Polymer-Plastics Technology and Materials
·
2021
·
IF 2.371
Dina F. Katowah,Gharam I. Mohammed,Waheed A. Adeosun,Abullah M. Asiri,Mahmoud A. Hussein
This paper reports an electrochemical sensor developed based on cross-linked polyaniline/(chitosan-oxidized single-walled carbon nanotube-graphene oxide/copper oxide) nanocomposite (C-PANI/(OXSWCNTs-GO-CS)/CuO NCs) for detection of a 4-chlorophenol (4-CP). The NCs synthesized by an in-situ chemical polymerization method and characterized by various techniques include XRD, FTIR, SEM-EDX, HR-TEM, TGA-DTG, DTA and cyclic voltammetry. A 4-CP selective electrochemical sensor was fabricated by coating a glassy carbon electrode (GCE) with synthesized NCs. The experimental results reported here displayed the good electrochemical property toward 4-CP oxidation with a detection limit of 0.13 µM (S/N = 3) and good current stability. It also had an impressive percent recovery of the spiked 4-CP in real environmental samples. The improved sensing performances were attributed to the formation of the network structure of C-PANI/(OXSWCNTs-GO-CS)/CuO NCs. Therefore, this study presents a sensitive and promising 4-CP electrochemical sensor for water quality management and human health protection.
✓ 已验证
产品关联
DOI
高影响因子
COLLOIDS AND SURFACES A-PHYSICOCHEMICAL AND ENGINEERING ASPECTS
·
2021
·
IF 4.539
Yingzhen Zhang,Jingchuang Zhao,Xianyu Kang,Guoliang Chen,Yancai Li
Currently, Substituting methanol oxidation reaction with a low theoretical potential for water oxidation reaction is one of the hotspots in the study of water splitting to hydrogen production . In this work, N-C/NiO nanocomposites with different morphologies were synthesized by one-pot hydrothermal method . Interestingly, the tremella-like N-C/NiO nanocomposites turned into looser flower-like structure at the existence of N-C-SiO 2 nanosheets supporting in the hydrothermal process. Meanwhile, the silica in the N-C-SiO 2 nanosheets was removed by urea in hydrothermal reaction. The introduction of the N-C-SiO 2 nanosheets has a vital influence to enhance the electrochemical performance of the N-C/NiO nanocomposites. The flower-like N-C/NiO nanocomposites exhibit large electrochemically active surface area and superior electrocatalytic performance for methanol oxidation reaction (MOR) in alkalic electrolyte. It displays excellent electrocatalytic activity with a highly mass activity (3298 mA mg −1 ) and long-time stability (remain 50% after 36,000 s) toward MOR, which are 35.0 and 2.9 folds higher than that of the commercial 10%-Pt/C, respectively.
✓ 已验证
产品关联
DOI
高影响因子
MICROCHIMICA ACTA
·
2021
·Vol. 189
·期 1
·1-10
·
IF 5.833
Xing Yanyan,Chen Meiling,Zhao Yunkun,Xu Jiabi,Hou Xiaohong
Novel Fe 3 O 4 @C@MnO 2 composites were successfully synthesized for the first time via an interfacial reaction between magnetic porous carbon and KMnO 4 , in which the magnetic porous carbon was derived from the pyrolysis of Fe-MIL-88A under N 2 atmosphere. Interestingly, the obtained Fe 3 O 4 @C@MnO 2 composites were found to have triple-enzyme mimetic activity including peroxidase-like, catalase-like, and oxidase-like activity. As a peroxidase mimic, Fe 3 O 4 @C@MnO 2 composites could catalyze the oxidation of TMB into a blue oxidized product by H 2 O 2 . As a catalase mimic, Fe 3 O 4 @C@MnO 2 could catalyze the decomposition of H 2 O 2 to generate O 2 and H 2 O. As an oxidase mimic, Fe 3 O 4 @C@MnO 2 could catalyze the direct oxidation of TMB to produce a blue oxidized product without H 2 O 2 . Reactive oxygen species measurements revealed that the oxidase-like activity originated from 1 O 2 and O 2 − ∙and little∙OH generated by the dissolved oxygen, which was catalyzed by the Fe 3 O 4 @C@MnO 2 in the TMB oxidation reaction. The oxidase-like activity of Fe 3 O 4 @C@MnO 2 was investigated in detail. Under the optimized conditions, a rapid, sensitive, visual colorimetric method for dopamine detection was developed based on the inhibitory effect of dopamine on the oxidase-like activity. The proposed method allows for dopamine detection with a limit of detection of 0.034 μM and a linear range of 0.125–10 μM. This new colorimetric method was successfully used for the determination of dopamine in human blood samples. Graphical abstract
✓ 已验证
产品关联
DOI
PubMed
高影响因子
Reaction Chemistry & Engineering
·
2021
·Vol. 6
·期 10
·1900-1910
·
IF 4.239
Udayakumar Veerabagu,Gowsika Jaikumar,Fushen Lu,Franck Quero
Copper iodide (CuI) nanoparticles/boron nitride nanosheets (BNNSs) were prepared via an ultrasonication method and subsequently characterized. For the first time, these newly synthesized CuI/BNNS supports were used as heterogeneous catalysts for C–H difluoromethylation reactions, including the synthesis of heteroarenes and terminal alkynes. The versatility of the catalyst was demonstrated for the synthesis of diverse substituted difluoromethylated heteroarenes and terminal alkynes from electron-deficient and electron-rich groups, resulting in moderate to high yields (up to 91%). The reaction was carried out in a greener medium (cyrene instead of dimethylformamide and N-methyl-2-pyrrolidone) at room temperature using (difluoromethyl)trimethylsilane and 9,10-phenanthraquinone in the presence of the CuI/BNNS catalyst containing ∼3 wt% Cu and I. Notably, its activity was found to provide higher yield, shorter reaction time, and fewer usage of the catalyst, compared with commercial CuI catalysts. In addition, the CuI/BNNS catalyst could be easily recovered and recycled up to five times, with only a slight decrease (3%) in its catalytic activity, providing attractive features for chemical engineers to use this catalyst for the large-industrial scale synthesis of organic bioactive compounds involving C–H difluoromethylation reactions.
✓ 已验证
DOI
高影响因子
JOURNAL OF ALLOYS AND COMPOUNDS
·
2021
·
IF 5.316
Xinyue Liu,Hongwei Zhao,Shan Jiang,Shuai Wu,Tong Zhao,Lixiang Li,Xin Geng,Haiming Yang,Weimin Zhou,Chengguo Sun,Yiqing Chen,Baigang An
Both SiC and porous carbons have been widely used in the fields of catalysts, ceramics, electrode materials and electromagnetic materials since their advantages of excellent chemical and thermal stability, good conductivity, flexibility and stiffness. However, pore construction of SiC still faces considerable difficulty comparing to carbon materials with a large variety of pores. Herein, by developing a novel method combining the silanization of SBA-15 template, acetylene CVD and magnesiothermic reduction reaction (MRR) technology, a novel porous material of OM-SiC@OMC that the ordered mesoporous SiC interfaces with the ordered mesoporous carbon has been successful synthesized. The silanization enhances the activity of carbon deposition into the pores of SBA-15 template, MRR results in the formation of SiC between the interface of SiO 2 and carbon. After the template removal, a novel mesoporous composite material of OM-SiC@OMC has been successfully obtained. Interestingly, OM-SiC@OMC contains two types of ordered mesopores interfacing with each other by the pore wall of SiC phase and carbon phase, respectively. As electrode materials of supercapacitors , OM-SiC@OMC exhibits a capacitance of 194.8 F g −1 with an excellent retention rate of 97.8% after 10,000 cycles. The present study explores a novel ordered porous materials constructed by the interfaced pores of carbon and carbide , it is promising to find good applications of these multi-interfaced porous materials.
✓ 已验证
产品关联
DOI
高影响因子
NANOTECHNOLOGY
·
2021
·Vol. 32
·期 30
·305402
·
IF 3.874
Yaqi Cui,Jiaoxing Xu,Yi Zhao,Lunhui Guan
The utilization of earth abundant iron and nitrogen doped carbon as a precious-metal-free electrocatalyst for oxygen reduction reaction (ORR) significantly depends on the rational design and construction of desired Fe−Nx moieties on carbon substrates, which however remains an enormous challenge. Herein a typical nanoporous nitrogen-rich single atom Fe−N/C electrocatalyst on carbon nanotube (NR-CNT@FeN-PC) was successfully prepared by using CNT as carbon substrate, polyaniline (PANI) and dicyandiamine (DCD) as binary nitrogen sources and silica-confinement-assisted pyrolysis, which not only facilitate rich N-doping for the inhibition of the Fe agglomeration and the formation of single atom Fe−Nx sites in carbon matrix, but also generate more micropores for enlarging BET specific surface area (up to 1500 m2·g−1). Benefiting from the advanced composition, nanoporous structure and surface hydrophilicity to guarantee the sufficient accessible active sites for ORR, the NR-CNT@FeN-PC catalyst under optimized conditions delivers prominent ORR performance with a half-wave potential (0.88 V versus RHE) surpass commercial Pt/C catalyst by 20 mV in alkaline electrolyte. When assembled in a home-made Zn−air battery device as cathodic catalyst, it achieved a maximum output power density of 246 mW·cm−2 and a specific capacity of 719 mA·h·g−1Zn outperformed commercial Pt/C catalyst, holding encouraging promise for the application in metal-air batteries.
✓ 已验证
产品关联
DOI
PubMed
高影响因子
ENERGY & FUELS
·
2021
·
IF 3.605
Kai Fang,Liujia Ma,Ya-Jun Cheng,Senlin Xia,Zhaohui Yang,Xiuxia Zuo,Lianmin Ji,Jie Gao,Peter Müller-Buschbaum,Yonggao Xia
Silicon anode has a huge potential to replace graphite anode. Nevertheless, it shows poor long-term cyclic stability and rate capability due to a huge volume change upon lithiation and intrinsic semiconductor property. In this manuscript, a silicon composite with nonagglomerated super-small sized copper nanoparticles (average diameter: 7 nm) was obtained. First, the super-small copper nanoparticles (NPs) are beneficial to enhance the electron conductivity and electrochemical kinetics. Second, the copper NPs help to stabilize the electrode by absorbing mechanical stress. An amine based curing agent works as not only the solvent but also the carbon precursor. The thermosetting epoxy resin inhibits the agglomeration of the copper and silicon nanoparticles. Both silicon and copper nanoparticles are homogeneously dispersed in the carbon formed during the calcination under an inert atmosphere. The influence of the silicon and copper contents on the composition, structure, morphology, crystallinity, porosity, dispersion, and electrochemical performance of the Si/Cu/C nanohybrids are thoroughly studied by various techniques. The structure–property correlation of Si/Cu/C nanohybrids is investigated. A good balance among capacity, cyclic stability, and rate performance is achieved.
✓ 已验证
产品关联
DOI
高影响因子
NEW JOURNAL OF CHEMISTRY
·
2021
·Vol. 45
·期 15
·6865-6871
·
IF 3.591
Pengcheng Li,Enze Xu,Jiamin Zhang,Lei Chen,Zhenjie Sun,Li Wang,Yang Jiang
Transition metal sulfides (TMSs), especially cobalt-based sulfides have great potential use in battery anode materials. However, low coulombic efficiency and poor cycle stability limit their application in battery fabrication. In this work, a two-dimensional MOF material ZIF-9 was treated by a two-step calcination method that obtained a flower-shaped carbon skeleton coated with Co-vacancy, Co1−xS nanoparticles. The skeleton effectively restrains the volume expansion that happens on electrodes, which improved the electrical conductivity of the compound. The cobalt vacancy changes the local electronic structure and atomic populations; the DFT calculation also proves that this structure is beneficial to the migration of sodium ions and provides good cycling performance under high current density. According to our electronic experiments, Co1−xS@C exhibited good electrochemical performance, which maintains a capacity of about 300 mA h g−1 at a high current density of 5 A g−1 after 250 cycles. All results indicate the outstanding electrochemical performance of our composite material, especially under a high current density. This work may provide a method in MOFs-derived TMSs compounds to stimulate the potential of transition metal sulfide materials in energy storage.
✓ 已验证
产品关联
DOI
高影响因子
CHEMICAL ENGINEERING JOURNAL
·
2021
·
IF 13.273
Liyuan Duan,Guoqiang Li,Shuting Zhang,Hongyu Wang,Yongle Zhao,Yongfa Zhang
In this study, graphitized carbon nitride photocatalysts were successfully prepared by using the desulfurized waste liquid extracting salt from coking plants. The NO x removal efficiency of g-C 3 N 4 synthesized using ammonium thiocyanate (NH 4 SCN), ammonium thiosulfate ((NH 4 ) 2 S 2 O 3 ) and ammonium sulfate ((NH 4 ) 2 SO 4 ) with different mass ratios were evaluated. The results showed that due to the addition of (NH 4 ) 2 S 2 O 3 and (NH 4 ) 2 SO 4 a large amount of sulfur-containing gas was released during pyrolysis, which significantly increased the specific surface area and pore volume of the photocatalysts. The release of sulfur-containing gas also resulted in the incorporation of sulfur, and due to this doping process the band gap of the photocatalyst was widened to 2.94 eV, thus enhancing its visible light response. C vacancies were formed in the hepazine ring, which increased the electron density around the N–(C) 3 bridge bond and formed an electron trapping center, thus inhibiting the recombination of charge carriers. The photocatalysts had increased O 2 adsorption capacity and increased number of amino groups on their surface. This facilitated the rapid generation and consumption of reactive oxygen species, inhibited the accumulation of NO 2 on the surface, reduced the production of NO 2 , thus improving the NO x removal efficiency of the photocatalysts. The principle of using “waste for waste control” was achieved, and a new method for nitrogen oxide removal was provided.
✓ 已验证
产品关联
DOI
高影响因子
CHEMICAL ENGINEERING JOURNAL
·
2020
·
IF 10.652
Zhiyan Huang,Pingxiao Wu,Chenhui Liu,Meiqing Chen,Shanshan Yang,Zhi Dang,Nengwu Zhu
Understanding the origin of high activity of graphene layers encapsulated Fe-N-C catalysts in Fenton-like reaction is critical, but still challenging for developing catalysts with high activity and durability. Therefore, we prepared a highly active Fe-N-C catalyst (Fe x Mn y -Fe@NCs) containing FeN 4 coordination to activate peroxymonosulfate (PMS) toward 4-aminobenzoic acid ethyl ester (ABEE) degradation, and revealed the multiple catalytic reaction sites by investigating the composition and the structure of the catalyst. The relationship between the catalytic degradation performance and multiple catalytic reaction sites was performed on the basis of both experiments and density functional theory (DFT) calculations. The catalytic performance of Fe 2 Mn 1 -Fe@NCs was found to show optimal catalytic degradation performance. Pyrrolic N served as adsorption site as well as singlet oxygen generation site to promote the catalytic degradation. Fe-pyridinic N-C acted as hydroxyl radical and sulfate radical generation site. Both singlet oxygen and superoxide radical were dominated the catalytic reaction. The insight achieved from this study may be further applied to other Fe-N-C catalysts design and further efficient organic pollution remediation.
✓ 已验证
产品关联
DOI
高影响因子
TALANTA
·
2020
·
IF 5.339
Dandan Song,Jing Zheng,Nosang V. Myung,Jingli Xu,Min Zhang
A sandwich-type electrochemical immunosensor was developed for the detection of CEA where hollow magnetic silica coated nickel/carbon (Ni/ [email protected] 2 ) nanocomposites was used as an immobilized carrier and gold nanoparticle-coated PANI microsphere ( [email protected] @Au) as electrochemical transducer. Magnetic assembly of Ni/ [email protected] 2 nanocomposites allow easy separation and assembly which eliminates the further modification process. In addition, the prepared [email protected] @Au possess good biocompatibility, and electrical conductivity. The fabricated immunosensor show excellent sensing performance including a wide dynamic range from 0.006 to 12.00 ng mL −1 and low detection limit at 1.56 pg mL −1 . Moreover, this sensor shows superior selectivity with excellent reliability and reproducibility which might lead into easier implementation in clinical setting.
✓ 已验证
产品关联
DOI
PubMed
高影响因子
CHEMICAL ENGINEERING JOURNAL
·
2020
·
IF 10.652
Yi Wang,Chuangchuang Liu,Shaofeng Zhou,Rui Hou,Lihua Zhou,Fengyi Guan,Renlian Chen,Yong Yuan
Three-dimensional (3D) nano-structure materials with a large bacterial accessible specific area have emerged as promising electrode materials for bioelectrochemical systems (BESs), achieving high bioelectricity outputs. However, it remains a challenge that biofilms with increased thickness inhibit substrate diffusion into the 3D nano-structure during long-term operation of BESs, causing a reduction in bioenergy output. Herein, an innovative ordered 3D nano-structure electrode was fabricated by growing self-supported N-doped C/Fe 3 O 4 -nanotube composite arrays onto carbon fiber cloth ( [email protected] /Fe 3 O 4 ), using template-based deposition coupled with thermal reduction/carbonization methods. The fabricated [email protected] /Fe 3 O 4 electrode was applied as a bioelectrode in a conventional three-electrode BES and as an anode in microbial fuel cell (MFC), while their capacity to improve bioelectricity generation was assessed. Results indicate that the hierarchical N-doped C-coated nanotube arrays not only significantly enhanced conductivity and areal capacitance of the electrode, but also reduced its charge transfer resistance and provided the 3D open nano-structure with excellent biocompatibility for microbial colonization and internal diffusion of the culture substrate. Consequently, a high maximum current density (4.11 mA/cm 2 ) and coulombic efficiency (~89%) was obtained from the [email protected] /Fe 3 O 4 electrode after about 3 months of BES operation, exhibiting higher biocatalytic performance and extracellular electron transfer efficiency than the original carbon fiber cloth (CC, 1.89 mA/cm 2 ). Moreover, MFC equipped with [email protected] /Fe 3 O 4 anode produced a maximum power density of 1.21 ± 0.04 W/m 2 , which was 2.1 times higher than CC (0.58 ± 0.03 W/m 2 ). This study demonstrates the outstanding advantages of [email protected] /Fe 3 O 4 nanotube composite arrays assembled on CC, making it a potential alternative to existing 3D electrodes for high-performance BES applications.
✓ 已验证
产品关联
DOI
高影响因子