Journal of Inorganic and Organometallic Polymers and Materials
·
2024
·
IF 3.9
Li Mengke,Cao Panpan,Dong Wenwen,Zhao Jun,Li Dongsheng
Organic dyes pollution has caused significant threat to flora, fauna and humans because the toxic of dyes. In this work, with the help of acetic acid as a defect initiator, the hierarchical porous MIL-101(HP-MIL-101) has been synthesized and used for removing anionic dyes Eosin y (EY), Methyl orange (MO), Congo red (CR) and Acid fuchsin (AF) from water. Due to its positive surface charge, larger specific surface area, well-matched pore structure, and the charge, size, and diameter of dyes, HP-MIL-101 showed rapid adsorption and an excellent maximum adsorption capacity of 425 and 336 mg⋅g − 1 for CR and AF, respectively. A series of batch experiments were carried out to investigate the impact of various key factors, including adsorption duration, initial dye concentration, and temperature. In addition, the kinetics, isotherm, and thermodynamics about the adsorption properties were also discussed. In addition, HP-MIL-101 showed stable and high reusability for at least three cycles, with an efficiency of over 95% without significant structural changes. This study highlights the potential of hierarchical porous MOF for mitigating dye pollution and advancing sustainable water treatment methodologies.
✓ 已验证
产品关联
DOI
高影响因子
LANGMUIR
·
2025
·
IF 3.9
Dandan Liu,Hui Zhang,Jinfeng Mei,Xudong Zheng,Jian Rong,Zhongyu Li
A three-dimensional porous aerogel was synthesized by combining soft chitosan oligosaccharide to hard multi-walled carbon nanotubes (MWCNTs) under mild conditions. Owing to the support of MWCNTs, mesopores can be detected on the inner surfaces of the aerogel. The cross-linking by tetraethylenepentamine forms a macropore structure after freeze drying, using water as the template. The hydrogel can bear 30% recoverable compression with the aid of hydrogen bonds between the amide groups. The aerogel exhibits excellent adsorption capabilities for Cr(VI) in water. The adsorption capacity can reach 367.6 mg/g within 100 min. Notably, the aerogel demonstrated an extremely high efficiency in removal for trace Cr(VI). Soluble Cr(VI) of 1 mg/L can be completely removed by the aerogel at a dosage of 0.2 g/L. This work provides a new strategy to synthesize adsorbents with hierarchical pores that exhibit high porosity and a fast mass transfer rate.
✓ 已验证
产品关联
DOI
PubMed
高影响因子
RSC Advances
·
2024
·Vol. 14
·期 27
·19174-19184
·
IF 3.9
Peixin Hu,Hechao Lu,Qinting He,Fang Ren,Juan Wu,Wei Jiang
In this work, intelligent pH-sensitive sensors (Fe3O4/RhB@PAM) for Cr(VI) detection were successfully synthesized based on polyacrylamide (PAM) and Rhodamine B (RhB) co-modified Fe3O4 nanocomposites. The characterization results indicated that the sensors had many favorable properties, including suitable size, stable crystal structure and excellent magnetic response performance (47.59 emu g−1). In addition, the fluorescence changes during the detection process indicated that Fe3O4/RhB@PAM were “ON–OFF” intelligent sensors. When the Fe3O4/RhB@PAM sensors were placed in acidic Cr(VI) solution (pH 4), PAM acted as a pH-responsive “gatekeeper” releasing RhB, and the fluorescence intensity of released RhB was weakened by the complexation of Cr(VI). Furthermore, the fluorescence changes of the magnetic sensors were remarkably specific for Cr(VI) even in the presence of other competitive cations, and the limit of detection (LOD) for Cr(VI) was lower (0.347 μM) than the value recommended by the World Health Organization (0.96 μM). All the results presented in this study showed that the Fe3O4/RhB@PAM sensors had significant potential for Cr(VI) detection in acidic environmental samples.
✓ 已验证
产品关联
DOI
PubMed
高影响因子
Journal of Water Process Engineering
·
2024
·
IF 6.3
Junlong Cai,Bin Liu,Fazhi Xie,Xin Mao,Bing Zhang
Cr(VI) in chromium-containing industrial wastewater, which is highly toxic and difficult to degrade, brings great challenges to the treatment of industrial wastewater. However, conventional chromium removal methods suffer from low efficiency and secondary contamination. This study demonstrates that the micelle-enhanced nanofiltration (MENF) process is an effective strategy for the removal of Cr(VI). Micelles generated from two commonly used cationic surfactants (cetyltrimethylammonium bromide (CTAB) and cetyltrimethylammonium chloride (CTAC)) were capable of complexing with Cr(VI), resulting in the formation of aggregates with larger hydrodynamic diameters that were effectively retained by the membrane. The results showed that CTAC had a greater performance in removing Cr(VI) compared to CTAB, and the removal rate can reach 98.55 % at an initial concentration of 100 ppm. Meanwhile, the retention rate of surfactant under each condition was more than 96.23 %, which effectively reduced the generation of secondary pollution. Even in the presence of interfering anions, Cr(VI) still had a high affinity for cationic surfactant micelles. In addition, concentration polarization and micelles deposition acted as the main fouling potential during MENF process. This study provides a new insight into technological innovation and environmental protection in the field of wastewater treatment.
✓ 已验证
产品关联
DOI
高影响因子
JOURNAL OF HAZARDOUS MATERIALS
·
2018
·
IF 6.434
Jianhao Qiu,Xiong-Fei Zhang,Xingguang Zhang,Yi Feng,Yuxin Li,Lvye Yang,Haiqiang Lu,Jianfeng Yao
A novel and highly efficient photocatalyst of Cd 0.5 Zn 0.5 S@ZIF-8 nanocomposite has been developed by a facile self-assembly strategy. This is the first report on the application of Cd x Zn 1−x S and metal-organic framework (MOF) nanocomposite as photocatalysts for the reduction of Cr(VI). The resulting Cd 0.5 Zn 0.5 S@ZIF-8 exhibited higher photocatalytic activity than that of pristine Cd 0.5 Zn 0.5 S and ZIF-8. Particularly, the CZS@Z60 composite with 60 wt% of ZIF-8 exhibited a photocatalytic activity that is about 1.6 times as high as that of Cd 0.5 Zn 0.5 S. The dominant reason for the improved photocatalytic reduction potential is proved to be the newly-formed interfacial S Zn bonds that firmly connect Cd 0.5 Zn 0.5 S and ZIF-8 and substantially improve the separation efficiency of photo-excited electrons and holes. The newly-formed chemical bonds are confirmed by XPS analyses, and the prolonged lifetime of photo-excited electrons is evidenced by the electrochemical measurement of photocurrent, which shows that the photocurrent on Cd 0.5 Zn 0.5 S@ZIF-8 is much higher than that of Cd 0.5 Zn 0.5 S and ZIF-8. This study clearly demonstrates that the MOF-based composite nanomaterials hold great promises for applications in the field of environmental remediation and for design of novel photocatalytic materials.
✓ 已验证
产品关联
DOI
PubMed
高影响因子
ENVIRONMENTAL SCIENCE & TECHNOLOGY
·
2024
·
IF 10.8
Yacong Liu,Yue Lin,Weichao Wang,Ke Min,Weibo Ling,Wende Ma,Weican Zhang,Xingwang Hou,Linfeng Wei,Qian Liu,Guibin Jiang
With the increasing use of metal–organic frameworks (MOFs), they will inevitably enter the environment intentionally or unintentionally. However, the effects of MOFs on plant growth are poorly understood. Here, we investigated the effects of exposure of the rhizosphere to MOFs on plant growth. MIL-101(Cr) was selected as a research model due to its commercial availability and wide use. Soybean plants at the two-leaf stage were subjected to various durations (1–7 days) and concentrations (0–1000 mg/L) of exposure in hydroculture with a control group treated with ultrapure water. We found that MIL-101(Cr) had a positive effect on soybean growth at a lower dose (i.e., 200 mg/L); however, at higher doses (i.e., 500 and 1000 mg/L), it exhibited significant toxicity to plant growth, which is evidenced by leaf damage. To investigate the mechanism of this effect, we used Cr as an indicator to quantify, track, and image MIL-101(Cr) in the plant with laser ablation inductively coupled plasma mass spectrometry (LA-ICP-MS). Results indicated that MIL-101(Cr) primarily accumulated in the cortex of roots (up to 40 times higher than that in stems), with limited translocation to stems and negligible presence in leaves and cotyledons. In addition, metabolomic analysis of soybeans indicated that low-dose MIL-101(Cr) could increase the sucrose content of soybean roots to promote plant growth, while a high dose could induce lipid oxidation in roots. This study provides valuable insights into the ecological toxicology of MOFs and underscores the importance of assessing their environmental impact for sustainable agricultural practices.
✓ 已验证
产品关联
DOI
PubMed
高影响因子
International Journal of Applied Ceramic Technology
·
2024
·
IF 1.8
Shuaijun Yang,Mei Wang,Yetong Lv,Huilin Sheng,Yexia Qin
Oxidation resistance is crucial to the potential applications of high-entropy carbides (HECs) at elevated temperatures. Here, we realize the exploration of (Hf, Ta, Zr, Cr)C high-entropy carbides (HEC-TM, TM = Hf, Zr, Ta, and Cr) with good oxidation resistance by optimizing their compositions. To be specific, 21 kinds of HEC- x TM ( x = 0–25 mol%) samples are fabricated by a high-throughput ultrafast high-temperature sintering technique, followed by oxidation testing at 1673 K for 30 min. Among all the HEC samples, the as-fabricated HEC-0Zr samples are proved to possess the best oxidation resistance with an oxidation depth of only 53 µm. Further study on isothermal oxidation kinetics demonstrates that the as-fabricated HEC-0Zr samples follow a linear oxidation law. The good oxidation resistance of the as-fabricated HEC-0Zr samples is believed to result from the (Ta, Me) 2 O 5 phase with a low melting point, which can promote the densification of the oxide layer. This research opens up a new way for efficiently discovering new HECs for extreme applications.
✓ 已验证
产品关联
DOI
高影响因子
CHEMICAL ENGINEERING JOURNAL
·
2025
·
IF 13.2
Yulong Xiang,Xinbin Ji,Xiaoli Dong,Yu Wang,Nan Zheng,Chundong Liu,Menglin Wang,Chumin Yan
Photoreduction of toxic Cr(VI) in wastewater to less toxic Cr(III) presents an effective approach to address the environmental issues. Nevertheless, the photocatalytic performance of these photocatalysts is severely constrained by their narrow light absorption range and the rapid recombination of photo-generated electrons and holes. Herein, DUT-67/Fe 2 O 3 heterojunction photocatalysts were prepared by a simple mechanical grinding method. The formation of DUT-67/Fe 2 O 3 heterostructures not only increased the specific surface area and light absorption range, but also improved the separation of photogenerated charge carriers. Compared to the pristine DUT-67, DUT-67/Fe 2 O 3 exhibited significantly improved photocatalytic performance in the reduction of Cr(VI), achieving a reduction efficiency of up to 94 % within 40 min. Active species trapping experiments identified that electrons served as the primary species in the photocatalytic process. Coupled with electron spin resonance and density functional theory (DFT) calculations, a comprehensive mechanism for the photocatalytic reduction of Cr(VI) by DUT-67/Fe 2 O 3 Z-scheme heterojunction was proposed. This work offers new insights into the underlying mechanisms involving in the interfacial charge transfer and Cr(VI) photoreduction processes.
✓ 已验证
产品关联
DOI
高影响因子
APPLIED SURFACE SCIENCE
·
2025
·
IF 6.9
Yanan Wang,Chengzhuang Su,Songru Wang,Hao Tang,Hailuo Liu,Dong Wang,Aimin Wu,Hao Huang
The high integration of electronic devices severely hinders heat dissipation, impacting intelligent system performance. This study fabricated Cr-incorporated amorphous carbon films on aluminum alloy heat sinks using pulsed bias arc ion plating to enhance thermal performance. Film morphology and composition were analyzed via transmission electron microscopy (TEM), scanning electron microscopy (SEM), X-ray diffraction (XRD) and X-ray photoelectron spectroscopy (XPS). The Cr content was precisely regulated by adjusting the Cr target current, which was set at 0 A, 20 A, 40 A, and 60 A, respectively, and the effect of the sp 2 /sp 3 hybridization ratio on thermal dissipation was investigated. Results showed that increased Cr content led to the formation of B1-CrC in the amorphous carbon matrix. Optimal thermal performance occurred at a Cr target current of 20 A, at which the Cr content reached 6.21 at.%, yielding an infrared emissivity of 0.67 and a thermal conductivity of 160.95 W·m −1 ·K −1 . LED lamps coated with the Cr/C film exhibited a surface temperature 9.7 °C lower than that of uncoated lamps, thereby demonstrating excellent heat dissipation. The study underscores the synergistic effect of radial thermal conductivity and infrared emissivity in improving heat sink efficiency under non-forced convection.
✓ 已验证
产品关联
DOI
高影响因子
Nanoscale
·
2024
·Vol. 16
·期 7
·3650-3658
·
IF 5.8
Jun Tang,Jinzhao Huang,Sixuan Zhang,Zehui Liu,Jing Xiao
Although molybdenum disulfide (MoS2) has garnered significant interest as a potential catalyst for the oxygen evolution reaction (OER), its poor intrinsic activity and few marginal active spots restrict its electrocatalytic activity. Herein, we successfully constructed a catalyst via a simple hydrothermal method by forming a heterostructure of MoS2 with Cr-doped nickel–iron hydroxide (NiFe LDH) to synthesize a MoS2/NiFeCr LDH catalyst to significantly improve the OER catalytic performance. MoS2 plays a crucial function as an electron transport channel in the MoS2/NiFeCr LDH heterostructure, which increases the electron transport rate. Furthermore, a larger active surface area for NiFeCr LDH is provided by the ultrathin layered structure of MoS2, increasing the number of active sites and encouraging the OER. On the other hand, the introduction of Cr element increased the density of the catalytic center and provided additional Cr-OH active sites, which accelerated the oxygen decomposition reaction. These two factors act synergistically to improve the intrinsic structure of MoS2, increase the number of reactive sites, and dramatically enhance the OER catalytic performance. Excellent OER activity is demonstrated by the MoS2/NiFeCr LDH catalyst, which only needs an overpotential of 224 mV to obtain a current density of 10 mA cm−2 and a Tafel slope of 61 mV dec−1. The catalyst also demonstrated outstanding stability, with its activity practically holding steady after 48 h of testing. This work offers novel ideas for enhancing and designing MoS2-based OER catalysts, and it provides a crucial reference for research in the field of clean energy.
✓ 已验证
产品关联
DOI
PubMed
高影响因子
CHEMOSPHERE
·
2024
·
IF 8.1
Cheng Yu,Yassine Riahi,Qian Wang,Mengyang Feng,Abdelkader Mohamed,Ke Dai,Peng Cai,Qiaoyun Huang
Persistent free radicals (PFRs) in biochar are an important electron shuttle for mediating electron transfer, which has significant impact on the biogeochemical redox reactions. Although the influence of biochar on the extracellular electron transfer (EET) for redox cycle has been extensively studied, the molecular mechanism for promoting the EET with PFRs remains poorly understood. This study investigated the oxygen-centered PFRs-mediated Cr(VI) reduction by Shewanella oneidensis MR-1 (MR-1) and exhibited the molecular mechanism of electron transfer between flavin substances and PFRs. Results showed that the Cr(VI) bioreduction rate by MR-1 increased from 31% to 70% with the addition of biochar. Electrochemical results illustrated that biochar increased biocurrent generation in the Cr(VI) bioreduction process. 3D-EEM and LC/MS spectra indicated that MR-1 secreted the flavin mononucleotide (FMN) reductase that relied on the [H] to provide the electrons. Electron paramagnetic resonance spectra illustrated that PFRs in biochar accepted the electrons from FMN reductase and stored those bioelectrons. Because of the oxidation of FMN, the electron transfer from FMN reductase to PFRs would increase the intracellular reactive oxygen species, which further produced the extracellular ·O 2 − . The reduced PFRs released the bioelectrons, accelerating the Cr(VI) reduction by ·O 2 − . Together with the results of the mutant strains experiment, it was found that the EET by c -cytochrome and free radicals contributed to the Cr(VI) bioreduction by 7.1% and 92.9%, respectively. These findings revealed that the PFRs could participate in the EET process and promote the redox reactions, providing a new approach for enhancing the remediation of heavy metal pollution by microorganisms and suggesting the important role of PFRs in the electron transfer process.
✓ 已验证
产品关联
DOI
PubMed
高影响因子
Desalination and Water Treatment
·
2024
·
IF 1
Zhihui Zhao
The ease of agglomeration reduced the removal of pollutants by FeS particles. Hence, sludge biochar was employed as a support to produce FeS-loaded biochar composites (FeS@BC) using a solvothermal method, for removing Cr(VI) from wastewater. The performance and mechanism of Cr(VI) removal on FeS@BC were investigated through adsorption experiments and characterization techniques. The adsorption tests revealed that under optimal conditions of solution pH of 3 and dosage of 40 mg, FeS@BC achieved a removal efficiency of over 97 % for 50 mg/L Cr(VI). The presence of Cl - and NO - 3 did not affect Cr(VI) removal, whereas sulfate, phosphate, and carbonate inhibited the removal process. Low concentrations of humic acid (1–5 mg/L) held a negligible influence on removing, but elevated concentrations of humic acid inhibited Cr(VI) removal. The behavior of FeS@BC in removing Cr(VI) complied with to the pseudo-second-order and the Langmuir model. At 308.15 K, the largest removal capability of FeS@BC for Cr(VI) reached 185.874 mg/g. Thermodynamic studies confirmed that the Cr(VI) removing processes on FeS@BC were a spontaneous, entropy-driven, endothermic chemical adsorption. The primary mechanism for removing Cr(VI) on FeS@BC included reduction, electrostatic adsorption, complexation, and precipitation, with the reduction process playing a crucial role. This indicated that sludge biochar loaded with FeS was an ideal material for removing Cr(VI) from wastewater.
✓ 已验证
产品关联
DOI
高影响因子
危险品化学品经营许可证（带存储）