releases and sulfur migration over Cu/ZnO sorbent during the thiophene removal process were investigated by comparing with that over CuO, ZnO and CuO+ZnO (prepared by mechanical grinding of CuO and ZnO) sorbents. The results show that the parallel adsorption of thiophene on hexagonal closest packing (HCP) site of Cu (1   1   1) crystal face is the optimal adsorption mode. Cu 0 nanoparticles in Cu/ZnO sorbent have two important roles: (1) adsorb and dissociate H 2 , and (2) cleave the C–S bond of thiophene. The sulfur after the cleavage of C–S bond could transfer directly to ZnO and eventually be converted into ZnS without the intermediate product CuS. During thiophene removal, C 4 H 6 and C 4 H 10 are generated over Cu/ZnO sorbent in the presence of H 2 . ZnO in Cu/ZnO sorbent not only acts as an excellent sulfur accepter, but can greatly affect the adsorption properties by enhancing the spillover and storage of hydrogen atoms . Increasing the interaction between Cu 0 nanoparticles and ZnO to enhance hydrogen spillover is an effective way to improve the thiophene reactive adsorption activity of Cu/ZnO.

✓ 已验证 产品关联 DOI 高影响因子
查看原文 查看 PubMed
SCIENCE OF THE TOTAL ENVIRONMENT · 2022 · IF 10.753

Assessing the impact of different salinities on the desorption of Cd, Cu and Zn in soils with combined pollution

Lijun Wu,Weifeng Yue,Nengzhan Zheng,Mengshen Guo,Yanguo Teng

Exploring the relationships between heavy metal release and salinity can help address the problems of combination of toxic heavy metals and salinization in contaminated soils. Therefore, in this study, the release characteristics of heavy metals (Cd, Cu and Zn) under different salt types and mass concentrations were investigated through batch desorption experiments. Spearman's correlation analysis was performed to assess the effects of typical physicochemical properties on metal release under salt stress. The results indicated that the types and concentration gradients of salt had notably different impacts on the release of different metals; specifically, there were significant impacts for Cd but slight impacts for Cu and Zn. MgCl 2 and CaCl 2 had more obvious promoting effects on Cd release, followed by a salt mixture and NaCl, and this pattern was similar for Zn release. Most salts could slightly restrain the release of Cu, except for MgCl 2 and Na 2 SO 4 , which had slight promoting effects. Moreover, low levels of CaCl 2 could effectively restrain the release of Cu. The results showed that the release capacities of metals followed the order of Cd > Cu > Zn, possibly attributed to the competitive adsorption among cations. Ferromanganese oxides in the soil favored the release of Cd and Zn under salt treatments, and redox potential was an important factor affecting Cu release. The results also suggested that the background values of metals could affect metal release, but the effects were varied under different salt treatments for Zn. The reason for this may be that the addition of different salts changed the effects of certain soil properties on the metal release. Overall, this study can serve as an important reference for controlling heavy metal pollution in soils in salinization and coastal areas.

✓ 已验证 产品关联 DOI PubMed 高影响因子
查看原文 查看 PubMed
ENVIRONMENTAL RESEARCH · 2022 · IF 8.431

Cu–Ce oxide Co-loaded silicon nanocapsules for hydrogen peroxide self-supplied Fenton-like catalysis and synergistically antibacterial therapy

Yuxin Zhu,Yue Zhao,Xun Sun,Fuhao An,Lanya Jiao,Xuan Sun

Antibacterial strategies based on reactive oxygen species (ROS) have opened up a new avenue for overcoming the great challenges of antibiotics topic including lack of broad-spectrum antibiotics and the emergence of super-resistant bacteria. Herein, we leveraged a strategy of constructing synergistic catalytic active sites to develop a simple yet efficient Fenton-like active nanocomposite, and investigated its catalysis mechanism and antibacterial performance thoroughly. This strategy provides a new direction for boosting the catalytic activity of nanocomposite catalysts for wide application. Specifically, by uniformly loading copper oxide and ceria onto the surface of silica nanocapsules (SiO 2 NCs), we fabricated a bimetallic oxide nanocomposite Cu 0.75 Ce 0.62 O 2 @SiO 2 NC, which performed superior Fenton-like capability in a wide pH range without additional exogenetic hydrogen peroxide (H 2 O 2 ). Such excellent catalytic activity was originated from the charge interaction between the two metal oxide components, where formation of Cu + and oxygen vacancies (OVs) was mutually reinforcing, resulting in a synergistic effect to produce H 2 O 2 and catalyze the generation of •OH under the slight acid condition (pH = 6.0). In view of the outstanding Fenton-like activity, the Cu 0.75 Ce 0.62 O 2 @SiO 2 NC was employed in antimicrobial testing, which demonstrated exceptional high in vitro antimicrobial efficacy against both the S. aureus and E. coli in a neutral environment (pH = 7.4). The excellent performance of the bimetallic nanocomposite Cu 0.75 Ce 0.62 O 2 @SiO 2 NC, including its facile and mild preparation, high water-solubility and stability, superior catalytic and antimicrobial performances, manifests a promising broad-spectrum antibiotic that can be anticipated to deal with the contamination of the environment by bacteria.

CAS / MDL: 16774-21-3 681-84-5
✓ 已验证 产品关联 DOI PubMed 高影响因子
查看原文 查看 PubMed
APPLIED CATALYSIS B-ENVIRONMENTAL · 2022 · IF 24.319

Electrochemical hydrogenation of biomass-based furfural in aqueous media by Cu catalyst supported on N-doped hierarchically porous carbon

Wanling Xu,Chunjie Yu,Jinzhu Chen,Zhiyong Liu

Electrochemical hydrogenation (ECH) is a particularly important and environmentally friendly approach to obtain biomass-based fuels and high value-added fine chemicals without using external hydrogen. Herein, we reported a highly efficient and selective ECH of furfural (FF) into furfuryl alcohol (FA) with Cu-based electrocatalyst in aqueous alkaline media. Under the optimal conditions, FA selectivity close to 100% with 99% FF conversion and total Faradaic efficiency above 95% were obtained with the electrocatalyst. Mechanism investigation suggests an ECH mechanism for FA formation, which is highly potential-dependent to FA selectivity, requiring low and well-matched concentrations between active hydrogen (H ads ) species and FA radical on the Cu surface. Moreover, the electrocatalyst shows an excellent stability and recyclability during the eight-time consecutive recycling experiments, yielding a total amount of 1011 mg FA. This work thus highlights an important guidance for electrocatalytic upgrading of biomass-based platform molecules in an environmentally friendly way.

✓ 已验证 产品关联 DOI 高影响因子
查看原文 查看 PubMed
JOURNAL OF THE EUROPEAN CERAMIC SOCIETY · 2022 · IF 6.364

Cu-modified Pb(Mg1/3Nb2/3)O3-PbZrO3-PbTiO3 textured ceramics with enhanced electromechanical properties and improved thermal stability

Linjing Liu,Bin Yang,Shuai Yang,Qiangwei Kou,Hang Xie,Yuan Sun,Yunfei Chang,Shan-Tao Zhang,Fei Li

Grain-oriented Pb(Mg 1/3 Nb 2/3 )O 3 -PbZrO 3 -PbTiO 3 (PMN-PZ-PT) based ceramics were synthesized through templated grain growth via using BaTiO 3 (BT) templates. Although BT templates are partially destroyed by PMN-PZ-PT matrix, CuO addition remarkably promotes [001] c -oriented grain growth behavior of the ceramics, resulting in an improvement of Lotgering factor F 001 from ~86% to 98%. Both crystallographic texture and CuO doping increase tetragonality and reduce average domain size of the ceramics dominated by rhombohedral phase. Consequently, 0.50 wt% CuO-doped ceramics ( F 001 ~98%) exhibit optimum electromechanical properties: d 33 ~860 pC/N, d 33 × g 33 ~48.6 × 10 −12 m 2 /N, k p ~0.80, E c ~7.2 kV/cm, tan δ ~0.8% and T c ~222 °C. In addition to ~3.7 times and 6.6 times higher d 33 and d 33 × g 33 , those ceramics possess about 240% enhanced piezoelectric strain and much better thermal stability ( S max / E max variation ≤2% between RT and 150 °C) relative to non-textured counterpart. This work offers a good paradigm for simultaneously exploring high piezoelectric response and good temperature stability in piezoceramics, benefiting the development of next-generation advanced electromechanical devices.

✓ 已验证 产品关联 DOI 高影响因子
查看原文 查看 PubMed
ACS Omega · 2023 · IF 4.1

Novel Cu@Ag Micro/Nanoparticle Hybrid Paste and Its Rapid Sintering Technique via Electromagnetic Induction for High-Power Electronics

Zhuohuan Wu,Wei Liu,Jiayun Feng,Zhicheng Wen,Xinyue Zhang,Xinming Wang,Chunqing Wang,Yanhong Tian

Due to the harsh working environments up to 600 °C, the exploration of high-temperature interconnection materials is significantly important for high-power devices. In this study, a hybrid paste including Cu@Ag core–shell microparticles (MPs) and Ag nanoparticles (NPs) was designed to achieve Cu–Cu bonding. The Cu@Ag MPs exhibited excellent oxidation stability in an air atmosphere with the Ag layer coating on the Cu core. Ag NPs fill the pores among the Cu@Ag MPs and reduce the sintering temperature of the hybrid paste. The Cu–hybrid paste–Cu joints were formed via electromagnetic induction heating within approximately 15 s. When sintered at 26 kW, the shear strength of the joint reached 48 MPa, the porosity decreased to 0.73%, and the resistivity was down to 13.25 μΩ·cm. Furthermore, a possible interconnection mechanism at the contact interface between the Cu substrate and the sintered hybrid paste was proposed, which is related to the melting point of metal particles and the effect of magnetic eddy currents. This fast bonding technology inspires a new approach to interconnection for high-power devices under high operation temperatures.

CAS / MDL: 107-21-1 25322-68-3
✓ 已验证 产品关联 DOI PubMed 高影响因子
查看原文 查看 PubMed
Journal of Water Process Engineering · 2023 · IF 7

Mixed matrix membrane reactor containing core-shell 4A-Fe@Cu Fenton catalyst for high-performance removal of congo red

Lilan Huang,Haimei Chen,Jin Han,Haojie Chen,Jian Pan,Zihan Zhao,Zhichao Dong,Hailin Cong

Printing and dying wastewater has a pervasive problem afflicting people worldwide due to negative impacts on ecosystems and humans. Herein, Fe/Cu bimetallic catalyst/polyethersulfone (4A-Fe@Cu/PES) mixed matrix membrane (APMMM) with macropore and high porosity were developed as catalytic membrane reactor for reduction of congo red (CR) in flow-through reaction. The forced flow of the reactants through the membrane improved the mass transfer and intensified the contact between reactants and immobilized catalysts, allowing for efficient adsorption and catalysis. Furthermore, the CR adsorption by 4A-Fe@Cu would form catalytic microzones in the membrane, which was conducive to further improving the catalytic efficiency. As a result, the apparent activation energy of dynamic catalysis (21.1 kJ/mol) was significantly decreased compared with that of static catalysis (93.7 kJ/mol). Therefore, the dynamic processes exhibited more excellent adsorption and catalytic efficiency. In cross-flow circulation mode, the maximum CR adsorption capacity of APMMM-18 (doping amount of 4A-Fe@Cu is 18.0 wt%) was 199.5 mg/g 4A-Fe@Cu with a catalyst/CR mass ratio of 1/1.5 and initial CR concentration of 50 mg/L. For catalysis, the APMMM-18 could remove 99.8 % CR after 5 h with a catalyst/CR mass ratio of 1/1.5 and 1.9 mM of H 2 O 2 at pH 8. The catalytic membranes showed much higher performances than 4A-Fe@Cu particles even under lower H 2 O 2 conditions. The intrinsic CR adsorption and degradation ratio of one layer of APMMM-18 under dead-end filtration was also investigated. The combination of the Fenton catalyst with the membrane process accomplished the effective removal of CR.

CAS / MDL: 7440-47-3
✓ 已验证 产品关联 DOI 高影响因子
查看原文 查看 PubMed
JOURNAL OF MATERIALS SCIENCE-MATERIALS IN ELECTRONICS · 2023 ·Vol. 34 ·期 21 ·1-14 · IF 2.8

Fabrication of high reliability Cu joints at low temperatures using synergistic effect of organic composition for power device packaging

Sun Quan,Liu Yang,Zhang Jing,Li Ke,Lu Jicun

Copper paste sintering has great potential for WBG (wide bandgap) semiconductor packaging, but the problems of copper susceptibility to oxidation and high sintering temperatures have hindered its development. A micron copper paste suitable for low-temperature sintering was successfully formulated using the synergistic effect of metal organic decomposition (MOD) ink and ascorbic acid (AA) to achieve high shear strength sintered joints. During the sintering process, AA acted as a reducing agent to effectively remove oxide on the surface of the Cu microparticles (MPs), while the decomposition process of MOD was facilitated by the reduction products. The diffusion channels formed by the decomposed nanoparticles connect the Cu-MPs, forming dense sintered joints. At a sintering temperature of 250 °C, the combination of MOD and AA in the paste resulted in a significant improvement in the shear strength of the sintering joints, reaching 102.2 MPa. This is in contrast to the addition of only MOD or AA, which resulted in a shear strength of less than 5 MPa. Furthermore, the strength of the sintered joints was increased to 128.1 MPa after storage at 250 °C for 1000 h. At a sintering temperature of 210 °C, the strength could still reach 47.6 MPa, which was approximately double the strength of traditional Sn-based solder joints. This has greater practical significance for the fabrication of high-strength bonded joints and the expansion of the sintering process window.

CAS / MDL: 50-81-7
✓ 已验证 产品关联 DOI 高影响因子
查看原文 查看 PubMed
JOURNAL OF MOLECULAR LIQUIDS · 2023 · IF 6

Experimental characterization and dynamical modeling evaluation for enhanced BTA removal by three amino acids in post-Cu-CMP cleaning

Shihao Zhang,Yazhen Wang,Baimei Tan,Fangyuan Wang,Xiaolong Wang,Haoyu Du

Post-chemical mechanical polishing (CMP) cleaning is an indispensable process to remove organic residues and particles on the wafer surface after CMP. Benzotriazole (BTA), a dominant corrosion inhibitor in Cu-CMP slurry, can easily remain on the copper surface after CMP, affecting the performance and yield of devices, and its removal has attracted more attention. This paper revealed the effect and mechanism of three amino acids, lysine, serine, and proline, on BTA removal in tetraethyl ammonium hydroxide-based alkaline solutions during post-Cu-CMP cleaning. Experimental results showed a diminishing enhancement in the cleaning efficiency of BTA after adding lysine (97.1%), serine (96.7%), and proline (94.1%) with almost the same concentration. Ultraviolet–visible absorption spectrum proved the lysine’s complexing ability was slightly better than the other. Besides, quantum chemical parameters of amino acid molecules calculated by density functional theory further suggested that lysine has more reactive sites and mainly bonds with copper through N2 and N8. The adsorption structures of three amino acids were simulated through the molecular dynamics method, and lysine turned out to be parallel absorbed on the Cu (1   1   1) surface with the lowest adsorption energy of −30.24 eV. Finally, the cleaning process simulation revealed the dynamic behaviors of BTA and lysine.

CAS / MDL: 56-87-1 147-85-3 56-45-1
✓ 已验证 产品关联 DOI 高影响因子
查看原文 查看 PubMed
JOURNAL OF ALLOYS AND COMPOUNDS · 2023 · IF 6.2

One-pot biosynthesis of two-dimensional dendrite-like Cu/C hybrids with excellent anti-oxidation property for flexible electronics

Huangqing Ye,Jiahui Chen,Songrui Wei,Yougen Hu,Yu Wang,Xian-Zhu Fu,Rong Sun

Copper/carbon (Cu/C) hybrids with two-dimensional (2D) dendritic-like structure were successfully synthesized by a one-pot biological hydrothermal method with biomass as the reducing agent, capping agent, and template. By hydrothermal carbonization, the graphitic carbon is in-situ coated on the surface of nano copper to obtain a new type of 2D Cu/C materials. This method was facile, green, tunable and scalable. The influential factors on the morphology and carbon content of as-prepared hybrids were investigated, and possible growth mechanism was proposed. The as-prepared Cu/C hybrid materials exhibited a smallest thickness of 2.5 nm, with a radius-to-thickness ratio as high as 10 3 . Benefiting from the typical 2D structure and graphitic carbon coating layer, Cu/C hybrids exhibited excellent oxidation resistance and electrical conductivity , thus having great potential as a conductive adhesive filler used in the field of flexible electronics.

CAS / MDL: 7758-99-8
✓ 已验证 产品关联 DOI 高影响因子
查看原文 查看 PubMed
已复制

文献关联基于可获得的产品、CAS、DOI 及引用记录。收录不代表作者或出版方对阿拉丁产品的背书,请以原始文献为准。