Solar RRL
·
2021
·Vol. 6
·期 3
·2100554
·
IF 8.582
Daiyu Li,Pei Jiang,Wenhao Zhang,Jiankang Du,Chen Qiu,Jiale Liu,Yue Hu,Yaoguang Rong,Anyi Mei,Hongwei Han
Perovskite solar cells (PSCs) have achieved a certified power conversion efficiency (PCE) of 25.5% and show potential for low-cost photovoltaic applications. One key of pushing PSCs into industrialization is enlarging their areas. However, the PCE of larger-area PSCs is dramatically limited by the undesired increase in series resistance ( R S ), which leads to obvious loss of fill factor (FF). Herein, R S in fully printable mesoscopic PSCs is modulated with a carbon electrode by optimizing the device geometry, preparing busbars to collect currents from electrodes and improving the conductivity of the back electrode. A rectangular device shape and tin busbars on conductive substrate effectively reduce the R S . Meanwhile, an additional hot-pressed highly conductive low-temperature carbon layer on the back carbon electrode also reduces the R S . An enhanced PCE of 13.99% for 1 cm 2 PSCs by R S modulation is obtained, whereas the control device exhibits a PCE of 7.74%. The PCE increase is due to the improvement of FF from 0.372 to 0.638 with reduced R S from 27.13 to 9.66 Ω cm 2 .
研究领域:
材料科学
·
能源材料
·
光伏技术
·
纳米结构材料
·
电化学
·
器件物理
✓ 已验证
DOI
高影响因子
Sustainable Energy & Fuels
·
2021
·Vol. 5
·期 5
·1538-1547
·
IF 6.367
Ruyan Lei,Yanping Yang,Chenjuan Yu,Yinsi Xu,Yuanzhuo Li,Jun Li
In order to improve the electrochemical performance and efficiently prepare a solid polymer electrolyte (SPE) for the lithium-metal battery (LMB), a fumed SiO2 (FS) with surface Si–OH group was used to fabricate FS-modified poly(ethylene oxide) (PEO)–LiClO4-based SPE by a facile preparation process. The influences of the FS content on the morphological properties, thermal properties, lithium salt dissociation, mechanical properties, and electrochemical properties of SPE were systematically analyzed. Results indicate that FS with the hydrophilic property was widely distributed throughout the amorphous phase of SPE, thus the crystallinity of SPE was reduced to 25.83% when the FS mass loading was 6.85 wt%. In addition, a greater dissociation degree of lithium salt was achieved after the addition of FS, and a higher ion conductivity of 3.03 × 10−4 S cm−1 and Li-ion migration number of 0.396 were recorded at 60 °C. The all-solid-state Li/SPE/Li coin cell showed excellent stable cyclability (380 h) and the LiFePO4 (LFP)/SPE/Li coin cell demonstrated good discharge specific capacity and coulomb efficiency of 96 mA h g−1 and 100.2%, respectively, after 100 cycles of galvanostatic charge–discharge operation under 0.5C at 60 °C. Thus, based on collective results, it is expected that SPE presented in this work is a promising electrolyte for next-generation high-energy all-solid-state LMB with enhanced safety.
研究领域:
材料科学
·
电化学
·
能源存储
·
高分子化学
·
固态离子学
✓ 已验证
DOI
高影响因子
JOURNAL OF COLLOID AND INTERFACE SCIENCE
·
2018
·
IF 5.091
Nan Lu,Xi Zhang,Ruiqi Na,Wendi Ma,Chongyang Zhang,Yuchao Luo,Yongfeng Mu,Shuling Zhang,Guibin Wang
The synthesis of a nanocomposite gel polymer electrolytes (NGPEs) using Li + -functionalized SPEEK (SPEEK(Li)) nanofiber membrane as a matrix, cross-linked PVA as a gelled agent and LiClO 4 as an electrolytic salt for electric double layer capacitors (EDLCs) were reported in this work. Compared with conventional PVA based gel electrolyte, the “SO 3 − Li + ” functional groups and the pores structure of the SPEEK(Li) nanofiber membrane improves the ionic conductivity as well as mechanical stability , which made the prepared NGPEs exhibited a high ionic conductivity of 8.9 × 10 −3 S cm −1 at ambient temperature and a large voltage stability window range from 0 to 2.0 V. The fabricated symmetric EDLCs showed a specific capacitance of 146.96 F g −1 at a current density of 0.5 A g −1 , with a maximum energy density of 18.26 W h kg −1 . Meanwhile, the EDLCs showed outstanding cyclical stability of 98% specific capacitance retention after 3000 cycles GCD testing, all of these results indicated that the NGPEs should be appropriate to EDLCs and next-generation energy storage systems .
研究领域:
材料科学
·
电化学
·
能源存储
·
高分子化学
·
纳米技术
·
固体电解质
✓ 已验证
DOI
高影响因子
ELECTROCHIMICA ACTA
·
2020
·
IF 6.215
Shi Wang,Qingyuan Li,Minglei Bai,Jixin He,Chongyang Liu,Zengxi Li,Xiangfeng Liu,Wen-yong Lai,Liaoyun Zhang
Lithium-ion batteries (LIBs) using solid-state electrolytes (SSEs) can improve safety and energy density comparable with the liquid electrolytes (LE)-based counterparts. Especially, employing garnet-type SSEs to prepare solid-state LIBs are promising to achieve high-energy cells. However, the unbending and brittle issues of the inorganic SSE films are not suitable to fabricate flexible and stretchable energy storage devices. Here, We find that introducing specific polymer (30 wt%) into Li 6.75 La 3 Zr 1.75 Ta 0.25 O 12 (LLZTO) can strongly increase the strength of the composite polymer-in-inorganic electrolyte (CIE) film. Both in-situ and ex-situ characterizations demonstrate that CIE delivers an excellent ability to suppress the growth of Li dendrites due to the close packing of LLZTO and effective filled grain boundaries and voids inside the CIE film by the polymer. The CIE inherits impressive electrochemical performance from LLZTO. As a result, the assembled LiFePO 4 (LFP)/CIE/Li cell delivers better cell performance than LFP/LE-separator/Li cell at ambient temperature (AT). The assembled high-voltage cathode (Li 1.2 Mn 0.6 Ni 0.2 O 2 , 4.8 V)/CIE/Li cell also displays an excellent cell performance at AT. The present study offers new insights into exploring of flexible polymer-in-ceramic electrolytes for high-voltage LIBs with improved safety and energy density .
研究领域:
材料科学
·
电化学
·
能源存储
·
固态电池
·
纳米复合材料
·
界面工程
✓ 已验证
DOI
高影响因子
JOURNAL OF ALLOYS AND COMPOUNDS
·
2022
·
IF 6.371
Jianling Huang,ChengWei Liao,Hui Wang,YuJun Zhao,Liuzhang Ouyang,Jiangwen Liu,Min Zhu
Mg-based alloy anodes suffer from severe corrosion in conventional electrolytes (KOH solution) and this substantially obstructs the cycle life, which is a great challenge for using them in the Ni-MH battery. Herein, a high concentration tetramethylammonium hydroxide (TMAH) aqueous electrolyte with a special hydrate structure is explored and enables excellent cycle stability and high capacity for Mg-based alloy anodes. In this electrolyte, the Mg 0.4 Ti 0.1 Ni 0.5 alloy anode delivers a maximum discharge capacity of 466 mAh g −1 , and maintains 210 mAh g −1 after 100 cycles owing to the reduced corrosion rate , which are much better than that in 6 M KOH electrolyte, being 425 mAh g −1 and 69 mAh g −1 , respectively. Furthermore, by in-situ forming Cu coating on the Mg 0.4 Ti 0.1 Ni 0.5 electrode surface during charging process with the adding 0.01 M of Cu(OH) 2 in TMAH electrolyte, the corrosion of the electrode is further suppressed and the reversible capacity can reach 313 mAh g −1 after 100 cycles. The high conducting Cu coating can also increase the rate capability of the electrode by promoting the charge transfer. Thus, using TMAH electrolytes provides a new approach to promote the electrochemical performances of Ni-MH batteries with Mg-based alloy anodes.
研究领域:
材料科学
·
电化学
·
能源存储
·
金属腐蚀与防护
·
功能材料
·
电池技术
✓ 已验证
DOI
高影响因子
THIN SOLID FILMS
·
2018
·
IF 1.939
Yanqi Lv,Yanhong Li,Hongxia Sun,Yi Guo,Yanmei Li,Jinkun Tan,Xingfu Zhou
Crystalline yttrium-doped rutile TiO 2 nanorod arrays were synthesized and successfully implemented as a photoanode of perovskite solar cells . Study shows that yttrium was successfully doped and TiO 2 band gap changes from 3.07 eV to 3.02 eV. A positive shift of 100 mV in the flat-band potential (V fb ) was observed in Y-doped rutile TiO 2 nanorods. A power conversion efficiency of 7.95% and a photocurrent density of 15.13 mA/cm 2 were obtained for the doped sample. The photocurrent density is 1.47 times higher than that of the un-doped device. Incident photon-to-current conversion efficiency shows Y-doped device has a clear increase in quantum efficiency in the visible light range from 450 and 750 nm. Open circuit voltage decay measurements demonstrate the superior ability of Y-doped TiO 2 nanorod for separating electrons and holes and decreasing the recombination events. The improved performance is possibly attributed to the enhanced electron injection and transfer efficiency caused by a positive shift in V fb and a reduction in charge recombination. This study opens a door toward the improvement of photocurrent density of perovskite solar cell via an element doping route.
研究领域:
材料科学
·
纳米科技
·
能源化学
·
光电子学
·
半导体物理
·
可再生能源
✓ 已验证
DOI
高影响因子
VACUUM
·
2023
·
IF 4
Rui Yang,Xiangfeng Guo,Khaled Tawfik Alali,Kun Song,Lihua Jia,Tongle Ge,Xiaoshuang Chen,Dalei Song,Xuefeng Bai,Jun Wang
The construction of effective nano-microstructures electrode has been a tireless pursuit in the energy storage field. Herein, Controllable construction of diversified morphologies NiCo 2 O 4 nanomaterials by tuning the dielectric constant and viscosity of the mixed solvent. We employed different solvent compositions as deionized water (DI), DI:Ethanol (1:1), DI: Isopropanol (1:1), DI: Propylene glycol (1:1), DI: Butanediol (1:1). In mixed aqueous solvents with low dielectric constants of ethanol and isopropanol, metal ions diffuse well and the nanomaterials tend to construct sheet-like nanostructures whereas high viscosity of the propylene glycol and butanediol solution will slow down the rate of metal ion diffusion, which only grow uni-directionally to form rod-like nanostructures. The formed ear-shaped NiCo 2 O 4 nanostructures in V propylene glycol : V H2O = 1 : 1 mixed solvent have a large specific surface area and provide more electrochemically active sites, which facilitates effectively access electrolytes and thus accelerates the redox reaction rate. The resulting NiCo 2 O 4 nanoears exhibits favorable capacity of 251 mAh g −1 and excellent rate performance with a 73.0% capacity retention at 20 A g −1 . More importantly, the asymmetric supercapacitors assembled with the preferred NiCo 2 O 4 nanoears and active carbon (AC) reveal excellent electrochemical performance at operating potential of 1.6 V, great specific capacity (58.0 mAh g −1 ), energy and power density of 46.4 Wh kg −1 at 801 W kg −1 and a specific capacity retention rate of 90.7% after 5000 cycles. This work provides a new perspective for the controllable construction of new micro-nanostructure materials.
研究领域:
材料科学
·
电化学
·
纳米技术
·
能源存储
·
功能材料
·
电化学能量储存
✓ 已验证
DOI
高影响因子
Chemical Engineering and Processing-Process Intensification
·
2018
·
IF 2.826
Linchao Li,Huili Hu,Xiangguo Teng,Yuanchun Yu,Yongming Zhu,Xiaoqiang Su
The aim of this work is to prepare a hydrophobic cathode equipped with quite a few cracks for gas transfer, which can prepare H 2 O 2 in the course of electro-Fenton process. Scanning electron microscopy (SEM) and optical digital microscope are used to characterize the morphology of electrode, and an electrochemical workstation (CHI660e) is used to carry out all electrochemical studies with a conventional three-electrode system. The results demonstrate that the porous electrode is conducive to gas transmission with these cracks which can avoid the formation of bubbles. Additionally, the reaction is almost not affected by the content of dissolved oxygen and the gas flow with this structure. Under the conditions of 300 mA/cm 2 (current density), the H 2 O 2 concentration is up to 14.4 mmol/L after 30 min electrolysis with current efficiency beyond 90%. Furthermore, the cathode is successfully applied to electro-Fenton process which reduced catalyst loading. The results indicate that total degradation of MO is observed at the first 10 min, and 81% of TOC can be removed when the dosage of catalyst is 0.4 mmol/L within 60 min.
研究领域:
环境化学
·
电化学工程
·
水处理技术
·
反应器设计
·
污染物降解
✓ 已验证
DOI
高影响因子
SOLID STATE IONICS
·
2016
·
IF 2.38
Shanshan Mo,Penghao Lu,Fei Ding,Zhibin Xu,Jiaquan Liu,Xingjiang Liu,Qiang Xu
Sulfide glasses with a high lithium-ion conductivity are promising solid electrolyte for all-solid-state lithium-ion batteries. In this study, 95(0.7Li 2 S–0.3P 2 S 5 )–5Li 3 PO 4 glass electrolyte is prepared by mixing 70Li 2 S-30P 2 S 5 (mol%) glass and Li 3 PO 4 crystal using mechanical milling technique. The effects on the structures and electrochemical properties of the obtained ternary sulfide glass were examined. The ternary sulfide glass shows a good electrochemical stability, which may exhibit a wide electrochemical window up to 10 V (vs. Li/Li + ). Furthermore, the 95(0.7Li 2 S-0.3P 2 S 5 )-5Li 3 PO 4 glass electrolyte displays an electrical conductivity of 2.513 × 10 − 3 S cm − 1 at 100 °C. The all-solid-state lithium-ion cell assembled with 95(0.7Li 2 S-0.3P 2 S 5 )-5Li 3 PO 4 glass electrolyte shows a favourable cyclability, which can reveal a discharge capacity of 144 mAh g − 1 at 0.05 °C and a discharge capacity of 63.9 mAh g − 1 at 0.1C after the 50th cycle at 100 °C, respectively.
研究领域:
材料科学
·
电化学
·
能源存储
·
固态离子学
·
锂电池技术
✓ 已验证
DOI
高影响因子
Small Methods
·
2024
·Vol. 8
·期 7
·2301233
·
IF 10.7
Xiaolin Ye,Ningxin Xiong,Shaopei Huang,Qixing Wu,Hongning Chen,Xuelong Zhou
Tin-based hybrid flow batteries have demonstrated dendrite-free morphology and superior performance in terms of cycle life and energy density. However, the quick accumulation of electrodeposits near the electrode/membrane interface blocks the ion transport pathway during the charging of the battery, resulting to a very limited areal capacity (especially at high current density) that significantly hinders its deployment in long-duration storage applications. Herein, a conductivity-activity dual-gradient design is disclosed by electrically passivating the carbon felt near the membrane/electrode interface and chemically activating the carbon felt near the electrode/current collector interface. In consequence, the tin metals are preferentially plated at the region near electrode/current collector, preventing the ion transport pathway from being easily blocked. The resultant gradient electrode demonstrated an unprecedentedly high areal capacity of 268 mAh cm −2 at a current density of as high as 80 mA cm −2 . Numerical modeling and experimental characterizations show that the dual-gradient electrode differs from conventional electrodes with regard to their reaction current density distribution and electrodeposit distribution during charging. This work demonstrates a new design strategy of 3D electrodes for hybrid flow batteries to induce a desirable distribution of electrodeposits and achieve a high areal capacity at commercially relevant current densities.
研究领域:
电化学储能
·
材料科学
·
能源化学
·
电池技术
·
功能材料
·
电化学工程
✓ 已验证
DOI
高影响因子
JOURNAL OF POWER SOURCES
·
2023
·
IF 9.2
Tianyao Ding,Dong Zheng,Huainan Qu,Weixiao Ji,Xiaoxiao Zhang,Dongping Lu,Gongwei Wang,Deyang Qu
An in-situ electrochemical optical diagnosis is the key to the investigation of electrode interface during a redox reaction . Because the morphology changes particularly, dendrite formation, dendrite shapes, solid electrolyte interface formation and gas generation can be revealed visually. The challenge of ensuring uniform current density on a flat Li anode in a liquid electrolyte is addressed and uniform Li plating is demonstrated. The dendrite shape change under different reduction current density is discussed. The Li dendrite shape change and the performance of Li anodes with a surface lamination of graphite and red phosphate are used as examples to demonstrate the capability of the in-situ optical cell. An in-situ electrochemical optical cell used in the investigation of the increasingly popular solid-state Li batteries has its own challenges. Due to the untransparent nature of a solid-state electrolyte, an optical investigation on a solid-state electrolyte Li battery needs to be done by exposing the cross-section of the cell. In addition, it is very difficult to assemble an optical cell with a brittle and fragile solid-state electrolyte in a glove box. A set of formation and transfer dies, and an optical cell are introduced. The Li dendrite growth at the interface can be observed in a solid-state Li cell.
研究领域:
电化学
·
材料科学
·
能源存储
·
固态电池
·
界面科学
✓ 已验证
DOI
高影响因子
IONICS
·
2016
·Vol. 23
·期 10
·2603-2611
·
IF 2.119
Chen Shaojie,Zhao Yanran,Yang Jing,Yao Lili,Xu Xiaoxiong
Three types of inorganic electrolytes [Li 10 GeP 2 S 12 (LGPS), 75Li 2 S·24P 2 S 5 ·1P 2 O 5 (LPOS), Li 1.5 Al 0.5 Ge 1.5 (PO 4 ) 3 (LAGP)] with different particle sizes and electrochemical properties are selected as active fillers incorporated into poly(ethylene oxide) (PEO) matrix to fabricate hybrid solid electrolytes. The optimum composition of each filler is found in consideration of ionic conductivity. Their electrochemical characteristics are investigated. The optimal conductivities are 1.60 × 10 −5 , 1.18 × 10 −5 , and 2.12 × 10 −5 S cm −1 at room temperature for PEO-1%LGPS, PEO-1%LPOS, and PEO-20%LAGP, respectively. The electrochemical stability windows of these hybrid solid electrolytes are all above 5 V (vs. Li + /Li). The results show that these fillers have positive effects on the ionic conductivity, lithium ion transference number, and electrochemical stability. The relationship between the type of filler and electrochemical properties has been investigated. All-solid-state cells LiFePO 4 /Li are fabricated and present fascinating electrochemical performance with high capacity retention and good cycling stability. This work provides promising electrolytes prepared by a simple method.
研究领域:
材料科学
·
电化学
·
能源存储
·
固态离子学
·
功能材料
·
锂电池技术
✓ 已验证
DOI
高影响因子
危险品化学品经营许可证（带存储）