FOOD CHEMISTRY
·
2023
·
IF 8.8
Huilin Li,Jingying Yang,Ran Han,Yueyao Wang,Xintong Han,Shuo Wang,Mingfei Pan
Rapid, sensitive, specific and stable detection of mycotoxin in food remains an extremely crucial issue. Herein, a magnetic-fluorescent immunosensing platform for the detection of zearalenone (ZEN) was proposed. The platform utilized Au nanoparticles (AuNPs) heterogeneous fluorescent metal–organic framework (MIL-53(Al)@AuNPs) labeled with ZEN-bovine serum albumin (ZEN-BSA) as signal probe and ZEN mono-antibodies coupled with magnetic NPs (MNPs-mAbs) as capture probe. Specifically, the heterogenization of AuNPs on the MIL-53(Al) surface improved its biocompatibility, and facilitated the loading of ZEN-BSA conjugates. The MNPs-mAbs could rapidly capture the target ZEN, simplify the immunoassay process and further improve the detection efficiency. The established competitive magnetic-fluorescent immunosensing platform had a wider linear response to ZEN in the range of 0.001–100 ng/mL with a lower limit of detection (LOD) at 0.0035 ng/mL, and could finish the whole detection process within 20 min, showing great potential for rapid and sensitive detection of food contaminants.
✓ 已验证
产品关联
DOI
PubMed
高影响因子
POLYHEDRON
·
2019
·
IF 2.284
Ning Tian,Yifang Dai,Qing Liu,Wei Dai
A general synthetic strategy for HS-Fe 3 O 4 @MIL-53(Al) adsorbent has been developed in this work. The composite material exhibits an efficient capture performance for rubidium ion due to sulfhydryl group and magnetic Fe 3 O 4 doped in its porous cavity. The results of X-ray diffraction, scanning electron microscopy, Fourier transform infrared spectroscopy, and N 2 adsorption–desorption proved that the HS-Fe 3 O 4 was immobilized in the composite material. High Rb + uptake capacity over the HS-Fe 3 O 4 @MIL-53(Al) is attributed to the exchange of acidic protons between the sulfhydryl group and the Rb + . The pseudo-second-order and Freundlich model could make a good description of the adsorption process. The Rb + sorption selectivity was moderately influenced by any co-ions effect (K + , Na + and Cs + ) due to HS-Fe 3 O 4 doped. These results reveal that our novel composite material might be a promising industrial adsorbent for Rb + capture.
✓ 已验证
产品关联
DOI
高影响因子
INDUSTRIAL & ENGINEERING CHEMISTRY RESEARCH
·
2016
·
IF 2.567
Huimin Ruan,Changmeng Guo,Hongwei Yu,Jiangnan Shen,Congjie Gao,Arcadio Sotto,Bart Van der Bruggen
This study reports the fabrication of mixed matrix membranes (MMMs) using immersion precipitation phase inversion for promising application in desalination of dye solutions. Aromatic poly(m-phenylene isophthalamide) is used as the polymer material, and the metal–organic framework MIL-53(Al) is added to develop integrally skinned asymmetric membranes. Successful dispersion of MIL-53(Al) particles into the membrane-separating layer is confirmed by scanning electron microscopy. The optimum performance of the membranes is obtained at 0.5 wt % MIL-53(Al) concentration. In particular, the M-0.5 membrane is planned for use in separating dye/salt aqueous mixtures. It is observed that the M-0.5 membrane has a rejection for NaCl and Na2SO4 below 11% and 37%, respectively, in mixed salt/dye solutions. Additionally, the M-0.5 membrane is found to have a rejection rate of 83.9%, 98.3%, and 99.8% for nitroso-R salt, xylenol orange, and ponceau S, respectively, in mixed Na2SO4/dye solutions. The rejection rate for Na2SO4 is lower than that of some commercial nanofiltration membranes (NF90, NF270, and DK). The membrane is promising for dye desalination in industrial-scale applications.
✓ 已验证
产品关联
DOI
高影响因子
ACS Applied Nano Materials
·
2024
·
IF 5.3
Wenjing Li,Weichen Wang,Mingyue Zhu,Peiao Cong,Daowei Gao,Rongyao Wang,Guozhu Chen
Metal oxides@metal–organic framework (MOFs)-based core/shell nanostructures demonstrate promising potential in catalytic hydrogenations. However, the direct nucleation and growth of MOFs on the topologically diverse surfaces of metal oxides face significant challenges due to the high interfacial energy resulting from topological mismatches. Herein, we present a facile in situ growth strategy for directly assembling an MIL-53(Al) layer on the surface of CeO2 nanospheres at low temperatures by mixing and stirring CeO2 nanospheres and MIL-53(Al) precursors without requiring sacrificial templates or additional surface modifications. Moreover, key factors such as reaction time, temperature, and the types of aluminum salts and ligands are systematically explored to comprehensively understand the nucleation behavior of MOFs shells. Notably, when active Pt nanoparticles are sandwiched between the CeO2 core and the MIL-53(Al) shell, the MIL-53(Al) effectively stabilizes the Pt nanoparticles and enhances the selectivity of hydrocinnamaldehyde in cinnamaldehyde hydrogenation. CeO2/Pt@MIL-53(Al) achieved more than twice the selectivity for HCAL compared to CeO2/Pt and even outperformed Pt/MIL-53(Al). Undoubtedly, this study provides distinctive insights into the nucleation and growth mechanisms of MOFs on metal oxides, expands the strategies for fabricating metal oxides@MOFs core/shell nanostructure, and proposes innovative ideas and possibilities for broadening the application domains of MOFs-based materials.
✓ 已验证
产品关联
DOI
高影响因子
SEPARATION AND PURIFICATION TECHNOLOGY
·
2025
·
IF 9
Xin-Ru Chen,Heng Mao,Qiu-Ying Zhang,Wei-Min Liu,Shen-Hui Li,Qian-Qian Li,Li-Hao Xu,Yan-Mei Zhang,Xin-Yue Zhang,Jun-Jie Liu,Ao Kou,Zhi-Ping Zhao
Interfacial engineering in mixed matrix membranes (MMMs) is essential to attain superior separation performance and ensure long-term operational stability. In this research, a range of novel MMMs were designed and fabricated for pervaporation (PV) separation of n-butanol/water solution by introducing the MIL-53(Al) particles and three variants (i.e., MIL-53(Al)–NH 2 , MIL-53(Al)–NO 2 , MIL-53(Al)–OH) into PEBA polymer matrix. These four MIL-53(Al) counterparts were synthesized via a microwave-assisted solvothermal method by selectively functionalizing the terephthalic acid linkers with different chemical groups. The functional MIL-53(Al) variants were employed to explore the relationship between membrane microstructures and PV performance by manipulating the interfacial interactions with PEBA matrix. The findings reveal that incorporating MIL-53(Al) variants not only displayed excellent interfacial compatibility and uniform dispersion within PEBA matrix, but also constructed the preferential transport pathways for n-butanol over water molecules. Impressively, in a 1 wt% n-butanol aqueous solution at 40 °C, the resultant membrane attained a permeation flux of 1483.3 g·m -2 ·h -1 and a separation factor of 18.1. Compared to the PEBA/PVDF membrane, the total flux was enhanced by 17.1 %, and the separation factor was improved by 46.4 %. Moreover, the embedding MIL-53(Al) variants boosted thermal and mechanical properties of the membrane, endowing it with considerable potential for practical applications.
✓ 已验证
产品关联
DOI
高影响因子
Journal of Environmental Chemical Engineering
·
2026
·Vol. 14
·期 5
·123915
·
IF 7.5
Jumeng Di,Xiaohua Li,Songyu Guan,Wenwen Ma,Wen Li,Jie Gao,Yuzhi Xu,Bing Yu,Hailin Cong
Nanoplastics (NPs) pose severe risks to aquatic environments, and adsorption technology provides a promising strategy for their removal. Metal-organic frameworks (MOFs) are promising adsorbents, but their practical application is limited by insufficient water stability and restricted pore accessibility. To bridge this gap, defect-engineered Al/Mn bimetallic MOFs were synthesized via mild post-synthetic ion exchange. n-Octanoic acid (OA) was employed to modulate the crystallization process of MIL-53(Al), inducing missing linker defects, suppressing excessive crystal growth, and generating mesoporous structure. Subsequently, the partial substitution of terephthalic acid linkers with manganese clusters could introduce additional active sites, alter the surface properties while maintain the overall crystallinity of MOFs. The optimized Mn-0.2-OA maintained high PS removal efficiency under acidic to neutral conditions, with removal efficiencies above 92% over pH 1–7. It also showed good tolerance to representative interference factors, retaining removal efficiencies above 97.5% in the presence of common cations and 89.37% at 40 mg/L humic acid. The adsorption of 500 nm polystyrene microspheres was mainly driven by the synergistic effects of electrostatic attraction, π-π interactions, enhanced hydrophobic affinity, and hierarchical pore structure. Meanwhile, Mn-0.2-OA achieved a Langmuir-fitted maximum adsorption capacity of 849.17 mg/g and exhibited rapid adsorption kinetics, removing 96.4% of PS within 10 min at an initial concentration of 25 mg/L. Regeneration tests further confirmed its acceptable reusability for repeated PS adsorption. This strategy provides a feasible approach for designing efficient and reusable adsorbents for nanoplastic removal from aquatic environments.
✓ 已验证
产品关联
DOI
高影响因子
JOURNAL OF SOLID STATE CHEMISTRY
·
2022
·
IF 3.656
Chunfu Liu,Chenyu Zhu,Han Wang,Shenao Xie,Junyang Zhou,Hongjun Fang
Co-doped metal organic frameworks (MOFs) were fabricated by a facile route and applied to remove (tetracycline, congo red, methylene blue and rhodamine B) through integrated adsorption and photocatalysis . The assembled MOFs composite exhibited larger S BET (889 m 2 /g), broad light adsorption, and accelerated carrier kinetics, which helped to enhance adsorption and photocatalysis performance. Specifically, nearly 100% TC (40 mg/L) could be removed by the Co-MIL-10 within 12 min solar-light irradiation, significantly faster than that of solo MIL-53(Al) (82%) and CoAl-LDH (54%), separately. Furthermore the obtained rate constant (0.2064 min −1 ) was 4.8 times and 9.7 times greater than that of MIL-53(Al) and CoAl-LDH, respectively. The quenching/EPR characterization suggested that photo-generated h + / • O 2 − / • OH species were responsible for TC oxidation , of which h + showed the great impact. Cycling experiments verified the robust stability of the MOFs catalyst. As well, an underlying photocatalytic mechanism of the current system was investigated in detail.
✓ 已验证
产品关联
DOI
高影响因子
ENVIRONMENTAL RESEARCH
·
2022
·
IF 8.431
Luan Minh Nguyen,Ngoan Thi Thao Nguyen,Thuy Thi Thanh Nguyen,Dai Hai Nguyen,Duyen Thi Cam Nguyen,Thuan Van Tran
The global occurrence of textile dyes pollution has recently emerged, posing a serious threat to ecological systems. To abate dye contamination, we here developed a novel magnetic porous CoFe 2 O 4 @MIL–53(Al) nanocomposite by incorporating magnetic CoFe 2 O 4 nanoparticles with MIL–53(Al) metal–organic framework. This nanocomposite possessed a surface area of 197.144 m 2 g −1 and a pore volume of 0.413 cm 3 g −1 . The effect of contact time (5–120 min), concentration (5–50 mg L −1 ), dosage (0.1–1.0 g L −1 ), and pH (2–10) on Congo red adsorption was clarified. CoFe 2 O 4 @MIL–53(Al) could remove 95.85% of Cong red dye from water with an accelerated kinetic rate of 0.6544 min −1 within 10 min. The kinetic and isotherm models showed the predominance of Bangham and Temkin. According to Langmuir, the maximum uptake capacities of CoFe 2 O 4 @MIL–53(Al), CoFe 2 O 4 , and MIL–53(Al) adsorbents were 43.768, 17.982, and 15.295 mg g −1 , respectively. CoFe 2 O 4 @MIL–53(Al) was selected to optimize Cong red treatment using Box–Behnken experimental design. The outcomes showed that CoFe 2 O 4 @MIL–53(Al) achieved the highest experimental uptake capacity of 35.919 mg g −1 at concentration (29.966 mg L −1 ), time (14.926 min), and dosage (0.486 g L −1 ). CoFe 2 O 4 @MIL–53(Al) could treat dye mixture (methylene blue, methyl orange, Congo red, malachite green, and crystal violet) with an outstanding removal efficiency of 81.24% for 30 min, and could be reused up to five cycles. Therefore, novel recyclable and stable CoFe 2 O 4 @MIL–53(Al) is recommended to integrate well with real dye treatments systems.
✓ 已验证
产品关联
DOI
PubMed
高影响因子
SEPARATION AND PURIFICATION TECHNOLOGY
·
2023
·
IF 8.6
Chenxi Shi,Kunpeng Wang,Chongchong Chen,Yijun Cao,Guoli Zhou,Jingtao Wang,Cong Li
Gallium, with an average content of about 15 μg g −1 in the Earth's crust, ranks at the forefront of strategic metals. However, the separation of gallium remains challenging due to the similar physical and chemical properties of gallium and other impurity ions. Herein, the tetradentate amidoxime-functionalized MIL-53(Al) nanofiber membranes (PAN/MIL-53-AO) are prepared to separate gallium, aluminum, vanadium ions and so on. The resultant membranes display 231.08 mg g −1 for Ga(Ⅲ) with high selectivity in static and dynamic adsorption. Specially, PAN/MIL-53-AO demonstrates excellent gallium regeneration rate of 84.25% after five cycles. According to DFT calculations, due to the tetradentate structure of MIL-53(Al)-AO, the amidoxime group binds to gallium ion with a lower binding energy (−29.46 eV). In conclusion, the experimental dates and theoretical calculations indicate that the excellent adsorption capacity is derived from the high binding ability of unique rhombic tetragonal coordination structure for gallium ion and the specific MIL-53(Al) cavity size for passage of gallium. Such performances outperform most state-of-the-art adsorption membranes. The special structure of MOF pores provides a novel approach for rapid synthesis of adsorption sites with high selectivity, with potential utilization in the selective adsorption of gallium ions.
✓ 已验证
产品关联
DOI
高影响因子
APPLIED CATALYSIS B-ENVIRONMENTAL
·
2021
·
IF 19.503
Huanan Zhao,Zipeng Xing,Siyi Su,Sijia Song,Zhenzi Li,Wei Zhou
NH 2 -MIL-53(Al)/CdS p-n heterojunctions are fabricated via facile two-step hydrothermal method. The formation of p-n heterojunctions could form built-in field, which favors spatial charge separation. The resultant NH 2 -MIL-53(Al)/CdS p-n heterojunctions with narrowed band gap extend the photoresponse, and have a high specific surface area of 417.7 m 2 g −1 , and a narrow pore size of 8.8 nm. Under visible light irradiation, the photocatalytic efficiency for reduction of Cr(VI) and removal of refractory pesticide trichlorophenol is up to 99.23 and 98.85 %, respectively. The photocatalytic oxygen evolution is also as high as 563.6 μmol g −1 h −1 . The excellent photocatalytic activity can be ascribed to the efficient p-n heterojunctions accelerating charge transfer and favoring spatial charge separation, and the special mesoporous structure supplying adequate surface-active sites and facilitating mass transfer. This facile strategy opens up new insights for fabricating other p-n heterojunctions photocatalysts with efficient solar energy conversion.
✓ 已验证
产品关联
DOI
高影响因子
TALANTA
·
2025
·
IF 6.1
Qiaoli Yang,Xiao Yang,Ke Guo,Guangrui Pan,Qiuzheng Du,Liang Ming,Wanhai Wang
Pseudomonas aeruginosa (PA) infection poses a significant threat to human health and the economy, with the issue of drug resistance becoming increasingly severe. How to quickly, accurately, and inexpensively detect PA and differentiate live bacteria from dead ones is crucial for clinical follow-up treatment. To this end, we have developed a biosensor based on fluorescent metal-organic frameworks (MOFs) (Eu 3+ @MIL-53(Al)) and specific-phages for PA detection, where the Eu 3+ @MIL-53(Al) prepared by one-pot method exhibits excellent fluorescence properties. By covalently binding specific phages isolated from hospital wastewater to the EuMOF surface, we constructed a fluorescent biosensor capable of detecting PA within 15 min, with a sensitivity threshold of 2 CFU/mL. Notably, this biosensor demonstrates high specificity, accurately quantifying live PA in complex bacterial mixtures and distinguishing live from dead bacteria. Its practical application has been validated in clinical blood and stool samples. As a novel platform for clinical microbial monitoring, the Eu 3+ @MIL-53(Al)-phage biosensor not only holds substantial economic potential but also carries significant public health implications.
✓ 已验证
产品关联
DOI
PubMed
高影响因子
NEW JOURNAL OF CHEMISTRY
·
2024
·
IF 2.7
Yongzhao Zhang,Xuzheng Chen,Yunlei Zhou,Tao Feng,Luping Lyu,Zhenya Zhu,Yifan Liu
The efficient transformation of glucose into 5-hydroxymethylfurfural (5-HMF) is crucial for sustainable bio-refinery processes, but achieving high production efficiency remains challenging. In this study, we presented the preparation of Al-containing metal-organic frameworks (MOFs), specifically MIL-53(Al), MIL-53(Al)-NO2, and MIL-53(Al)-NH2, using different ligands as catalysts to enhance the production of 5-HMF from glucose. Comprehensive characterization provided valuable insights into the properties of the synthesized MOFs. The synthesized MOFs exhibited varied MIL-53(Al) states, morphologies, and thermal stabilities based on the different ligands employed, which in turn affected their catalytic performance. Among the Al-containing MOFs synthesized, MIL-53(Al)-NH2 demonstrated remarkable catalytic capabilities for the conversion of glucose to 5-HMF. This MOF achieved an impressive 5-HMF yield of 53% and a reaction selectivity of 54%. The catalytic efficiency was further enhanced by leveraging the synergistic effect of MIL-53(Al)-NH2 in combination with Amberlyst-36, resulting in a 5-HMF yield of 59% and a reaction selectivity of 60%.
✓ 已验证
产品关联
DOI
高影响因子
危险品化学品经营许可证（带存储）