INTERNATIONAL JOURNAL OF HYDROGEN ENERGY
·
2016
·Vol. 41
·期 22
·9611-9618
·
IF 3.205
Jinhua Xiao,Wenying Zhang,Chunyan Xiong,Bo Chi,Jian Pu,Li Jian
Spinel oxides with the general formula of MnCu x Co 2−x O 4 (x = 0.1, 0.3, 0.5, 0.7 respectively) are used as coating materials on the metallic interconnect SUS 430 alloy to reduce the cathodic performance degradation by Cr poisoning and the interfacial resistance to improve the surface stability. The effect of Cu doping at the B position of spinel on the electrical conductivity and coefficient of temperature expansion (CTE) is investigated to determine the oxidation behavior and effectiveness as a protective layer. The result confirms that MnCu 0.5 Co 1.5 O 4 spinel shows highest electrical conductivity of 105.46 S cm −1 at 750 °C in air and an average CTE value of 12.27 × 10 −6 K −1 at temperature range of 20–960 °C. MnCu 0.5 Co 1.5 O 4 coating is stable enough after 2000 h cyclic oxidation at 750 °C. The growth of Cr 2 O 3 and formation of MnCr 2 O 4 in the scale layer are effectively suppressed by the presence of MnCu 0.5 Co 1.5 O 4 coating. The oxidation kinetics obeys the parabolic law with a rate constant as low as 2.76 × 10 −15 g 2 cm −4 ·s −1 and the ASR contributed by the oxide scale is 8.04 mΩ cm 2 at 750 °C. The research indicates that MnCu 0.5 Co 1.5 O 4 is a promising coating material for metallic interconnects of the intermediate temperature solid oxide fuel cells .
研究领域:
材料科学
·
能源材料
·
固体氧化物燃料电池
·
表面工程
·
电化学
·
高温腐蚀
·
功能涂层
✓ 已验证
DOI
高影响因子
PROGRESS IN ORGANIC COATINGS
·
2018
·
IF 2.955
Yuhua Dong,Siyi Li,Qiong Zhou
The self–healing capability of epoxy coatings modified with coaxial core–shell nanofibers loaded with the corrosion inhibitor 2–mercaptobenzothiazole (MBT) was investigated using electrochemical techniques. The polyvinyl alcohol/polyvinylidene fluoride core–shell nanofibers were prepared by coaxial electrospinning. Electrochemical impedance results showed that the MBT–loaded coaxial nanofibers improved the barrier properties and decreased the corrosion activity of the coatings. Results of the Scanning Kelvin Probe technique revealed that the MBT–loaded coaxial nanofibers healed corrosion over artificial defects exposed to NaCl electrolytes. These results indicate that adding MBT–loaded coaxial nanofibers to epoxy coatings is a promising strategy toward the development of self–healing epoxy coatings.
研究领域:
材料科学
·
高分子化学
·
腐蚀与防护
·
表面工程
·
功能材料
✓ 已验证
DOI
高影响因子
JOURNAL OF SOL-GEL SCIENCE AND TECHNOLOGY
·
2013
·Vol. 66
·期 1
·133-138
·
IF 1.66
Peng Shusen,Zhao Wenjie,Zeng Zhixiang,Li He,Xue Qunji,Wu Xuedong
In this report, hybrid silica sol–gel coating was prepared using Ce(NO 3 ) 3 (Sol-Ce) as catalyst. Structure, surface morphology and anticorrosion ability of Sol-Ce solution/coating were studied by infrared spectroscopy (IR), scanning electron microscopy, energy dispersive spectrometer (EDS), potentiodynamic scan (PDS) and electrochemical impedance spectroscopy (EIS). IR results showed that Ce(NO 3 ) 3 had a stronger influence on reactivity of alkoxysilane. EDS results revealed that the fraction of Fe in Sol-Ce coating was significantly lower than regular acid-catalyzed hybrid silica sol–gel coating (Sol-Ac) and Sol-Ac with Ce(NO 3 ) 3 -doped coating (Sol-Ac/Ce). The results of PDS and EIS demonstrated that Sol-Ce coating had better anticorrosion ability than Sol-Ac and Sol-Ac/Ce on carbon steel. The enhanced anticorrosion performance of the Sol-Ce coating might result from the following two reasons: (a) Ce(NO 3 ) 3 as a catalyst could alleviate the negative effects of low pH with using acid catalyst (dissolution of carbon steel) and (b) Ce(NO 3 ) 3 could impede corrosion of carbon steel as corrosion inhibitor.
研究领域:
材料科学
·
表面工程
·
腐蚀与防护
·
无机化学
·
电化学
✓ 已验证
DOI
高影响因子
PHYSICAL CHEMISTRY CHEMICAL PHYSICS
·
2017
·Vol. 19
·期 25
·16785-16794
·
IF 4.123
Wei Xia,Jun Zhao,Tao Wang,Li Song,Hao Gong,Hu Guo,Bing Gao,Xiaoli Fan,Jianping He
Polymer networks such as those of epoxy resin, as common protection materials, possess radiolytic oxidation degradation effects under gamma irradiation environment, which have a great accelerating effect on the ageing rate and severely limit their potential applications for metal protection in the nuclear industry. To overcome this, we report a simple scheme of anchoring crystalline ceria nanoparticles onto graphene sheets (CG) and incorporate it into the epoxy resin, followed by thermal polymerization to obtain CeO2/graphene-epoxy nanocomposite coating (CGNS). We had proven that graphene might act as “interwalls” in the epoxy matrix, which will result in space location-obstruct effect as well as absorb the radicals induced by γ-ray irradiation. Moreover, owing to the interconversion of cerium ions between their +3 and +4 states coupled with the formation of oxygen vacancy defects, electron spin resonance (ESR) detection shows that CeO2/graphene (CG) could act as a preferable radical scavenger and achieve better performance in trapping radicals than single graphene based composite. Electrochemical data strongly demonstrate that CeO2/graphene is capable of maintaining the anti-corrosion properties under gamma irradiation environment. Therefore, the designed hybrid CeO2/graphene-epoxy composite can be considered as potential candidates for protective coatings in nuclear industry.
研究领域:
材料科学
·
核工业防护
·
高分子化学
·
纳米复合材料
·
电化学防腐
✓ 已验证
DOI
高影响因子
PROGRESS IN ORGANIC COATINGS
·
2020
·
IF 4.469
Haihua Wang,Wenjing Zhang,Yongning Ma,Guiqiang Fei,Huan Wen,Liyu Sun,Yanming Shao,Yong-Mook Kang
The compatibility between polypyrrole (PPy) and waterborne epoxy coating (EP) remains the main challenge. Here, phosphorylated poly (vinyl alcohol) (PPVA) and p-toluene sulfonic acid sodium (p-TSA) were simultaneously utilized as dopants to modify PPy and prepare water dispersible PPVA/p-TSA/PPy (PPVAT/PPy) solution. Additionally, poly (vinyl alcohol) (PVA) and TSA were also adopted to prepare PVA/p-TSA/PPy (PVAT/PPy) for comparison. Denser film with granular morphology was observed for PPVAT/PPy nanocomposite film. Compared with PVAT/PPy-40 %, the tensile strength of PPVAT-8.0 %/PPy-40 % increased from 248.8–283.9 MPa. PPVAT/PPy displayed higher compatibility and interactions with EP compared to PPy-TSA and PVAT/PPy. Compared with EP, the impedance modulus of PVAT/PPy+EP and PPVAT/PPy+EP increased from 3.17×10 5 to 1.07×10 8 and 1.62×10 9 Ω·cm 2 ; corrosion current density I corr decreased from 1.49×10 −6 to 7.72×10 -8 and 4.01×10 -9 A·cm -2 ; corrosion potential E corr displayed a positive shift of 230 mV and 269 mV, respectively. The corrosion inhibition efficiency of PPVAT/PPy+EP reached 99.83 %, which is much higher than that of PVAT/PPy+EP (93.97 %). PPVAT/PPy+EP nanocomposite coating has been proved to have preferable long-term corrosion resistance based on electrochemical impedance spectra (EIS), polarization curves and salt water spray test. The simultaneous incorporation of phosphate anions, sulfate ions and PPy into EP was beneficial to fabricate high-performance anticorrosion coating.
研究领域:
材料科学
·
高分子化学
·
腐蚀防护
·
纳米复合材料
·
表面工程
✓ 已验证
DOI
高影响因子
Nano Energy
·
2020
·
IF 16.602
Long Li,Chun Fang,Wenfei Wei,Lei Zhang,Zhao Ye,Gang He,Yunhui Huang
The huge volume change of silicon anode during cycling results in unstable solid electrolyte interface (SEI), causing rapid performance degradation . Natural SEI layer has a heterogeneous structure, results in the inhomogeneous Li + diffusion. The repeated destruction and regeneration of SEI aggravate the inhomogeneity of Li + diffusion at the interface, leading to non-uniform alloy reaction in the Si bulk. In this work, the silicon surface is passivated by an ultrathin uniform chitosan layer with abundant lithiophilic groups. The capacity of chitosan-coated Si (Si@CS) could reach 1500 mAh g −1 at a current density of 1 A g −1 , and the capacity retention remains 91% after 400 cycles. It is demonstrated that the oxygen and nitrogen atoms in chitosan are coordinated with Li + , providing uniformly distributed Li + transfer sites, results in a homogeneous Li + flux in the surface layer. Interestingly, a nano-scale ordered atomic arrangement is observed in the delithiated Si@CS, which contributes to more stable and reversible lithiation/delithiation reaction of the Si@CS electrode. It is proposed that optimizing the reaction interface on the Si surface is able to alter the Li-ion diffusion kinetics and structure transition behavior of silicon, which can improve the structure reversibility and stability during cycling.
研究领域:
材料科学
·
电化学
·
纳米科技
·
能源存储
·
表面工程
·
锂离子电池
✓ 已验证
DOI
高影响因子
OPTICAL FIBER TECHNOLOGY
·
2013
·Vol. 20
·期 1
·28-31
·
IF 1.187
Jiao-Yang Li,Xu-Guang Huang,Wei Xu,Dong-Rui Xiao,Ze-Bing Zhong
A biocompatible fiber-optic pH sensor based on Fresnel reflection technique and a sensing coating is presented. Sodium alginate and polyethylenimine are alternatively deposited on the sensing fiber end to form the sensing coating via a layer-by-layer electrostatic self-assembly technique. An optical switch is added to the measurement system for the convenience of fast calibration. A linear, monotonic and fast response in a large pH range (from pH 5.87 to pH 10.55) is obtained with the resolution of 0.01 pH unit. The sensitivity of the pH sensor is 0.018 R.I.U/pH. It is not influenced by fluctuations of light source.
研究领域:
生物医学工程
·
传感技术
·
分子生物学
·
转化医学
·
生物材料
✓ 已验证
DOI
高影响因子
JOURNAL OF MEMBRANE SCIENCE
·
2013
·
IF 4.093
Qiang Xu,Yang Yang,Jie Yang,Xiaozu Wang,Zhaohui Wang,Yong Wang
Conformal and smooth TiO 2 thin layers were coated on the surface of porous PTFE membranes subjected to a plasma activation process by atomic layer deposition (ALD). In contrast, TiO 2 was deposited on the PTFE surface as globular particulates without plasma activation due to the inert chemical nature of PTFE surface. X-ray photoelectron spectrometry confirmed the formation of functional groups on the plasma-activated PTFE surface which served as active sites for the homogeneous adsorption and reaction of ALD precursors. Scanning and transmission electron microscopy revealed the uniformity of the deposited layer and the precise control of its thickness by changing ALD cycle numbers. The water contact angle measurement showed that the hydrophobic surface gradually turned to be near superhydrophilic with the increment of ALD numbers. Also, the membrane mean pore size was progressively reduced by simply altering the ALD numbers. At proper deposition conditions , the modified membranes gained an increase of pure water flux of more than 150% and simultaneously a doubled retention compared to the original unmodified membrane. This research provides an efficient approach devoid of any harsh treatments to modifying PTFE membranes for achieving specific functions, which also can be applied to other organic materials especially with chemical inert surface.
研究领域:
材料科学
·
膜科学与技术
·
表面工程
·
高分子化学
·
环境工程
·
纳米科技
✓ 已验证
DOI
高影响因子
Desalination and Water Treatment
·
2024
·
IF 1
Chao Yang,Jun Yang,Ge Song,Limin Zang,Qifan Liu,Jianhui Qiu,Xue Yang,Chun Wang
Oil/water separation has recently attracted a great deal of attention for research due to the frequent occurrence of an oil spill as well as the increase of industrial and household oily wastewater. Therefore, the purpose of this study is to demonstrate underwater superoleophobic crosslinked phosphorylated poly(vinyl alcohol) hydrogel coated stainless steel mesh (CL-PPVA@SSM), which was fabricated using a simple dip-coating method and aldol reaction on the mesh substrate. The as-prepared CL-PPVA@SSM is capable of separating oil from a variety of different oil/water mixtures with high separation efficiency up to 99.2%, excellent recyclability and fast water permeate flux of 467.7 L m –2 h –1 , which makes it suitable for the separation of oil-water mixtures from oil-water emulsions. Also, in the oil-water separation process, the CL-PPVA@SSM is capable to remove organic dye from the water. The CL-PPVA@SSM exhibits stability under various harsh conditions such as mechanical abrasion. Importantly, the CL-PPVA@SSM shows a massive potential to separate kitchen waste oil/water mixtures due to the underwater superoleophobic property as required for the recycling of kitchen waste oil. Therefore, this method has been met with a promising application prospect of practical application.
研究领域:
材料科学
·
环境工程
·
高分子化学
·
表面工程
·
化学工程
·
纳米技术
·
水处理技术
✓ 已验证
DOI
高影响因子
Journal of Materials Chemistry A
·
2023
·Vol. 11
·期 6
·2979-2984
·
IF 11.9
Wu Wei,Zhihong Wang,Liyun Yao,Hao Jiang,Chunzhong Li
Development of Ni-rich and Co-poor cathodes (Ni ≥ 80%, Co ≤ 5%) is indispensable for the next-generation lithium-ion batteries (LIBs) owing to the serious impact of scarce resources and fragile supply chain of cobalt, but they suffer from a more prominent lattice oxygen emission with serious Li/Ni intermixing as well as worsening crystal and interface structure. Herein, CeO2−x-coated LiNi0.9Co0.045Mn0.045Al0.01O2 has been demonstrated to stabilize lattice oxygen by the well-dispersed Al–O bonds and the reversible oxygen-storage protective layer. The in situ DEMS and ex situ spectral analyses verified the negligible O2 and CO2 emission, even charging to 4.4 V, and the formation of stable cathode–electrolyte interfacial membrane. The as-obtained cathode exhibited a reversible specific capacity as high as 223 mA h g−1 at 0.1C and 140 mA h g−1 even at 10C with 96.7% capacity retention at 1C after 100 cycles in a coin-type half-cell. About 90.1% capacity retention could still be obtained at 1C in a pouch-type full-cell after 300 cycles. This work provides a viable cathode for durable LIBs by stabilizing the lattice oxygen of Ni-rich and Co-poor cathodes.
研究领域:
电化学
·
材料科学
·
能源存储
·
锂离子电池
·
固态化学
·
表面科学
·
电极材料
✓ 已验证
DOI
高影响因子
Colloid and Interface Science Communications
·
2019
·
IF 1.87
Gaoqi Wang,Ding Weng,Chaolang Chen,Lei Chen,Jiadao Wang
The aim of the study was to explore the synergistic effects of nanostructure size and surface treatment of TiO 2 coatings on its wettability and bacteria adhesion. The coatings were fabricated by TiO 2 particles with a diameter ranging from 25 nm to 300 nm. The surface wettability of coatings was tuned by chemical treatment. The anti-adhesion property of as-prepared coatings was evaluated with Streptococcus mutans in two types of solutions: phosphate buffer solution (PBS) and PBS with 1 wt% sucrose. The results show that particle size and surface treatment have significant influences on the wettability (with contact angles of 0–160°) and bacterial adhesion. The coating prepared by chemically modified 25 nm particles has a superhydrophobic property, and could inhibit bacterial adhesion in aqueous solutions with sucrose or not. The study also provides a facile, universal and low-cost process to fabricate anti-adhesion coating, which is applicable for diverse of substrates.
研究领域:
生物材料学
·
纳米医学
·
表面科学
·
微生物学
·
口腔生物学
✓ 已验证
DOI
高影响因子
SOLAR ENERGY MATERIALS AND SOLAR CELLS
·
2020
·
IF 6.984
Shusheng Pan,Ziyue Rao,Yujie Wu,Zhiyu Liu,Jun Ge,Shan Zhang
In this study, a temperature self-regulating solar reactor based on VO 2 thermochromic coating is demonstrated. The temperature of solar reactor can be stabilized at 68.8 °C, which is corresponded to the critical point of metal-to-insulator transition of VO 2 . By employing the solar reactor, the orthorhombic phase CsPbI 3 microwires have been synthesized through solution phase reaction route. Strong emission peaks at 490 nm and 470 nm have been observed in CsPbI 3 microwires under ultraviolet and soft X-ray excitation, respectively. The high performance photodetector based on CsPbI 3 microwire show a detectivity of 1.09 × 10 14 Jones, responsivity of 4.72 A/W, rapid rise and decay time of 0.96 and 0.93 s at 325 nm. Our results demonstrate that the temperature self-regulating solar reactor can be applied for energy-saving solution phase reactor for synthesizing high quality inorganic materials.
研究领域:
材料科学
·
纳米光电子学
·
无机功能材料
·
能源材料
·
半导体器件
✓ 已验证
DOI
高影响因子
危险品化学品经营许可证（带存储）