CHEMICAL ENGINEERING JOURNAL
·
2019
·
IF 8.355
Jing Zeng,Dongzheng Wu,Xin Wang,Junnan Wu,Jiyang Li,Jing Wang,Jinbao Zhao
The high-voltage cathode material based on the sodium super ionic conductor (NASICON) structured Na 3 V 2 (PO 4 ) 3 (NVP) has been found to be a potential candidate for Mg storage. In this work, to improve its electrochemical performance, we construct honeycomb-like structured NVP/C/G with faster electronic and ionic transport by a convenient and universal spray-drying method for the first time. After electrochemically desodiating two Na from the NVP/C/G (ED-NVP/C/G), the ED-NVP/C/G is tested in highly anhydrous Mg electrolyte, and the insights into its Mg storage property and mechanism are carefully studied. An initial capacity of 87 mAh g −1 with a relatively high average discharge voltage of 2.47 V vs. Mg 2+ /Mg is obtained at 0.1 C. The X-ray diffraction (XRD) results show that the inserted Mg 2+ ions tend to occupy the Na2 (at 18e sites) vacant sites. The investigation of kinetic process by galvanostatic intermittent titration technique (GITT) reveals that the Mg diffusion kinetics is faster during the demagnesiation process. The electrochemical reaction bases on two-phase transition mechanism, and the R ct value shows a positive relationship to the formation of NaV 2 (PO 4 ) 3 phase. Finally, a Mg full cell prototype based on the ED-NVP/C/G cathode with Mg metal anode is built. The rational structure design of NVP/C/G improves the electrochemical performance for Mg storage, and our work also gives new understanding into the Mg storage mechanism in the ED-NVP/C/G structure.
✓ 已验证
DOI
高影响因子
JOURNAL OF ELECTRONIC MATERIALS
·
2017
·Vol. 47
·期 1
·96-102
·
IF 1.579
Wang Yan,Han Jing,Wang Yishu,Ma Limin,Guo Fu
With a body-centered tetragonal crystal structure, Sn grains were demonstrated to have highly anisotropic behaviors in various properties. The electromigration behavior of lead-free solder was impacted by the grain orientations. In this paper, the angle between the c -axis and the electron flow direction in composite solder joints (angle θ ) was proven to be an important factor during electromigration. The effects of angle θ on the electromigration of composite solder joints were investigated in this paper. Cu particle-reinforced Sn3.5Ag solder joints were stressed under a current density of 10 4 A/cm 2 at room temperature. After 336 h current stressing time, different electromigration phenomena occurred at the two sides of the grain boundary in the composite solder joint which contained two Sn grains with different angle θ . The Sn grains with the larger angle θ had a smaller growth rate of Cu 6 Sn 5 . In addition, a composite solder joint with a single Sn grain was set as the contrast and its angle θ was smaller than that of the composite solder joint with two Sn grains. The growth rate of Cu 6 Sn 5 in the composite solder joint with a single grain was faster than that of the composite solder joint with two Sn grains.
✓ 已验证
DOI
高影响因子
Journal of Cleaner Production
·
2024
·
IF 9.7
Ziyuan Li,Yangjun Wang,Huan Wang,Shuai Zhang,Zhen Shang,Limei Tian,Yuying Yan
Utilizing salt-based shape-stabilized phase change materials (ss-PCMs) for high-temperature thermal energy storage stands as a pivotal avenue in realizing carbon neutrality . However, the performance of ss-PCMs significantly deteriorates after thermal cycling. This study utilizes rice husk carbon (RHC) with an in-situ SiO 2 –C interconnected structure as the encapsulating material, along with expanded graphite (EG) and MgO , to encapsulate ternary chloride (TC). In this approach, RHC simultaneously acts as a thermal conductivity materials (TCM) and a ceramic supporting material (CCM). The results showed that this encapsulation method can effectively encapsulate up to 65% of TC. The 60 wt% TC-10 wt% RHC-10 wt% EG-20 wt% MgO sample named 60T/10R/10E/20M is considered a close to optimal formulation in terms of thermal conductivity and phase change enthalpy . This ss-PCM has a thermal conductivity of 8.86 W m−1 K−1, and phase change enthalpy of 153.6 J g−1. The ss-PCMs maintained shape stability even after 1000 cycles, with minimal mass loss and thermal conductivity degradation compared to the non-RHC-added ss-PCM. This study has prepared high performance and reliability thermal storage materials through a green and low-cost approach.
✓ 已验证
DOI
高影响因子
RSC Advances
·
2015
·Vol. 5
·期 125
·102993-102999
·
IF 3.84
Luyu Yang,Wei Liu,Huanlei Wang,Shuang Liu,Jifei Wang,Jiaxin Chen
A hierarchical pore structure is believed to be an excellent architecture for metal oxide anode materials of lithium-ion batteries (LIBs). However, the difficulty and complication in synthesis limit their further application. In this work, a novel Fe3O4/C composite with a hierarchical pore carbon (HPC) network has been synthesized simply by one-step pyrolysis synthesis using ferrous gluconate as the precursor. This hierarchical porous framework derived from a loose assembly of the intersecting porous carbon rods presents a wide range of pore sizes and a rather large surface area (>226 cm2 g−1). Embedded with well-crystalline Fe3O4 particles, the resulting Fe3O4@HPC composite exhibits a high capacity of 1112 mA h g−1 at the end of the 100th cycle and an enhanced rate performance of above 600 mA h g−1 at a high current density of 2000 mA g−1. This might derive from the unique hierarchical pore system with a high overall porosity, which can not only facilitate the electrolyte diffusion but also alleviate severe volume variation efficiently in lithium ion insertion/extraction. More importantly, this provides us with a successful example to fabricate advanced anode materials simply by one-step pyrolysis of cheap organic–inorganic hybrids at low-cost.
✓ 已验证
DOI
高影响因子
ELECTROCHIMICA ACTA
·
2015
·
IF 4.504
Yan Li,Defa Huang,Wenjiang Shen
Supercapacitors based on MnO 2 /CB/C nanocomposites films are prepared by direct electrophoretic deposition (EPD) process on nickel plates in an aqueous solution containing of MnO 2 nanoparticles , carbon black (CB) and sodium alginate (SA), followed by carbonization of SA to carbon layer . The nanocomposites of MnO 2 /CB/C films are prepared from different electrolytic solutions with mass ratios of MnO 2 nanoparticles, CB and SA from 8: 1: 1 to 6: 2: 2. Same mass ratios of nanocomposites are prepared by traditional Doctoral Blade (DB) process for morphologies and performances comparisons, in which mixtures of MnO 2 nanoparticles, carbon black with polyvinylidene fluoride (PVDF) are used. From scanning electron microscopy (SEM) and high resolution transmission electron microscopy (HRTEM) images, the MnO 2 /CB/C shows a uniform aggregation of MnO 2 and carbon nanoparticles covered with carbon layers. In the case of the MnO 2 /CB/PVDF from DB process, the MnO 2 nanoparticles are separately clustered, and the clusters are adhered to CB together with PVDF. More uniform film and better contact of MnO 2 with CB by carbon layer can be obtained from EPD/Carbonization process. The electrochemical performances of MnO 2 /CB/C and MnO 2 /CB/PVDF nanocomposites in different mass ratios are compared by areal specific capacitances (C a ), charge transfer resistance of films and retention of capacitance after 1500 cycles of charge/discharge to test stability respectively. The nanocomposites of MnO 2 /CB/C show better areal specific capacitances and smaller charge transfer resistances at each ratio. The carbon layer coating on surface of MnO 2 nanoparticles can effectively delay the capacitance loss, which leads to 98% of capacitance after charge/discharge cycles, much better than retention of those from DB process (50%). The EPD/Carbonization is an easy way to make carbon layer on pseudo capacitive materials from sodium alginates , and the carbon layer can effectively improve the charge/discharge stability of supercapacitors.
✓ 已验证
DOI
高影响因子
JOURNAL OF ALLOYS AND COMPOUNDS
·
2022
·
IF 6.371
Wangwu Li,Jiao Peng,Hui Li,Zhenyu Wu,Baobao Chang,Xiaowei Guo,Gairong Chen,Xianyou Wang
Si-based anodes have revealed the potential as the next generation of lithium ion battery anode material , whereas the poor conductivity and huge volume changes during (de)lithiation process of silicon still limit their practical application. Herein, the Si/nitrogen doped carbon layer/carbon framework microspheres (SCM) are designed by nano-Si via electro-spray technology as anodes for lithium ion batteries. It has been found that the SCM consists of individual carbon-coated nano-Si primary particles linked by PAN framework, in which the carbon buffer layer can further absorb the stress of volume changes during charge/discharge process, and the carbon framework carbon framework not only provides fast diffusion path of electron, but also effectively reduces the consumption of electrolyte. Therefore, the initial columbic efficiency (ICE) of SCM anode can reach as high as 72%, and the SCM anode also shows a high specific capacity of 1192 mAh g −1 at 0.2 A g −1 and keeps a reversible capacity of 746 mAh g −1 after 200 cycles, demonstrating the as-designed SCM possesses an high ICE and a good electrochemical performance. This strategy provides a significant inspiration for fabricating high-performance Si/C anode materials of lithium-ion battery.
研究领域:
材料科学
·
储能
·
电化学
·
纳米技术
✓ 已验证
DOI
高影响因子
Journal of Environmental Chemical Engineering
·
2026
·Vol. 14
·期 5
·124731
·
IF 7.5
Nan Zhang,Menglin Gao,Wenru Cheng,Zhaocun Song,Xichen Yang
The development of efficient and cost-effective electrocatalysts for hydrogen production is crucial for advancing a carbon-neutral circular economy. The hydrogen evolution reaction (HER) performance of MoS 2 in alkaline media is hindered by its sluggish water-dissociation kinetics and inert basal planes. Herein, we report a novel ternary heterostructure, consisting of γ-FeOOH nanosheets and smaller Ni 3 S 2 nanosheets grown on vertical 1 T/2H MoS 2 nanosheets, that exhibits enhanced HER activity. Systematic investigations suggest that the enhanced HER performance is associated with the interfacial interactions among Ni 3 S 2 , γ-FeOOH, and MoS 2 , which involve strain coupling, electronic coupling, and functional synergy. Accordingly, the Ni 3 S 2 /γ-FeOOH/MoS 2 /CC electrode requires overpotentials of only 99.6 and 176.1 mV at 10 and 100 mAcm −2 , respectively. Remarkably, it outperforms commercial Pt/C at current densities exceeding 173.2mA cm −2 and requires an overpotential of only 213.9mV at 300 mA cm −2 , while also exhibiting robust operational stability at high current densities, highlighting its promise for further exploration toward practical alkaline water electrolysis systems. This work provides a promising strategy for designing high-performance, earth-abundant MoS 2 -based HER catalysts for alkaline water electrolysis.
✓ 已验证
产品关联
DOI
高影响因子
POLYMER
·
2026
·
IF 5.1
Xue Lin,Xiao Song,Yanan Yin,Xiaobing Ren,Xu Gao,Minghui Wang,Zhao Jin,Mingda Wen
1.Functional components were incorporated into polystyrene microspheres under surfactant-free conditions, simultaneously improving their monodispersity, optical stability, and functional reliability. • 2.The developed LICA-based CRP detection method exhibited good analytical performance, with stability bias ranging from -3.5% to 0.6%, relative bias for accuracy ranging from -1.0% to 0.7%, within-batch coefficients of variation ranging from 4.20% to 4.70%, and between-batch relative deviations ranging from -6.46% to 4.45%. • 3.Compared with the conventional Immunoassay Technology (IT) method, the LICA method showed good agreement, with 90% of measurements falling within the limits of agreement. C-reactive protein (CRP) is an important biomarker for diagnosing and therapeutic-monitoring inflammatory and cardiovascular diseases. Although the light-initiated chemiluminescent assay (LICA) enables rapid, highly sensitive homogeneous detection, its widespread applications are constrained by the stringent performance requirements for donor and acceptor microspheres. In this study, covalently integrated donor and acceptor microspheres were fabricated through a soap-free emulsion copolymerization strategy by incorporating 2-vinylthiophene, europium complexes, and a photosensitizer into a polystyrene matrix. Subsequently, oxidized dextran surface modification was introduced into the matrix to enhance biocompatibility and biomolecular conjugation efficiency. Thus obtained microspheres exhibited excellent mono-dispersity, high optical stability, and favorable surface characteristics for homogeneous immunoassays. The developed LICA-based CRP assay demonstrated satisfactory analytical performance, with a relative bias ranging from -1.0% to 0.7% for high-concentration samples and from -1.0% to 0.6% for low-concentration samples. The within-run precision showed a coefficient of variation ranging from 4.20% to 4.70%, with between-batch relative bias ranging from 4.45% to 6.46%, all of which satisfied a predefined acceptance criteria of < 8%. Compared with conventional immunoassay technology, the developed assay yielded a mean bias of -1.47 ng/mL, with 90% of measurements falling within the limits of agreement (-6.15 to 4.18 ng/mL), which demonstrates good consistency between the two assays. The developed microspheres provide a reliable material platform for homogeneous LICA and offer a promising potential for clinical applications of CRP detection. Download: Download high-res image (421KB) Download: Download full-size image
✓ 已验证
DOI
高影响因子
CHINESE JOURNAL OF STRUCTURAL CHEMISTRY
·
2026
·
IF 10.5
Xingyu Li,Jian Peng,Zihao Xu,Wanyuan Li,Biao Xu,Chunyu Li,Wubin Dai
Simultaneous realizations of high thermal stability and quantum efficiency (QE) in phosphors with near-infrared (NIR) photoluminescence (PL) and long-persistent PL (LPL) attributes are a daunting task. Herein, we have come up with a dual-site co-substitution scheme in Ca 3 Sc 2 Ge 3 O 12 : Cr 3+ /Ni 2+ to concurrently actualize high-quality NIR-I/II (L)PL via either equivalent or aliovalent co-substitution at indirect lattice A/C sites of [Y 3+ + Al 3+ ] or [Y 3+ + Si 4+ ] for [Ca 2+ + Ge 4+ ]. Both Cr 3+ and Ni 2+ are colonized at B site (Sc 3+ ) under weak crystal field environment and emitting continuous PL across NIR-I/II regions via energy transfer from Cr 3+ to Ni 2+ under blue-light excitation. Due to inequivalent replacement of Ni 2+ at Sc 3+ site and consequential production of defects, a charming NIR LPL is also gained. Further incorporation of [Y 3+ + Al 3+ ] unit begets densified robust framework with [Sc(Cr/Ni)O 6 ] octahedral distortion, elucidating the mechanism of improved properties in PL QE (76.23%) and stability (89.5%@423 K). While [Y 3+ + Si 4+ ] modulation in Ca 3 Sc 2 Ge 3 O 12 not only brings rigid structure but also suppresses defects (LPL) because of equivalent triple-unit between Y 3+ /Si 4+ /Ni 2+ and Ca 2+ /Ge 4+ /Sc 3+ . A NIR pc-LED based on the designed phosphor with a commercial 460 nm blue LED chip is fabricated and reveals multi-applications in nondestructive detection, bioimaging, and anticounterfeiting. This work provides new perspectives for developing high-performance NIR-emitting phosphor materials. This study reveals the state-of-the-art researches on both NIR-I/II-emitting (L)PL phosphors with high QE and thermal stability from Cr/Ni-activated in garnet Ca 3 Sc 2 Ge 3 O 12 and their multiple applications in the NIR pc-LED, non-destructive detection, and anticounterfeiting. The proposed A/C-site regulation and ET from Cr to Ni pave a new way to design NIR-I/II phosphor and expands their related optoelectronic applications. Download: Download high-res image (298KB) Download: Download full-size image
✓ 已验证
DOI
高影响因子
PROCESS SAFETY AND ENVIRONMENTAL PROTECTION
·
2026
·
IF 7.9
Pengfei Wang,Chuanhui Geng,Li Shao,Mei Liu,Qian Li,Kecun Ma,Zhi Chen,Qingguo Chen
Water pollution has been worsened by increasing human activities, involving both water-soluble and non-water-soluble contaminants. In this study, a Fe-N-C@ZnO activated PS-AOP (persulfate advanced oxidation process) system was developed through the combination of photocatalysis and PS (persulfate) activation for pollutant degradation in freshwater and seawater. First, the optimal performance was determined by adjusting the Fe-N-C@ZnO to PS ratio, with the best results achieved at 5:3. The degradation efficiency and mechanisms were then examined across different pollutant types. Higher degradation rates were observed in the Fe-N-C@ZnO activated PS-AOP system compared to PS alone, in freshwater, improvements of 70.87%, 61.63%, and 46.26% were recorded for enrofloxacin (ENR), naphthalene, and crude oil, respectively. And in seawater, the increases were 57.53%, 46.87%, and 31.49%. Through radical quenching experiments, h⁺, e⁻, and SO 4 ·⁻ were identified as the dominant reactive species. Additionally, DI-MS analysis was used to propose four degradation pathways for ENR (three Piperazine-Routes and one Quinolone-Route) and two pathways for naphthalene (Benzene ring hydroxylation and Tautomerization). Download: Download high-res image (198KB) Download: Download full-size image
✓ 已验证
DOI
高影响因子
POLYMER
·
2026
·
IF 5.1
Yuzeng Li,Zhen Fan,Zhenyu Feng,Zixiang Xu,Nurimangul Muntiza,Yi Ru,Qinran Li,Hongfeng Zhang,Jin Zhao,Qiliang Deng,Donglan Sun,Tianjun Liu
A novel strategy for cytochrome c (Cyt c) selective recognition with the epitope imprinting and host-guest interaction dual-mechanism recognition was developed via reversible addition-fragmentation chain transfer polymerization regulated by a cucurbit[6]uril-functionalized chain transfer agent (CB[6]-CPAD). CB[6]-CPAD attaches to N-terminal epitope GI-9 through host-guest interactions between cucurbit[6]uril and lysine-residue. It regulates the imprinted polymers via the modulatory effect of disulfide esters, thereby enhancing the accessibility of cucurbit[6]uril within the imprinted sites. After polymerization and template removal, the imprinted particles exhibited well binding affinity for GI-9 (8.40 mg⋅g -1 , IF = 1.62) and Cyt c (11.32 mg⋅g -1 , IF = 1.62) at 45°C and obvious selective recognition of Cyt c over other proteins with a significantly higher IF, which were driven by the combination of molecular imprinting and host-guest interactions. It indicated that the construction of temperature-sensitive dual-mechanism recognition combining epitope imprinting and host-guest interactions can effectively achieve selective recognition of the target protein.
✓ 已验证
DOI
高影响因子
Microbiology Spectrum
·
2026
·
IF 4.1
Xueqing Zhao,Yucheng Shi,Wenzhuo Tian,Yutong Tian,Chuxiao Hu,Ziye Guo,Ting Ma,Guoqiang Li,Ge Gao
Cyclic di-GMP (c-di-GMP) acts as a bacterial second messenger that regulates various physiological processes, including biofilm formation, motility, and virulence. It is synthesized by diguanylate cyclases (DGCs) and degraded by phosphodiesterases (PDEs), with precise regulatory effects typically requiring the coordinated action of multiple DGCs and PDEs. Kosakonia oryzendophytica FY-07 (FY-07) exhibits high bacterial cellulose (BC) yield, rapid growth, and robustness and can produce BC under varying oxygen conditions; however, the underlying mechanism driving the phenotypic transition from cellulose-producing to motile states during fermentation has yet to be elucidated. In this study, we aimed to identify two DGCs, KoBdcA and KoBdcB, and one PDE, KoBpdA, whose encoding genes are located adjacent to the cellulose synthesis operon in FY-07. KoBdcA and KoBpdA form an antagonistic DGC-PDE pair that maintains intracellular c-di-GMP homeostasis. Deletion of either gene alters BC production and motility. In contrast, KoBdcB acts as an auxiliary component, and its deletion alone causes no phenotypic changes. KoBdcA regulates BC synthesis via an indirect interaction with BcsA mediated by KoBdcB. The Per-Arnt-Sim (PAS) domains of KoBdcA and KoBpdA bind hemin, enabling them to sense oxygen and modulate their enzymatic activities. Elevated DGC activity during early fermentation promotes BC production, while increased PDE activity later suppresses BC synthesis, shifting cells to a motile state.
✓ 已验证
产品关联
DOI
PubMed
高影响因子