Energy & Environmental Materials
·
2026
·
IF 14.1
Rilong Yang,Yuying Yang,Qianwen Liu,Qiuhua Feng,Jianyu Wu,Yan Yu
Solar interfacial evaporation, featuring no extra energy need and low equipment demand, offers a promising off-grid desalination solution to alleviate global freshwater shortage. However, solar evaporators typically rely on internal pores for water transport that impedes vapor escape. In this work, exploiting a two-phase structure and directional arrangement of bamboo, a bamboo fiber aggregation (BFA)-based broom-like solar evaporator with open fibrous gaps for water transport and vapor diffusion is developed. The polypyrrole-coated BFA (PPy-BFA) evaporator exhibits a water evaporation rate of 3.3 kg m −2 h −1 with an efficiency of 146.7% under 1 sun. This value is 2.6 times higher than that of PPy-coated natural bamboo and superior to most of the previously reported bamboo-based evaporators. These low-tortuosity fiber gaps enable rapid water transport while providing extensive air–liquid interfaces that effectively promote vapor diffusion and harness heat from the environment. Open-channel configuration has a lower surface temperature and more uniform vapor distribution than that of the internal-channel one, preventing the formation of high-humidity zones. Moreover, PPy-BFA also demonstrates excellent salt tolerance performance, maintaining a stable evaporation rate of 2.3 kg m −2 h −1 for 20% NaCl solution. This work offers important insights into the configuration design of solar evaporators and provides a low-cost choice for off-grid desalination.
✓ 已验证
产品关联
DOI
高影响因子
RARE METALS
·
2026
·
IF 11
Chenqiang Duan,Li Guan,Shijie Han,Yujie Zhu,Ziyang Huang,Keqiang Cheng,Yuanyuan Zhang,Xinglai Yuan,Biao Zhao,Rui Zhang
en This link goes to a English section zh This link goes to a Chinese section The growing concern over human health issues, driven by increasingly severe electromagnetic pollution from 5G communication, has made the urgent development of high-performance electromagnetic wave (EMW) absorbing materials. Although carbide-based materials are promising because of their conductive and polarization losses, existing single-component materials fall short of future requirements. We report a lattice distortion engineering strategy to design and synthesize a stable high-entropy carbide (Ta 0.2 Nb 0.2 Ti 0.2 Zr 0.2 Cr 0.2 )C. The lowest reflection loss reaches −62.40 dB, and it exhibits an effective absorption bandwidth (EAB) of 6.39 GHz, a fourfold enhancement compared to that of the single component material TaC. Results indicate that severe lattice distortion in the high-entropy composition induces the formation of high-density defects, and the presence of metal vacancies significantly enhances the high-entropy carbides conduction loss and dipole polarization. Concurrently, the abundant grain boundaries and hyper-dense distorted lattices provide significant interfacial polarization and relaxation polarization, effectively broadening the electromagnetic absorption bandwidth. Electron holography analysis confirmed that a substantial accumulation of positive and negative charges at nano-interfaces leads to an anomalous dielectric polarization loss. This study contributes an effective pathway for designing potent single-phase electromagnetic wave absorption materials and provides a paradigm for improving other properties of high-entropy carbides via the lattice distortion strategy. 摘要 en This link goes to a English section zh This link goes to a Chinese section 随着5G通信引发的电磁污染日益严重,人们对健康问题的关注日益增加,这促使高性能电磁波吸收材料的开发成为当务之急。虽然碳化物基材料因其导电性和极化损耗而具有潜力,但现有的单组分材料仍无法满足未来需求。我们提出了一种晶格畸变工程策略,用于设计并合成稳定的高熵碳化物(Ta 0.2 Nb 0.2 Ti 0.2 Zr 0.2 Cr 0.2 )C。其有效吸收带宽(EAB)达到6.39 GHz,较单组分材料TaC提升了四倍,并且反射损耗最低可达−62.40 dB。结果表明,高熵成分中的严重晶格畸变会诱导形成高密度缺陷,而金属空位的存在显著增强了高熵碳化物的导电损耗和偶极极化。同时,丰富的晶界和超致密畸变晶格提供了显著的界面极化和弛豫极化效应,有效拓宽了电磁吸收带宽。电子全息分析证实,纳米界面处正负电荷的大量聚集导致了异常的介电极化损耗。本研究为设计高效单相电磁波吸收材料提供了有效途径,并通过晶格畸变策略为提升高熵碳化物的其它性能提供了范式。
✓ 已验证
产品关联
DOI
高影响因子
JOURNAL OF APPLIED POLYMER SCIENCE
·
2026
·
IF 2.8
Shuqing Sun,Jianyu Gong,Rui Yuan,Li Gao,Bingxin Liu,Shiai Xu
Phthalate plasticizers are the most commonly used plasticizers for soft PVC, but their composite materials are highly prone to cracking in low-temperature environments, leading to significant economic losses. Enhancing the cold resistance of plasticizers may be key to solving this issue. Therefore, this study employs dioctyl phthalate (DOP) as the primary plasticizer and synergistically blends it with the synthesized cold-resistant plasticizers dioctyl adipate (DOA) and dioctyl sebacate (DOS). Experimental results demonstrate that the addition of DOA and DOS significantly improves the low-temperature toughness of PVC/DOP composite films. For instance, at −20°C, the elongation at break of PVC/DOP/DOA and PVC/DOP/DOS increased by 48% and 42%, respectively, compared to PVC/DOP. Similarly, the glass transition temperatures of the compounding film are also higher than those of PVC/DOP. Migration resistance tests indicate that blending DOP with DOA or DOS can slow the migration rate of both DOS and DOA within the resin. Additionally, low-temperature in situ Raman spectroscopy is employed to investigate structural changes in DOP/PVC films under extreme cold conditions. DOP gradually precipitates from the matrix phase and forms crystalline structures on the film surface under low temperatures. This leads to PVC plasticization failure, resulting in brittle fracture.
✓ 已验证
产品关联
DOI
高影响因子
JOURNAL OF APPLIED POLYMER SCIENCE
·
2026
·
IF 3.1
Jun-Feng Su,Xiao-Nan Su,Xin-Yu Wang,Qin-Yu Xing,Peng Yang,Zhi-Yong Tan
This study introduces high-performance self-lubricating epoxy composites incorporating bioinspired silica microcapsules. Fabricated via optimized oil-in-water emulsion, the microcapsules (8–22 μm diameter, 0.5–0.6 μm shell thickness) demonstrate excellent thermal stability (200°C for 1 h) and high polyalphaolefin (PAO) encapsulation efficiency. At 5.0 wt% loading, the composite achieves outstanding tribological performance with an 89% reduction in both friction coefficient (from 0.56 to 0.08) and wear rate (from 120 to 13 × 10 −6 mm 3 /Nm) under 5 N load, while retaining 85% of compressive strength. Microstructural analysis confirms uniform microcapsule dispersion and strong interfacial adhesion with the epoxy matrix. The composite exhibits a unique stress-responsive lubrication mechanism where mechanical triggers cause microcapsule rupture, releasing PAO to form continuous lubricating films combined with silica fragments. This dynamic process is quantitatively described by a conceptual kinetic framework model that accounts for stress-dependent rupture and lubricant entrainment. The excellent balance of tribological properties and mechanical integrity demonstrated under laboratory conditions makes these composites promising candidates for further investigation toward demanding applications.
✓ 已验证
产品关联
DOI
高影响因子
Small
·
2026
·
IF 12.1
Shuaibo Zhang,Donglei Fu,Junjie Deng,Ruyi Wei,Xinghai Liu
The development of sustainable flexible electronics is hindered by a lack of sensing materials that synergize eco-friendliness, robust mechanical properties, and reliable electromechanical responsiveness. While starch-based hydrogels present a promising sustainable alternative, their widespread application is limited by inherent brittleness and significant signal hysteresis. Here, a molecular engineering strategy is proposed to address these limitations. Porous starch is first obtained through a gradual solvent exchange process to enhance chain accessibility. Protocatechuic acid (PCA) is then covalently grafted onto the starch backbone via EDC/NHS-mediated esterification, introducing dynamic hydrogen-bonding and π − π interaction motifs. By optimizing the ratio between PCA-modified starch and polyacrylamide (PAM), a bioinspired hydrogel with exceptional toughness and rapid electromechanical response is achieved. The resultant hydrogel exhibited pronounced strain-dependent resistance behavior, enabling its integration into a wireless wearable human-machine interface. To ensure robust decoding against motion-induced noise, a finite state machine (FSM)-based algorithm is employed for adaptive signal segmentation, achieving a character-level accuracy of 99.2% in trials with healthy subjects ( n = 10). This work not only introduces a high-performance, sustainable hydrogel platform but also demonstrates a practical route toward inclusive and language-independent human-machine communication.
✓ 已验证
产品关联
DOI
PubMed
高影响因子
Small
·
2026
·
IF 11.8
Hui Deng,Jinwei Hong,Ruijin Zheng,Yu Zhou,Weihuang Wang,Haifang Zhou,Peijie Lin,Jinling Yu,Yunfeng Lai,Shuying Cheng
Antimony sulfide (Sb 2 S 3 ) photodetectors (PDs) show great prospects in applications of optical communication and imaging. The detector performance is significantly influenced by reflection losses at the incident surface, particularly under weak-light conditions. Herein, we propose self-powered Sb 2 S 3 thin film PDs (glass/ITO/patterned ITO/TiO 2 /Sb 2 S 3 /Au) with light-trapped ITO patterns to enhance absorbance and performance. Periodic cuboid-patterned ITO patterns with the sizes of 50 × 50 µm 2 and depth of 250 nm are fabricated using photolithography and magnetron sputtering, which achieves about a 21% absorbance enhancement of visible light and 16% photocurrent increase of Sb 2 S 3 PDs. Meanwhile, the patterned ITO slightly expands the heterojunction contact area, which enhances the built-in electric field and the carrier extraction efficiency. Under the 530-nm light illumination of 5 µW/cm 2 , the device achieves a responsivity of 4.5 A/W and a specific detectivity of 1.4 × 10 13 Jones, demonstrating its weak-light detection ability. The Sb 2 S 3 PDs array, featuring fast response and a wide 3 dB bandwidth, has demonstrated image sensing capabilities by clearly resolving variations in bright and dark fields, showcasing application potentials.
✓ 已验证
产品关联
DOI
PubMed
高影响因子
JOURNAL OF APPLIED POLYMER SCIENCE
·
2026
·
IF 2.8
Yuning Yang,Qiao Yan,Yiming Zhou
Chromium (Cr) ions, as a critical pollutant in industrial wastewater, posed a persistent challenge for research aiming to realize their efficient removal alongside detoxification. Here, we presented a novel cellulose-based nanoadsorbent, PDA@CNCs/FeS, obtained via dopamine (DA) self-polymerization onto cellulose nanocrystals (CNCs) and subsequent FeS nanoparticle immobilization. Experimental results demonstrated that the adsorbent achieved a high removal capacity of 837.9 mg/g for Cr(VI) and exhibited efficient removal under mildly acidic conditions (pH 5.0), which outperformed the majority of cellulose-based adsorbents. The adsorption followed the Langmuir isotherm model and fitted well with the Pseudo-second-order kinetic. FTIR and XPS analyses confirmed the adsorption mechanism, which revealed that electrostatic attraction was involved in Cr(VI) removal, while the synergistic effect between reductive PDA and FeS on the nanoadsorbents facilitated the detoxification of toxic Cr(VI) to less harmful Cr(III). Nearly 70% of the adsorbed Cr(VI) was reduced to Cr(III), with a final ratio of 31.4%:68.6% for Cr(VI):Cr(III). Furthermore, PDA@CNCs/FeS also demonstrated excellent reusability, with over 80% of its Cr(VI) removal efficiency remaining after four adsorption–desorption cycles; these findings implied that PDA@CNCs/FeS held great promise as an adsorbent for Cr(VI) remediation in water treatment.
✓ 已验证
产品关联
DOI
高影响因子
RARE METALS
·
2026
·
IF 11
Rui Huo,Maoliang Tan,Hao Song,Liheng Wang,Tao Li,Feng Zhou,Zhi Chang,Paul K. Chu
en This link goes to a English section zh This link goes to a Chinese section Two-dimensional (2D) nonlayered niobium nitrides have attracted considerable interest for electrochemical energy storage. However, the synthesis of these materials is hampered by their nonlayered crystal structures, which are characterized by strong three-dimensional chemical bonding. Herein, we demonstrate the direct synthesis of nonlayered 2D NbN 0.8 /Nb 5 N 6 heterojunction nanosheets from commercial bulk Nb 2 O 5 through a scalable molten-salt-assisted route. The in situ formed molten KNbO 3 intermediate, confined within the K 2 CO 3 /KCl flux, guides the 2D growth of niobium nitride under NH 3 , yielding nanosheets with 4.8 nm thickness and lateral sizes of 3–5 μm. The as-synthesized 2D NbN 0.8 /Nb 5 N 6 nanosheets deliver a large capacitance of 918.2 F cm −3 (324.1 F g −1 ) at 1 A cm −3 , superior rate performance of 649.8 F cm −3 (229.4 F g −1 ) at 20 A cm −3 , and exceptional long-term cycling stability with 95.4% retention over 10,000 cycles, surpassing most reported niobium-based nitrides. Furthermore, the solid-state symmetric supercapacitor assembled with the two electrodes of 2D NbN 0.8 /Nb 5 N 6 nanosheets delivers a high volumetric energy density of 13 mWh cm −3 . This work reports a novel high-performance 2D niobium nitride electrode material and offers a generalizable synthesis strategy for 2D nonlayered transition metal nitrides. 摘要 en This link goes to a English section zh This link goes to a Chinese section 二维非层状氮化铌材料在电化学储能领域引起了广泛关注。然而,由于该类材料具有强三维化学键合的非层状晶体结构,其合成一直面临挑战。本研究展示了一种可规模化生产的熔盐辅助法,能够直接以商业块体Nb 2 O 5 为原料合成非层状二维NbN 0.8 /Nb 5 N 6 异质结纳米片。在NH 3 气氛下,原位生成并被限制在K 2 CO 3 /KCl熔盐介质中的KNbO 3 中间体,有效引导了材料的二维生长,最终获得了厚度为4.8 nm、横向尺寸为3–5 μm的纳米片。所合成的二维NbN 0.8 /Nb 5 N 6 纳米片在1 A cm −3 电流密度下具有918.2 F cm −3 (324.1 F g −1 )的高比电容,在20 A cm −3 下仍保持649.8 F cm −3 (229.4 F g −1 )的优异倍率性能,以及卓越的长循环稳定性(10,000次循环后容量保持率高达95.4%),其性能优于大多数已报道的铌基氮化物。此外,利用该二维NbN 0.8 /Nb 5 N 6 纳米片组装的固态对称超级电容器,可提供13 mWh cm −3 的高体积能量密度。本工作不仅报道了一种高性能的二维氮化铌电极材料,也为二维非层状过渡金属氮化物的合成提供了一种普适性策略。
✓ 已验证
产品关联
DOI
高影响因子
Solar RRL
·
2026
·Vol. 10
·期 2
·e202500917
·
IF 4.7
Lu Peng,Qiang Li,Siting Shao,Meng Zhang,Hongpeng Jia
The escalating CO 2 concentration and energy demand necessitate efficient CO 2 conversion strategies. Photothermal catalytic CO 2 methanation is a promising strategy, yet its efficiency is hindered by the inherent stability of CO 2 and the rapid recombination of photogenerated charge carriers. Among non-noble metal catalysts, Ni-based catalyst is a promising candidate for CO 2 methanation, with sintering and agglomeration remaining to be addressed. Herein, NiMn/TiO 2 bimetallic catalysts with varying Ni/Mn ratios were synthesized to overcome these issues. Characterization results demonstrate that Mn incorporation enhances CO 2 adsorption capacity by increasing oxygen vacancies and significantly improves the separation efficiency of photogenerated carriers. Furthermore, Mn doping optimizes the electronic structure of the catalyst, narrowing its bandgap for improved light absorption. But the catalytic performance is highly dependent on the Ni/Mn ratio. The synergistic effect of Ni and Mn can be maximized when the Ni/Mn ratio is 1:1, which is specifically manifested as the best catalytic activity. Excessive Mn loading covers active Ni sites and impedes electron transfer, thereby degrading activity. Therefore, this work highlights the importance of Mn as a promoter in designing efficient non-noble metal catalysts for photothermal CO 2 conversion.
✓ 已验证
产品关联
DOI
高影响因子
JOURNAL OF APPLIED POLYMER SCIENCE
·
2026
·
IF 3.1
Shijie Tang,Sen Wen,Haiyang Feng,Kesan Yang,Haichuan Li,Shenwen Fang
The highly efficient air flotation hydrocyclone separation technology has been gradually promoted and applied. However, the performance of flocculant reported in the literature needs improvement. In this study, a novel flocculant was synthesized using poly[N-(3-dimethylaminopropyl)methacry] (PDPM) and polyether monoamine (PMA) as the main raw materials. The synthesis conditions of the flocculant were optimized based on the oil removal rate. It was found that when PMA M-2095 was used, the resulting product, Cl-0.4-P-0.2-2095, exhibited the best flotation-flocculation oil removal performance. At a dosage of 20 mg/L and a treatment time of 7 min, the oil removal rate of Cl-0.4-P-0.2-2095 reached 90.63%, which was 31.7% higher than that of the reported flocculant. Mechanistic investigations, including measurements of surface tension, interfacial tension, zeta potential, and interfacial elastic modulus, as well as oil-coated bubble experiments, revealed that Cl-0.4-P-0.2-2095 adsorbs onto the surfaces of bubbles and oil droplets. This adsorption enhances the collision and adhesion efficiency between bubbles and oil droplets, thereby improving the flotation-flocculation oil removal performance. This study provides a novel treatment agent for the efficient treatment of produced water from offshore oilfields.
✓ 已验证
DOI
高影响因子
RARE METALS
·
2026
·
IF 11
Fan Xue,Liang Chen,Xindong Zhu,Jianrong Zeng,He Zhu,Si Lan
en This link goes to a English section zh This link goes to a Chinese section Precise control of chemical ordering in bimetallic nanocatalysts offers a route to decouple activity and selectivity in acetylene hydrogenation, but direct atomic-scale evidence linking surface order to catalytic performance is scarce. Here, we tune Pd-Cu nanoalloys from chemically disordered to highly ordered states by composition control and targeted H 2 thermal treatment. Under near-industrial conditions, all catalysts reach full acetylene conversion between 100°C and 120°C, whereas the ethylene selectivity enhances with the chemical ordering increasing. By combining synchrotron X-ray absorption fine structure (XAFS) with X-ray total scattering and reverse Monte Carlo (RMC) simulation, three-dimensional atomic models are reconstructed to quantitatively map surface coordination. Compared with the chemically disordered Pd-Cu nanocatalyst, the highly ordered PdCu shows an increase in average surface Pd-Cu coordination and an expansion of mean surface Pd-Pd separations. These structural features weaken ethylene binding and suppress re-adsorption, rationalizing the enhanced selectivity. Our study provides direct atomic-scale evidence connecting chemical order to catalytic selectivity and opens the way for guiding the precise design of bimetal nanocatalysts. 摘要 en This link goes to a English section zh This link goes to a Chinese section 精准调控双金属纳米催化剂的化学有序,可为乙炔加氢反应中活性与选择性的解耦提供有效路径。然而将表面有序度与催化性能直接关联的原子尺度证据仍较为缺乏。本研究通过成分调控与氢气热处理,成功实现了Pd-Cu纳米合金从化学无序态到高度有序态的转变。在近工业条件下,所有催化剂均在100–120°C区间内实现乙炔完全转化,而乙烯选择性随化学有序度的提升显著增强。结合同步辐射X射线吸收精细结构谱、X射线全散射及反向蒙特卡洛(RMC)模拟,我们重构了纳米合金的三维原子结构模型,实现了表面配位环境的定量解析。与化学无序的Pd-Cu纳米催化剂相比,高度有序的PdCu合金表现出更高的表面Pd–Cu配位数和更长的平均Pd–Pd键距。这些结构特征有助于弱化乙烯吸附并提高其选择性。本研究为化学有序与乙烯选择性之间的关联提供了直接的原子尺度证据,为双金属纳米催化剂的精准设计开辟了新途径。
✓ 已验证
产品关联
DOI
高影响因子
Small
·
2026
·
IF 12.1
Run Huang,Yonghui Wu,Xiaoling Liu,Ling Zou,Jinbao Li,Jian He,Lu Yang,Xiaochao Yang
The excessive generation of reactive oxygen species (ROS) and its synergistic interplay with inflammation and apoptosis play a critical role in the progression of drug-induced liver injury (DILI). Ceria nanoparticles are potential DILI therapy candidates due to their self-renewable ROS scavenging activity. However, the clinical translation of ceria nanoparticles for DILI therapy is challenged by enhanced ROS scavenging activity and prolonged hepatic retention. Herein, the sulfur-fumigation approach is used to modulate the ROS scavenging activity of ceria nanoparticles through the surface microstructure reconfiguration mechanism. The sulfur-fumigation induces nanoparticle contraction and crystalline fusion. Crucially, sulfur-fumigation decreases (111) plane exposure but increases (200) and (220) plane exposure. These changes cause the generation of abundant oxygen vacancies, which significantly enhances the ROS scavenging activity of ceria nanoparticles, even when the surface area is decreased. Together with an appropriate hydrodynamic diameter (135.9 nm) for liver targeting, the sulfur-fumigated ceria nanoparticles can easily accumulate in the liver and alleviate ROS, inflammation, and apoptosis in DILI mice. Compared to the clinical standard N-acetylcysteine (NAC), the sulfur-fumigated ceria nanoparticles show better therapeutic efficacy across most of the detected parameters. These findings suggest that sulfur-fumigation is a potent surface reconfiguration strategy to engineer highly active ceria nanoparticles for DILI therapy.
✓ 已验证
产品关联
DOI
PubMed
高影响因子