JOURNAL OF CLUSTER SCIENCE
·
2017
·Vol. 28
·期 6
·3059-3066
·
IF 1.471
Liang Hua,Yang Zhen-Yuan,Yan Min-Hao,Xie Su-Yuan
The fullerenes that violate isolated pentagon rule (IPR) have unusual electronic properties resulting from their fused-pentagon structures. Numerous non-IPR fullerenes have now been captured by chlorination, affording opportunity to go insight into the properties involved in non-IPR fullerenes in the forms of chlorofullerenes (CFs). Here cyclic voltammetry (CV) is employed to probe the electrochemical properties of non-IPR #1809 C 60 Cl 8 in comparison with those of #271 C 50 Cl 10 . Differing from IPR-satisfying CFs such as C 60 Cl 8 and C 60 Cl 10 (referring to I
h -symmetric C 60 ), the two non-IPR CFs exhibit divergent electroactive polymerization characters. In addition, the electrocatalytic effect of ferrocene that is otherwise employed as internal reference has been shown in the CV process of CFs.
研究领域:
材料化学
·
物理化学
·
纳米材料
·
电化学
·
富勒烯化学
✓ 已验证
DOI
高影响因子
Sustainable Energy & Fuels
·
2018
·Vol. 2
·期 10
·2154-2159
·
IF 0
Xing Guo,Bingjuan Zhang,Zhenhua Lin,Jie Su,Zhou Yang,Chunfu Zhang,Jingjing Chang,Shengzhong (Frank) Liu,Yue Hao
The electron/hole transport layer plays a very important role in the planar structure of perovskite solar cells. Conjugated polymers have received considerable attention for use in perovskite solar cells as hole/electron transport layers and passivation layers. Although the devices based on conjugated polymer hole transport layers have achieved much progress, their performance is still inferior to that of devices based on the conventional spiro-OMeTAD hole transport layer. Here, we investigated the solvent vapor annealing (SVA) effect on conjugated polymers as well as the corresponding perovskite solar cell devices. It was found that SVA treatment could enhance the hole charge carrier mobility and thin film crystallinity. Meanwhile, the charge transfer efficiency was enhanced, and charge recombination was reduced. Hence, the conjugated polymer based device exhibited comparable or even better performance compared with the conventional spiro-OMeTAD based device. Moreover, the device stability was also improved.
研究领域:
材料科学
·
光伏技术
·
纳米科技
·
表面与界面化学
·
凝聚态物理
·
能源材料
·
器件物理
✓ 已验证
DOI
Physica Status Solidi-Rapid Research Letters
·
2023
·Vol. 18
·期 7
·2300102
·
IF 2.8
Wenlong Chu,Ruifeng Xin,Luwei Zou,Xiulian Fan,Xilong Zhou,Cheng Li,Yu Zhou
2D nonlayered materials have attracted more and more attention due to their novel properties and special surface structures. However, due to isotropic chemical bonds within the crystal, the synthesis of ultrathin 2D nonlayered materials is an urgent challenge. Herein, α -Fe 2 O 3 2D nanosheets as thin as ≈8.2 nm on different substrates using self-designed ultralow concentration precursors combined with Gibbs free energy and Se catalysts design are successfully synthesized. The thickness-dependent growth mechanism is systematically studied, demonstrating the thermodynamic and kinetic controlling factors. The as-grown α -Fe 2 O 3 nanosheets are demonstrated with single-crystal structures without any other elements doping. The α -Fe 2 O 3 nanosheets photodetectors show the reasonable response performance with the positive photoconductive mechanism. This improved chemical vapor deposition method provides a promising idea for the synthesis of ultrathin 2D nonlayered materials.
研究领域:
材料科学
·
纳米科技
·
表面科学
·
凝聚态物理
·
光电子学
✓ 已验证
DOI
高影响因子
Asia-Pacific Journal of Chemical Engineering
·
2022
·Vol. 17
·期 5
·e2790
·
IF 1.777
Bingyi Zhou,Tao Ge,Xiaoman Luo,Zhaohui Wang,Yueyue Qiao,Chuanchuan Cai,Jingyao Xu
Under the two frequency microwave conditions of 915 and 2450 MHz, orthogonal tests were designed to investigate the effects of organic acid reagent, microwave irradiation time, and mixing time of additives and coal samples on the desulfurization effect of coal. Results show that the effect of irradiation time on the experimental desulfurization efficiency under frequency microwave conditions is large and is the main factor. The desulfurization effect under 915 MHz microwave condition is better than 2450 MHz microwave condition. Two sets of experimental optimal coal samples were used for characterization and analysis. Thermogravimetric analysis revealed that the combustion temperature range of the coal samples is shortened and the integrated combustion index is considerably higher after the microwave irradiation experiment. Fourier-transform infrared spectroscopy analysis showed that the overall chemical structure of the coal samples does not change significantly after the experimental treatment. X-ray photoelectron spectroscopy analysis showed that the intensity of organic sulfur in coal samples is weakened after microwave irradiation, the characteristic peaks of thiols and thioethers are reduced to a great extent, and an increase in the intensity of sulfoxide organic sulfur is observed. On the basis of the results of experimental analysis and quantum chemical simulation calculations, the mechanism of organosulfur structure removal under the action of microwave is revealed.
研究领域:
能源化学
·
煤化学
·
环境工程
·
材料科学
·
物理化学
·
分析化学
·
清洁燃料技术
✓ 已验证
DOI
高影响因子
JOURNAL OF APPLIED POLYMER SCIENCE
·
2021
·Vol. 139
·期 1
·51418
·
IF 3.125
Lan Hao,Xulin Cui,Xiaoli Wu,Jingtao Wang,Yifan Li,Wenpeng Li,Xingzhong Cao,Haoqin Zhang
Efficient separation of aromatic-aliphatic hydrocarbon mixtures has long been an important topic in chemical industries. Organic nanofiltration (OSN) has been revealing great promise in separating solvent mixtures that has not been effectively resolved by the state-of-the-art technologies. Herein, novel OSN membranes are designed for the separation of toluene and n -heptane. Polyamide active layer with diaminonaphthalene as the aqueous phase monomer is prepared by interfacial polymerization for the first time. The addition of polydimethylsiloxane gutter layer, as well as the combination of spin coating technique and macroporous substrate, renders the membranes with loose and defect-free architectures. The as-designed membranes achieve a rather high selectivity of toluene over n -heptane (>4) together with ultra-high toluene permeance (>180 L m −2 h −1 bar −1 ). These membranes also present excellent stability in the long-term operation.
研究领域:
材料科学
·
膜分离技术
·
化学工程
·
纳米技术
·
高分子化学
·
工业催化
·
绿色化学
✓ 已验证
DOI
高影响因子
Sustainable Energy & Fuels
·
2020
·Vol. 4
·期 6
·2800-2807
·
IF 5.503
Haili Yu,Busheng Zhang,Ruijuan Qi,Nannan Qu,Chaoliang Zhao,Yan Lei,Xiaogang Yang,Zhi Zheng
Designing lead-free inorganic perovskite or perovskite-like structure materials and researching the corresponding photoinduced charge carrier dynamics are always promising due to both the environment and power conversion efficiency considerations. In this work, we intelligently employ a bilayer metal Bi/Cu thin film with different atomic ratios as the precursor to fabricate a CuBiI4 perovskite-like film in situ with a controlled Bi gradient at room temperature. This structure can significantly affect the photoinduced charge carrier dynamics of the resulting products. Next, a series of transient surface photovoltage (TSPV) measurements are carried out to investigate the photoinduced charge carrier dynamics of such CuBiI4 and CuBiI4:organic hybrid thin films. The results reveal that the gradually decreasing Bi content from ITO to CuBiI4 can facilitate the photoinduced charge carrier transportation. Finally, a champion PCE of 1.10% is obtained for an ITO/CuBiI4:polythieno[3,4-b]-thiophene-co-benzodithiophene (PTB7)/Au solar cell device. In particular, we find an exact negative correlation of the defined parameter L (the defined value for evaluating the photoinduced charge carrier dynamics in TSPV measurements) with the corresponding PCE of various devices for the first time, which may pave a new way for evaluating the potential photoelectric and photovoltaic performances of new materials without the assembly of solar cell devices.
研究领域:
材料科学
·
光伏技术
·
凝聚态物理
·
表面科学
·
能源化学
✓ 已验证
DOI
高影响因子
CEMENT & CONCRETE COMPOSITES
·
2022
·
IF 9.93
Xing Ming,Qing Liu,Miaomiao Wang,Yongqing Cai,Binmeng Chen,Zongjin Li
Chloride-induced corrosion in reinforced concrete is a primary durability issue that causes large economic loss every year. To improve the intrinsic chloride binding capacity and realize a favorable corrosion protection of cement-based materials are thus crucial to prolong the service life of concrete structures. Here, alumina nano particles (ANPs) were incorporated to improve the chloride binding capacity of cement pastes in chloride solutions and the anti-corrosion performance of mortars under accelerated corrosion process. The ANPs facilitated the formation of alumino-ferrite-mono (AFm)-type phases, thereby improved the content of chemically bound chlorides. Solution calcium (Ca) ions benefited the chloride captured by calcium-(alumino-)silicate-hydrates (C-(A-)S-H) in the assistance of ANPs, especially at high initial chloride concentrations , and further evoked a pH-related chloride binding response. Moreover, the enhanced corrosion resistance was finally realized by incorporating appropriate amount of ANPs because of the filling and chemical effects induced low permeability of mortars. In general, the ANPs possess dual functions in the aspects of chloride binding and corrosion inhibition . These findings are expected to advance the design of high-durable cement-based materials serviced in the marine environment.
研究领域:
建筑材料
·
土木工程材料
·
腐蚀科学
·
纳米材料应用
·
混凝土耐久性
✓ 已验证
DOI
高影响因子
Journal of Energy Chemistry
·
2022
·
IF 13.599
Rong Li,Jiale Ding,Xijiao Mu,Yifei Kang,Anran Wang,Weihui Bi,Yunhe Zhang,Jing Cao,Qingfeng Dong
The extreme instability of pure α-phase FAPbI 3 under high humidity conditions restricts the high-throughput fabrication in unmodified air environments, resulting in poor performance of α-phase FAPbI 3 perovskite devices obtained by scalable fabrication methods. Here we synthesized hyperbranched copper phthalocyanine (HCuPc) as a supramolecular additive with twisted phthalocyanine units to realize the molecular-level encapsulation at the grain boundaries through supramolecular interaction, which greatly broadened the processing window of FAPbI 3 under high humidity. At the same time, unlike traditional encapsulation layer that carrier can only be collected by tunneling effect, the twisted phthalocyanine ring of HCuPc in perovskite films is more conducive to hole extraction. Finally, a record efficiency was achieved in pure FAPbI 3 based inverted structured solar cell by blade-coating to the best of our knowledge, even under unmodified humid air conditions (relative humidity of 65%–85%). The best operational stability of 3D pure FAPbI 3 devices can also be achieved at the same time and unencapsulated HCuPc-FAPbI 3 device can even operate with negligible degradation for 100 h in the open air (RH 30%–40%).
研究领域:
材料科学
·
纳米科技
·
能源化学
·
光伏技术
·
表面与界面化学
✓ 已验证
DOI
高影响因子
Small
·
2024
·Vol. 20
·期 31
·2310912
·
IF 13
Xunzhi Miao,Jianhe Hong,Shuo Huang,Liye Ding,Fang Wang,Min Liu,Quanquan Zhang,Hongyun Jin
All-solid-state lithium batteries (ASSLBs) are highly promising as next-generation energy storage devices owing to their potential for great safety and high energy density. This work demonstrates that composite solid polymer electrolyte with vertically-aligned card-house structure can simultaneously improve the high rate and long-term cycling performance of ASSLBs. The vertical alignment of laponite nanosheets creates fast and uniform Li + ion transport channels at the nanosheets/polymer interphase, resulting in high ionic conductivity of 8.9 × 10 −4 S cm −1 and Li + transference number of 0.32 at 60 °C, as well as uniformly distributed solid electrolyte interphase. Such electrolyte is characterized by high mechanical strength, low flammability, excellent structural stability and stable ion transport channels. In addition, the ASSLB cell with the electrolyte and LiFePO 4 cathode delivers a high discharge specific capacity of 124.8 mAh g −1 , which accounts for 85.6% of its initial capacity after 500 cycles at 1C. The reasonable design through structural control strategy by interconnecting the vertically-aligned nanosheets open a way to fabricate high performance composite solid polymer electrolytes.
研究领域:
材料科学
·
电化学
·
能源存储
·
高分子科学
·
纳米材料
·
电池技术
✓ 已验证
DOI
高影响因子
JOURNAL OF COLLOID AND INTERFACE SCIENCE
·
2018
·
IF 5.091
Siyuan Dong,Yingqi Jia,Xiaozhi Xu,Jianeng Luo,Jingbin Han,Xiaoli Sun
Poly(ethylene terephthalate) (PET) generally suffers from low crystallization rate and long molding duration, which as a result limit its application as engineering plastics. To overcome these drawbacks, series of PET/layered double hydroxide (LDH) nanocomposites were prepared by a solution blending process. The effect of metal composition (MgAl and CaAl) and organo-modification (stearic acid intercalated) for LDH fillers on the crystallization behavior of the nanocomposites was investigated. It was revealed that, compared with PET/CaAl-LDH, the PET/MgAl-LDH nanocomposite exhibits a higher crystallization temperature and faster crystallization rate, which is associated with the superior nucleation ability of MgAl-LDH. The nucleation mechanism of PET induced by LDHs was explored by means of Avrami equation and theory of Hoffman-Lauritzen, pointing out that the incorporation of LDHs reduce the free energy of nucleation and the fold surface free energy of PET. In order to improve the compatibility between LDH and PET, stearic acid (SA) intercalated MgAl-LDH was prepared and filled into PET matrix. The resultant PET/MgAl-LDH-SA shows a further enhanced crystallization temperature and accelerated crystallization rate, in comparison with PET/MgAl-LDH nanocomposites. In addition, the thermal stability, gas barrier and mechanical properties of PET/LDH composites were improved upon incorporation of LDH fillers.
研究领域:
高分子科学
·
材料化学
·
纳米复合材料
·
结晶动力学
·
聚合物物理
·
功能材料
·
工程塑料
✓ 已验证
DOI
高影响因子
JOURNAL DE MYCOLOGIE MEDICALE
·
2018
·
IF 1.606
K. Xu,J.L. Wang,M.P. Chu,C. Jia
Objective The aim of this study was to investigate the antibiofilm activity of coumarin against Candida albicans . Methods The efficacy of coumarin against biofilm formation and the mature biofilm of C. albicans was quantified by crystal violet (CV) staining and the 2,3-bis (2-methoxy-4-nitro-5-sulfophenyl)-5-[(phenylamino)carbonyl]-2H-tetrazolium hydroxide (XTT) reduction assay. The effect of coumarin on C. albicans adhesion was assessed on polystyrene plates and by using the cell surface hydrophobicity (CSH) assay. The morphological transition of C. albicans was conducted in two types of hyphae-inducing media at 37 °C. The expression of hypha/biofilm-related genes was evaluated using qRT-PCR analysis. A rescue experiment involving addition of exogenous cyclic adenosine monophosphate (cAMP) was performed to investigate the involvement of cAMP in the yeast-to-hyphae transition. A C. albicans -infected Caenorhabditis elegans model was used to test the anti-virulence efficacy of coumarin. Results Treatment with coumarin strongly affected the capacity of C. albicans to form biofilm and significantly impaired the preformed mature biofilm. The addition of coumarin notably inhibited C. albicans adhesion, CSH, and filamentation . The expression of some adhesion- and hypha-related genes, including HWP1 , HYR1 , ECE1 , and ALS3 , was remarkably down-regulated upon exposure to coumarin. Supplementation with cAMP partly rescued the coumarin-induced defects in hyphal development. Finally, coumarin prolonged survival in C. albicans -infected nematodes. Conclusion Coumarin inhibited C. albicans biofilm, which was associated with attenuated adhesion and hyphal growth.
研究领域:
微生物学
·
药理学
·
分子生物学
✓ 已验证
产品关联
DOI
PubMed
高影响因子
JOURNAL OF NANOSCIENCE AND NANOTECHNOLOGY
·
2019
·Vol. 19
·期 1
·57-65
·
IF 1.093
Liu Wolong,Zhang Jiupeng,Liu Qi,Pei Jianzhong,Zhu Cunzhen,Liu Peng
Micro-damages always occur and accumulate in asphalt pavement materials under the effects of temperature, vehicle loads and other factors during service. Accordingly, self-healing microcapsules could be added into asphalt binder and repair micro-damages to prevent damage extension in
time. In this study, the emulsified rejuvenator and melamine-urea-formaldehyde resin (MUF) were selected as the core and cyst wall materials, respectively, and in-situ polymerization method was applied to synthesize the novel microcapsules. The effects of emulsifier dosage and curing
time were revealed on the particle size, dispersion, surface morphology and coating properties, and the optimum process parameters were determined for microcapsules. Then, the micro morphology, molecular structure, and thermal stability were further investigated to determine the optimal preparation
of the microcapsules. Finally, the linear amplitude sweep (LAS) test was performed to evaluate the self-healing efficiency of the asphalt binder with different dosages of prepared microcapsule, and the optimal dosage of microcapsules was determined as 0.5%.
研究领域:
材料科学
·
土木工程
·
化学工程
✓ 已验证
产品关联
DOI
PubMed
高影响因子
危险品化学品经营许可证（带存储）