JOURNAL OF MATERIALS SCIENCE-MATERIALS IN ELECTRONICS
·
2019
·Vol. 30
·期 24
·21089-21095
·
IF 2.195
Sun Fan,Chen Guixiong,Zhou Xiongtu,Wu Chaoxing,Sun Lei,Yan Qun,Guo Tailiang,Zhang Yongai
Thin-film encapsulation (TFE) is essential and challenging for flexible organic/quantum dot light-emitting diodes (OLEDs/QLEDs). In this work, SiO 2 nanoparticles were added into the NEA 121 polymer (s-NEA) to prolong the permeation pathways, showing good barrier property and high optical transparency. With increasing the concentration of SiO 2 nanoparticles up to 20 mg/ml, the value of water vapor transmission rate (WVTR) decreased. A single s-NEA layer with silica concentration of 20 mg/ml and thickness of ~ 75 µm exhibited WVTR of 2.5 × 10 −3 g/m 2 /day and light transmittance of above 80%. Al 2 O 3 thin films fabricated using atomic layer deposition were inserted between s-NEA layers to form dyad-style Al 2 O 3 /s-NEA multilayers. The Al 2 O 3 (60 nm)/s-NEA (20 µm) multilayers with 3 units exhibited WVTR of 2.6 × 10 −5 g/m 2 /day and consistently demonstrated a significantly extended QLED lifetime.
✓ 已验证
产品关联
DOI
高影响因子
JOURNAL OF THERMAL ANALYSIS AND CALORIMETRY
·
2019
·Vol. 142
·期 1
·425-435
·
IF 2.471
Qian Yi,Qiao Peng,Li Long,Han Haoyue,Zhao Rongmin,Zhang Haiming
In this article, a pillared layered antimony hydroxide (Sb-LH) material has been prepared by the hydrothermal method. X-ray diffraction, Fourier-transform infrared spectroscopy and transmission electron microscope results showed that Sb-LH was synthesized successfully. Then Sb-LH was added into thermoplastic polyurethane (TPU) to investigate the effect on flame retardancy and smoke suppression by cone calorimeter test, limiting oxygen index, smoke density test and thermalgravimetric analysis (TGA). Compared with pure TPU, the peak heat release rate and total heat release of TPU composites filled with 2 mass% Sb-LH were reduced by 56.1% and 28.3%, respectively. Among all TPU composites, TPU3 (1.5 mass% Sb-LH loading) had the best smoke suppression. Meanwhile, Sb-LH can remarkably improve the char yield of TPU composites with Lewis acid catalysis obtained by TGA results.
✓ 已验证
产品关联
DOI
高影响因子
JOURNAL OF NANOBIOTECHNOLOGY
·
2019
·Vol. 17
·期 1
·1-18
·
IF 5.345
Niu Shiwei,Williams Gareth R.,Wu Jianrong,Wu Junzi,Zhang Xuejing,Chen Xia,Li Shude,Jiao Jianlin,Zhu Li-Min
Background It is extremely difficult to develop targeted treatments for triple-negative breast (TNB) cancer, because these cells do not express any of the key biomarkers usually exploited for this goal.Results In this work, we develop a solution in the form of a cascade responsive nanoplatform based on thermo-sensitive poly(N-vinylcaprolactam) (PNVCL)-chitosan (CS) nanoparticles (NPs). These are further modified with the cell penetrating peptide (CPP) and loaded with the chemotherapeutic drug doxorubicin (DOX). The base copolymer was optimized to undergo a phase change at the elevated temperatures of the tumor microenvironment. The acid-responsive properties of CS provide a second trigger for drug release, and the inclusion of CPP should ensure the formulations accumulate in cancerous tissue. The resultant CPP-CS-co-PNVCL NPs could self-assemble in aqueous media into spherical NPs of size < 200 nm and with low polydispersity. They are able to accommodate a high DOX loading (14.8% w/w). The NPs are found to be selectively taken up by cancerous cells both in vitro and in vivo, and result in less off-target cytotoxicity than treatment with DOX alone. In vivo experiments employing a TNB xenograft mouse model demonstrated a significant reduction in tumor volume and prolonging of life span, with no obvious systemic toxicity.Conclusion sThe system developed in this work has the potential to provide new therapies for hard-to-treat cancers.
✓ 已验证
产品关联
DOI
PubMed
高影响因子
CELLULOSE
·
2019
·Vol. 26
·期 17
·9163-9178
·
IF 3.917
Li Bo,Pan Yuanfeng,Zhang Qi,Huang Zhihong,Liu Jie,Xiao Huining
Modified porous cellulose beads (MCBs) with typical sizes ranging from 2 to 3 mm were successfully fabricated via acidic precipitation from the cellulose dissolved in ionic liquid, followed by surface-grafting with aminoguanidine hydrochloride using glutaric anhydride as a coupling agent. The nano-sized calcium carbonate (30% wt on dry cellulose) was added to cellulose solution prior to the precipitation in acidic medium in an attempt to promote the formation of the pore structure of cellulose beads. Modified cellulose powders (MCPs) (size 150 μm) were prepared by precipitating the solution of the cellulose which reacted with glutaric anhydride homogeneously in ionic liquid, followed by grafting with aminoguanidine hydrochloride. The pseudo-second-order kinetic model and the Langmuir isotherm model described the adsorption process well. The maximum adsorption capacities of MCBs towards Hg(II) and Cu(II) were 581.4 and 94.88 mg/g; whereas the maximum adsorption capacities of MCPs for Hg(II) and Cu(II) were 625 and 98.52 mg/g, respectively. The results demonstrated that both MCBs and MCPs are highly effective and promising as green-based adsorbents for the removal of heavy metal ions in aqueous systems, Hg 2+ in particular.
✓ 已验证
产品关联
DOI
高影响因子
JOURNAL OF MATERIALS SCIENCE
·
2019
·Vol. 55
·期 2
·577-590
·
IF 3.442
Chen Ailian,Ma Xiangyu,Cai Wenjie,Chen Yang
This work described a straightforward synthetic route to fabricating polymer/silica hybrid particles with controllable architectures and their advantages as abrasives. The poly(vinylpyrrolidone)-modified and divinyl benzene cross-linked polystyrene (PS) cores were synthesized via a developed soap-free emulsion polymerization, and the outer dendritic-like mesoporous silica (D-mSiO 2 ) shells were coated onto the cores using an oil–water biphase approach combined with a selective removal of hexadecyltrimethylammonium bromide templates. The resulting core/shell PS/D-mSiO 2 samples were characterized by SEM, TEM, XRD, FTIR, and nitrogen adsorption/desorption, offering comprehensive information on the composition, structure, morphology, pore size, shell thickness, and surface area. The pore size of D-mSiO 2 can be controlled within the range of 3–9 nm by varying the upper oil phases, which serve as swelling agents to enlarge the mesochannels. The PS/D-mSiO 2 particles can be used as novel polishing abrasives and present superior surface quality (0.16 ± 0.02 and 0.26 ± 0.03 nm of root-mean-square roughness) compared to the commercial solid SiO 2 ones (0.54 ± 0.05 nm). Moreover, the PS/D-mSiO 2 hybrids with an enlarged pore size result in an inferior structural stability, which is important for final surface finish and removal rate. The presented results provide not only a strategy for preparing PS/D-mSiO 2 core/shell particles with tunable pore sizes, but also a regulation that can be applied to prepare other core/shell hybrids with dendritic-like mesosilica shells.
✓ 已验证
产品关联
DOI
高影响因子
Nanoscale Research Letters
·
2019
·Vol. 14
·期 1
·1-7
·
IF 3.159
Tan Xi,Kang Wenbin,Liu Jingfeng,Zhang Chuhong
Molybdenum disulfide (MoS 2 ) is an extremely intriguing low-D layered material due to its exotic electronic, optical, and mechanical properties, which could be well exploited for numerous applications to energy storage, sensing, and catalysis, etc., provided a sufficiently low number of layers is achieved. A facile exfoliation strategy that leads to the production of few-layered MoS 2 is proposed wherein the exfoliation efficacy could be synergistically boosted to > 90% by exploiting ultrasound sonication in supercritical CO 2 in conjunction with N -methyl-2-pyrrolidone (NMP) as the intercalating solvent, which is superior to general practiced liquid exfoliation methods wherein only the supernatant is collected to avoid the majority of unexfoliated sediments. The facile and fast exfoliation technique suggests an exciting and feasible solution for scalable production of few-layered MoS 2 and establishes a platform that contributes to fulfilling the full potential of this versatile two-dimensional material.
✓ 已验证
产品关联
DOI
PubMed
高影响因子
JOURNAL OF ELECTRONIC MATERIALS
·
2019
·Vol. 49
·期 3
·1819-1826
·
IF 1.676
Gu Kang,Hao Ruiting,Guo Jie,Aierken Abuduwayiti,Liu Xinxing,Chang Faran,Li Yong,Wei Guoshuai,Liu Bin,Wang Lu,Sun Shuaihui,Ma Xiaole
In this work, the (Ag,Cu) 2 ZnSnS 4 (ACZTS) thin films were fabricated via sputtering with a multi-target to form different layer stacks, i.e., (S1) ZnS/Sn/Cu/Ag/Mo,(S2) ZnS/Sn/Ag/Cu/Mo and (S3) ZnS/Ag/Sn/Cu/Mo. The stacked precursors were sulfurized through a soft annealing, followed by a two-step sulfurization in a chamber filled with N 2 at standard atmospheric pressure. The x-ray photoelectron spectroscopy elemental profile showed a vertical non-uniform distribution of Ag in the film. Based on the results of scanning electron microscopy and electron probe microanalysis, Ag enrichment of the upper surface was beneficial for the grain size. Moreover, a dense, uniform surface could be obtained and the stability of the elemental composition could be maintained. After optimizing the order of the Ag layers, the efficiency of the solar cells increased from 1.30% to 3.65%, an improvement of 181%. The open circuit voltage is increased from 448 mV to 630 mV because of the reduced voids, increased grain size, and reduced Cu Zn antisite defects.
✓ 已验证
产品关联
DOI
高影响因子
Journal of Neuroinflammation
·
2019
·Vol. 16
·期 1
·1-13
·
IF 5.7
Wu Xuan,Fu Siming,Liu Yun,Luo Hansheng,Li Feng,Wang Yiying,Gao Meng,Cheng Yuan,Xie Zongyi
Background Neuroinflammation and blood-brain barrier (BBB) disruption are two vital mechanisms of secondary brain injury following intracerebral hemorrhage (ICH). Recently, melanocortin-1 receptor (Mc1r) activation by Nle4-D-Phe7-α-MSH (NDP-MSH) was shown to play a neuroprotective role in an experimental autoimmune encephalomyelitis (EAE) mouse model. This study aimed to investigate whether NDP-MSH could alleviate neuroinflammation and BBB disruption after experimental ICH, as well as the potential mechanisms of its neuroprotective roles.Methods Two hundred and eighteen male C57BL/6 mice were subjected to autologous blood-injection ICH model. NDP-MSH, an agonist of Mc1r, was administered intraperitoneally injected at 1 h after ICH insult. To further explore the related protective mechanisms, Mc1r small interfering RNA (Mc1r siRNA) and nuclear receptor subfamily 4 group A member 1 (Nr4a1) siRNA were administered via intracerebroventricular (i.c.v) injection before ICH induction. Neurological test, BBB permeability, brain water content, immunofluorescence staining, and Western blot analysis were implemented.Results The Expression of Mc1r was significantly increased after ICH. Mc1r was mainly expressed in microglia, astrocytes, and endothelial cells following ICH. Treatment with NDP-MSH remarkably improved neurological function and reduced BBB disruption, brain water content, and the number of microglia in the peri-hematoma tissue after ICH. Meanwhile, the administration of NDP-MSH significantly reduced the expression of p-NF-κB p65, IL-1β, TNF-α, and MMP-9 and increased the expression of p-CREB, Nr4a1, ZO-1, occludin, and Lama5. Inversely, the knockdown of Mc1r or Nr4a1 abolished the neuroprotective effects of NDP-MSH.Conclusion sTaken together, NDP-MSH binding Mc1r attenuated neuroinflammation and BBB disruption and improved neurological deficits, at least in part through CREB/Nr4a1/NF-κB pathway after ICH.
✓ 已验证
产品关联
DOI
PubMed
高影响因子
COLLOID AND POLYMER SCIENCE
·
2020
·Vol. 298
·期 3
·233-241
·
IF 1.536
Xue Min,Chen Ming,Chang Wenhao,Chen Ruiyang,Li Pengna
We have presented a simple method for situ fabrication of photoluminescent lanthanide metallogels. A series of lanthanide metallogels could be rapidly formed through mixing the aqueous solution of Tb 3+ or Eu 3+ and organic solution of synthesized aromatic carboxylic ligands ( DCn , n = 14, 16,18) at room temperature. The gelation tests revealed that the ligand with longer alkyl chain ( DC18 ) showed stronger gelling abilities, indicating that the structure of non-coordinated groups in ligand molecules could affect self-assembly processes and, hence, the microstructures and properties of lanthanide metallogels. FT-IR measurements demonstrated that the driving force of formation of the metallogels was the coordination interaction between DCn and Tb 3+ or Eu 3+ . XRD analysis revealed that DC14 metallogels took a mixture of hexagonal and tetragonal packing modes. All obtained metallogels have shown typical luminescent emissions of the lanthanide complex. In particular, DC18 /Tb(NO 3 ) 3 metallogel in DMF/H 2 O ( v : v = 1:1) has shown excellent self-supporting, self-healing, film-forming, and rheological properties.
The Tb 3+ /Eu 3+ metallogels have been formed with aromatic carboxylic acids as ligands, and they have shown excellent luminescent, self-healing, film-forming, and rheological properties.
✓ 已验证
产品关联
DOI
高影响因子
Nature Communications
·
2019
·Vol. 10
·期 1
·1-10
·
IF 11.878
Xie Qingqiao,Chen Xixi,Wu Tianli,Wang Tiankuo,Cao Yi,Granick Steve,Li Yuchao,Jiang Lingxiang
The radial geometry with rays radiated from a common core occurs ubiquitously in nature for its symmetry and functions. Herein, we report a class of synthetic asters with well-defined core-ray geometry that can function as elastic and radial skeletons to harbor nano- and microparticles. We fabricate the asters in a single, facile, and high-yield step that can be readily scaled up; specifically, amphiphilic gemini molecules self-assemble in water into asters with an amorphous core and divergently growing, twisted crystalline ribbons. The asters can spontaneously position microparticles in the cores, along the radial ribbons, or by the outer rims depending on particle sizes and surface chemistry. Their mechanical properties are determined on single- and multiple-aster levels. We further maneuver the synthetic asters as building blocks to form higher-order structures in virtue of aster-aster adhesion induced by ribbon intertwining. We envision the astral structures to act as rudimentary spatial organizers in nanoscience for coordinated multicomponent systems, possibly leading to emergent, synergistic functions.
✓ 已验证
产品关联
DOI
PubMed
高影响因子
JOURNAL OF MATERIALS SCIENCE-MATERIALS IN ELECTRONICS
·
2019
·Vol. 30
·期 21
·19137-19146
·
IF 2.195
Xiang Ye,Zou Hao,Xu Yifeng,Deng Yuehong,Zhu Jie,Wu Wan,Zhou Yi
In this article, the novel direct Z-scheme ZnIn 2 S 4 @BiOBr-(110) heterojunction structure was firstly synthesized via simple two-step hydrothermal method. The results of XRD and HRTEM indicated that as-prepared BiOBr mainly exposed high energy (110) facet. Simultaneously, the photoelectrochemical measurement was performed to further investigate the photo-induced carrier separation efficiency. The results indicated that Z-scheme heterojunction structure formed by the loading of ZnIn 2 S 4 nanosheets not only promoted the separation of photogenerated carriers and inhibited fast recombination rate of photogenerated electron–hole pairs of pure BiOBr, but also endowed the composite with better redox activity. The degradation efficiency of RhB by BiOBr loaded with 10 mol% ZnIn 2 S 4 has achieved 98% within 18 min under the irradiation of Xe lamp, which demonstrated that the unique direct Z-scheme ZnIn 2 S 4 @BiOBr-(110) composite photocatalytic materials has the potential application in environmental pollution control and energy conversion.
✓ 已验证
产品关联
DOI
高影响因子
MICROCHIMICA ACTA
·
2019
·Vol. 186
·期 11
·1-9
·
IF 5.479
Ma Guangran,Xu Hui,Wu Meijuan,Wang Lin,Wu Jianghua,Xu Fugang
A ternary hybrid composed of molybdenum disulfide (MoS 2 ), reduced graphene oxide (rGO) and gold nanoparticles (AuNPs@MoS 2 -rGO) was prepared and used for voltammetric detection of hydroquinone (HQ), catechol (CC) or resorcinol (RC). The composition and structure of the hybrid were characterized in detail. The electrochemical behaviors of a glassy carbon electrode (GCE) modified with the hybrid towards the oxidation of HQ, CC, and RC were investigated using cyclic voltammetry (CV) and differential pulse voltammetry (DPV). The results revealed 3D MoS 2 is active for the catalytic oxidation of these isomers. Additional integration with rGO and AuNPs further improves catalysis due to their synergistic interaction. The enhanced catalysis leads to oxidation of HQ, CC and RC at 0.074 V, 0.178 V, and 0.527 V (vs. Ag/AgCl; by CV) with reduced overpotential (20-100 mV) and 8-fold or 3-fold increased peak current compared to those obtained on MoS 2 /GCE, or MoS 2 -rGO/GCE, respectively. Selective detection of one isomer in the presence of the other two was realized by DPV. The linear ranges are 0.1–950 μM, 3–560 μM, and 40–960 μM for HQ, CC, and RC, and the detection limits are 0.04 μM, 0.95 μM, and 14.6 μM, respectively. The sensor also shows good selectivity and displays satisfactory recovery for real sample analysis.
Schematic illustration of the preparation of AuNPs@MoS 2 -rGO hybrid by hydrothermal growth of MoS 2 -rGO and subsequent electrodeposition of gold nanoparticles (AuNPs), and its application for selective detection of hydroquinone, catechol and resorcinol by voltammetry.
✓ 已验证
产品关联
DOI
PubMed
高影响因子