JOURNAL OF MATERIALS SCIENCE-MATERIALS IN ELECTRONICS
·
2018
·Vol. 29
·期 13
·11178-11186
·
IF 2.324
Cheng Yali,He Yue,Li Shuo,Wang Yifang,Zhao Yan,Li Yu,Li Haiying,Liu Li
In the present work, the acetone gas sensing material based on pure α-Fe 2 O 3 nanotubes, pure and Cu-doped α-Fe 2 O 3 porous nanotubes were fabricated by electrospinning and annealing processes. Different Cu dopant concentrations are introduced to investigate the dopant’s role in sensing performance. The structures and chemical compositions of the as-prepared products were examined using a series of material characterization methods including XRD, EDS, SEM and nitrogen adsorption–desorption analysis. And the acetone sensing results demonstrate that the gas sensitivity of porous nanotubes is better than nanotubes. Moreover, compared with pure samples, the sensor based on 3.0 wt% Cu-doped α-Fe 2 O 3 porous nanotubes exhibits higher response (99.43/100 ppm) and excellent selectivity towards acetone at 164 °C. Meanwhile, the detection limit can extend down to ppb level (2.2/100 ppb). Additionally, the sensor also shows fast response and recovery time (5/18 s) and good repeatability to acetone. The enhancement of gas sensitivity is ascribed to not only the effective utility of hollow and porous structures, but also the high catalytic activity of the Cu additive.
✓ 已验证
产品关联
DOI
高影响因子
POLYMER
·
2018
·
IF 3.483
Zhen Yang,Liqin Cao,Jing Li,Jiangli Lin,Jide Wang
Macroporous poly( N -methylol acrylamide)–high internal phase emulsion [poly(NMA)HIPE] composite monoliths were prepared by carbon dioxide-in-water (CO 2 /W) emulsions using metal-organic framework (MOF) Cu-BDC (BDC = 1,4-dicarboxybenzene) as stabilizer . The composite monoliths were characterized using XRD , SEM, EDS-mapping, FT-IR, TG, and mercury injection methods. Increasing the internal phase fraction would lead to the decrease of monolith density and the increase of void size, and it is favorable for the formation of macroporous interconnected structure with low density and porosities up to 81.6%. The mechanical properties of the Cu-BDC/poly(NMA)HIPE and Cu-BDC removal were also evaluated. The composite polyHIPEs exhibited high antibacterial activity against Escherichia coli . The presented approach facilitated the clean manufacture of open-celled MOF based scaffolds in a one-pot process with porosity of up to 82%.
✓ 已验证
产品关联
DOI
高影响因子
ACS Applied Materials & Interfaces
·
2019
·
IF 8.456
Zhongxi Xie,Shuang Liang,Xuechao Cai,Binbin Ding,Shanshan Huang,Zhiyao Hou,Ping’an Ma,Ziyong Cheng,Jun Lin
Hypoxia and overexpression of glutathione (GSH) are typical characteristics of the tumor microenvironment, which severely hinders cancer treatments. Here, we design a novel biodegradable therapeutic system, O2–Cu/ZIF-8@Ce6/ZIF-8@F127 (OCZCF), to simultaneously achieve GSH depletion and O2-enhanced combination therapy. Notably, the doped Cu2+ doubles the O2 storage capacity of the ZIF-8 matrix, which makes OCZCF an excellent pH-sensitive O2 reservoir for conquering tumor hypoxia, enhancing the photodynamic therapy (PDT) efficiency of chlorin e6 (Ce6) under 650 nm laser irradiation. Moreover, the released Cu2+ can act as a smart reactive oxygen species protector by consuming intracellular GSH. The byproduct Cu+ will undergo highly efficient Fenton-like reaction to achieve chemodynamic therapy (CDT) in the presence of abundant H2O2. The accompanying O2 will further alleviate hypoxia. The in vitro and in vivo experimental data indicate that OCZCF could cause remarkable tumor inhibition through enhanced synergetic PDT and CDT, which may open up a new path for cancer therapy.
✓ 已验证
产品关联
DOI
PubMed
高影响因子
Journal of Environmental Sciences
·
2019
·
IF 3.556
Qing Wu,Li He,Zhong Wei Jiang,Yang Li,Ting Ting Zhao,Yu Han Li,Cheng Zhi Huang,Yuan Fang Li
Efficient removal of non-biodegradable and hazardous dyes from wastewater remains a hot research topic. Herein, a rationally designed a Cu(II)-based metal–organic gel (Cu-MOG) with a nanoporous 3D network structure prepared via a simple one-step mixing method was successfully employed for the removal of cationic dyes. The Cu-MOG exhibited high efficiency, with an adsorption capacity of up to 650.32 mg/g, and rapid adsorption efficiency, with the ability to adsorb 80% of Neutral Red within 1 min. The high adsorption efficiency was attributed to its large specific surface area, which enabled it to massively bind cationic dyes through electrostatic interaction, and a nanoporous structure that promoted intra-pore diffusion. Remarkably, the Cu-MOG displayed size-selective adsorption, based on adsorption studies concerning dyes of different sizes as calculated by density functional theory . Additionally, the adsorption performance of the Cu-MOG still maintained removal efficiency of 100% after three regeneration cycles. These results suggested that the Cu-MOG could be expected to be a promising and competitive candidate to conveniently process wastewater.
✓ 已验证
产品关联
DOI
PubMed
高影响因子
JOURNAL OF HAZARDOUS MATERIALS
·
2018
·
IF 6.434
Ying Liu,Yong Feng,Yunfei Zhang,Shun Mao,Deli Wu,Huaqiang Chu
In this study, the presence of Cu(II) ions was found for the first time to severely inhibit +-dimethyl phthalate (DMP) degradation by ozone due to the formation of the stable complex Cu(II)-DMP. However, 100% DMP removal was rapidly reached when ethylenediamine tetraacetic acid (EDTA) was added with a Cu(II)/EDTA molar ratio of 3:1. Subsequent studies indicated that Cu(II)-DMP is sequestrated by EDTA, then DMP was degraded and Cu(II) was removed by precipitation. The freshly formed Cu-EDTA 2− and organic nitrogen intermediates further decomposed O 3 into OH, which induced to the rapid degradation of DMP. The k obs of Cu-EDTA/O 3 were 9–10 times greater than the k obs of DMP removed by ozonation alone within 10 min. The reaction mechanism involved a OH generation was proposed. The OH and O 2 - are generated from the rapid reaction between ozone and EDTA. Acting as a more strongly negative species, the specific Cu(II) in Cu-EDTA complexes is more inclined to react with O 2 - to give Cu(I), accelerating the forward reaction to produce more OH. The synergistic removal of DMP and Cu(II) can be achieved after reaction. Therefore, this study provides an effective method to dispose metal ion and organic pollutant wastewater.
✓ 已验证
产品关联
DOI
PubMed
高影响因子
JOURNAL OF LUMINESCENCE
·
2018
·
IF 2.732
Ze Min Hu,Guang Tao Fei,Li De Zhang
The Cu-Ga-S/ZnS quantum dots (QDs) emitting green-to-red light are successfully synthesized by the conventional hot-injection method. In the preparation process, 1-dodecanethiol (DDT) is not only used as the solvent but also the sulfur precursor and ligand. Therefore, all reactants are additives, which can reduce solution contamination. The peak wavelength of Cu-Ga-S/ZnS QDs' emission can be tuned from 520 to 619 nm by changing Cu/Ga stoichiometry . And these quantum dots have narrow full-width at half maximum wavelength of about 75 nm. Furthermore, a white quantum-dot-based light-emitting diode is obtained by depositing the yellow Cu-Ga-S QDs on a blue InGaN chip.
✓ 已验证
产品关联
DOI
高影响因子
Journal of Materials Chemistry A
·
2018
·Vol. 6
·期 38
·18649-18659
·
IF 9.931
Zheming Liu,Aiwei Tang,Jun Liu,Dongxu Zhu,Xifeng Shi,Qinghua Kong,Zhijie Wang,Shengchun Qu,Feng Teng,Zhanguo Wang
Multinary copper-based chalcogenides have been exploited in photocatalytic hydrogen generation due to their exceptional visible light absorption properties and environmentally friendly character. Similar to other photocatalysts, to reinforce the charge separation and transfer is one of the most important pathways to enhance photocatalytic hydrogen evolution, which can be achieved by rationally designing the nanostructures and geometries of multinary copper-based chalcogenides. Herein, an improved photocatalytic hydrogen evolution is successfully realized in L-shaped Cu–Ga–Zn–S (CGZS) alloyed nanorods compared with the binary Cu31S16 and ternary CuGaS2 nanocrystals. The L-shaped wurtzite CGZS nanorods with a uniform spatial composition distribution are synthesized via a non-injection solution approach for the first time. The successive incorporation of zinc and gallium ions into Cu31S16 seeds leads to formation of Cu31S16–ZnS and Cu31S16–CGZS heteronanostructures and finally results in the formation of single phase CGZS nanorods. The intrinsic features of L-shaped wurtzite CGZS nanorods offer efficient spatial charge separation and electrical transport, which contribute synergistically to the improved photocatalytic activity. This study provides a new way to develop novel multinary copper-based chalcogenides with flexible nanostructures for efficient photocatalytic hydrogen production.
✓ 已验证
产品关联
DOI
高影响因子
Nanoscale Research Letters
·
2015
·Vol. 10
·期 1
·1-6
·
IF 2.779
Guo Jing,Pei Yingli,Zhou Zhengji,Zhou Wenhui,Kou Dongxing,Wu Sixin
Solution-processed approach for the deposition of Cu 2 ZnSn (S,Se) 4 (CZTSSe) absorbing layer offers a route for fabricating thin film solar cell that is appealing because of simplified and low-cost manufacturing, large-area coverage, and better compatibility with flexible substrates. In this work, we present a simple solution-based approach for simultaneously dissolving the low-cost elemental Cu, Zn, Sn, S, and Se powder, forming a homogeneous CZTSSe precursor solution in a short time. Dense and compact kesterite CZTSSe thin film with high crystallinity and uniform composition was obtained by selenizing the low-temperature annealed spin-coated precursor film. Standard CZTSSe thin film solar cell based on the selenized CZTSSe thin film was fabricated and an efficiency of 6.4 % was achieved.
✓ 已验证
产品关联
DOI
PubMed
高影响因子
CHEMICAL ENGINEERING JOURNAL
·
2015
·
IF 4.321
Sheng Deng,Guangshan Zhang,Xi Wang,Tong Zheng,Peng Wang
Polyacrylonitrile fiber immobilized with iminodiacetic acid (IDA) was prepared under microwave irradiation and was used to adsorb Cu(II) and Hg(II) in aqueous solution. Synthesis conditions such as time, temperature and ratio of solvents were exploited systematically by orthogonal experiment and the properties of this fibrous absorbent were characterized by fourier transform infrared spectroscopy (FT-IR), elemental analysis (EA), scanning electron microscopy (SEM). The adsorption performances, in both thermodynamic and kinetic conditions, were investigated strictly and the experimental data fitted the Langmuir model ( R 2 > 0.99) and pseudo-second-order equation very well. The effect of pH on the adsorption capacity of metal ions was discussed and the optimal value for Cu(II) and Hg(II) was found to be 5.0 and 2.0, respectively. Thermodynamic parameters reveal the spontaneous and endothermic nature of the adsorption process , due to the negative value of standard free energy (Δ G ) and the positive value of standard enthalpy (Δ H ). The adsorption capacities toward Cu(II) and Hg(II) on the modified polyacrylonitrile fibers under microwave irradiation are higher than those on other adsorbents through conventional heating. The less consumed time and high grafting rate of the functional groups may be attributed to thermal effect as well as non-thermal effect of microwave irradiation.
✓ 已验证
产品关联
DOI
高影响因子
Science China-Materials
·
2015
·Vol. 58
·期 9
·693-703
·
IF 0
Liu Jian,Zhao Yuheng,Liu Jialong,Wang Shouguo,Cheng Yan,Ji Muwei,Zhou Yuanmin,Xu Meng,Hao Weichang,Zhang Jiatao
Heterovalent doping represents an effective method to control the optical and electronic properties of semiconductor nanocrystals (NCs), such as the luminescence and electronic impurities (p-, n-type doping). Considering the phase structure diversity, coordination varieties of Cu atoms in Cu 2 S NCs, and complexity of Cu doping in II-VI NCs, monodisperse Cu 2 S NCs with pure hexagonal phase were synthesized firstly. Then through cation exchange reaction between Cd ions and well-defined Cu 2 S NCs, dominant Cu(I) doped CdS NCs were produced successfully. The substitutional Cu(I) dopants with controllable concentrations were confirmed by local atom-specific fine structure from X-ray absorption near edge structure (XANES), extended X-ray absorption fine structure (EXAFS) spectroscopy, elemental analysis characterizations from X-ray photoelectron spectroscopy (XPS) and the electron spin resonance (ESR) measurement. The dominant and strong Cu(I) dopant fluorescence was verified by their absorption and photoluminescence (PL) spectra, and PL lifetime. Finally, the band positions and the p-type conductivities of the as-prepared Cu 2 S and Cu(I) doped CdS NCs were identified by ultraviolet photoelectron spectroscopy (UPS) measurements. The high monodispersity of NCs enables their strong film-scale self-assembly and will hasten their subsequent applications in devices.
✓ 已验证
产品关联
DOI
ENVIRONMENTAL SCIENCE AND POLLUTION RESEARCH
·
2015
·Vol. 23
·期 2
·1460-1470
·
IF 2.828
Chen Wei-fang,Zhang Jinghui,Zhang Xiaomao,Wang Weiya,Li Yuxiang
Nano-zero-valent iron/activated carbon (nZVI/AC) composite was evaluated for its effectiveness in the stabilization of Cu, Pb, Cd, and Cr in dredged river sediment. Synthetic precipitation leaching procedure (SPLP) and toxicity characteristic leaching procedure (TCLP) were adopted to compare the effects of nZVI/AC dosage, particle size, time duration, and temperature on heavy metal leachability. The results show that leachability dropped considerably with the addition of nZVI/AC and powdered particles in the size of 0.075–0.18 mm was more effective in stabilization than granular ones. Stabilization effect was stable in long-term and robust against changes in temperature. Tessier sequential extraction revealed that heavy metals were associated with solid particle, inorganic or organic matters in sediment. The addition of nZVI/AC was able to convert relatively weakly bound heavy metals into more strongly bound species and thus reduce the bioavailability and toxicity. Also, the standard potential of heavy metals may decide the mechanism of stabilization process.
✓ 已验证
产品关联
DOI
PubMed
高影响因子
ANALYTICAL BIOCHEMISTRY
·
2015
·
IF 2.219
Fang Wang,Wencheng Gong,Lili Wang,Zilin Chen
Selective recognition of d -tryptophan ( d -Trp) in the presence of Cu(II) was investigated at poly- l -lysine (p-l-Lys) film using electrochemical impedance spectroscopy (EIS) and differential pulse voltammetry (DPV). p-l-Lys film was immobilized on a glassy carbon electrode (GCE) by cyclic voltammetry between 0.0 and 1.9 V in 20 mM phosphate buffer solution (pH 8.6). After the p-l-Lys/GCE electrode was incubated with d -Trp solution containing Cu(II) ions, obvious enhancement of electron transfer resistance and decrease of voltammetric current could be observed. If d -Trp was replaced by l -tryptophan (l-Trp), there was no apparent resistance and current changes. Moreover, no resistance and current changes could be found in the absence of Cu(II). It may be due to the formation of Cu complex with l -lysine and d -tryptophan. Finally, this method was successfully applied to monitoring enantiomeric composition of the d -Trp and l-Trp mixtures.
✓ 已验证
产品关联
DOI
PubMed
高影响因子